| Age | Commit message (Collapse) | Author |
|---|
|
DCB settings are cleared in the hardware across link events
during ifup ixgbe reprograms the hardware for DCB if it is
enabled. Now that we have two modes CEE or IEEE we need to
use the correct set of configuration data.
This patch checks the dcbx_cap bits and then enables the
device in the correct mode.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds support to use the priority assignment
table in the ieee_ets structure to map priorities to
traffic classes. Previously ixgbe only supported a
1:1 mapping. Now we can enable and disable hardware
DCB support when multiple traffic classes are actually
being used. This allows the default case all priorities
mapped to traffic class 0 to work in normal hardware
mode and utilize the full packet buffer.
This patch does not address putting the hardware in
4TC mode so packet buffer space may be underutilized
in this case. A follow up patch can address this
optimization. But at least we have the hooks to do
this now.
Also CEE will behave as it always has and map priorities
1:1 with traffic classes.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The patch below allowed IEEE 802.1Qaz and CEE DCB hardware
configurations to use common hardware set routines,
commit 88eb696cc6a7af8f9272266965b1a4dd7d6a931b
Author: John Fastabend <john.r.fastabend@intel.com>
Date: Thu Feb 10 03:02:11 2011 -0800
ixgbe: DCB, abstract out dcb_config from DCB hardware configuration
However the case when CEE link strict and group strict
are set was missed and are currently being mapped
incorrectly in some configurations.
This patch resolves this.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
RSS had previously been disabled when DCB was enabled because
DCB was single queued per traffic class. Now that DCB implements
multiple Tx/Rx rings per traffic class enable RSS.
Here RSS hashes across the queues in the traffic class.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain.@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the ndo_tc_setup to ixgbe. By default we set
the device to use strict priority.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain.@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This enables multiple {Tx|Rx} rings per traffic class while in DCB
mode. In order to get this working as expected the tc_to_tx net
device mapping is configured as well as the prio_tc_map.
skb priorities are mapped across a range of queue pairs to get
a distribution per traffic class. The maximum number of
queue pairs used while in DCB mode is capped at 64. The hardware
max is actually 128 queues but 64 is sufficient for now and
allocating more seemed a bit excessive. It is easy enough to
increase the cap later if need be.
To get the 802.1Q priority tags inserted correctly ixgbe was
previously using the skb queue_mapping field to directly set
the 802.1Q priority. This no longer works because we have removed
the 1:1 mapping between queues and traffic class. Each ring
is aligned with an 802.1Qaz traffic class so here we add an
extra field to the ring struct to identify the 802.1Q traffic
class. This uses an extra byte of the ixgbe_ring struct
fortunately there was a 2byte hole,
struct ixgbe_ring {
void * desc; /* 0 8 */
struct device * dev; /* 8 8 */
struct net_device * netdev; /* 16 8 */
union {
struct ixgbe_tx_buffer * tx_buffer_info; /* 8 */
struct ixgbe_rx_buffer * rx_buffer_info; /* 8 */
}; /* 24 8 */
long unsigned int state; /* 32 8 */
u8 atr_sample_rate; /* 40 1 */
u8 atr_count; /* 41 1 */
u16 count; /* 42 2 */
u16 rx_buf_len; /* 44 2 */
u16 next_to_use; /* 46 2 */
u16 next_to_clean; /* 48 2 */
u8 queue_index; /* 50 1 */
u8 reg_idx; /* 51 1 */
u16 work_limit; /* 52 2 */
/* XXX 2 bytes hole, try to pack */
u8 * tail; /* 56 8 */
/* --- cacheline 1 boundary (64 bytes) --- */
Now we can set the VLAN priority directly and it will be
correct. User space can indicate the 802.1Qaz priority
using the SO_PRIORITY setsocket() option and QOS layer will
steer the skb to the correct rings. Additionally using
the multiq qdisc with a queue_mapping action works as
well.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove ixgbe_fcoe_getapp() and use the generic kernel
routine instead. Also add application priority to the
kernel maintained list on setapp so applications and
stacks can query the value.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Implement ieee_setapp dcbnl ops in ixgbe. This is required
to setup FCoE which requires dedicated resources. If the
app data is not for FCoE then no action is taken in ixgbe
except to add it to the dcb_app_list.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This implements dcbnl get and set capabilities ops. The
devices supported by ixgbe can be configured to run in
IEEE or CEE modes but not both.
With the DCBX set capabilities bit we add an explicit
signal that must be used to toggle between these modes.
This patch adds logic to fail the CEE command set_hw_all()
which programs the device with a CEE configuration if
the CEE caps bit is not set. Similarly, IEEE set
commands will fail if the IEEE caps bit is not set. We
allow most CEE config set commands to occur because they
do not touch the hardware until set_hw_all() is called.
The one exception to the above is the {set|get}app routines.
These must always be protected by caps bits to ensure
side effects do not corrupt the current configured mode.
By requiring the caps bit to be set correctly we can
maintain a consistent configuration in the hardware
for CEE or IEEE modes and prevent partial hardware
configurations that may occur if user space does
not send a complete IEEE or CEE configurations.
It is expected that user space will signal a DCBX mode
before programming device.
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Tested-by: Ross Brattain <ross.b.brattain@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch updates igb version to 3.0.6.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch add DMA Coalescing which is a power-saving feature that
coalesces DMA writes in order to stay in a low-power state as much
as possible. Feature is disabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds functions and functions pointers to accommodate
differences between NVM interfaces and options for i350 devices,
82580 devices and the rest.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch adds the EEE feature for i350 devices, enabled by default.
Signed-off-by: Carolyn Wyborny <carolyn.wyborny@intel.com>
Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Change the driver string to match the PF driver string format.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The kernel version string is off by a major version number since
new silicon was just introduced and also uses the wrong format for
the version postfix.
Signed-off-by: Greg Rose <gregory.v.rose@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Josef had changed shrink_delalloc to exit after three shrink
attempts, which wasn't quite enough because new writers could
race in and steal free space.
But it also fixed deadlocks and stalls as we tried to recover
delalloc reservations. The code was tweaked to loop 1024
times, and would reset the counter any time a small amount
of progress was made. This was too drastic, and with a
lot of writers we can end up stuck in shrink_delalloc forever.
The shrink_delalloc loop is fairly complex because the caller is looping
too, and the caller will go ahead and force a transaction commit to make
sure we reclaim space.
This reworks things to exit shrink_delalloc when we've forced some
writeback and the delalloc reservations have gone down. This means
the writeback has not just started but has also finished at
least some of the metadata changes required to reclaim delalloc
space.
If we've got this wrong, we're returning ENOSPC too early, which
is a big improvement over the current behavior of hanging the machine.
Test 224 in xfstests hammers on this nicely, and with 1000 writers
trying to fill a 1GB drive we get our first ENOSPC at 93% full. The
other writers are able to continue until we get 100%.
This is a worst case test for btrfs because the 1000 writers are doing
small IO, and the small FS size means we don't have a lot of room
for metadata chunks.
Signed-off-by: Chris Mason <chris.mason@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-2.6-rt into core/futexes
futex,plist: Pass the real head of the priority list to plist_del()
futex,plist: Remove debug lock assignment from plist_node
plist: Shrink struct plist_head
plist: Add priority list test
|
|
combinations during emulation
The distance transforming in numa_emulation() used to call
numa_set_distance() for all MAX_NUMNODES * MAX_NUMNODES node
combinations regardless of which are enabled. As numa_set_distance()
ignores all out-of-bound distance settings, this doesn't cause any
problem other than looping unnecessarily many times during boot.
However, as MAX_NUMNODES * MAX_NUMNODES can be pretty high, update the
code such that it iterates through only the enabled combinations.
Yinghai Lu identified the issue and provided an initial patch to
address the issue; however, the patch was incorrect in that it didn't
build emulated distance table when there's no physical distance table
and unnecessarily complex.
http://thread.gmane.org/gmane.linux.kernel/1107986/focus=1107988
Signed-off-by: Tejun Heo <tj@kernel.org>
Reported-by: Yinghai Lu <yinghai@kernel.org>
Acked-by: Yinghai Lu <yinghai@kernel.org>
|
|
On suspend we disable all interrupts in the core code, but this does
not mask the interrupt line in the default implementation as we use a
lazy disable approach. That means we mark the interrupt disabled, but
leave the hardware unmasked. That's an optimization because we avoid
the hardware access for the common case where no interrupt happens
after we marked it disabled. If an interrupt happens, then the
interrupt flow handler masks the line at the hardware level and marks
it pending.
Suspend makes use of this delayed disable as it "disables" all
interrupts when preparing the suspend transition. Right before the
system goes into hardware suspend state it checks whether one of the
interrupts which is marked as a wakeup interrupt came in after
disabling it.
Most interrupt chips have a separate register which selects the
interrupts which can wake up the system from suspend, so we don't have
to mask any on the non wakeup interrupts.
But now we have to deal with brilliant designed hardware which lacks
such a wakeup configuration facility. For such hardware it's necessary
to mask all non wakeup interrupts before going into suspend in order
to avoid the wakeup from random interrupts.
Rather than working around this in the affected interrupt chip
implementations we can solve this elegant in the core code itself.
Add a flag IRQCHIP_MASK_ON_SUSPEND which can be set by the irq chip
implementation to indicate, that the interrupts which are not selected
as wakeup sources must be masked in the suspend path. Mask them in the
loop which checks the wakeup interrupts pending flag.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
LKML-Reference: <alpine.LFD.2.00.1103112112310.2787@localhost6.localdomain6>
|
|
The latest binutils (2.21.0.20110302/Ubuntu) breaks the build
yet another time, under CONFIG_XEN=y due to a .size directive that
refers to a slightly differently named (hence, to the now very
strict and unforgiving assembler, non-existent) symbol.
[ mingo:
This unnecessary build breakage caused by new binutils
version 2.21 gets escallated back several kernel releases spanning
several years of Linux history, affecting over 130,000 upstream
kernel commits (!), on CONFIG_XEN=y 64-bit kernels (i.e. essentially
affecting all major Linux distro kernel configs).
Git annotate tells us that this slight debug symbol code mismatch
bug has been introduced in 2008 in commit 3d75e1b8:
3d75e1b8 (Jeremy Fitzhardinge 2008-07-08 15:06:49 -0700 1231) ENTRY(xen_do_hypervisor_callback) # do_hypervisor_callback(struct *pt_regs)
The 'bug' is just a slight assymetry in ENTRY()/END()
debug-symbols sequences, with lots of assembly code between the
ENTRY() and the END():
ENTRY(xen_do_hypervisor_callback) # do_hypervisor_callback(struct *pt_regs)
...
END(do_hypervisor_callback)
Human reviewers almost never catch such small mismatches, and binutils
never even warned about it either.
This new binutils version thus breaks the Xen build on all upstream kernels
since v2.6.27, out of the blue.
This makes a straightforward Git bisection of all 64-bit Xen-enabled kernels
impossible on such binutils, for a bisection window of over hundred
thousand historic commits. (!)
This is a major fail on the side of binutils and binutils needs to turn
this show-stopper build failure into a warning ASAP. ]
Signed-off-by: Alexander van Heukelum <heukelum@fastmail.fm>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Jan Beulich <jbeulich@novell.com>
Cc: H.J. Lu <hjl.tools@gmail.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Kees Cook <kees.cook@canonical.com>
LKML-Reference: <1299877178-26063-1-git-send-email-heukelum@fastmail.fm>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s DEV_SCATTER_DMA_VIRTUAL_INFO \
"struct dev_scatter_dma_virtual_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s COMMON_CREDIT_STATE_INFO \
"struct common_credit_state_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s BUFFER_PROC_LIST \
"struct buffer_proc_list" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s ATH_DEBUG_MASK_DESCRIPTION \
"struct ath_debug_mask_description" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
We mark this as unused as well, given that I find no users,
at a later time we can determine to nuke this or not...
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR_VIRTUAL_INTERFACE_T \
"struct ar_virtual_interface" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_IRQ_PROC_REGISTERS \
"struct ar6k_irq_proc_registers" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_IRQ_ENABLE_REGISTERS \
"struct ar6k_irq_enable_registers" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_HCI_BRIDGE_INFO \
"struct ar6k_hci_bridge_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_GMBOX_INFO \
"struct ar6k_gmbox_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_GMBOX_CTRL_REGISTERS \
"struct ar6k_gmbox_ctrl_registers" drivers/staging/ath6k
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_DEVICE \
"struct ar6k_device" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6K_ASYNC_REG_IO_BUFFER \
"struct ar6k_async_reg_io_buffer" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR6000_USER_SETKEYS_INFO \
"struct ar6000_user_setkeys_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AR3K_CONFIG_INFO \
"struct ar3k_config_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s AGGR_INFO \
"struct aggr_info" drivers/staging/ath6kl/
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
remove-typedef -s A_UCHAR u8 drivers/staging/ath6kl/
This uses the remove-typedef utility:
http://www.kernel.org/pub/linux/kernel/people/mcgrof/scripts/remove-typedef
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
for i in $(find ./drivers/staging/ath6kl/ -name \*.[ch]) ; do \
sed -r -i -e "s/A_MEMCMP/memcmp/g" $i; done
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
for i in $(find ./drivers/staging/ath6kl/ -name \*.[ch]) ; do \
sed -r -i -e "s/A_MEMCPY/memcpy/g" $i; done
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The min() macro does strict type-checking so use min_t() instead
to silence a compile warning.
Cc: Naveen Singh <naveen.singh@atheros.com>
Signed-off-by: Javier Martinez Canillas <martinez.javier@gmail.com>
Signed-off-by: Luis R. Rodriguez <lrodriguez@atheros.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Move the USB_STORAGE_ENE_UB6250 entry so that it stays under the
USB_STORAGE menu.
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Fix ene_ub6250 build: it uses usb_storage driver interfaces, so it
should depend on USB_STORAGE.
ene_ub6250.c:(.text+0x14ff19): undefined reference to `usb_stor_reset_resume'
ene_ub6250.c:(.text+0x14ffb1): undefined reference to `usb_stor_bulk_transfer_buf'
ene_ub6250.c:(.text+0x14ffdd): undefined reference to `usb_stor_bulk_srb'
ene_ub6250.c:(.text+0x14fff1): undefined reference to `usb_stor_bulk_transfer_sg'
ene_ub6250.c:(.text+0x1503dd): undefined reference to `usb_stor_set_xfer_buf'
ene_ub6250.c:(.text+0x15048e): undefined reference to `usb_stor_access_xfer_buf'
ene_ub6250.c:(.text+0x150723): undefined reference to `usb_stor_probe1'
ene_ub6250.c:(.text+0x150795): undefined reference to `usb_stor_probe2'
ene_ub6250.c:(.text+0x1507af): undefined reference to `usb_stor_disconnect'
drivers/built-in.o:(.data+0x10224): undefined reference to `usb_stor_suspend'
drivers/built-in.o:(.data+0x10230): undefined reference to `usb_stor_pre_reset'
drivers/built-in.o:(.data+0x10234): undefined reference to `usb_stor_post_reset'
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
"buf" gets allocated twice in a row. It's the second allocation which
is correct. The first one should be removed.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: huajun li <huajun.li.lee@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Tegra2 USB controller doesn't properly deal with misaligned DMA
buffers, causing corruption. This is especially prevalent with USB
network adapters, where skbuff alignment is often in the middle of a
4-byte dword.
To avoid this, allocate a temporary buffer for the DMA if the provided
buffer isn't sufficiently aligned.
Signed-off-by: Robert Morell <rmorell@nvidia.com>
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
The Tegra 2 SoC has 3 EHCI compatible USB controllers. This patch adds
the necessary glue to allow the ehci-hcd driver to work on Tegra 2
SoCs.
The platform data is used to configure board-specific phy settings and
to configure the operating mode, as one of the ports may be used as a otg
port. For additional power saving, the driver supports powering down the
phy on bus suspend when it is used, for example, to connect an internal
device that use an out-of-band remote wakeup mechanism (e.g. a gpio).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Interface used by Tegra's gadget driver and ehci driver
to power on and configure the USB PHYs.
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
Add generic access ops for controllers with a ulpi viewport register
(e.g. Chipidea/ARC based controllers).
Signed-off-by: Benoit Goby <benoit@android.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
I picked up a new DAK-780EX(professional digitl reverb/mix system),
which use CH341T chipset to communication with computer on 3/2011
and the CH341T's vendor code is 1a86
Looking up the CH341T's vendor and product id's I see:
1a86 QinHeng Electronics
5523 CH341 in serial mode, usb to serial port converter
CH341T,CH341 are the products of the same company, maybe
have some common hardware, and I test the ch341.c works
well with CH341T
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: stable <stable@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
|
On a laptop I see these errors on (most) resumes:
hub 3-0:1.0: over-current change on port 1
hub 3-0:1.0: over-current change on port 2
Since over-current conditions can disappear quite quickly it's better to
downgrade that message to debug level, recheck for an over-current
condition a little later and only print and over-current condition error
if that condition (still) exists when it's rechecked.
Add similar logic to hub over-current changes. (That code is untested,
as those changes do not occur on this laptop.)
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
|
