Age | Commit message (Collapse) | Author |
|
The newly added suspend/resume functions are only used if CONFIG_PM
is enabled:
drivers/mfd/rk808.c:752:12: error: 'rk8xx_resume' defined but not used [-Werror=unused-function]
drivers/mfd/rk808.c:732:12: error: 'rk8xx_suspend' defined but not used [-Werror=unused-function]
Mark them as __maybe_unused so the compiler can silently drop them
when they are not needed.
Fixes: 586c1b4125b3 ("mfd: rk808: Add RK817 and RK809 support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The documentation for Marvell's cp110 phy refers to these
registers/register regions as DTL control, DTL frequency loop enable,
etc. This patch aligns the relevant code for these accordingly.
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Marvell's cp110 phy supports RXAUI on lanes 2, 3, 4, and 5 when
connected to port zero. When used in this mode, lanes operate in pairs
of two (2 and 3, 4 and 5).
Signed-off-by: Matt Pelland <mpelland@starry.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Armada CP110 PCIe controller can have from one to four PHYs for
configuring SERDES lanes (PCIe x1, PCIe x2 or PCIe x4). Describe the
phys and phy-names properties in the bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Marvell CP110 COMPHY block is fed by 3 clocks. Describe each of them in the
bindings.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Now that all COMPHY modes are supported by the driver, update the
comment stating that mvebu_comphy_power_off() should be called for
each lane. This is still wrong because for compatibility reasons, it
might break users running an old firmware (the driver only uses SMC
calls for SATA, USB and PCIe configuration, there is no code in Linux
to fallback on in these cases.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add PCIe support by filling the COMPHY modes table.
Also add a new macro to generate the right value for the firmware
depending on the width (PCI x1, x2, x4, etc). The width will be passed
by the core as the "submode" argument of the ->set_mode() callback. If
this argument is zero, default to x1 mode.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before adding more logic, simplify a bit the writing of the
mvebu_comphy_get_mode() helper by using a pointer instead of
referencing a configuration with the entire table name.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add the corresponding entries in the COMPHY modes table.
SATA support does not need any additional care.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add USB3 host/device support by adding the right entries in the COMPHY
modes table. A new macro is created to instantiate a "generic" mode
ie. not an Ethernet one. This macro will be re-used when adding SATA
support.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The COMPHY can configure the SERDES lanes in several non-Ethernet
modes: SATA, USB3, PCIe. Drop the condition limiting the driver to
Ethernet modes only before adding support for more.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Before adding support for other PHY modes (not Ethernet ones), let's
rename the MVEBU_COMPHY_CONF macro to a more specific (and shorter)
appellation.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Add support for RXAUI mode by adding an entry in the COMPHY modes list.
There is no user for this mode yet so we can enforce an up-to-date
firmware and return an error otherwise without breaking anywone.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Currently, the driver supports setting lanes to 1000BASEX, 2500BASEX,
10GKR. Complete the COMPHY modes list by adding two (already
supported) cases for lane 4.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Keep the exact same list of supported configurations but first try to
use the firmware's implementation. If it fails, try the legacy method:
Linux implementation.
Signed-off-by: Grzegorz Jaszczyk <jaz@semihalf.com>
[miquel.raynal@bootlin.com: adapt the content to the mainline driver]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Explicitly set the lane submode (enum) to a known invalid value.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
There is no public clock tree that implies such dependencies between
the MG/MG-core/AXI clocks and the COMPHY IP but accessing the COMPHY
registers while one of the three clocks are disabled stalls the CPU.
This happens if, for instance, the COMPHY driver probe is deferred
(eg. the USB Vbus regulator driver is not yet visible). The MVPP2
driver which also needs these clocks (among others) will
prepare/enable the clocks, then be deferred, and disable/unprepare
them. Next COMPHY lane to be configured would produce an infinite
stall.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Grzegorz Jaszczyk <jaz@semihalf.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
After commit "linux/bits.h: Add compile time sanity check of GENMASK
inputs" [1], arm64 defconfig builds started failing:
In file included from ../include/linux/bits.h:22,
from ../include/linux/bitops.h:5,
from ../include/linux/kernel.h:12,
from ../include/linux/clk.h:13,
from ../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:9:
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c: In function 'inno_hdmi_phy_rk3328_power_on':
../include/linux/build_bug.h:16:45: error: negative width in bit-field '<anonymous>'
16 | #define BUILD_BUG_ON_ZERO(e) (sizeof(struct { int:(-!!(e)); }))
| ^
../include/linux/bits.h:24:18: note: in expansion of macro 'BUILD_BUG_ON_ZERO'
24 | ((unsigned long)BUILD_BUG_ON_ZERO(__builtin_choose_expr( \
| ^~~~~~~~~~~~~~~~~
../include/linux/bits.h:39:3: note: in expansion of macro 'GENMASK_INPUT_CHECK'
39 | (GENMASK_INPUT_CHECK(high, low) + __GENMASK(high, low))
| ^~~~~~~~~~~~~~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:24:42: note: in expansion of macro 'GENMASK'
24 | #define UPDATE(x, h, l) (((x) << (l)) & GENMASK((h), (l)))
| ^~~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:201:50: note: in expansion of macro 'UPDATE'
201 | #define RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(x) UPDATE(x, 7, 9)
| ^~~~~~
../drivers/phy/rockchip/phy-rockchip-inno-hdmi.c:1046:26: note: in expansion of macro 'RK3328_TERM_RESISTOR_CALIB_SPEED_7_0'
1046 | inno_write(inno, 0xc6, RK3328_TERM_RESISTOR_CALIB_SPEED_7_0(v));
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
As pointed out by Robin and Guenter, inno_write's val argument is an
8-bit value so having a mask larger than that doesn't make sense. This
also matches the rest of the *_7_0 macros in this driver.
[1]: https://lore.kernel.org/lkml/20190801230358.4193-2-rikard.falkeborn@gmail.com/
Reported-by: Andrzej Hajda <a.hajda@samsung.com>
Reported-by: Guenter Roeck <linux@roeck-us.net>
Reported-by: kernelci.org bot <bot@kernelci.org>
Reported-by: Naresh Kamboju <naresh.kamboju@linaro.org>
Suggested-by: Guenter Roeck <linux@roeck-us.net>
Suggested-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
Tested-by: Heiko Stuebner <heiko@sntech.de>
|
|
H_PUT_TCE_INDIRECT handlers receive a page with up to 512 TCEs from
a guest. Although we verify correctness of TCEs before we do anything
with the existing tables, there is a small window when a check in
kvmppc_tce_validate might pass and right after that the guest alters
the page of TCEs, causing an early exit from the handler and leaving
srcu_read_lock(&vcpu->kvm->srcu) (virtual mode) or lock_rmap(rmap)
(real mode) locked.
This fixes the bug by jumping to the common exit code with an appropriate
unlock.
Cc: stable@vger.kernel.org # v4.11+
Fixes: 121f80ba68f1 ("KVM: PPC: VFIO: Add in-kernel acceleration for VFIO")
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
For the 40.46 SMU release, they changed CurrSocketPower to
AverageSocketPower, but this was changed back in 40.47 so just check if
it's 40.46 and make the appropriate change
Tested with 40.45, 40.46 and 40.47 successfully
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The SMU changed reading from CurrSocketPower to AverageSocketPower, so
reflect this accordingly. This fixes the issue where Average Power
Consumption was being reported as 0 from SMU 40.46-onward
v2: Fixed headline prefix
v3: Add check for SMU version for proper compatibility
v4: Style fix
Signed-off-by: Kent Russell <kent.russell@amd.com>
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Since BPF constant blinding is performed after the verifier pass, the
ALU32 instructions inserted for doubleword immediate loads don't have a
corresponding zext instruction. This is causing a kernel oops on powerpc
and can be reproduced by running 'test_cgroup_storage' with
bpf_jit_harden=2.
Fix this by emitting BPF_ZEXT during constant blinding if
prog->aux->verifier_zext is set.
Fixes: a4b1d3c1ddf6cb ("bpf: verifier: insert zero extension according to analysis result")
Reported-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Naveen N. Rao <naveen.n.rao@linux.vnet.ibm.com>
Reviewed-by: Jiong Wang <jiong.wang@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
NFP is using Local Memory to model stack. LM_addr could be used as base of
a 16 32-bit word region of Local Memory. Then, if the stack offset is
beyond the current region, the local index needs to be updated. The update
needs at least three cycles to take effect, therefore the sequence normally
looks like:
local_csr_wr[ActLMAddr3, gprB_5]
nop
nop
nop
If the local index switch happens on a narrow loads, then the instruction
preparing value to zero high 32-bit of the destination register could be
counted as one cycle, the sequence then could be something like:
local_csr_wr[ActLMAddr3, gprB_5]
nop
nop
immed[gprB_5, 0]
However, we have zero extension optimization that zeroing high 32-bit could
be eliminated, therefore above IMMED insn won't be available for which case
the first sequence needs to be generated.
Fixes: 0b4de1ff19bf ("nfp: bpf: eliminate zero extension code-gen")
Signed-off-by: Jiong Wang <jiong.wang@netronome.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
|
|
We need to grab a reference to the fence we wait for.
Signed-off-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Chunming Zhou <david1.zhou@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
If writepage()/writepages() saw an error, but handled it without
reporting it, we should not be re-reporting that error on exit.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If the client attempts to read a page, but the read fails due to some
spurious error (e.g. an ACCESS error or a timeout, ...) then we need
to allow other processes to retry.
Also try to report errors correctly when doing a synchronous readpage.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If the mount is hard, we should ignore the 'io_maxretrans' module
parameter so that we always keep retrying.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If the connection breaks while we're waiting for a reply from the
server, then we want to immediately try to reconnect.
Fixes: ec6017d90359 ("SUNRPC fix regression in umount of a secure mount")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
This reverts commit a79f194aa4879e9baad118c3f8bb2ca24dbef765.
The mechanism for aborting I/O is racy, since we are not guaranteed that
the request is asleep while we're changing both task->tk_status and
task->tk_action.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v5.1
|
|
If a connect or bind attempt returns EADDRINUSE, that means we want to
retry with a different port. It is not a fatal connection error.
Similarly, ENOBUFS is not fatal, but just indicates a memory allocation
issue. Retry after a short delay.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
The pNFS/flexfiles I/O requests are sent with the SOFTCONN flag set, so
they automatically time out if the connection breaks. It should
therefore not be necessary to have the soft flag set in addition.
Fixes: 5f01d9539496 ("nfs41: create NFSv3 DS connection if specified")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
Don't handle errors in call_bind_status()/call_connect_status()
if it turns out that a previous call caused it to succeed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Cc: stable@vger.kernel.org # v5.1+
|
|
Although APIC initialization will typically clear out the LDR before
setting it, the APIC cleanup code should reset the LDR.
This was discovered with a 32-bit KVM guest jumping into a kdump
kernel. The stale bits in the LDR triggered a bug in the KVM APIC
implementation which caused the destination mapping for VCPUs to be
corrupted.
Note that this isn't intended to paper over the KVM APIC bug. The kernel
has to clear the LDR when resetting the APIC registers except when X2APIC
is enabled.
This lacks a Fixes tag because missing to clear LDR goes way back into pre
git history.
[ tglx: Made x2apic_enabled a function call as required ]
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190826101513.5080-3-bsd@redhat.com
|
|
Legacy apic init uses bigsmp for smp systems with 8 and more CPUs. The
bigsmp APIC implementation uses physical destination mode, but it
nevertheless initializes LDR and DFR. The LDR even ends up incorrectly with
multiple bit being set.
This does not cause a functional problem because LDR and DFR are ignored
when physical destination mode is active, but it triggered a problem on a
32-bit KVM guest which jumps into a kdump kernel.
The multiple bits set unearthed a bug in the KVM APIC implementation. The
code which creates the logical destination map for VCPUs ignores the
disabled state of the APIC and ends up overwriting an existing valid entry
and as a result, APIC calibration hangs in the guest during kdump
initialization.
Remove the bogus LDR/DFR initialization.
This is not intended to work around the KVM APIC bug. The LDR/DFR
ininitalization is wrong on its own.
The issue goes back into the pre git history. The fixes tag is the commit
in the bitkeeper import which introduced bigsmp support in 2003.
git://git.kernel.org/pub/scm/linux/kernel/git/tglx/history.git
Fixes: db7b9e9f26b8 ("[PATCH] Clustered APIC setup for >8 CPU systems")
Suggested-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Bandan Das <bsd@redhat.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190826101513.5080-2-bsd@redhat.com
|
|
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This updates the documentation for supporting an optional extra interrupt
cell to specify edge vs level triggered.
Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
* Some lines exceeded 80 characters.
* Clarified statement about AUX register interface
Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
This adds support for an optional extra interrupt cell to specify edge
vs level triggered. It is backward compatible with dts files with only
one cell, and will default to level-triggered in such a case.
Note that I had to make a change to idu_irq_set_affinity as well, as
this function was setting the interrupt type to "level" unconditionally,
since this was the only type supported previously.
Signed-off-by: Mischa Jonker <mischa.jonker@synopsys.com>
Reviewed-by: Vineet Gupta <vgupta@synopsys.com>
Signed-off-by: Vineet Gupta <vgupta@synopsys.com>
|
|
When userspace application calls ioctl(2) to configure hardware for PCM
playback substream, ALSA OXFW driver handles incoming AMDTP stream.
In this case, outgoing AMDTP stream should be handled.
This commit fixes the bug for v5.3-rc kernel.
Fixes: 4f380d007052 ("ALSA: oxfw: configure packet format in pcm.hw_params callback")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
32-bit processes running on a 64-bit kernel are not always detected
correctly, causing the process to crash when uretprobes are installed.
The reason for the crash is that in_ia32_syscall() is used to determine the
process's mode, which only works correctly when called from a syscall.
In the case of uretprobes, however, the function is called from a exception
and always returns 'false' on a 64-bit kernel. In consequence this leads to
corruption of the process's return address.
Fix this by using user_64bit_mode() instead of in_ia32_syscall(), which
is correct in any situation.
[ tglx: Add a comment and the following historical info ]
This should have been detected by the rename which happened in commit
abfb9498ee13 ("x86/entry: Rename is_{ia32,x32}_task() to in_{ia32,x32}_syscall()")
which states in the changelog:
The is_ia32_task()/is_x32_task() function names are a big misnomer: they
suggests that the compat-ness of a system call is a task property, which
is not true, the compatness of a system call purely depends on how it
was invoked through the system call layer.
.....
and then it went and blindly renamed every call site.
Sadly enough this was already mentioned here:
8faaed1b9f50 ("uprobes/x86: Introduce sizeof_long(), cleanup adjust_ret_addr() and
arch_uretprobe_hijack_return_addr()")
where the changelog says:
TODO: is_ia32_task() is not what we actually want, TS_COMPAT does
not necessarily mean 32bit. Fortunately syscall-like insns can't be
probed so it actually works, but it would be better to rename and
use is_ia32_frame().
and goes all the way back to:
0326f5a94dde ("uprobes/core: Handle breakpoint and singlestep exceptions")
Oh well. 7+ years until someone actually tried a uretprobe on a 32bit
process on a 64bit kernel....
Fixes: 0326f5a94dde ("uprobes/core: Handle breakpoint and singlestep exceptions")
Signed-off-by: Sebastian Mayr <me@sam.st>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Dmitry Safonov <dsafonov@virtuozzo.com>
Cc: Oleg Nesterov <oleg@redhat.com>
Cc: Srikar Dronamraju <srikar@linux.vnet.ibm.com>
Cc: stable@vger.kernel.org
Link: https://lkml.kernel.org/r/20190728152617.7308-1-me@sam.st
|
|
Despite extensive testing of commit 885bd765963b ("phy: qcom-qmp: Correct
READY_STATUS poll break condition") I failed to conclude that the
PHYSTATUS bit of the PCS_STATUS register used in PCIe and USB3 falls as
the PHY gets ready. Similar to the prior bug with UFS the code will
generally get past the check before the transition and thereby
"succeed".
Correct the name of the register used PCIe and USB3 PHYs, replace
mask_pcs_ready with a constant expression depending on the type of the
PHY and check for the appropriate ready state.
Cc: stable@vger.kernel.org
Cc: Vivek Gautam <vivek.gautam@codeaurora.org>
Cc: Evan Green <evgreen@chromium.org>
Cc: Niklas Cassel <niklas.cassel@linaro.org>
Reported-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Fixes: 885bd765963b ("phy: qcom-qmp: Correct READY_STATUS poll break condition")
Signed-off-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Tested-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Each iteration of for_each_available_child_of_node() puts the previous
node, but in the case of a return from the middle of the loop, there is
no put, thus causing a memory leak. Hence create a new label,
err_node_put, that puts the previous node (child) before returning the
required value. Also include the statement pm_runtime_disable() under
this label in order to avoid repetition among mid-loop return
conditions. Edit the mid-loop return statements to instead go to this
new label err_node_put.
Issue found with Coccinelle.
Signed-off-by: Nishka Dasgupta <nishkadg.linux@gmail.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The hardware manual should be revised, but the initial value of
VBCTRL.OCCLREN is set to 1 actually. If the bit is set, the hardware
clears VBCTRL.VBOUT and ADPCTRL.DRVVBUS registers automatically
when the hardware detects over-current signal from a USB power switch.
However, since the hardware doesn't have any registers which
indicates over-current, the driver cannot handle it at all. So, if
"is_otg_channel" hardware detects over-current, since ADPCTRL.DRVVBUS
register is cleared automatically, the channel cannot be used after
that.
To resolve this behavior, this patch sets the VBCTRL.OCCLREN to 0
to keep ADPCTRL.DRVVBUS even if the "is_otg_channel" hardware
detects over-current. (We assume a USB power switch itself protects
over-current and turns the VBUS off.)
This patch is inspired by a BSP patch from Kazuya Mizuguchi.
Fixes: 1114e2d31731 ("phy: rcar-gen3-usb2: change the mode to OTG on the combined channel")
Cc: <stable@vger.kernel.org> # v4.5+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
The regmap_node variable is still being used in the syscon_node_to_regmap()
call after the of_node_put() call, which may result in use-after-free.
Fixes: 71e2f5c5c224 ("phy: ti: Add a new SERDES driver for TI's AM654x SoC")
Signed-off-by: Wen Yang <wen.yang99@zte.com.cn>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Reviewed-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
Rahul Tanwar reported the following bug on DT systems:
> 'ioapic_dynirq_base' contains the virtual IRQ base number. Presently, it is
> updated to the end of hardware IRQ numbers but this is done only when IOAPIC
> configuration type is IOAPIC_DOMAIN_LEGACY or IOAPIC_DOMAIN_STRICT. There is
> a third type IOAPIC_DOMAIN_DYNAMIC which applies when IOAPIC configuration
> comes from devicetree.
>
> See dtb_add_ioapic() in arch/x86/kernel/devicetree.c
>
> In case of IOAPIC_DOMAIN_DYNAMIC (DT/OF based system), 'ioapic_dynirq_base'
> remains to zero initialized value. This means that for OF based systems,
> virtual IRQ base will get set to zero.
Such systems will very likely not even boot.
For DT enabled machines ioapic_dynirq_base is irrelevant and not
updated, so simply map the IRQ base 1:1 instead.
Reported-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Tested-by: Rahul Tanwar <rahul.tanwar@linux.intel.com>
Tested-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: alan@linux.intel.com
Cc: bp@alien8.de
Cc: cheol.yong.kim@intel.com
Cc: qi-ming.wu@intel.com
Cc: rahul.tanwar@intel.com
Cc: rppt@linux.ibm.com
Cc: tony.luck@intel.com
Link: http://lkml.kernel.org/r/20190821081330.1187-1-rahul.tanwar@linux.intel.com
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
Ice Lake Thunderbolt controller includes two new device property
compatible properties that we need to be able to extract in the driver
so add them to the growing array of GUIDs.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The Thunderbolt controller is integrated into the Ice Lake CPU itself
and requires special flows to power it on and off using force power bit
in NHI VSEC registers. Runtime PM (RTD3) and Sx flows also differ from
the discrete solutions. Now the firmware notifies the driver whether
RTD3 entry or exit are possible. The driver is responsible of sending
Go2Sx command through link controller mailbox when system enters Sx
states (suspend-to-mem/disk). Rest of the ICM firwmare flows follow
Titan Ridge.
Signed-off-by: Raanan Avargil <raanan.avargil@intel.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|
|
Ice Lake Thunderbolt controller NVM firmware is part of the BIOS image
which means it is not writable through the DMA port anymore. However, we
can still read it so we can keep nvm_version and active parts of NVM.
This way users still can find out the active NVM version and other
potentially useful information directly from Linux.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|
|
Thunderbolt host routers may not always contain DROM that includes
device identification information. This is mostly needed for Ice Lake
systems but some Falcon Ridge controllers on PCs also do not have DROM.
In that case hide the identification attributes.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|
|
There are two ways to mark a port as unimplemented. Typical way is to
return port type as TB_TYPE_INACTIVE when its config space is read.
Alternatively if the port is not physically present (such as ports 10
and 11 in ICL) reading from port config space returns
TB_CFG_ERROR_INVALID_CONFIG_SPACE instead. Currently the driver bails
out from adding the switch if it receives any error during port
inititialization which is wrong.
Handle this properly and just leave the port as TB_TYPE_INACTIVE before
continuing to the next port.
This also allows us to get rid of special casing for Light Ridge port 5
in eeprom.c.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Yehezkel Bernat <YehezkelShB@gmail.com>
Tested-by: Mario Limonciello <mario.limonciello@dell.com>
|