| Age | Commit message (Collapse) | Author |
|---|
|
Add EE and AO domains pins for the i2s output clocks and data to the gxbb
device tree.
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The ODroid-C2 on-board USB Hub needs to to have it's reset signal set to
high level in order to be enumerated by the USB Host Controller.
But this management must be part of the currently in-development Generic
Power Sequence patch that will allow a USB Controller driver to start and stop
a power sequence associated to the USB Bus.
In the meantime, a simple USB Hog will work to enable the USB Hub.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The same Mali-450 MP3 GPU is present in the GXBB and GXL SoCs.
The node is simply added in the meson-gxbb.dtsi file.
For GXL, since a lot is shared with the GXM that has a Mali-T820 IP, this
patch adds a new meson-gxl-mali.dtsi and is included in the SoC specific
dtsi files.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
[khilman: s/MALI/Mali in changelog]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Orange Pi PC 2 board features a OTG port like the one on older H3 Orange
Pi's, with PG12 pin being the id det pin and PL2 being the vbus driver
pin.
Add support for it.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Orange Pi PC 2 is a typical single board computer using the
Allwinner H5 SoC. Apart from the usual suspects it features three
separately driven USB ports and a Gigabit Ethernet port.
Also it has a SPI NOR flash soldered, from which the board can boot
from. This enables the SBC to behave like a "real computer" with
built-in firmware.
Add the board specific .dts file, which includes the H5 .dtsi and
enables the peripherals that we support so far.
Reviewed-by: Rask Ingemann Lambertsen <rask@formelder.dk>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: dropped all GPIO pinctrl nodes, change red LED gpio,
change MMC cd to active-low, rename some node names to prevent
underscores]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The Allwinner H5 SoC is pin-compatible to the H3 SoC, but uses
Cortex-A53 cores instead.
Based on the now shared base .dtsi describing the common peripherals
describe the H5 specific nodes on top of that.
That symlinks in the sunxi-h3-h5.dtsi from the arch/arm tree.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: add H5 pinctrl compatible, and changes for my h3-h5 dtsi
refactor, commit message changed to meet new arm64 naming scheme,
drop H3 pinctrl compatible because of interrupt bank change, drop
H3 ccu compatible because of clock change, drop ccu node as it come
into h3-h5 dtsi]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Allwinner H3/H5 have a dual-routed USB PHY0 -- routed to either OHCI/EHCI
or MUSB controller.
Add device nodes for these controllers.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The new Allwinner H5 SoC is pin-compatible to the H3 SoC, but with the
Cortex-A7 cores replaced by Cortex-A53 cores and the MMC controller
updated. So we should really share almost the whole .dtsi.
In preparation for that move the peripheral parts of the existing
sun8i-h3.dtsi into a new sunxi-h3-h5.dtsi.
The actual sun8i-h3.dtsi then includes that and defines the H3 specific
parts on top of it.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
[Icenowy: also split out mmc and gic, as well as pio and ccu's
compatible, and make drop of skeleton into a seperated patch]
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
According to the datasheets provided by Allwinner, both Allwinner H3 and
H5 use GIC-400 as their interrupt controller.
For better device tree reusing, correct the GIC compatible in H3 DTSI to
"arm,gic-400", thus this node can be reused in H5.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
After converting to generic pinconf binding, pinctrl-a10.h is now not
used at all.
Drop its inclusion for H3 DTSI.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
The skeleton.dtsi file is now deprecated, and do not exist in ARM64
environment.
Since we will soon reuse most part of H3 DTSI for H5, which is an ARM64
chip, drop skeleton.dtsi inclusion now.
Signed-off-by: Icenowy Zheng <icenowy@aosc.xyz>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
Add pinctrl pins nodes following the additions of missing pins in the pinctrl
driver.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
It adds VOU tvenc device in zx296718.dtsi, so that boards with TV
connector can enable the support by changing 'status' in board DTS file.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
It adds VOU DPC device and enables HDMI support, which includes both
display and audio through SPDIF interface.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Add three mmc devices for zx296718 SoC, and enable the SD and eMMMC on
zx296718-evb board.
Signed-off-by: Jun Nie <jun.nie@linaro.org>
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Rather than a fixed rate clock, pll_vga is a PLL can be programmed into
different freqencies. Let's drop it from device tree and get it
registered from clock driver.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
|
|
Prepend the compatible strings with a GX generic name in nodes compatible with
the GXBB HW and keep the same scheme as other nodes.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Since we know the GXBB and GXL/GXM share more hardware, we can safely move
the remaining peripheral nodes present in the GXBB dtsi to the common GX dtsi.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The Khadas VIM series consists of two boards which are almost
identical:
They are both using the same GXL S905X SoC, 100Mbit/s ethernet
(through the SoC-internal PHY), 2GB DDR3 memory, a micro-SD card slot,
onboard eMMC, Broadcom based SDIO WIFI, 2x USB A and 1x USB Type-C (the
latter with OTG support). The red LED is driven by PWM_AO_B (which
allows dimming), while the blue LED is managed by the firmware.
The differences are:
- the VIM Pro has a 16GB eMMC module, while the VIM only has 8GB
- the VIM Pro uses an AP6255 a/b/g/n/ac WIFI module, while the VIM comes
with an AP6212 b/g/n SDIO WIFI module
(the Vim uses an 8GB eMMC module, while
The boards are based on Amlogic's GXL S905X P212 reference design, which
is why most of the functionality (all MMC controllers and power
sequences, IR remote input, the main UART, ADC and ethernet) is simply
inherited from meson-gxl-s905x-p212.dtsi.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
Khadas is a new sub-brand of "Shenzhen Wesion Technology Co., Ltd.".
They are developing Amlogic and Rockchip based "DIY boxes" (single board
computers): http://khadas.com/
They are best know for their latest product: the Khadas VIM (an Amlogic
GXL S905X based SBC).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This adds the new DT nodes for the missing PWM pins in the EE and AO
domain.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This commit adds the description of the PPv2.2 hardware block for the
Marvell Armada 7K and Armada 8K processors, and their corresponding Armada
7040 and 8040 Development boards.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The Armada 3720 DB board has an RTC on the I2C bus. It's a PT7C4337A from
Pericom but which claims to be fully compatible with the ds1337.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Now that the gpio expander is present in the dts, use it to add an USB3
PHY using one of these gpio as a regulator.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
Now that clocks are available provide a clock resource for xhci node.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
IRQ number for xhci controller was wrong, fix it.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
|
|
The wrong GPIO line was provided here.
Fixes: ef8d2ffedf18 ("ARM64: dts: meson-gxbb: add MMC support")
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch describes the GPIO lines usage on the Odroid-C2 board.
This is useful in the debugfs gpio file and using the cdev gpio API.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This patch adds support for the P230 and Q200 ADC laddered button and
GPIO button.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
We need to enable this regulator before the digitizer can be used. Wacom
recommended waiting for 100 ms before talking to the HID.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[store chip ident as comment until i2c multi-compatibles are sorted]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
It's suggested to fix the domain number for all PCIe
host bridges or not set it at all. However, if we don't
fix it, the domain number will keep increasing ever when
doing unbind/bind test, which makes the bus tree of lspci
introduce pointless domain hierarchy. More investigation shows
the domain number allocater of PCI doesn't consider the conflict
of domain number if we have more than one PCIe port belonging to
different domains. So once unbinding/binding one of them and keep
others would going to overflow the domain number so that finally
it will share the same domain as others, but actually it shouldn't.
We should fix the domain number for PCIe or invent new indexing
ID mechanisms. However it isn't worth inventing new indexing ID
mechanisms personlly, Just look at how other Root Complex drivers
did, for instance, broadcom and qualcomm, it seems fixing the domain
number was more popular. So this patch gonna fix the domain number
of PCIe for rk3399.
Signed-off-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Brian Norris <briannorris@chromium.org>
Tested-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
dw-mmc got its reset-properties specified, so add the softresets
for it on the rk3399.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Shawn Lin <shawn.lin@rock-chips.com>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
dw-mmc got its reset-properties specified, so add the softresets
for it on the rk3368.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Reviewed-by: Shawn Lin <shawn.lin@rock-chips.com>
|
|
Default to disable mailbox in rk3368 core dts file.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
I2S of RK3368 SoCs keep same as RK3066 SoCs found on Rockchip,
add nodes to support them.
Signed-off-by: Jianqun Xu <jay.xu@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add dmac bus and dmac peri dts nodes for peripherals,
such as I2S, SPI, UART and so on.
Signed-off-by: Huibin Hong <huibin.hong@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
As reported by Lorenzo, the residency/latency values defined in the
idle-state for rk3368 "make no sense". When introducing them I
simply took the idle-state node from the vendor kernel in error
as I didn't look up if these values were sane in the first place.
Talking to people and determining why they were used in this way
showed that it was meant to make sure the cpu_suspend callback
got initialized which at the 3.10 time was somehow required even
for wfi-based idle handling.
Of course the generic arch_cpu_idle() now does wfi-based idle-handling
already and the rk3368 does not implement any other idle states than
the default WFI, so these wrong idle-states should go away.
Reported-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Acked-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
Used for Gru/Kevin only, as they're the only ones which have a described
CPU regulator. Also, I'm not sure we've validated this table non-Gru
boards.
At the same time, partially describe PWM regulators for Gru, so cpufreq
doesn't think it can crank up the clock speed without changing the
voltage. However, we don't yet have the DT bindings to fully describe
the Over Voltage Protection (OVP) circuits on these boards. Without that
description, we might end up changing the voltage too much, too fast.
Add the pwm-regulator descriptions and associate the CPU OPPs, but leave
them disabled.
Signed-off-by: Brian Norris <briannorris@chromium.org>
[shared gru/kevin parts on a gru device]
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[with a bit of reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Kevin is part of a family of boards called Gru. As best as possible, the
properties shared by the Gru family are placed in rk3399-gru.dtsi, while
Kevin-specific bits are in rk3399-gru-kevin.dts. This does not add full
support for the base Gru board.
Working and tested (to some extent):
* EC support -- including keyboard, battery, PWM, and probably more
* UART / console
* Thermal
* Touchscreen
* Touchpad
* Digitizer (regulator still WIP)
* PCIe / Wifi
* Bluetooth / Webcam
* SD card
* eMMC
* USB2 on TypeC
- This works much of the time, but USB3 devices may or may not detect
properly. Waiting on proper extcon support for USB3 over TypeC.
- Depends on XHCI/DWC3 fixes for ARM64 that still haven't landed
* Backlight
Not working:
* CPUFreq -- relies on special OVP support for our PWM regulator
circuits
* EC / extcon support -- and with it, USB3/TypeC/DP
* DRM -- won't even build on ARM64, so all display, eDP, etc. is not
enabled
Not tested:
* Audio
Signed-off-by: Brian Norris <briannorris@chromium.org>
[shared gru/kevin parts on a gru device]
Tested-by: Enric Balletbo i Serra <enric.balletbo@collabora.com>
[with a bit of reordering]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Gru is a base dev board for a family of devices, including Kevin. Both
utilize Rockchip RK3399, and they share much of their design.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Acked-by: Rob Herring <robh@kernel.org>
[added Samsung Chromebook Plus hint]
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
Add the dwc3 usb needed node information for rk3399.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas into next/dt64
Renesas ARM64 Based SoC DT Updates for v4.12
Cleanup:
* Drop superfluous status update for frequency override from all
r8a779[56] boards
* Tidyup Audio-DMAC channel for DVC for r8a7795 SoC
* Remove unit-address and reg from integrated cache on r8a779[56] SoCs
Enhancements:
* Add all Cortex-A53 and Cortex-A57 CPU cores to r8a7796 SoC
* Add Cortex-A53 CPU cores to r8a7795 SoC
* Update memory node to 4 GiB map on h3ulcb board
* Upgrade to PSCI v1.0 to support Suspend-to-RAM on r8a779[56] SoCs
* Add SCIF1 (DEBUG1) to r8a7796/salvator-x board
* Add all SCIF and HSCIF nodes with DMA enabled to r8a7796 SoC
* Set drive-strength for ravb pins for r8a7795/salvator-x board
* Enable gigabit ethernet on r8a779[56]/salvator-x boards
* Enable I2C for DVFS device r8a779[56]/salvator-x boards
* tag 'renesas-arm64-dt-for-v4.12' of https://git.kernel.org/pub/scm/linux/kernel/git/horms/renesas: (32 commits)
arm64: dts: r8a7796: salvator-x: Drop superfluous status update for frequency override
arm64: dts: m3ulcb: Drop superfluous status update for frequency override
arm64: dts: r8a7795: salvator-x: Drop superfluous status updates for frequency overrides
arm64: dts: h3ulcb: Drop superfluous status update for frequency override
arm64: dts: r8a7796: Add Cortex-A53 PMU node
arm64: dts: r8a7796: Add Cortex-A53 CPU cores
arm64: dts: r8a7796: Add CA53 L2 cache-controller node
arm64: dts: r8a7796: Add Cortex-A57 PMU node
arm64: dts: r8a7796: Add Cortex-A57 CPU cores
arm64: dts: r8a7795: Tidyup Audio-DMAC channel for DVC
arm64: dts: r8a7795: salvator-x: Set drive-strength for ravb pins
arm64: dts: r8a7796: Remove unit-address and reg from integrated cache
arm64: dts: r8a7795: Remove unit-addresses and regs from integrated caches
arm64: dts: r8a7796: Upgrade to PSCI v1.0 to support Suspend-to-RAM
arm64: dts: r8a7795: Upgrade to PSCI v1.0 to support Suspend-to-RAM
arm64: dts: r8a7795: Add Cortex-A53 PMU node
arm64: dts: r8a7795: Add Cortex-A53 CPU cores
arm64: dts: r8a7796: Enable HSCIF DMA
arm64: dts: r8a7796: salvator-x: add SCIF1 (DEBUG1)
arm64: dts: r8a7796: Enable SCIF DMA
...
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
* shared/dt-symlinks:
arm64: dts: add arm/arm64 include symlinks
ARM: dts: add arm/arm64 include symlinks
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Allow including of dtsi files in an architecture-independent manner.
Some dtsi files may be shared between architectures and one suggestion
was to have symlinks and let these includes get accessed via a
#include <arm64/foo.dtsi>
So add the necessary symlinks for arm32.
Suggested-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
