summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2019-10-07media: dt-bindings: Fix building error for dt_binding_checkPragnesh Patel
$id doesn't match the actual filename, so update the $id Fixes: c5e8f4ccd7750 ("media: dt-bindings: media: Add Allwinner A10 CSI binding") Signed-off-by: Pragnesh Patel <pragnesh.patel@sifive.com> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-10-06arm64: dts: zii-ultra: fix ARM regulator statesLucas Stach
The GPIO controlled regulator for the ARM power supply is supplying the higher voltage when the GPIO is driven high. This is opposite to the similar regulator setup on the EVK board and is impacting stability of the board as the ARM domain has been supplied with a too low voltage when to faster OPPs are in use. Fixes: 4a13b3bec3b4 (arm64: dts: imx: add Zii Ultra board support) Signed-off-by: Lucas Stach <l.stach@pengutronix.de> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-06soc: imx: imx-scu: Getting UID from SCU should have responseAnson Huang
The SCU firmware API for getting UID should have response, otherwise, the message stored in function stack could be released and then the response data received from SCU will be stored into that released stack and cause kernel NULL pointer dump. Fixes: 73feb4d0f8f1 ("soc: imx-scu: Add SoC UID(unique identifier) support") Signed-off-by: Anson Huang <Anson.Huang@nxp.com> Signed-off-by: Shawn Guo <shawnguo@kernel.org>
2019-10-04arm64: dts: rockchip: fix RockPro64 sdhci settingsSoeren Moch
The RockPro64 schematics [1], [2] show that the rk3399 EMMC_STRB pin is connected to the RESET pin instead of the DATA_STROBE pin of the eMMC module. So the data strobe cannot be used for its intended purpose on this board, and so the HS400 eMMC mode is not functional. Limit the controller to HS200. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf [2] http://files.pine64.org/doc/rock64/PINE64_eMMC_Module_20170719.pdf Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Soeren Moch <smoch@web.de> Link: https://lore.kernel.org/r/20191003215036.15023-2-smoch@web.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-10-04arm64: dts: rockchip: fix RockPro64 vdd-log regulator settingsSoeren Moch
The RockPro64 schematic [1] page 18 states a min voltage of 0.8V and a max voltage of 1.4V for the VDD_LOG pwm regulator. However, there is an additional note that the pwm parameter needs to be modified. From the schematics a voltage range of 0.8V to 1.7V can be calculated. Additional voltage measurements on the board show that this fix indeed leads to the correct voltage, while without this fix the voltage was set too high. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Soeren Moch <smoch@web.de> Link: https://lore.kernel.org/r/20191003215036.15023-1-smoch@web.de Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-10-04ARM: multi_v7_defconfig: Fix SPI_STM32_QSPI supportPatrice Chotard
SPI_STM32_QSPI must be set in buildin as rootfs can be located on QSPI memory device. Link: https://lore.kernel.org/r/20191004124025.17394-1-patrice.chotard@st.com Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-10-04ARM: dts: logicpd-torpedo-som: Remove twl_keypadAdam Ford
The TWL4030 used on the Logit PD Torpedo SOM does not have the keypad pins routed. This patch disables the twl_keypad driver to remove some splat during boot: twl4030_keypad 48070000.i2c:twl@48:keypad: missing or malformed property linux,keymap: -22 twl4030_keypad 48070000.i2c:twl@48:keypad: Failed to build keymap twl4030_keypad: probe of 48070000.i2c:twl@48:keypad failed with error -22 Signed-off-by: Adam Ford <aford173@gmail.com> [tony@atomide.com: removed error time stamps] Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-10-04Merge tag 'fix-missing-panels' into fixesTony Lindgren
2019-10-04dt-bindings: arm: rockchip: fix Theobroma-System board bindingsHeiko Stuebner
The naming convention for the existing Theobroma boards is soc-q7module-baseboard, so rk3399-puma-haikou and the in-kernel devicetrees also follow that scheme. For some reason in the binding a wrong or outdated naming slipped in which does not match the used devicetrees and makes the dt-schema complain now. Fix this by using the names used in the wild by actual boards. Fixes: a323a513c712 ("dt-bindings: arm: Convert Rockchip board/soc bindings to json-schema") [although the issue was also present in the old txt file] Signed-off-by: Heiko Stuebner <heiko@sntech.de> Reviewed-by: Rob Herring <robh@kernel.org> Link: https://lore.kernel.org/r/20190917083453.25744-1-heiko@sntech.de
2019-10-04arm64: dts: rockchip: fix Rockpro64 RK808 interrupt lineHugh Cole-Baker
Fix the pinctrl and interrupt specifier for RK808 to use GPIO3_B2. On the Rockpro64 schematic [1] page 16, it shows GPIO3_B2 used for the interrupt line PMIC_INT_L from the RK808, and there's a note which translates as: "PMU termination GPIO1_C5 changed to this". Tested by setting an RTC wakealarm and checking /proc/interrupts counters. Without this patch, neither the rockchip_gpio_irq counter for the RK808, nor the RTC alarm counter increment when the alarm time is reached. With this patch, both interrupt counters increment by 1 as expected. [1] http://files.pine64.org/doc/rockpro64/rockpro64_v21-SCH.pdf Fixes: e4f3fb490967 ("arm64: dts: rockchip: add initial dts support for Rockpro64") Signed-off-by: Hugh Cole-Baker <sigmaris@gmail.com> Link: https://lore.kernel.org/r/20190921131457.36258-1-sigmaris@gmail.com Signed-off-by: Heiko Stuebner <heiko@sntech.de>
2019-10-03ARM: omap2plus_defconfig: Fix selected panels after generic panel changesTony Lindgren
The old omapdrm panels got removed for v5.4 in favor of generic panels, and the Kconfig options changed. Let's update omap2plus_defconfig accordingly so the same panels are still enabled. Cc: Jyri Sarha <jsarha@ti.com> Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com> Cc: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-10-03Merge tag 'omap-for-v5.4/fixes-rc1-signed' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omaps for v5.4-rc cycle Here are fixes for omaps to deal with few regressions, and to fix more boot time errors and warnings: - The recent ti-sysc interconnect target module driver changes had incorrect clock bits for both clocks and dts that cause warnings - For omap3-gta04, gpio changes caused the LCD to break a while back, and after discussing things the right fix is to set spi-cs-high - Recent omapdrm changes to use generic panels caused tfp410 to be disabled as we now must enable the generic support for it in defconfig - Recent omapdrm and backlight changes also finally made droid4 LCD to work, so let's enable it in the defconfig it can be used out of the box. This is not strictly a fix, but we still also have the older CONFIG_MFD_TI_LMU options available so this cuts down the confusion for trying to guess which display and which backlight is needed - Recent ti-sysc interconnect target module changes need the gpio module disabled on some boards, but this now needs to happen at the module level, not at the gpio driver level - Recent changes to probe system timers with ti-sysc caused warnings about mismatch in syconfig registers, so let's configure the option for RESET_STATUS as available in the TRMs - Recent changes to probe LCDC with ti-sysc caused warnings about mismatch in sysconfig registers, so let's configure the missing idlemodes for both platform data and dts as documented in TRMs - Since we moved mach-omap2 to probe with device tree, we've been getting voltage controller warnings. Turns out this code is no longer needed, so let's just remove omap2_set_init_voltage() to get rid of the pointless warnings - Configure am4372 dispc memory bandwidth to avoid underflow errors * tag 'omap-for-v5.4/fixes-rc1-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: ARM: dts: am4372: Set memory bandwidth limit for DISPC ARM: OMAP2+: Fix warnings with broken omap2_set_init_voltage() ARM: OMAP2+: Add missing LCDC midlemode for am335x ARM: OMAP2+: Fix missing reset done flag for am3 and am43 ARM: dts: Fix gpio0 flags for am335x-icev2 ARM: omap2plus_defconfig: Enable more droid4 devices as loadable modules ARM: omap2plus_defconfig: Enable DRM_TI_TFP410 DTS: ARM: gta04: introduce legacy spi-cs-high to make display work again ARM: dts: Fix wrong clocks for dra7 mcasp clk: ti: dra7: Fix mcasp8 clock bits Link: https://lore.kernel.org/r/pull-1570040410-308159@atomide.com Signed-off-by: Olof Johansson <olof@lixom.net>
2019-10-01ARM: dts: ux500: Fix up the CPU thermal zoneLinus Walleij
This fixes up the default ux500 CPU thermal zone: - Set polling delay to 0 and explain why - Set passive polling delay to 250 - Remove restrictions from the CPU cooling device, we should use all cpufreq steps to cool down if needed. Link: https://lore.kernel.org/r/20191001074628.8122-1-linus.walleij@linaro.org Fixes: b786a05f6ce4 ("ARM: dts: ux500: Update thermal zone") Suggested-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org> Signed-off-by: Olof Johansson <olof@lixom.net>
2019-09-30arm64: dts: Fix gpio to pinmux mappingRayagonda Kokatanur
There are total of 151 non-secure gpio (0-150) and four pins of pinmux (91, 92, 93 and 94) are not mapped to any gpio pin, hence update same in DT. Fixes: 8aa428cc1e2e ("arm64: dts: Add pinctrl DT nodes for Stingray SOC") Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@broadcom.com> Reviewed-by: Ray Jui <ray.jui@broadcom.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
2019-09-30arm64: dts: allwinner: a64: sopine-baseboard: Add PHY regulator delayJernej Skrabec
It turns out that sopine-baseboard needs same fix as pine64-plus for ethernet PHY. Here too Realtek ethernet PHY chip needs additional power on delay to properly initialize. Datasheet mentions that chip needs 30 ms to be properly powered on and that it needs some more time to be initialized. Fix that by adding 100ms ramp delay to regulator responsible for powering PHY. Note that issue was found out and fix tested on pine64-lts, but it's basically the same as sopine-baseboard, only layout and connectors differ. Fixes: bdfe4cebea11 ("arm64: allwinner: a64: add Ethernet PHY regulator for several boards") Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-30arm64: dts: allwinner: a64: Drop PMU nodeVasily Khoruzhick
Looks like PMU in A64 is broken, it generates no interrupts at all and as result 'perf top' shows no events. Tested on Pine64-LTS. Fixes: 34a97fcc71c2 ("arm64: dts: allwinner: a64: Add PMU node") Cc: Harald Geyer <harald@ccbib.org> Cc: Jared D. McNeill <jmcneill@NetBSD.org> Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com> Reviewed-by: Emmanuel Vadot <manu@FreeBSD.org> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-30arm64: dts: allwinner: a64: pine64-plus: Add PHY regulator delayJernej Skrabec
Depending on kernel and bootloader configuration, it's possible that Realtek ethernet PHY isn't powered on properly. According to the datasheet, it needs 30ms to power up and then some more time before it can be used. Fix that by adding 100ms ramp delay to regulator responsible for powering PHY. Fixes: 94dcfdc77fc5 ("arm64: allwinner: pine64-plus: Enable dwmac-sun8i") Suggested-by: Ondrej Jirman <megous@megous.com> Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net> Signed-off-by: Maxime Ripard <mripard@kernel.org>
2019-09-30arm64/ARM: configs: Change CONFIG_REMOTEPROC from m to yKeerthy
Commit 6334150e9a36 ("remoteproc: don't allow modular build") changes CONFIG_REMOTEPROC to a boolean from a tristate config option which inhibits all defconfigs marking CONFIG_REMOTEPROC as a module in compiling the remoteproc and dependent config options. So fix the configs to have CONFIG_REMOTEPROC built in. Link: https://lore.kernel.org/r/20190920075946.13282-5-j-keerthy@ti.com Fixes: 6334150e9a36 ("remoteproc: don't allow modular build") Signed-off-by: Keerthy <j-keerthy@ti.com> Acked-by: Will Deacon <will@kernel.org> [olof: Fixed up all 4 occurrances in this one commit] Signed-off-by: Olof Johansson <olof@lixom.net>
2019-09-30Linux 5.4-rc1Linus Torvalds
2019-09-30Merge tag 'for-5.4-rc1-tag' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux Pull btrfs fixes from David Sterba: "A bunch of fixes that accumulated in recent weeks, mostly material for stable. Summary: - fix for regression from 5.3 that prevents to use balance convert with single profile - qgroup fixes: rescan race, accounting leak with multiple writers, potential leak after io failure recovery - fix for use after free in relocation (reported by KASAN) - other error handling fixups" * tag 'for-5.4-rc1-tag' of git://git.kernel.org/pub/scm/linux/kernel/git/kdave/linux: btrfs: qgroup: Fix reserved data space leak if we have multiple reserve calls btrfs: qgroup: Fix the wrong target io_tree when freeing reserved data space btrfs: Fix a regression which we can't convert to SINGLE profile btrfs: relocation: fix use-after-free on dead relocation roots Btrfs: fix race setting up and completing qgroup rescan workers Btrfs: fix missing error return if writeback for extent buffer never started btrfs: adjust dirty_metadata_bytes after writeback failure of extent buffer Btrfs: fix selftests failure due to uninitialized i_mode in test inodes
2019-09-30Merge tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linuxLinus Torvalds
Pull csky updates from Guo Ren: "This round of csky subsystem just some fixups: - Fix mb() synchronization problem - Fix dma_alloc_coherent with PAGE_SO attribute - Fix cache_op failed when cross memory ZONEs - Optimize arch_sync_dma_for_cpu/device with dma_inv_range - Fix ioremap function losing - Fix arch_get_unmapped_area() implementation - Fix defer cache flush for 610 - Support kernel non-aligned access - Fix 610 vipt cache flush mechanism - Fix add zero_fp fixup perf backtrace panic - Move static keyword to the front of declaration - Fix csky_pmu.max_period assignment - Use generic free_initrd_mem() - entry: Remove unneeded need_resched() loop" * tag 'csky-for-linus-5.4-rc1' of git://github.com/c-sky/csky-linux: csky: Move static keyword to the front of declaration csky: entry: Remove unneeded need_resched() loop csky: Fixup csky_pmu.max_period assignment csky: Fixup add zero_fp fixup perf backtrace panic csky: Use generic free_initrd_mem() csky: Fixup 610 vipt cache flush mechanism csky: Support kernel non-aligned access csky: Fixup defer cache flush for 610 csky: Fixup arch_get_unmapped_area() implementation csky: Fixup ioremap function losing csky: Optimize arch_sync_dma_for_cpu/device with dma_inv_range csky/dma: Fixup cache_op failed when cross memory ZONEs csky: Fixup dma_alloc_coherent with PAGE_SO attribute csky: Fixup mb() synchronization problem
2019-09-30Merge tag 'armsoc-fixes' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc Pull ARM SoC fixes from Olof Johansson: "A few fixes that have trickled in through the merge window: - Video fixes for OMAP due to panel-dpi driver removal - Clock fixes for OMAP that broke no-idle quirks + nfsroot on DRA7 - Fixing arch version on ASpeed ast2500 - Two fixes for reset handling on ARM SCMI" * tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: ARM: aspeed: ast2500 is ARMv6K reset: reset-scmi: add missing handle initialisation firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle() ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux ARM: dts: am3517-evm: Fix missing video ARM: dts: logicpd-torpedo-baseboard: Fix missing video ARM: omap2plus_defconfig: Fix missing video bus: ti-sysc: Fix handling of invalid clocks bus: ti-sysc: Fix clock handling for no-idle quirks
2019-09-30ARM: dts: am4372: Set memory bandwidth limit for DISPCPeter Ujfalusi
Set memory bandwidth limit to filter out resolutions above 720p@60Hz to avoid underflow errors due to the bandwidth needs of higher resolutions. am43xx can not provide enough bandwidth to DISPC to correctly handle 'high' resolutions. Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com> Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2019-09-30Merge tag 'trace-v5.4-3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace Pull tracing fixes from Steven Rostedt: "A few more tracing fixes: - Fix a buffer overflow by checking nr_args correctly in probes - Fix a warning that is reported by clang - Fix a possible memory leak in error path of filter processing - Fix the selftest that checks for failures, but wasn't failing - Minor clean up on call site output of a memory trace event" * tag 'trace-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/rostedt/linux-trace: selftests/ftrace: Fix same probe error test mm, tracing: Print symbol name for call_site in trace events tracing: Have error path in predicate_parse() free its allocated memory tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macro tracing/probe: Fix to check the difference of nr_args before adding probe
2019-09-30Merge tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmcLinus Torvalds
Pull more MMC updates from Ulf Hansson: "A couple more updates/fixes for MMC: - sdhci-pci: Add Genesys Logic GL975x support - sdhci-tegra: Recover loss in throughput for DMA - sdhci-of-esdhc: Fix DMA bug" * tag 'mmc-v5.4-2' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc: mmc: host: sdhci-pci: Add Genesys Logic GL975x support mmc: tegra: Implement ->set_dma_mask() mmc: sdhci: Let drivers define their DMA mask mmc: sdhci-of-esdhc: set DMA snooping based on DMA coherence mmc: sdhci: improve ADMA error reporting
2019-09-30csky: Move static keyword to the front of declarationKrzysztof Wilczynski
Move the static keyword to the front of declaration of csky_pmu_of_device_ids, and resolve the following compiler warning that can be seen when building with warnings enabled (W=1): arch/csky/kernel/perf_event.c:1340:1: warning: ‘static’ is not at beginning of declaration [-Wold-style-declaration] Signed-off-by: Krzysztof Wilczynski <kw@linux.com> Signed-off-by: Guo Ren <guoren@kernel.org>
2019-09-30csky: entry: Remove unneeded need_resched() loopValentin Schneider
Since the enabling and disabling of IRQs within preempt_schedule_irq() is contained in a need_resched() loop, we don't need the outer arch code loop. Signed-off-by: Valentin Schneider <valentin.schneider@arm.com> Signed-off-by: Guo Ren <guoren@kernel.org>
2019-09-29Merge tag 'char-misc-5.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull Documentation/process update from Greg KH: "Here are two small Documentation/process/embargoed-hardware-issues.rst file updates that missed my previous char/misc pull request. The first one adds an Intel representative for the process, and the second one cleans up the text a bit more when it comes to how the disclosure rules work, as it was a bit confusing to some companies" * tag 'char-misc-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: Documentation/process: Clarify disclosure rules Documentation/process: Volunteer as the ambassador for Intel
2019-09-29Merge branch 'work.misc' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs Pull more vfs updates from Al Viro: "A couple of misc patches" * 'work.misc' of git://git.kernel.org/pub/scm/linux/kernel/git/viro/vfs: afs dynroot: switch to simple_dir_operations fs/handle.c - fix up kerneldoc
2019-09-29Merge tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6Linus Torvalds
Pull more cifs updates from Steve French: "Fixes from the recent SMB3 Test events and Storage Developer Conference (held the last two weeks). Here are nine smb3 patches including an important patch for debugging traces with wireshark, with three patches marked for stable. Additional fixes from last week to better handle some newly discovered reparse points, and a fix the create/mkdir path for setting the mode more atomically (in SMB3 Create security descriptor context), and one for path name processing are still being tested so are not included here" * tag '5.4-rc-smb3-fixes' of git://git.samba.org/sfrench/cifs-2.6: CIFS: Fix oplock handling for SMB 2.1+ protocols smb3: missing ACL related flags smb3: pass mode bits into create calls smb3: Add missing reparse tags CIFS: fix max ea value size fs/cifs/sess.c: Remove set but not used variable 'capabilities' fs/cifs/smb2pdu.c: Make SMB2_notify_init static smb3: fix leak in "open on server" perf counter smb3: allow decryption keys to be dumped by admin for debugging
2019-09-30csky: Fixup csky_pmu.max_period assignmentMao Han
The csky_pmu.max_period has type u64, and BIT() can only return 32 bits unsigned long on C-SKY. The initialization for max_period will be incorrect when count_width is bigger than 32. Use BIT_ULL() Signed-off-by: Mao Han <han_mao@c-sky.com> Signed-off-by: Guo Ren <ren_guo@c-sky.com>
2019-09-30csky: Fixup add zero_fp fixup perf backtrace panicGuo Ren
We need set fp zero to let backtrace know the end. The patch fixup perf callchain panic problem, because backtrace didn't know what is the end of fp. Signed-off-by: Guo Ren <ren_guo@c-sky.com> Reported-by: Mao Han <han_mao@c-sky.com>
2019-09-30csky: Use generic free_initrd_mem()Mike Rapoport
The csky implementation of free_initrd_mem() is an open-coded version of free_reserved_area() without poisoning. Remove it and make csky use the generic version of free_initrd_mem(). Signed-off-by: Mike Rapoport <rppt@linux.ibm.com> Signed-off-by: Guo Ren <guoren@kernel.org>
2019-09-29Merge branch 'entropy'Linus Torvalds
Merge active entropy generation updates. This is admittedly partly "for discussion". We need to have a way forward for the boot time deadlocks where user space ends up waiting for more entropy, but no entropy is forthcoming because the system is entirely idle just waiting for something to happen. While this was triggered by what is arguably a user space bug with GDM/gnome-session asking for secure randomness during early boot, when they didn't even need any such truly secure thing, the issue ends up being that our "getrandom()" interface is prone to that kind of confusion, because people don't think very hard about whether they want to block for sufficient amounts of entropy. The approach here-in is to decide to not just passively wait for entropy to happen, but to start actively collecting it if it is missing. This is not necessarily always possible, but if the architecture has a CPU cycle counter, there is a fair amount of noise in the exact timings of reasonably complex loads. We may end up tweaking the load and the entropy estimates, but this should be at least a reasonable starting point. As part of this, we also revert the revert of the ext4 IO pattern improvement that ended up triggering the reported lack of external entropy. * getrandom() active entropy waiting: Revert "Revert "ext4: make __ext4_get_inode_loc plug"" random: try to actively add entropy rather than passively wait for it
2019-09-29Revert "Revert "ext4: make __ext4_get_inode_loc plug""Linus Torvalds
This reverts commit 72dbcf72156641fde4d8ea401e977341bfd35a05. Instead of waiting forever for entropy that may just not happen, we now try to actively generate entropy when required, and are thus hopefully avoiding the problem that caused the nice ext4 IO pattern fix to be reverted. So revert the revert. Cc: Ahmed S. Darwish <darwish.07@gmail.com> Cc: Ted Ts'o <tytso@mit.edu> Cc: Willy Tarreau <w@1wt.eu> Cc: Alexander E. Patrakov <patrakov@gmail.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-29random: try to actively add entropy rather than passively wait for itLinus Torvalds
For 5.3 we had to revert a nice ext4 IO pattern improvement, because it caused a bootup regression due to lack of entropy at bootup together with arguably broken user space that was asking for secure random numbers when it really didn't need to. See commit 72dbcf721566 (Revert "ext4: make __ext4_get_inode_loc plug"). This aims to solve the issue by actively generating entropy noise using the CPU cycle counter when waiting for the random number generator to initialize. This only works when you have a high-frequency time stamp counter available, but that's the case on all modern x86 CPU's, and on most other modern CPU's too. What we do is to generate jitter entropy from the CPU cycle counter under a somewhat complex load: calling the scheduler while also guaranteeing a certain amount of timing noise by also triggering a timer. I'm sure we can tweak this, and that people will want to look at other alternatives, but there's been a number of papers written on jitter entropy, and this should really be fairly conservative by crediting one bit of entropy for every timer-induced jump in the cycle counter. Not because the timer itself would be all that unpredictable, but because the interaction between the timer and the loop is going to be. Even if (and perhaps particularly if) the timer actually happens on another CPU, the cacheline interaction between the loop that reads the cycle counter and the timer itself firing is going to add perturbations to the cycle counter values that get mixed into the entropy pool. As Thomas pointed out, with a modern out-of-order CPU, even quite simple loops show a fair amount of hard-to-predict timing variability even in the absense of external interrupts. But this tries to take that further by actually having a fairly complex interaction. This is not going to solve the entropy issue for architectures that have no CPU cycle counter, but it's not clear how (and if) that is solvable, and the hardware in question is largely starting to be irrelevant. And by doing this we can at least avoid some of the even more contentious approaches (like making the entropy waiting time out in order to avoid the possibly unbounded waiting). Cc: Ahmed Darwish <darwish.07@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Cc: Theodore Ts'o <tytso@mit.edu> Cc: Nicholas Mc Guire <hofrat@opentech.at> Cc: Andy Lutomirski <luto@kernel.org> Cc: Kees Cook <keescook@chromium.org> Cc: Willy Tarreau <w@1wt.eu> Cc: Alexander E. Patrakov <patrakov@gmail.com> Cc: Lennart Poettering <mzxreary@0pointer.de> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-09-29Merge tag 'fixes-5.4-merge-window' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into arm/fixes Fixes for omap variants Few fixes for ti-sysc interconnect target module driver for no-idle quirks that caused nfsroot to fail on some dra7 boards. And let's fixes to get LCD working again for logicpd board that got broken a while back with removal of panel-dpi driver. We need to now use generic CONFIG_DRM_PANEL_SIMPLE instead. * tag 'fixes-5.4-merge-window' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap: bus: ti-sysc: Remove unpaired sysc_clkdm_deny_idle() ARM: dts: logicpd-som-lv: Fix i2c2 and i2c3 Pin mux ARM: dts: am3517-evm: Fix missing video ARM: dts: logicpd-torpedo-baseboard: Fix missing video ARM: omap2plus_defconfig: Fix missing video bus: ti-sysc: Fix handling of invalid clocks bus: ti-sysc: Fix clock handling for no-idle quirks Link: https://lore.kernel.org/r/pull-1568819401-72461@atomide.com Signed-off-by: Olof Johansson <olof@lixom.net>
2019-09-29Merge tag 'scmi-fixes-5.4' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux into arm/fixes ARM SCMI fixes for v5.4 Couple of fixes: one in scmi reset driver initialising missed scmi handle and an other in scmi reset API implementation fixing the assignment of reset state * tag 'scmi-fixes-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/sudeep.holla/linux: reset: reset-scmi: add missing handle initialisation firmware: arm_scmi: reset: fix reset_state assignment in scmi_domain_reset Link: https://lore.kernel.org/r/20190918142139.GA4370@bogus Signed-off-by: Olof Johansson <olof@lixom.net>
2019-09-29Merge tag 'libnvdimm-fixes-5.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm More libnvdimm updates from Dan Williams: - Complete the reworks to interoperate with powerpc dynamic huge page sizes - Fix a crash due to missed accounting for the powerpc 'struct page'-memmap mapping granularity - Fix badblock initialization for volatile (DRAM emulated) pmem ranges - Stop triggering request_key() notifications to userspace when NVDIMM-security is disabled / not present - Miscellaneous small fixups * tag 'libnvdimm-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm: libnvdimm/region: Enable MAP_SYNC for volatile regions libnvdimm: prevent nvdimm from requesting key when security is disabled libnvdimm/region: Initialize bad block for volatile namespaces libnvdimm/nfit_test: Fix acpi_handle redefinition libnvdimm/altmap: Track namespace boundaries in altmap libnvdimm: Fix endian conversion issues  libnvdimm/dax: Pick the right alignment default when creating dax devices powerpc/book3s64: Export has_transparent_hugepage() related functions.
2019-09-29Merge branch 'linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal Pull thermal SoC updates from Eduardo Valentin: "This is a really small pull in the midst of a lot of pending patches. We are in the middle of restructuring how we are maintaining the thermal subsystem, as per discussion in our last LPC. For now, I am sending just some changes that were pending in my tree. Looking forward to get a more streamlined process in the next merge window" * 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal: thermal: db8500: Rewrite to be a pure OF sensor thermal: db8500: Use dev helper variable thermal: db8500: Finalize device tree conversion thermal: thermal_mmio: remove some dead code
2019-09-29Merge branch 'i2c/for-next' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux Pull more i2c updates from Wolfram Sang: - make Lenovo Yoga C630 boot now that the dependencies are merged - restore BlockProcessCall for i801, accidently removed in this merge window - a bugfix for the riic driver - an improvement to the slave-eeprom driver which should have been in the first pull request but sadly got lost in the process * 'i2c/for-next' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: i2c: slave-eeprom: Add read only mode i2c: i801: Bring back Block Process Call support for certain platforms i2c: riic: Clear NACK in tend isr i2c: qcom-geni: Disable DMA processing on the Lenovo Yoga C630
2019-09-29Merge tag 'iommu-fixes-5.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull iommu fixes from Joerg Roedel: "A couple of fixes for the AMD IOMMU driver have piled up: - Some fixes for the reworked IO page-table which caused memory leaks or did not allow to downgrade mappings under some conditions. - Locking fixes to fix a couple of possible races around accessing 'struct protection_domain'. The races got introduced when the dma-ops path became lock-less in the fast-path" * tag 'iommu-fixes-5.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: iommu/amd: Lock code paths traversing protection_domain->dev_list iommu/amd: Lock dev_data in attach/detach code paths iommu/amd: Check for busy devices earlier in attach_device() iommu/amd: Take domain->lock for complete attach/detach path iommu/amd: Remove amd_iommu_devtable_lock iommu/amd: Remove domain->updated iommu/amd: Wait for completion of IOTLB flush in attach_device iommu/amd: Unmap all L7 PTEs when downgrading page-sizes iommu/amd: Introduce first_pte_l7() helper iommu/amd: Fix downgrading default page-sizes in alloc_pte() iommu/amd: Fix pages leak in free_pagetable()
2019-09-29Documentation/process: Clarify disclosure rulesThomas Gleixner
The role of the contact list provided by the disclosing party and how it affects the disclosure process and the ability to include experts into the development process is not really well explained. Neither is it entirely clear when the disclosing party will be informed about the fact that a developer who is not covered by an employer NDA needs to be brought in and disclosed. Explain the role of the contact list and the information policy along with an eventual conflict resolution better. Reported-by: Dave Hansen <dave.hansen@linux.intel.com> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Acked-by: Dave Hansen <dave.hansen@linux.intel.com> Link: https://lore.kernel.org/r/alpine.DEB.2.21.1909251028390.10825@nanos.tec.linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-09-28Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netLinus Torvalds
Pull networking fixes from David Miller: 1) Sanity check URB networking device parameters to avoid divide by zero, from Oliver Neukum. 2) Disable global multicast filter in NCSI, otherwise LLDP and IPV6 don't work properly. Longer term this needs a better fix tho. From Vijay Khemka. 3) Small fixes to selftests (use ping when ping6 is not present, etc.) from David Ahern. 4) Bring back rt_uses_gateway member of struct rtable, it's semantics were not well understood and trying to remove it broke things. From David Ahern. 5) Move usbnet snaity checking, ignore endpoints with invalid wMaxPacketSize. From Bjørn Mork. 6) Missing Kconfig deps for sja1105 driver, from Mao Wenan. 7) Various small fixes to the mlx5 DR steering code, from Alaa Hleihel, Alex Vesker, and Yevgeny Kliteynik 8) Missing CAP_NET_RAW checks in various places, from Ori Nimron. 9) Fix crash when removing sch_cbs entry while offloading is enabled, from Vinicius Costa Gomes. 10) Signedness bug fixes, generally in looking at the result given by of_get_phy_mode() and friends. From Dan Crapenter. 11) Disable preemption around BPF_PROG_RUN() calls, from Eric Dumazet. 12) Don't create VRF ipv6 rules if ipv6 is disabled, from David Ahern. 13) Fix quantization code in tcp_bbr, from Kevin Yang. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (127 commits) net: tap: clean up an indentation issue nfp: abm: fix memory leak in nfp_abm_u32_knode_replace tcp: better handle TCP_USER_TIMEOUT in SYN_SENT state sk_buff: drop all skb extensions on free and skb scrubbing tcp_bbr: fix quantization code to not raise cwnd if not probing bandwidth mlxsw: spectrum_flower: Fail in case user specifies multiple mirror actions Documentation: Clarify trap's description mlxsw: spectrum: Clear VLAN filters during port initialization net: ena: clean up indentation issue NFC: st95hf: clean up indentation issue net: phy: micrel: add Asym Pause workaround for KSZ9021 net: socionext: ave: Avoid using netdev_err() before calling register_netdev() ptp: correctly disable flags on old ioctls lib: dimlib: fix help text typos net: dsa: microchip: Always set regmap stride to 1 nfp: flower: fix memory leak in nfp_flower_spawn_vnic_reprs nfp: flower: prevent memory leak in nfp_flower_spawn_phy_reprs net/sched: Set default of CONFIG_NET_TC_SKB_EXT to N vrf: Do not attempt to create IPv6 mcast rule if IPv6 is disabled net: sched: sch_sfb: don't call qdisc_put() while holding tree lock ...
2019-09-28Merge branch 'hugepage-fallbacks' (hugepatch patches from David Rientjes)Linus Torvalds
Merge hugepage allocation updates from David Rientjes: "We (mostly Linus, Andrea, and myself) have been discussing offlist how to implement a sane default allocation strategy for hugepages on NUMA platforms. With these reverts in place, the page allocator will happily allocate a remote hugepage immediately rather than try to make a local hugepage available. This incurs a substantial performance degradation when memory compaction would have otherwise made a local hugepage available. This series reverts those reverts and attempts to propose a more sane default allocation strategy specifically for hugepages. Andrea acknowledges this is likely to fix the swap storms that he originally reported that resulted in the patches that removed __GFP_THISNODE from hugepage allocations. The immediate goal is to return 5.3 to the behavior the kernel has implemented over the past several years so that remote hugepages are not immediately allocated when local hugepages could have been made available because the increased access latency is untenable. The next goal is to introduce a sane default allocation strategy for hugepages allocations in general regardless of the configuration of the system so that we prevent thrashing of local memory when compaction is unlikely to succeed and can prefer remote hugepages over remote native pages when the local node is low on memory." Note on timing: this reverts the hugepage VM behavior changes that got introduced fairly late in the 5.3 cycle, and that fixed a huge performance regression for certain loads that had been around since 4.18. Andrea had this note: "The regression of 4.18 was that it was taking hours to start a VM where 3.10 was only taking a few seconds, I reported all the details on lkml when it was finally tracked down in August 2018. https://lore.kernel.org/linux-mm/20180820032640.9896-2-aarcange@redhat.com/ __GFP_THISNODE in MADV_HUGEPAGE made the above enterprise vfio workload degrade like in the "current upstream" above. And it still would have been that bad as above until 5.3-rc5" where the bad behavior ends up happening as you fill up a local node, and without that change, you'd get into the nasty swap storm behavior due to compaction working overtime to make room for more memory on the nodes. As a result 5.3 got the two performance fix reverts in rc5. However, David Rientjes then noted that those performance fixes in turn regressed performance for other loads - although not quite to the same degree. He suggested reverting the reverts and instead replacing them with two small changes to how hugepage allocations are done (patch descriptions rephrased by me): - "avoid expensive reclaim when compaction may not succeed": just admit that the allocation failed when you're trying to allocate a huge-page and compaction wasn't successful. - "allow hugepage fallback to remote nodes when madvised": when that node-local huge-page allocation failed, retry without forcing the local node. but by then I judged it too late to replace the fixes for a 5.3 release. So 5.3 was released with behavior that harked back to the pre-4.18 logic. But now we're in the merge window for 5.4, and we can see if this alternate model fixes not just the horrendous swap storm behavior, but also restores the performance regression that the late reverts caused. Fingers crossed. * emailed patches from David Rientjes <rientjes@google.com>: mm, page_alloc: allow hugepage fallback to remote nodes when madvised mm, page_alloc: avoid expensive reclaim when compaction may not succeed Revert "Revert "Revert "mm, thp: consolidate THP gfp handling into alloc_hugepage_direct_gfpmask"" Revert "Revert "mm, thp: restore node-local hugepage allocations""
2019-09-28selftests/ftrace: Fix same probe error testSteven Rostedt (VMware)
The "same probe" selftest that tests that adding the same probe fails doesn't add the same probe and passes, which fails the test. Fixes: b78b94b82122 ("selftests/ftrace: Update kprobe event error testcase") Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2019-09-28mm, tracing: Print symbol name for call_site in trace eventsChangbin Du
To improve the readability of raw slab trace points, print the call_site ip using '%pS'. Then we can grep events with function names. [002] .... 808.188897: kmem_cache_free: call_site=putname+0x47/0x50 ptr=00000000cef40c80 [002] .... 808.188898: kfree: call_site=security_cred_free+0x42/0x50 ptr=0000000062400820 [002] .... 808.188904: kmem_cache_free: call_site=put_cred_rcu+0x88/0xa0 ptr=0000000058d74ef8 [002] .... 808.188913: kmem_cache_alloc: call_site=prepare_creds+0x26/0x100 ptr=0000000058d74ef8 bytes_req=168 bytes_alloc=576 gfp_flags=GFP_KERNEL [002] .... 808.188917: kmalloc: call_site=security_prepare_creds+0x77/0xa0 ptr=0000000062400820 bytes_req=8 bytes_alloc=336 gfp_flags=GFP_KERNEL|__GFP_ZERO [002] .... 808.188920: kmem_cache_alloc: call_site=getname_flags+0x4f/0x1e0 ptr=00000000cef40c80 bytes_req=4096 bytes_alloc=4480 gfp_flags=GFP_KERNEL [002] .... 808.188925: kmem_cache_free: call_site=putname+0x47/0x50 ptr=00000000cef40c80 [002] .... 808.188926: kfree: call_site=security_cred_free+0x42/0x50 ptr=0000000062400820 [002] .... 808.188931: kmem_cache_free: call_site=put_cred_rcu+0x88/0xa0 ptr=0000000058d74ef8 Link: http://lkml.kernel.org/r/20190914103215.23301-1-changbin.du@gmail.com Signed-off-by: Changbin Du <changbin.du@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2019-09-28tracing: Have error path in predicate_parse() free its allocated memoryNavid Emamdoost
In predicate_parse, there is an error path that is not going to out_free instead it returns directly which leads to a memory leak. Link: http://lkml.kernel.org/r/20190920225800.3870-1-navid.emamdoost@gmail.com Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2019-09-28tracing: Fix clang -Wint-in-bool-context warnings in IF_ASSIGN macroNathan Chancellor
After r372664 in clang, the IF_ASSIGN macro causes a couple hundred warnings along the lines of: kernel/trace/trace_output.c:1331:2: warning: converting the enum constant to a boolean [-Wint-in-bool-context] kernel/trace/trace.h:409:3: note: expanded from macro 'trace_assign_type' IF_ASSIGN(var, ent, struct ftrace_graph_ret_entry, ^ kernel/trace/trace.h:371:14: note: expanded from macro 'IF_ASSIGN' WARN_ON(id && (entry)->type != id); \ ^ 264 warnings generated. This warning can catch issues with constructs like: if (state == A || B) where the developer really meant: if (state == A || state == B) This is currently the only occurrence of the warning in the kernel tree across defconfig, allyesconfig, allmodconfig for arm32, arm64, and x86_64. Add the implicit '!= 0' to the WARN_ON statement to fix the warnings and find potential issues in the future. Link: https://github.com/llvm/llvm-project/commit/28b38c277a2941e9e891b2db30652cfd962f070b Link: https://github.com/ClangBuiltLinux/linux/issues/686 Link: http://lkml.kernel.org/r/20190926162258.466321-1-natechancellor@gmail.com Reviewed-by: Nick Desaulniers <ndesaulniers@google.com> Signed-off-by: Nathan Chancellor <natechancellor@gmail.com> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
2019-09-28tracing/probe: Fix to check the difference of nr_args before adding probeMasami Hiramatsu
Steven reported that a test triggered: ================================================================== BUG: KASAN: slab-out-of-bounds in trace_kprobe_create+0xa9e/0xe40 Read of size 8 at addr ffff8880c4f25a48 by task ftracetest/4798 CPU: 2 PID: 4798 Comm: ftracetest Not tainted 5.3.0-rc6-test+ #30 Hardware name: Hewlett-Packard HP Compaq Pro 6300 SFF/339A, BIOS K01 v03.03 07/14/2016 Call Trace: dump_stack+0x7c/0xc0 ? trace_kprobe_create+0xa9e/0xe40 print_address_description+0x6c/0x332 ? trace_kprobe_create+0xa9e/0xe40 ? trace_kprobe_create+0xa9e/0xe40 __kasan_report.cold.6+0x1a/0x3b ? trace_kprobe_create+0xa9e/0xe40 kasan_report+0xe/0x12 trace_kprobe_create+0xa9e/0xe40 ? print_kprobe_event+0x280/0x280 ? match_held_lock+0x1b/0x240 ? find_held_lock+0xac/0xd0 ? fs_reclaim_release.part.112+0x5/0x20 ? lock_downgrade+0x350/0x350 ? kasan_unpoison_shadow+0x30/0x40 ? __kasan_kmalloc.constprop.6+0xc1/0xd0 ? trace_kprobe_create+0xe40/0xe40 ? trace_kprobe_create+0xe40/0xe40 create_or_delete_trace_kprobe+0x2e/0x60 trace_run_command+0xc3/0xe0 ? trace_panic_handler+0x20/0x20 ? kasan_unpoison_shadow+0x30/0x40 trace_parse_run_command+0xdc/0x163 vfs_write+0xe1/0x240 ksys_write+0xba/0x150 ? __ia32_sys_read+0x50/0x50 ? tracer_hardirqs_on+0x61/0x180 ? trace_hardirqs_off_caller+0x43/0x110 ? mark_held_locks+0x29/0xa0 ? do_syscall_64+0x14/0x260 do_syscall_64+0x68/0x260 Fix to check the difference of nr_args before adding probe on existing probes. This also may set the error log index bigger than the number of command parameters. In that case it sets the error position is next to the last parameter. Link: http://lkml.kernel.org/r/156966474783.3478.13217501608215769150.stgit@devnote2 Fixes: ca89bc071d5e ("tracing/kprobe: Add multi-probe per event support") Reported-by: Steven Rostedt (VMware) <rostedt@goodmis.org> Signed-off-by: Masami Hiramatsu <mhiramat@kernel.org> Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
generated by cgit (git 2.34.1) at 2025-09-14 13:47:30 +0000