| Age | Commit message (Collapse) | Author |
|---|
|
cid value is not being verified in wmi_evt_delba(),
verification is added.
Signed-off-by: Alexei Avshalom Lazar <ailizaro@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to compiler optimization, it's possible that dr_bit (descriptor
ready) is read last from the status message.
Due to race condition between HW writing the status message and
driver reading it, other fields that were read earlier (before dr_bit)
could have invalid values.
Fix this by explicitly reading the dr_bit first and then using rmb
before reading the rest of the status message.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Fix a race between cfg80211 add_key call and transmitting of 4/4 EAP
packet. In case the transmit is delayed until after the add key takes
place, message 4/4 will be encrypted with the new key, and the
receiver side (AP) will drop it due to MIC error.
Wil6210 will monitor and look for the transmitted packet 4/4 eap key.
In case add_key takes place before the transmission completed, then
wil6210 will let the FW store the key and wil6210 will notify the FW
to use the PTK key only after 4/4 eap packet transmission was
completed.
Signed-off-by: Ahmad Masri <amasri@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
PMC is a hardware debug mechanism which allows capturing real time
debug data and stream it to host memory. The driver allocates memory
buffers and set them inside PMC ring of descriptors.
Add pmcring debugfs that application can use to read the binary
content of descriptors inside the PMC ring (cat pmcring).
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Move common part of wil_netif_rx_any into new helper function and add
support for non-gro receive using netif_rx_ni.
Signed-off-by: Dedy Lansky <dlansky@codeaurora.org>
Signed-off-by: Maya Erez <merez@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The tlv targets such as WCN3990 send more data in the chan info event, which is
not sent by the non tlv targets. There is a minimum size check in the wmi event
for non-tlv targets and hence we cannot update the common channel info
structure as it was done in commit 13104929d2ec ("ath10k: fill the channel
survey results for WCN3990 correctly"). This broke channel survey results on
10.x firmware versions.
If the common channel info structure is updated, the size check for chan info
event for non-tlv targets will fail and return -EPROTO and we see the below
error messages
ath10k_pci 0000:01:00.0: failed to parse chan info event: -71
Add tlv specific channel info structure and restore the original size of the
common channel info structure to mitigate this issue.
Tested HW: WCN3990
QCA9887
Tested FW: WLAN.HL.3.1-00784-QCAHLSWMTPLZ-1
10.2.4-1.0-00037
Fixes: 13104929d2ec ("ath10k: fill the channel survey results for WCN3990 correctly")
Cc: stable@vger.kernel.org # 5.0
Signed-off-by: Rakesh Pillai <pillair@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When the FW bundles multiple packets, pkt->act_len may be incorrect
as it refers to the first packet only (however, the FW will only
bundle packets that fit into the same pkt->alloc_len).
Before this patch, the skb length would be set (incorrectly) to
pkt->act_len in ath10k_sdio_mbox_rx_packet, and then later manually
adjusted in ath10k_sdio_mbox_rx_process_packet.
The first problem is that ath10k_sdio_mbox_rx_process_packet does not
use proper skb_put commands to adjust the length (it directly changes
skb->len), so we end up with a mismatch between skb->head + skb->tail
and skb->data + skb->len. This is quite serious, and causes corruptions
in the TCP stack, as the stack tries to coalesce packets, and relies
on skb->tail being correct (that is, skb_tail_pointer must point to
the first byte_after_ the data).
Instead of re-adjusting the size in ath10k_sdio_mbox_rx_process_packet,
this moves the code to ath10k_sdio_mbox_rx_packet, and also add a
bounds check, as skb_put would crash the kernel if not enough space is
available.
Tested with QCA6174 SDIO with firmware
WLAN.RMH.4.4.1-00007-QCARMSWP-1.
Fixes: 8530b4e7b22bc3b ("ath10k: sdio: set skb len for all rx packets")
Signed-off-by: Nicolas Boichat <drinkcat@chromium.org>
Signed-off-by: Wen Gong <wgong@codeaurora.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
My wave-1 firmware often crashes when I am bringing down
AP vdevs, and sometimes at least some machines lockup hard
after spewing IOMMU errors.
I don't see the same issue in STA mode, so I suspect beacons
are the issue.
Moving the beacon buf deletion to later in the vdev teardown
logic appears to help this problem. Firmware still crashes
often, but several iterations did not show IOMMU errors and
machine didn't hang.
Tested hardware: QCA9880
Tested firmware: ath10k-ct from beginning of 2019, exact version unknown
Signed-off-by: Ben Greear <greearb@candelatech.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Due to shift of priorities the actual status of the subsystem is Odd Fixes.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
The userptr put_pages can be called from inside try_to_unmap, and so
enters with the page lock held on one of the object's backing pages. We
cannot take the page lock ourselves for fear of recursion.
Reported-by: Lionel Landwerlin <lionel.g.landwerlin@intel.com>
Reported-by: Martin Wilck <Martin.Wilck@suse.com>
Reported-by: Leo Kraav <leho@kraav.com>
Fixes: aa56a292ce62 ("drm/i915/userptr: Acquire the page lock around set_page_dirty()")
References: https://bugzilla.kernel.org/show_bug.cgi?id=203317
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Tvrtko Ursulin <tvrtko.ursulin@intel.com>
Cc: Jani Nikula <jani.nikula@intel.com>
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux
Pull clone3 fix from Christian Brauner:
"This is a last-minute bugfix for clone3() that should go in before we
release 5.3 with clone3().
clone3() did not verify that the exit_signal argument was set to a
valid signal. This can be used to cause a crash by specifying a signal
greater than NSIG. e.g. -1.
The commit from Eugene adds a check to copy_clone_args_from_user() to
verify that the exit signal is limited by CSIGNAL as with legacy
clone() and that the signal is valid. With this we don't get the
legacy clone behavior were an invalid signal could be handed down and
would only be detected and then ignored in do_notify_parent(). Users
of clone3() will now get a proper error right when they pass an
invalid exit signal. Note, that this is not a change in user-visible
behavior since no kernel with clone3() has been released yet"
* tag 'for-linus-20190912' of gitolite.kernel.org:pub/scm/linux/kernel/git/brauner/linux:
fork: block invalid exit signals with clone3()
|
|
These files are not covered in globs from any other .gitignore files.
Signed-off-by: Jeroen Roovers <jer@gentoo.org>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Ingo Molnar:
"A KVM guest fix, and a kdump kernel relocation errors fix"
* 'x86-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/timer: Force PIT initialization when !X86_FEATURE_ARAT
x86/purgatory: Change compiler flags from -mcmodel=kernel to -mcmodel=large to fix kexec relocation errors
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
drm-misc-fixes for v5.3 final:
- Constify modes whitelist harder.
- Fix lima driver gem_wait ioctl.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/99e52e7a-d4ce-6a2c-0501-bc559a710955@linux.intel.com
|
|
cecf5d87ff20 ("block: split .sysfs_lock into two locks") starts to
release & actuire sysfs_lock again during switching elevator. So it
isn't enough to prevent switching elevator from happening by simply
clearing QUEUE_FLAG_REGISTERED with holding sysfs_lock, because
in-progress switch still can move on after re-acquiring the lock,
meantime the flag of QUEUE_FLAG_REGISTERED won't get checked.
Fixes this issue by checking 'q->elevator' directly & locklessly after
q->kobj is removed in blk_unregister_queue(), this way is safe because
q->elevator can't be changed at that time.
Fixes: cecf5d87ff20 ("block: split .sysfs_lock into two locks")
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hannes Reinecke <hare@suse.com>
Cc: Greg KH <gregkh@linuxfoundation.org>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Currently blk_set_runtime_active() is checking if q->dev is null by
itself, thus remove the same checking in its user: scsi_dev_type_resume().
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some devices may skip blk_pm_runtime_init() and have null pointer
in its request_queue->dev. For example, SCSI devices of UFS Well-Known
LUNs.
Currently the null pointer is checked by the user of
blk_set_runtime_active(), i.e., scsi_dev_type_resume(). It is better to
check it by blk_set_runtime_active() itself instead of by its users.
Signed-off-by: Stanley Chu <stanley.chu@mediatek.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
Final drm/i915 fixes for v5.3:
- Fox DP MST high color depth regression
- Fix GPU hangs on Vulkan compute workloads
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/877e6e27qm.fsf@intel.com
|
|
Previously, higher 32 bits of exit_signal fields were lost when copied
to the kernel args structure (that uses int as a type for the respective
field). Moreover, as Oleg has noted, exit_signal is used unchecked, so
it has to be checked for sanity before use; for the legacy syscalls,
applying CSIGNAL mask guarantees that it is at least non-negative;
however, there's no such thing is done in clone3() code path, and that
can break at least thread_group_leader.
This commit adds a check to copy_clone_args_from_user() to verify that
the exit signal is limited by CSIGNAL as with legacy clone() and that
the signal is valid. With this we don't get the legacy clone behavior
were an invalid signal could be handed down and would only be detected
and ignored in do_notify_parent(). Users of clone3() will now get a
proper error when they pass an invalid exit signal. Note, that this is
not user-visible behavior since no kernel with clone3() has been
released yet.
The following program will cause a splat on a non-fixed clone3() version
and will fail correctly on a fixed version:
#define _GNU_SOURCE
#include <linux/sched.h>
#include <linux/types.h>
#include <sched.h>
#include <stdio.h>
#include <stdlib.h>
#include <sys/syscall.h>
#include <sys/wait.h>
#include <unistd.h>
int main(int argc, char *argv[])
{
pid_t pid = -1;
struct clone_args args = {0};
args.exit_signal = -1;
pid = syscall(__NR_clone3, &args, sizeof(struct clone_args));
if (pid < 0)
exit(EXIT_FAILURE);
if (pid == 0)
exit(EXIT_SUCCESS);
wait(NULL);
exit(EXIT_SUCCESS);
}
Fixes: 7f192e3cd316 ("fork: add clone3")
Reported-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Oleg Nesterov <oleg@redhat.com>
Suggested-by: Dmitry V. Levin <ldv@altlinux.org>
Signed-off-by: Eugene Syromiatnikov <esyr@redhat.com>
Link: https://lore.kernel.org/r/4b38fa4ce420b119a4c6345f42fe3cec2de9b0b5.1568223594.git.esyr@redhat.com
[christian.brauner@ubuntu.com: simplify check and rework commit message]
Signed-off-by: Christian Brauner <christian.brauner@ubuntu.com>
|
|
When the userspace program runs the KVM_S390_INTERRUPT ioctl to inject
an interrupt, we convert them from the legacy struct kvm_s390_interrupt
to the new struct kvm_s390_irq via the s390int_to_s390irq() function.
However, this function does not take care of all types of interrupts
that we can inject into the guest later (see do_inject_vcpu()). Since we
do not clear out the s390irq values before calling s390int_to_s390irq(),
there is a chance that we copy random data from the kernel stack which
could be leaked to the userspace later.
Specifically, the problem exists with the KVM_S390_INT_PFAULT_INIT
interrupt: s390int_to_s390irq() does not handle it, and the function
__inject_pfault_init() later copies irq->u.ext which contains the
random kernel stack data. This data can then be leaked either to
the guest memory in __deliver_pfault_init(), or the userspace might
retrieve it directly with the KVM_S390_GET_IRQ_STATE ioctl.
Fix it by handling that interrupt type in s390int_to_s390irq(), too,
and by making sure that the s390irq struct is properly pre-initialized.
And while we're at it, make sure that s390int_to_s390irq() now
directly returns -EINVAL for unknown interrupt types, so that we
immediately get a proper error code in case we add more interrupt
types to do_inject_vcpu() without updating s390int_to_s390irq()
sometime in the future.
Cc: stable@vger.kernel.org
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>
Link: https://lore.kernel.org/kvm/20190912115438.25761-1-thuth@redhat.com
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
The '.exit' functions from 'pernet_operations' structure should be marked
as __net_exit, not __net_init.
Fixes: 8e2d61e0aed2 ("sctp: fix race on protocol/netns initialization")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Acked-by: Marcelo Ricardo Leitner <marcelo.leitner@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix several spelling typos in comments in t4_hw.c.
Signed-off-by: Arkadiusz Drabczyk <arkadiusz@drabczyk.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux into arm/drivers
Qualcomm ARM Based Driver Updates for v5.4
* Add AOSS QMP support
* Various fixups for Qualcomm SCM
* Add socinfo driver
* Add SoC serial number attribute and associated APIs
* Add SM8150 and SC7180 support in Qualcomm SCM
* Fixup max processor count in SMEM
* tag 'qcom-drivers-for-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/qcom/linux:
soc: qcom: aoss: Add AOSS QMP support
dt-bindings: soc: qcom: aoss: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: Add SM8150 and SC7180 support
dt-bindings: firmware: scm: re-order compatible list
soc: qcom: smem: Update max processor count
soc: qcom: socinfo: Annotate switch cases with fall through
soc: qcom: Extend AOSS QMP driver to support resources that are used to wake up the SoC.
soc: qcom: socinfo: Expose image information
soc: qcom: socinfo: Expose custom attributes
soc: qcom: Add socinfo driver
base: soc: Export soc_device_register/unregister APIs
base: soc: Add serial_number attribute to soc
firmware: qcom_scm: Cleanup code in qcom_scm_assign_mem()
firmware: qcom_scm: Fix some typos in docs and printks
firmware: qcom_scm: Use proper types for dma mappings
|
|
The ixgbe driver currently does IPsec TX offloading
based on an existing secpath. However, the secpath
can also come from the RX side, in this case it is
misinterpreted for TX offload and the packets are
dropped with a "bad sa_idx" error. Fix this by using
the xfrm_offload() function to test for TX offload.
Fixes: 592594704761 ("ixgbe: process the Tx ipsec offload")
Reported-by: Michael Marley <michael@michaelmarley.com>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lock_extent_buffer_io() returns 1 to the caller to tell it everything
went fine and the callers needs to start writeback for the extent buffer
(submit a bio, etc), 0 to tell the caller everything went fine but it does
not need to start writeback for the extent buffer, and a negative value if
some error happened.
When it's about to return 1 it tries to lock all pages, and if a try lock
on a page fails, and we didn't flush any existing bio in our "epd", it
calls flush_write_bio(epd) and overwrites the return value of 1 to 0 or
an error. The page might have been locked elsewhere, not with the goal
of starting writeback of the extent buffer, and even by some code other
than btrfs, like page migration for example, so it does not mean the
writeback of the extent buffer was already started by some other task,
so returning a 0 tells the caller (btree_write_cache_pages()) to not
start writeback for the extent buffer. Note that epd might currently have
either no bio, so flush_write_bio() returns 0 (success) or it might have
a bio for another extent buffer with a lower index (logical address).
Since we return 0 with the EXTENT_BUFFER_WRITEBACK bit set on the
extent buffer and writeback is never started for the extent buffer,
future attempts to writeback the extent buffer will hang forever waiting
on that bit to be cleared, since it can only be cleared after writeback
completes. Such hang is reported with a trace like the following:
[49887.347053] INFO: task btrfs-transacti:1752 blocked for more than 122 seconds.
[49887.347059] Not tainted 5.2.13-gentoo #2
[49887.347060] "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message.
[49887.347062] btrfs-transacti D 0 1752 2 0x80004000
[49887.347064] Call Trace:
[49887.347069] ? __schedule+0x265/0x830
[49887.347071] ? bit_wait+0x50/0x50
[49887.347072] ? bit_wait+0x50/0x50
[49887.347074] schedule+0x24/0x90
[49887.347075] io_schedule+0x3c/0x60
[49887.347077] bit_wait_io+0x8/0x50
[49887.347079] __wait_on_bit+0x6c/0x80
[49887.347081] ? __lock_release.isra.29+0x155/0x2d0
[49887.347083] out_of_line_wait_on_bit+0x7b/0x80
[49887.347084] ? var_wake_function+0x20/0x20
[49887.347087] lock_extent_buffer_for_io+0x28c/0x390
[49887.347089] btree_write_cache_pages+0x18e/0x340
[49887.347091] do_writepages+0x29/0xb0
[49887.347093] ? kmem_cache_free+0x132/0x160
[49887.347095] ? convert_extent_bit+0x544/0x680
[49887.347097] filemap_fdatawrite_range+0x70/0x90
[49887.347099] btrfs_write_marked_extents+0x53/0x120
[49887.347100] btrfs_write_and_wait_transaction.isra.4+0x38/0xa0
[49887.347102] btrfs_commit_transaction+0x6bb/0x990
[49887.347103] ? start_transaction+0x33e/0x500
[49887.347105] transaction_kthread+0x139/0x15c
So fix this by not overwriting the return value (ret) with the result
from flush_write_bio(). We also need to clear the EXTENT_BUFFER_WRITEBACK
bit in case flush_write_bio() returns an error, otherwise it will hang
any future attempts to writeback the extent buffer, and undo all work
done before (set back EXTENT_BUFFER_DIRTY, etc).
This is a regression introduced in the 5.2 kernel.
Fixes: 2e3c25136adfb ("btrfs: extent_io: add proper error handling to lock_extent_buffer_for_io()")
Fixes: f4340622e0226 ("btrfs: extent_io: Move the BUG_ON() in flush_write_bio() one level up")
Reported-by: Zdenek Sojka <zsojka@seznam.cz>
Link: https://lore.kernel.org/linux-btrfs/GpO.2yos.3WGDOLpx6t%7D.1TUDYM@seznam.cz/T/#u
Reported-by: Stefan Priebe - Profihost AG <s.priebe@profihost.ag>
Link: https://lore.kernel.org/linux-btrfs/5c4688ac-10a7-fb07-70e8-c5d31a3fbb38@profihost.ag/T/#t
Reported-by: Drazen Kacar <drazen.kacar@oradian.com>
Link: https://lore.kernel.org/linux-btrfs/DB8PR03MB562876ECE2319B3E579590F799C80@DB8PR03MB5628.eurprd03.prod.outlook.com/
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=204377
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
Sometimes when fsync'ing a file we need to log that other inodes exist and
when we need to do that we acquire a reference on the inodes and then drop
that reference using iput() after logging them.
That generally is not a problem except if we end up doing the final iput()
(dropping the last reference) on the inode and that inode has a link count
of 0, which can happen in a very short time window if the logging path
gets a reference on the inode while it's being unlinked.
In that case we end up getting the eviction callback, btrfs_evict_inode(),
invoked through the iput() call chain which needs to drop all of the
inode's items from its subvolume btree, and in order to do that, it needs
to join a transaction at the helper function evict_refill_and_join().
However because the task previously started a transaction at the fsync
handler, btrfs_sync_file(), it has current->journal_info already pointing
to a transaction handle and therefore evict_refill_and_join() will get
that transaction handle from btrfs_join_transaction(). From this point on,
two different problems can happen:
1) evict_refill_and_join() will often change the transaction handle's
block reserve (->block_rsv) and set its ->bytes_reserved field to a
value greater than 0. If evict_refill_and_join() never commits the
transaction, the eviction handler ends up decreasing the reference
count (->use_count) of the transaction handle through the call to
btrfs_end_transaction(), and after that point we have a transaction
handle with a NULL ->block_rsv (which is the value prior to the
transaction join from evict_refill_and_join()) and a ->bytes_reserved
value greater than 0. If after the eviction/iput completes the inode
logging path hits an error or it decides that it must fallback to a
transaction commit, the btrfs fsync handle, btrfs_sync_file(), gets a
non-zero value from btrfs_log_dentry_safe(), and because of that
non-zero value it tries to commit the transaction using a handle with
a NULL ->block_rsv and a non-zero ->bytes_reserved value. This makes
the transaction commit hit an assertion failure at
btrfs_trans_release_metadata() because ->bytes_reserved is not zero but
the ->block_rsv is NULL. The produced stack trace for that is like the
following:
[192922.917158] assertion failed: !trans->bytes_reserved, file: fs/btrfs/transaction.c, line: 816
[192922.917553] ------------[ cut here ]------------
[192922.917922] kernel BUG at fs/btrfs/ctree.h:3532!
[192922.918310] invalid opcode: 0000 [#1] SMP DEBUG_PAGEALLOC PTI
[192922.918666] CPU: 2 PID: 883 Comm: fsstress Tainted: G W 5.1.4-btrfs-next-47 #1
[192922.919035] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.11.2-0-gf9626ccb91-prebuilt.qemu-project.org 04/01/2014
[192922.919801] RIP: 0010:assfail.constprop.25+0x18/0x1a [btrfs]
(...)
[192922.920925] RSP: 0018:ffffaebdc8a27da8 EFLAGS: 00010286
[192922.921315] RAX: 0000000000000051 RBX: ffff95c9c16a41c0 RCX: 0000000000000000
[192922.921692] RDX: 0000000000000000 RSI: ffff95cab6b16838 RDI: ffff95cab6b16838
[192922.922066] RBP: ffff95c9c16a41c0 R08: 0000000000000000 R09: 0000000000000000
[192922.922442] R10: ffffaebdc8a27e70 R11: 0000000000000000 R12: ffff95ca731a0980
[192922.922820] R13: 0000000000000000 R14: ffff95ca84c73338 R15: ffff95ca731a0ea8
[192922.923200] FS: 00007f337eda4e80(0000) GS:ffff95cab6b00000(0000) knlGS:0000000000000000
[192922.923579] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[192922.923948] CR2: 00007f337edad000 CR3: 00000001e00f6002 CR4: 00000000003606e0
[192922.924329] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[192922.924711] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[192922.925105] Call Trace:
[192922.925505] btrfs_trans_release_metadata+0x10c/0x170 [btrfs]
[192922.925911] btrfs_commit_transaction+0x3e/0xaf0 [btrfs]
[192922.926324] btrfs_sync_file+0x44c/0x490 [btrfs]
[192922.926731] do_fsync+0x38/0x60
[192922.927138] __x64_sys_fdatasync+0x13/0x20
[192922.927543] do_syscall_64+0x60/0x1c0
[192922.927939] entry_SYSCALL_64_after_hwframe+0x49/0xbe
(...)
[192922.934077] ---[ end trace f00808b12068168f ]---
2) If evict_refill_and_join() decides to commit the transaction, it will
be able to do it, since the nested transaction join only increments the
transaction handle's ->use_count reference counter and it does not
prevent the transaction from getting committed. This means that after
eviction completes, the fsync logging path will be using a transaction
handle that refers to an already committed transaction. What happens
when using such a stale transaction can be unpredictable, we are at
least having a use-after-free on the transaction handle itself, since
the transaction commit will call kmem_cache_free() against the handle
regardless of its ->use_count value, or we can end up silently losing
all the updates to the log tree after that iput() in the logging path,
or using a transaction handle that in the meanwhile was allocated to
another task for a new transaction, etc, pretty much unpredictable
what can happen.
In order to fix both of them, instead of using iput() during logging, use
btrfs_add_delayed_iput(), so that the logging path of fsync never drops
the last reference on an inode, that step is offloaded to a safe context
(usually the cleaner kthread).
The assertion failure issue was sporadically triggered by the test case
generic/475 from fstests, which loads the dm error target while fsstress
is running, which lead to fsync failing while logging inodes with -EIO
errors and then trying later to commit the transaction, triggering the
assertion failure.
CC: stable@vger.kernel.org # 4.4+
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Filipe Manana <fdmanana@suse.com>
Signed-off-by: David Sterba <dsterba@suse.com>
|
|
as target for memset()
If userspace doesn't set KVM_MEM_LOG_DIRTY_PAGES on memslot before calling
kvm_s390_vm_start_migration(), kernel will oops with:
Unable to handle kernel pointer dereference in virtual kernel address space
Failing address: 0000000000000000 TEID: 0000000000000483
Fault in home space mode while using kernel ASCE.
AS:0000000002a2000b R2:00000001bff8c00b R3:00000001bff88007 S:00000001bff91000 P:000000000000003d
Oops: 0004 ilc:2 [#1] SMP
...
Call Trace:
([<001fffff804ec552>] kvm_s390_vm_set_attr+0x347a/0x3828 [kvm])
[<001fffff804ecfc0>] kvm_arch_vm_ioctl+0x6c0/0x1998 [kvm]
[<001fffff804b67e4>] kvm_vm_ioctl+0x51c/0x11a8 [kvm]
[<00000000008ba572>] do_vfs_ioctl+0x1d2/0xe58
[<00000000008bb284>] ksys_ioctl+0x8c/0xb8
[<00000000008bb2e2>] sys_ioctl+0x32/0x40
[<000000000175552c>] system_call+0x2b8/0x2d8
INFO: lockdep is turned off.
Last Breaking-Event-Address:
[<0000000000dbaf60>] __memset+0xc/0xa0
due to ms->dirty_bitmap being NULL, which might crash the host.
Make sure that ms->dirty_bitmap is set before using it or
return -EINVAL otherwise.
Cc: <stable@vger.kernel.org>
Fixes: afdad61615cc ("KVM: s390: Fix storage attributes migration with memory slots")
Signed-off-by: Igor Mammedov <imammedo@redhat.com>
Link: https://lore.kernel.org/kvm/20190911075218.29153-1-imammedo@redhat.com/
Reviewed-by: David Hildenbrand <david@redhat.com>
Reviewed-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: Claudio Imbrenda <imbrenda@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Janosch Frank <frankja@linux.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
In qrtr_tun_write_iter the allocated kbuf should be release in case of
error or success return.
v2 Update: Thanks to David Miller for pointing out the release on success
path as well.
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In event of failure during register_netdevice, free_netdev is
invoked immediately. free_netdev assumes that all the netdevice
refcounts have been dropped prior to it being called and as a
result frees and clears out the refcount pointer.
However, this is not necessarily true as some of the operations
in the NETDEV_UNREGISTER notifier handlers queue RCU callbacks for
invocation after a grace period. The IPv4 callback in_dev_rcu_put
tries to access the refcount after free_netdev is called which
leads to a null de-reference-
44837.761523: <6> Unable to handle kernel paging request at
virtual address 0000004a88287000
44837.761651: <2> pc : in_dev_finish_destroy+0x4c/0xc8
44837.761654: <2> lr : in_dev_finish_destroy+0x2c/0xc8
44837.762393: <2> Call trace:
44837.762398: <2> in_dev_finish_destroy+0x4c/0xc8
44837.762404: <2> in_dev_rcu_put+0x24/0x30
44837.762412: <2> rcu_nocb_kthread+0x43c/0x468
44837.762418: <2> kthread+0x118/0x128
44837.762424: <2> ret_from_fork+0x10/0x1c
Fix this by waiting for the completion of the call_rcu() in
case of register_netdevice errors.
Fixes: 93ee31f14f6f ("[NET]: Fix free_netdev on register_netdev failure.")
Cc: Sean Tranchetti <stranche@codeaurora.org>
Signed-off-by: Subash Abhinov Kasiviswanathan <subashab@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
George McCollister says:
====================
add ksz9567 with I2C support to ksz9477 driver
Resurrect KSZ9477 I2C driver support patch originally sent to the list
by Tristram Ha and resolve outstanding issues. It now works as similarly to
the ksz9477 SPI driver as possible, using the same regmap macros.
Add support for ksz9567 to the ksz9477 driver (tested on a board with
ksz9567 connected via I2C).
Remove NET_DSA_TAG_KSZ_COMMON since it's not needed.
Changes since v1:
Put ksz9477_i2c.c includes in alphabetical order.
Added Reviewed-Bys.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the superfluous NET_DSA_TAG_KSZ_COMMON and just use the existing
NET_DSA_TAG_KSZ. Update the description to mention the three switch
families it supports. No functional change.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the KSZ9567 7-Port Gigabit Ethernet Switch to the
ksz9477 driver. The KSZ9567 supports both SPI and I2C. Oddly the
ksz9567 is already in the device tree binding documentation.
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add KSZ9477 I2C driver support. The code ksz9477.c and ksz_common.c are
used together to generate the I2C driver.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
[george.mccollister@gmail.com: bring up to date, use ksz_common regmap macros]
Signed-off-by: George McCollister <george.mccollister@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The '.exit' functions from 'pernet_operations' structure should be marked
as __net_exit, not __net_init.
Fixes: d862e5461423 ("net: ipv6: Implement /proc/net/icmp6.")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I got a UAF repport in tun driver when doing fuzzy test:
[ 466.269490] ==================================================================
[ 466.271792] BUG: KASAN: use-after-free in tun_chr_read_iter+0x2ca/0x2d0
[ 466.271806] Read of size 8 at addr ffff888372139250 by task tun-test/2699
[ 466.271810]
[ 466.271824] CPU: 1 PID: 2699 Comm: tun-test Not tainted 5.3.0-rc1-00001-g5a9433db2614-dirty #427
[ 466.271833] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS rel-1.12.1-0-ga5cab58e9a3f-prebuilt.qemu.org 04/01/2014
[ 466.271838] Call Trace:
[ 466.271858] dump_stack+0xca/0x13e
[ 466.271871] ? tun_chr_read_iter+0x2ca/0x2d0
[ 466.271890] print_address_description+0x79/0x440
[ 466.271906] ? vprintk_func+0x5e/0xf0
[ 466.271920] ? tun_chr_read_iter+0x2ca/0x2d0
[ 466.271935] __kasan_report+0x15c/0x1df
[ 466.271958] ? tun_chr_read_iter+0x2ca/0x2d0
[ 466.271976] kasan_report+0xe/0x20
[ 466.271987] tun_chr_read_iter+0x2ca/0x2d0
[ 466.272013] do_iter_readv_writev+0x4b7/0x740
[ 466.272032] ? default_llseek+0x2d0/0x2d0
[ 466.272072] do_iter_read+0x1c5/0x5e0
[ 466.272110] vfs_readv+0x108/0x180
[ 466.299007] ? compat_rw_copy_check_uvector+0x440/0x440
[ 466.299020] ? fsnotify+0x888/0xd50
[ 466.299040] ? __fsnotify_parent+0xd0/0x350
[ 466.299064] ? fsnotify_first_mark+0x1e0/0x1e0
[ 466.304548] ? vfs_write+0x264/0x510
[ 466.304569] ? ksys_write+0x101/0x210
[ 466.304591] ? do_preadv+0x116/0x1a0
[ 466.304609] do_preadv+0x116/0x1a0
[ 466.309829] do_syscall_64+0xc8/0x600
[ 466.309849] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 466.309861] RIP: 0033:0x4560f9
[ 466.309875] Code: 00 00 66 2e 0f 1f 84 00 00 00 00 00 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 b8 ff ff ff f7 d8 64 89 01 48
[ 466.309889] RSP: 002b:00007ffffa5166e8 EFLAGS: 00000206 ORIG_RAX: 0000000000000127
[ 466.322992] RAX: ffffffffffffffda RBX: 0000000000400460 RCX: 00000000004560f9
[ 466.322999] RDX: 0000000000000003 RSI: 00000000200008c0 RDI: 0000000000000003
[ 466.323007] RBP: 00007ffffa516700 R08: 0000000000000004 R09: 0000000000000000
[ 466.323014] R10: 0000000000000000 R11: 0000000000000206 R12: 000000000040cb10
[ 466.323021] R13: 0000000000000000 R14: 00000000006d7018 R15: 0000000000000000
[ 466.323057]
[ 466.323064] Allocated by task 2605:
[ 466.335165] save_stack+0x19/0x80
[ 466.336240] __kasan_kmalloc.constprop.8+0xa0/0xd0
[ 466.337755] kmem_cache_alloc+0xe8/0x320
[ 466.339050] getname_flags+0xca/0x560
[ 466.340229] user_path_at_empty+0x2c/0x50
[ 466.341508] vfs_statx+0xe6/0x190
[ 466.342619] __do_sys_newstat+0x81/0x100
[ 466.343908] do_syscall_64+0xc8/0x600
[ 466.345303] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 466.347034]
[ 466.347517] Freed by task 2605:
[ 466.348471] save_stack+0x19/0x80
[ 466.349476] __kasan_slab_free+0x12e/0x180
[ 466.350726] kmem_cache_free+0xc8/0x430
[ 466.351874] putname+0xe2/0x120
[ 466.352921] filename_lookup+0x257/0x3e0
[ 466.354319] vfs_statx+0xe6/0x190
[ 466.355498] __do_sys_newstat+0x81/0x100
[ 466.356889] do_syscall_64+0xc8/0x600
[ 466.358037] entry_SYSCALL_64_after_hwframe+0x49/0xbe
[ 466.359567]
[ 466.360050] The buggy address belongs to the object at ffff888372139100
[ 466.360050] which belongs to the cache names_cache of size 4096
[ 466.363735] The buggy address is located 336 bytes inside of
[ 466.363735] 4096-byte region [ffff888372139100, ffff88837213a100)
[ 466.367179] The buggy address belongs to the page:
[ 466.368604] page:ffffea000dc84e00 refcount:1 mapcount:0 mapping:ffff8883df1b4f00 index:0x0 compound_mapcount: 0
[ 466.371582] flags: 0x2fffff80010200(slab|head)
[ 466.372910] raw: 002fffff80010200 dead000000000100 dead000000000122 ffff8883df1b4f00
[ 466.375209] raw: 0000000000000000 0000000000070007 00000001ffffffff 0000000000000000
[ 466.377778] page dumped because: kasan: bad access detected
[ 466.379730]
[ 466.380288] Memory state around the buggy address:
[ 466.381844] ffff888372139100: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 466.384009] ffff888372139180: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 466.386131] >ffff888372139200: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 466.388257] ^
[ 466.390234] ffff888372139280: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 466.392512] ffff888372139300: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb
[ 466.394667] ==================================================================
tun_chr_read_iter() accessed the memory which freed by free_netdev()
called by tun_set_iff():
CPUA CPUB
tun_set_iff()
alloc_netdev_mqs()
tun_attach()
tun_chr_read_iter()
tun_get()
tun_do_read()
tun_ring_recv()
register_netdevice() <-- inject error
goto err_detach
tun_detach_all() <-- set RCV_SHUTDOWN
free_netdev() <-- called from
err_free_dev path
netdev_freemem() <-- free the memory
without check refcount
(In this path, the refcount cannot prevent
freeing the memory of dev, and the memory
will be used by dev_put() called by
tun_chr_read_iter() on CPUB.)
(Break from tun_ring_recv(),
because RCV_SHUTDOWN is set)
tun_put()
dev_put() <-- use the memory
freed by netdev_freemem()
Put the publishing of tfile->tun after register_netdevice(),
so tun_get() won't get the tun pointer that freed by
err_detach path if register_netdevice() failed.
Fixes: eb0fb363f920 ("tuntap: attach queue 0 before registering netdevice")
Reported-by: Hulk Robot <hulkci@huawei.com>
Suggested-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull virtio fixes from Michael Tsirkin:
"Last minute bugfixes.
A couple of security things.
And an error handling bugfix that is never encountered by most people,
but that also makes it kind of safe to push at the last minute, and it
helps push the fix to stable a bit sooner"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
vhost: make sure log_num < in_num
vhost: block speculation of translated descriptors
virtio_ring: fix unmap of indirect descriptors
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull perf fix from Ingo Molnar:
"Fix an initialization bug in the hw-breakpoints, which triggered on
the ARM platform"
* 'perf-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
perf/hw_breakpoint: Fix arch_hw_breakpoint use-before-initialization
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fix from Ingo Molnar:
"Fix a race in the IRQ resend mechanism, which can result in a NULL
dereference crash"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
genirq: Prevent NULL pointer dereference in resend_irqs()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fix from Linus Walleij:
"Hopefully last pin control fix: a single patch for some Aspeed
problems. The BMCs are much happier now"
* tag 'pinctrl-v5.3-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: aspeed: Fix spurious mux failures on the AST2500
|
|
Using temporaries for gasket_page_table entries to remove scnprintf()
statements and reduce line length, as suggested by Joe Perches. Thanks!
Signed-off-by: Sandro Volery <sandro@volery.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190910061928.GA9623@volery
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
strcpy was used multiple times in strcpy to write into dev->name.
I replaced them with strscpy.
Signed-off-by: Sandro Volery <sandro@volery.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190911062359.GA14886@volery
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When the number of bytes to be printed exceeds the limit snprintf
returns the number of bytes that would have been printed (if there was
no truncation). This might cause issues, hence use scnprintf which
returns the actual number of bytes printed to buffer always
Signed-off-by: Rohit Sarkar <rohitsarkar5398@gmail.com>
Reviewed-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/20190911135112.GA5569@SARKAR
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The IRQ handler(isr_bh_routine()) was called twice for each interrupt
from firmware. The data was read completely during the first call and
the second call was doing nothing.
Now changed the IRQ flag from ‘level’ to ‘edge’ trigger i.e
IRQF_TRIGGER_LOW to IRQF_TRIGGER_FALLING to avoid extra interrupt
trigger.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/20190910074514.3073-2-ajay.kathat@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove interrupt handling for unused interrupt status(PLL update and
Sleep). The firmware only initiates the interrupt for the data transfer
to host and rest are not used anymore.
Signed-off-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/20190910074514.3073-1-ajay.kathat@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 1329 bytes.
Before:
text data bss dec hex filename
5581 1488 64 7133 1bdd drivers/staging/fbtft/fb_hx8340bn.o
5444 1264 0 6708 1a34 drivers/staging/fbtft/fb_hx8347d.o
3581 1360 0 4941 134d drivers/staging/fbtft/fb_ili9163.o
7154 1552 0 8706 2202 drivers/staging/fbtft/fb_ili9320.o
7478 2544 0 10022 2726 drivers/staging/fbtft/fb_ili9325.o
6327 1424 0 7751 1e47 drivers/staging/fbtft/fb_s6d1121.o
6498 1776 0 8274 2052 drivers/staging/fbtft/fb_ssd1289.o
After:
text data bss dec hex filename
5376 1584 64 7024 1b70 drivers/staging/fbtft/fb_hx8340bn.o
5276 1328 0 6604 19cc drivers/staging/fbtft/fb_hx8347d.o
3581 1360 0 4941 134d drivers/staging/fbtft/fb_ili9163.o
6905 1616 0 8521 2149 drivers/staging/fbtft/fb_ili9320.o
7229 2608 0 9837 266d drivers/staging/fbtft/fb_ili9325.o
6030 1488 0 7518 1d5e drivers/staging/fbtft/fb_s6d1121.o
6249 1872 0 8121 1fb9 drivers/staging/fbtft/fb_ssd1289.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906153052.31846-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Don't populate two arrays on the stack but instead make them
static const. Makes the object code smaller by 49 bytes.
Before:
text data bss dec hex filename
26821 5616 0 32437 7eb5 rtl8188eu/core/rtw_ieee80211.o
After:
text data bss dec hex filename
26612 5776 0 32388 7e84 rtl8188eu/core/rtw_ieee80211.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Link: https://lore.kernel.org/r/20190906173949.21860-1-colin.king@canonical.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove unused macro IS_MAC_ADDRESS_BROADCAST. In future if one wants use
it ,use generic API "is_broadcast_ether_addr"
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Link: https://lore.kernel.org/r/1567933780-2790-1-git-send-email-hariprasad.kelam@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The devicetree bindings for anybus-controller were mistakenly
merged into the main Linux tree. Its driver resides in
staging/, so the bindings belong in staging/ too.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Fixes: 20a980e957bf ("dt-bindings: anybus-controller: document devicetree binding")
Signed-off-by: Sven Van Asbroeck <TheSven73@gmail.com>
Link: https://lore.kernel.org/r/20190908134805.30957-1-TheSven73@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As the function argument and variables are defined as type 'bool',
remove local TRUE/FALSE define and change usage of those macros
with boolean value.
Signed-off-by: Saiyam Doshi <saiyamdoshi.in@gmail.com>
Link: https://lore.kernel.org/r/20190908175247.GA20699@SD
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If rtc_clk is provided from DT, use it and enable it.
This is optional.
The signal may be hardcoded and no need to be requested,
but if DT provides it, use it.
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Ajay Singh <ajay.kathat@microchip.com>
Link: https://lore.kernel.org/r/1568037993-4646-2-git-send-email-eugen.hristev@microchip.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
