| Age | Commit message (Collapse) | Author |
|---|
|
Add format version of Wi-Fi firmware commands/events for firmware
version 0.29.122.0.
Signed-off-by: Ching-Te Ku <ku920601@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250308025832.10400-2-pkshih@realtek.com
|
|
Some of 11ax AP set the UL HE-SIG-A2 reserved subfield to all 0s, which
will cause the 11be chip to recognize trigger frame as EHT. We propose
a method to bypass the "UL HE-SIG-A2 reserved subfield" and always uses
HE TB in response to the AP's trigger frame.
Signed-off-by: Dian-Syuan Yang <dian_syuan0116@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-6-pkshih@realtek.com
|
|
The 8922A now supports dynamic antenna gain. However, in firmware
before v0.35.64.0, different transmit powers cannot be applied to
each RF path. To comply with regulatory limits in these older
firmware, the lower of the two requested transmit powers will
be used for both paths when they differ.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-5-pkshih@realtek.com
|
|
The dynamic antenna gain (DAG) considers the country, meaning DAG can
be activated only when countries and regulatory domains allow it.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-4-pkshih@realtek.com
|
|
TAS state switching mechanism now incorporates the TX ratio as a
decision parameter. The average power calculation has been improved
by using a higher resolution conversion from dBm to linear. During
scan or MCC operations, TAS state is forced to static SAR and
suspend the average power calculation. Additionally, TAS window
size depends on the regulatory domain and band to ensure compliance.
TAS is enabled when permitted by the regulatory domain and is
currently supported on the 8852CE.
For debugging, add a flag to disable_dm that can stop TAS mechanism.
Co-developed-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Zong-Zhe Yang <kevin_yang@realtek.com>
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-3-pkshih@realtek.com
|
|
Enhanced the dBm to linear conversion function to accommodate negative
dBm values and improved the precision from 1 dBm to 0.25 dBm.
Signed-off-by: Kuan-Chung Chen <damon.chen@realtek.com>
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Link: https://patch.msgid.link/20250306021144.12854-2-pkshih@realtek.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext
Pull sched_ext fix from Tejun Heo:
"BPF schedulers could trigger a crash by passing in an invalid CPU to
the scx_bpf_select_cpu_dfl() helper.
Fix it by verifying input validity"
* tag 'sched_ext-for-6.14-rc6-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/sched_ext:
sched_ext: Validate prev_cpu in scx_bpf_select_cpu_dfl()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi
Pull spi fixes from Mark Brown:
"A couple of driver specific fixes, an error handling fix for the Atmel
QuadSPI driver and a fix for a nasty synchronisation issue in the data
path for the Microchip driver which affects larger transfers.
There's also a MAINTAINERS update for the Samsung driver"
* tag 'spi-fix-v6.14-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/broonie/spi:
spi: microchip-core: prevent RX overflows when transmit size > FIFO size
MAINTAINERS: add tambarus as R for Samsung SPI
spi: atmel-quadspi: remove references to runtime PM on error path
|
|
Don't error out on large MTU if XDP is multi-buf.
The ping test now tests ping with XDP and high MTU.
netdevsim doesn't actually run the prog (yet?) so
it doesn't matter if the prog was multi-buf..
Reviewed-by: Michal Kubiak <michal.kubiak@intel.com>
Link: https://patch.msgid.link/20250311092820.542148-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stanislav Fomichev says:
====================
net: remove rtnl_lock from the callers of queue APIs
All drivers that use queue management APIs already depend on the netdev
lock. Ultimately, we want to have most of the paths that work with
specific netdev to be rtnl_lock-free (ethtool mostly in particular).
Queue API currently has a much smaller API surface, so start with
rtnl_lock from it:
- add mutex to each dmabuf binding (to replace rtnl_lock)
- move netdev lock management to the callers of netdev_rx_queue_restart
and drop rtnl_lock
====================
Link: https://patch.msgid.link/20250311144026.4154277-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All drivers that use queue API are already converted to use
netdev instance lock. Move netdev instance lock management to
the netlink layer and drop rtnl_lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry. <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-4-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As we move away from rtnl_lock for queue ops, introduce
per-netdev_nl_sock lock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
No functional changes. Next patches will add more granular locking
to netdev_nl_sock.
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reviewed-by: Mina Almasry <almasrymina@google.com>
Link: https://patch.msgid.link/20250311144026.4154277-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Although it does not seem to have any untoward side-effects,
the use of ';' to separate to assignments seems more appropriate than ','.
Flagged by clang-19 -Wcomma
No functional change intended.
Compile tested only.
Signed-off-by: Simon Horman <horms@kernel.org>
Reviewed-by: Michal Swiatkowski <michal.swiatkowski@linux.intel.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://patch.msgid.link/20250307-mlx5-comma-v1-1-934deb6927bb@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Commit 51bef03e1a71 ("selftests/net: deflake GRO tests") recently
switched to NAPI suspension, and lowered the timeout from 1ms to 100us.
This started causing flakes in netdev-run CI. Let's bump it to 200us.
In a quick test of a debug kernel I see failures with 100us, with 200us
in 5 runs I see 2 completely clean runs and 3 with a single retry
(GRO test will retry up to 5 times).
Reviewed-by: Kevin Krakauer <krakauer@google.com>
Link: https://patch.msgid.link/20250310110821.385621-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_dl_reload_up is completely missing instance lock management
which can result in `devlink dev reload` leaving with instance
lock held. Add the missing calls.
Also add netdev_assert_locked to make it clear that the up() method
is running with the instance lock grabbed.
v2:
- add net/netdev_lock.h include to bnxt_devlink.c for netdev_assert_locked
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-3-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
netdev_lock_ops conditionally grabs instance lock when queue_mgmt_ops
is defined. However queue_mgmt_ops support is signaled via FW
so we can sometimes boot without queue_mgmt_ops being set.
This will result in bnxt running without instance lock which
the driver now heavily depends on. Set request_ops_lock to true
unconditionally to always request netdev instance lock.
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-2-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
All (error) paths that call dev_close are already holding instance lock,
so switch to netif_close to avoid the deadlock.
v2:
- add missing EXPORT_MODULE for netif_close
Fixes: 004b5008016a ("eth: bnxt: remove most dependencies on RTNL")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Link: https://patch.msgid.link/20250309215851.2003708-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is a couple of places from which we can arrive to ndo_setup_tc
with TC_SETUP_BLOCK/TC_SETUP_FT:
- netlink
- netlink notifier
- netdev notifier
Locking netdev too deep in this call chain seems to be problematic
(especially assuming some/all of the call_netdevice_notifiers
NETDEV_UNREGISTER) might soon be running with the instance lock).
Revert to lockless ndo_setup_tc for TC_SETUP_BLOCK/TC_SETUP_FT. NFT
framework already takes care of most of the locking. Document
the assumptions.
ndo_setup_tc TC_SETUP_BLOCK
nft_block_offload_cmd
nft_chain_offload_cmd
nft_flow_block_chain
nft_flow_offload_chain
nft_flow_rule_offload_abort
nft_flow_rule_offload_commit
nft_flow_rule_offload_commit
nf_tables_commit
nfnetlink_rcv_batch
nfnetlink_rcv_skb_batch
nfnetlink_rcv
nft_offload_netdev_event
NETDEV_UNREGISTER notifier
ndo_setup_tc TC_SETUP_FT
nf_flow_table_offload_cmd
nf_flow_table_offload_setup
nft_unregister_flowtable_hook
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
nft_flowtable_update
nf_tables_newflowtable
nft_flowtable_event
nf_tables_flowtable_event
NETDEV_UNREGISTER notifier
__nft_unregister_flowtable_net_hooks
nft_unregister_flowtable_net_hooks
nf_tables_commit
nfnetlink_rcv_batch (.call NFNL_CB_BATCH)
__nf_tables_abort
nf_tables_abort
nfnetlink_rcv_batch
__nft_release_hook
__nft_release_hooks
nf_tables_pre_exit_net -> module unload
nft_rcv_nl_event
netlink_register_notifier (oh boy)
nft_register_flowtable_net_hooks
nft_flowtable_update
nf_tables_newflowtable
nf_tables_newflowtable
Fixes: c4f0f30b424e ("net: hold netdev instance lock during nft ndo_setup_tc")
Signed-off-by: Stanislav Fomichev <sdf@fomichev.me>
Reported-by: syzbot+0afb4bcf91e5a1afdcad@syzkaller.appspotmail.com
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250308044726.1193222-1-sdf@fomichev.me
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
nf_conntrack_max and nf_conntrack_expect_max sysctls were authorized to
be written any negative value, which would then be stored in the
unsigned int variables nf_conntrack_max and nf_ct_expect_max variables.
While the do_proc_dointvec_conv function is supposed to limit writing
handled by proc_dointvec proc_handler to INT_MAX. Such a negative value
being written in an unsigned int leads to a very high value, exceeding
this limit.
Moreover, the nf_conntrack_expect_max sysctl documentation specifies the
minimum value is 1.
The proc_handlers have thus been updated to proc_dointvec_minmax in
order to specify the following write bounds :
* Bound nf_conntrack_max sysctl writings between SYSCTL_ZERO
and SYSCTL_INT_MAX.
* Bound nf_conntrack_expect_max sysctl writings between SYSCTL_ONE
and SYSCTL_INT_MAX as defined in the sysctl documentation.
With this patch applied, sysctl writes outside the defined in the bound
will thus lead to a write error :
```
sysctl -w net.netfilter.nf_conntrack_expect_max=-1
sysctl: setting key "net.netfilter.nf_conntrack_expect_max": Invalid argument
```
Signed-off-by: Nicolas Bouchinet <nicolas.bouchinet@ssi.gouv.fr>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Cong Wang says:
====================
net_sched: Prevent creation of classes with TC_H_ROOT
This patchset contains a bug fix and its TDC test case.
====================
Link: https://patch.msgid.link/20250306232355.93864-1-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Integrate the reproduer from Mingi to TDC.
All test results:
1..4
ok 1 0385 - Create DRR with default setting
ok 2 2375 - Delete DRR with handle
ok 3 3092 - Show DRR class
ok 4 4009 - Reject creation of DRR class with classid TC_H_ROOT
Cc: Mingi Cho <mincho@theori.io>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/20250306232355.93864-3-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function qdisc_tree_reduce_backlog() uses TC_H_ROOT as a termination
condition when traversing up the qdisc tree to update parent backlog
counters. However, if a class is created with classid TC_H_ROOT, the
traversal terminates prematurely at this class instead of reaching the
actual root qdisc, causing parent statistics to be incorrectly maintained.
In case of DRR, this could lead to a crash as reported by Mingi Cho.
Prevent the creation of any Qdisc class with classid TC_H_ROOT
(0xFFFFFFFF) across all qdisc types, as suggested by Jamal.
Reported-by: Mingi Cho <mincho@theori.io>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Fixes: 066a3b5b2346 ("[NET_SCHED] sch_api: fix qdisc_tree_decrease_qlen() loop")
Link: https://patch.msgid.link/20250306232355.93864-2-xiyou.wangcong@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PRT BOs may not have any backing store, so bo->tbo.resource will be
NULL. Check for that before dereferencing.
Fixes: 0cce5f285d9a ("drm/amdkfd: Check correct memory types for is_system variable")
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Natalie Vock <natalie.vock@gmx.de>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 3e3fcd29b505cebed659311337ea03b7698767fc)
Cc: stable@vger.kernel.org # 6.12.x
|
|
[Why]
If reset is detected and kfd need to evict working queues, HWS moving queue will be failed.
Then remaining queues are not evicted and in active state.
After reset done, kfd uses HWS to termination remaining activated queues but HWS is resetted.
So remove queue will be failed again.
[How]
Keep removing all queues even if HWS returns failed.
It will not affect cpsch as it checks reset_domain->sem.
v2: If any queue failed, evict queue returns error.
v3: Declare err inside the if-block.
Reviewed-by: Felix Kuehling <felix.kuehling@amd.com>
Signed-off-by: Yifan Zha <Yifan.Zha@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
(cherry picked from commit 42c854b8fb0cce512534aa2b7141948e80c6ebb0)
Cc: stable@vger.kernel.org
|
|
There is no difference between the sge of READ and non-READ
operations in hns RoCE. Set max_sge_rd to the same value as
max_send_sge.
Fixes: 9a4435375cd1 ("IB/hns: Add driver files for hns RoCE driver")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-8-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Add xa_destroy() for xarray in driver.
Fixes: 5c1f167af112 ("RDMA/hns: Init SRQ table for hip08")
Fixes: 27e19f451089 ("RDMA/hns: Convert cq_table to XArray")
Fixes: 736b5a70db98 ("RDMA/hns: Convert qp_table_tree to XArray")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-7-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
When ib_copy_to_udata() fails in hns_roce_create_qp_common(),
hns_roce_qp_remove() should be called in the error path to
clean up resources in hns_roce_qp_store().
Fixes: 0f00571f9433 ("RDMA/hns: Use new SQ doorbell register for HIP09")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-6-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
SQ params from userspace are checked in by set_user_sq_size(). But
when the check fails, the function doesn't return but instead keep
running and overwrite 'ret'. As a result, the invalid params will
not get blocked actually.
Add a return right after the failed check. Besides, although the
check result of kernel sq params will not be overwritten, to keep
coding style unified, move default_congest_type() before
set_kernel_sq_size().
Fixes: 6ec429d5887a ("RDMA/hns: Support userspace configuring congestion control algorithm with QP granularity")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-5-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Currently the condition of unmapping sdb in error path is not exactly
the same as the condition of mapping in alloc_user_qp_db(). This may
cause a problem of unmapping an unmapped db in some case, such as
when the QP is XRC TGT. Unified the two conditions.
Fixes: 90ae0b57e4a5 ("RDMA/hns: Combine enable flags of qp")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-4-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Driver runs a for-loop when allocating bt pages and mapping them with
buffer pages. When a large buffer (e.g. MR over 100GB) is being allocated,
it may require a considerable loop count. This will lead to soft lockup:
watchdog: BUG: soft lockup - CPU#27 stuck for 22s!
...
Call trace:
hem_list_alloc_mid_bt+0x124/0x394 [hns_roce_hw_v2]
hns_roce_hem_list_request+0xf8/0x160 [hns_roce_hw_v2]
hns_roce_mtr_create+0x2e4/0x360 [hns_roce_hw_v2]
alloc_mr_pbl+0xd4/0x17c [hns_roce_hw_v2]
hns_roce_reg_user_mr+0xf8/0x190 [hns_roce_hw_v2]
ib_uverbs_reg_mr+0x118/0x290
watchdog: BUG: soft lockup - CPU#35 stuck for 23s!
...
Call trace:
hns_roce_hem_list_find_mtt+0x7c/0xb0 [hns_roce_hw_v2]
mtr_map_bufs+0xc4/0x204 [hns_roce_hw_v2]
hns_roce_mtr_create+0x31c/0x3c4 [hns_roce_hw_v2]
alloc_mr_pbl+0xb0/0x160 [hns_roce_hw_v2]
hns_roce_reg_user_mr+0x108/0x1c0 [hns_roce_hw_v2]
ib_uverbs_reg_mr+0x120/0x2bc
Add a cond_resched() to fix soft lockup during these loops. In order not
to affect the allocation performance of normal-size buffer, set the loop
count of a 100GB MR as the threshold to call cond_resched().
Fixes: 38389eaa4db1 ("RDMA/hns: Add mtr support for mixed multihop addressing")
Signed-off-by: Junxian Huang <huangjunxian6@hisilicon.com>
Link: https://patch.msgid.link/20250311084857.3803665-3-huangjunxian6@hisilicon.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
Pre-content hooks in page faults introduces potential deadlock of HSM
handler in userspace with filesystem freezing.
The requirement with pre-content event is that for every accessed file
range an event covering at least this range will be generated at least
once before the file data is accesses.
In preparation to disabling pre-content event hooks on page faults,
add pre-content hooks at mmap() variants for the entire mmaped range,
so HSM can fill content when user requests to map a portion of the file.
Note that exec() variant also calls vm_mmap_pgoff() internally to map
code sections, so pre-content hooks are also generated in this case.
Link: https://lore.kernel.org/linux-fsdevel/7ehxrhbvehlrjwvrduoxsao5k3x4aw275patsb3krkwuq573yv@o2hskrfawbnc/
Suggested-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Amir Goldstein <amir73il@gmail.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Link: https://patch.msgid.link/20250312073852.2123409-2-amir73il@gmail.com
|
|
The Altera USB Blaster 3, available as both a cable and an on-board
solution, is primarily used for programming and debugging FPGAs.
It interfaces with host software such as Quartus Programmer,
System Console, SignalTap, and Nios Debugger. The device utilizes
either an FT2232 or FT4232 chip.
Enabling the support for various configurations of the on-board
USB Blaster 3 by including the appropriate VID/PID pairs,
allowing it to function as a serial device via ftdi_sio.
Note that this check-in does not include support for the
cable solution, as it does not support UART functionality.
The supported configurations are determined by the
hardware design and include:
1) PID 0x6022, FT2232, 1 JTAG port (Port A) + Port B as UART
2) PID 0x6025, FT4232, 1 JTAG port (Port A) + Port C as UART
3) PID 0x6026, FT4232, 1 JTAG port (Port A) + Port C, D as UART
4) PID 0x6029, FT4232, 1 JTAG port (Port B) + Port C as UART
5) PID 0x602a, FT4232, 1 JTAG port (Port B) + Port C, D as UART
6) PID 0x602c, FT4232, 1 JTAG port (Port A) + Port B as UART
7) PID 0x602d, FT4232, 1 JTAG port (Port A) + Port B, C as UART
8) PID 0x602e, FT4232, 1 JTAG port (Port A) + Port B, C, D as UART
These configurations allow for flexibility in how the USB Blaster 3 is
used, depending on the specific needs of the hardware design.
Signed-off-by: Boon Khai Ng <boon.khai.ng@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
The custom suspend function causes a build warning when CONFIG_PM_SLEEP
is disabled:
sound/soc/codecs/cs42l43.c:2405:12: error: unused function 'cs42l43_codec_runtime_force_suspend' [-Werror,-Wunused-function]
Change SET_SYSTEM_SLEEP_PM_OPS() to the newer SYSTEM_SLEEP_PM_OPS(),
to avoid this.
Fixes: 164b7dd4546b ("ASoC: cs42l43: Add jack delay debounce after suspend")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Maciej Strozek <mstrozek@opensource.cirrus.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Link: https://patch.msgid.link/20250305172738.3437513-1-arnd@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Commit c780d01cf1a6 ("media: vb2: vb2_core_queue_init(): sanity check lock
and wait_prepare/finish") added a sanity check to ensure that if there are
no wait_prepare/finish callbacks set by the driver, then the vb2_queue lock
must be set, since otherwise the vb2 core cannot do correct locking.
The rtl2832_sdr.c triggered this warning: it turns out that while the
driver does set this lock, it sets it too late. So move it up to before
the vb2_queue_init() call.
Reported-by: Arthur Marsh <arthur.marsh@internode.on.net>
Closes: https://lore.kernel.org/linux-media/20241211042355.8479-1-user@am64/
Fixes: 8fcd2795d22a ("media: rtl2832_sdr: drop vb2_ops_wait_prepare/finish")
Cc: stable@vger.kernel.org
Reviewed-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
|
|
Replace vmalloc allocations with kvmalloc since
kvmalloc is more flexible in memory allocation
Signed-off-by: Denis Kirjanov <kirjanov@gmail.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Add a fixup to enable the mute LED on HP Pavilion x360 Convertible
14-dy1xxx with ALC295 codec. The appropriate coefficient index and bits
were identified through a brute-force method, as detailed in
https://bbs.archlinux.org/viewtopic.php?pid=2079504#p2079504.
Signed-off-by: Navon John Lukose <navonjohnlukose@gmail.com>
Link: https://patch.msgid.link/20250307213319.35507-1-navonjohnlukose@gmail.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The get->num_services variable is an unsigned int which is controlled by
the user. The struct_size() function ensures that the size calculation
does not overflow an unsigned long, however, we are saving the result to
an int so the calculation can overflow.
Both "len" and "get->num_services" come from the user. This check is
just a sanity check to help the user and ensure they are using the API
correctly. An integer overflow here is not a big deal. This has no
security impact.
Save the result from struct_size() type size_t to fix this integer
overflow bug.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Julian Anastasov <ja@ssi.bg>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
These scripts fail if the kernel is tainted which leads to wrong test
failure reports in CI environments when an unrelated test triggers some
splat.
Check taint state at start of script and SKIP if its already dodgy.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
insert_tree()
Since commit b36e4523d4d5 ("netfilter: nf_conncount: fix garbage
collection confirm race"), `cpu` and `jiffies32` were introduced to
the struct nf_conncount_tuple.
The commit made nf_conncount_add() initialize `conn->cpu` and
`conn->jiffies32` when allocating the struct.
In contrast, count_tree() was not changed to initialize them.
By commit 34848d5c896e ("netfilter: nf_conncount: Split insert and
traversal"), count_tree() was split and the relevant allocation
code now resides in insert_tree().
Initialize `conn->cpu` and `conn->jiffies32` in insert_tree().
BUG: KMSAN: uninit-value in find_or_evict net/netfilter/nf_conncount.c:117 [inline]
BUG: KMSAN: uninit-value in __nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143
find_or_evict net/netfilter/nf_conncount.c:117 [inline]
__nf_conncount_add+0xd9c/0x2850 net/netfilter/nf_conncount.c:143
count_tree net/netfilter/nf_conncount.c:438 [inline]
nf_conncount_count+0x82f/0x1e80 net/netfilter/nf_conncount.c:521
connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72
__nft_match_eval net/netfilter/nft_compat.c:403 [inline]
nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433
expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline]
nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288
nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663
NF_HOOK_LIST include/linux/netfilter.h:350 [inline]
ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633
ip_list_rcv+0x9ef/0xa40 net/ipv4/ip_input.c:669
__netif_receive_skb_list_ptype net/core/dev.c:5936 [inline]
__netif_receive_skb_list_core+0x15c5/0x1670 net/core/dev.c:5983
__netif_receive_skb_list net/core/dev.c:6035 [inline]
netif_receive_skb_list_internal+0x1085/0x1700 net/core/dev.c:6126
netif_receive_skb_list+0x5a/0x460 net/core/dev.c:6178
xdp_recv_frames net/bpf/test_run.c:280 [inline]
xdp_test_run_batch net/bpf/test_run.c:361 [inline]
bpf_test_run_xdp_live+0x2e86/0x3480 net/bpf/test_run.c:390
bpf_prog_test_run_xdp+0xf1d/0x1ae0 net/bpf/test_run.c:1316
bpf_prog_test_run+0x5e5/0xa30 kernel/bpf/syscall.c:4407
__sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5813
__do_sys_bpf kernel/bpf/syscall.c:5902 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5900 [inline]
__ia32_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5900
ia32_sys_call+0x394d/0x4180 arch/x86/include/generated/asm/syscalls_32.h:358
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0xb0/0x110 arch/x86/entry/common.c:387
do_fast_syscall_32+0x38/0x80 arch/x86/entry/common.c:412
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:450
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
Uninit was created at:
slab_post_alloc_hook mm/slub.c:4121 [inline]
slab_alloc_node mm/slub.c:4164 [inline]
kmem_cache_alloc_noprof+0x915/0xe10 mm/slub.c:4171
insert_tree net/netfilter/nf_conncount.c:372 [inline]
count_tree net/netfilter/nf_conncount.c:450 [inline]
nf_conncount_count+0x1415/0x1e80 net/netfilter/nf_conncount.c:521
connlimit_mt+0x7f6/0xbd0 net/netfilter/xt_connlimit.c:72
__nft_match_eval net/netfilter/nft_compat.c:403 [inline]
nft_match_eval+0x1a5/0x300 net/netfilter/nft_compat.c:433
expr_call_ops_eval net/netfilter/nf_tables_core.c:240 [inline]
nft_do_chain+0x426/0x2290 net/netfilter/nf_tables_core.c:288
nft_do_chain_ipv4+0x1a5/0x230 net/netfilter/nft_chain_filter.c:23
nf_hook_entry_hookfn include/linux/netfilter.h:154 [inline]
nf_hook_slow+0xf4/0x400 net/netfilter/core.c:626
nf_hook_slow_list+0x24d/0x860 net/netfilter/core.c:663
NF_HOOK_LIST include/linux/netfilter.h:350 [inline]
ip_sublist_rcv+0x17b7/0x17f0 net/ipv4/ip_input.c:633
ip_list_rcv+0x9ef/0xa40 net/ipv4/ip_input.c:669
__netif_receive_skb_list_ptype net/core/dev.c:5936 [inline]
__netif_receive_skb_list_core+0x15c5/0x1670 net/core/dev.c:5983
__netif_receive_skb_list net/core/dev.c:6035 [inline]
netif_receive_skb_list_internal+0x1085/0x1700 net/core/dev.c:6126
netif_receive_skb_list+0x5a/0x460 net/core/dev.c:6178
xdp_recv_frames net/bpf/test_run.c:280 [inline]
xdp_test_run_batch net/bpf/test_run.c:361 [inline]
bpf_test_run_xdp_live+0x2e86/0x3480 net/bpf/test_run.c:390
bpf_prog_test_run_xdp+0xf1d/0x1ae0 net/bpf/test_run.c:1316
bpf_prog_test_run+0x5e5/0xa30 kernel/bpf/syscall.c:4407
__sys_bpf+0x6aa/0xd90 kernel/bpf/syscall.c:5813
__do_sys_bpf kernel/bpf/syscall.c:5902 [inline]
__se_sys_bpf kernel/bpf/syscall.c:5900 [inline]
__ia32_sys_bpf+0xa0/0xe0 kernel/bpf/syscall.c:5900
ia32_sys_call+0x394d/0x4180 arch/x86/include/generated/asm/syscalls_32.h:358
do_syscall_32_irqs_on arch/x86/entry/common.c:165 [inline]
__do_fast_syscall_32+0xb0/0x110 arch/x86/entry/common.c:387
do_fast_syscall_32+0x38/0x80 arch/x86/entry/common.c:412
do_SYSENTER_32+0x1f/0x30 arch/x86/entry/common.c:450
entry_SYSENTER_compat_after_hwframe+0x84/0x8e
Reported-by: syzbot+83fed965338b573115f7@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=83fed965338b573115f7
Fixes: b36e4523d4d5 ("netfilter: nf_conncount: fix garbage collection confirm race")
Signed-off-by: Kohei Enju <enjuk@amazon.com>
Reviewed-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Pablo Neira Ayuso <pablo@netfilter.org>
|
|
Commit 1f47ed294a2b ("block: cleanup and fix batch completion adding
conditions") modified the evaluation criteria for the third argument,
'ioerror', in the blk_mq_add_to_batch() function. Initially, the
function had checked if 'ioerror' equals zero. Following the commit, it
started checking for negative error values, with the presumption that
such values, for instance -EIO, would be passed in.
However, blk_mq_add_to_batch() callers do not pass negative error
values. Instead, they pass status codes defined in various ways:
- NVMe PCI and Apple drivers pass NVMe status code
- virtio_blk driver passes the virtblk request header status byte
- null_blk driver passes blk_status_t
These codes are either zero or positive, therefore the revised check
fails to function as intended. Specifically, with the NVMe PCI driver,
this modification led to the failure of the blktests test case nvme/039.
In this test scenario, errors are artificially injected to the NVMe
driver, resulting in positive NVMe status codes passed to
blk_mq_add_to_batch(), which unexpectedly processes the failed I/O in a
batch. Hence the failure.
To correct the ioerror check within blk_mq_add_to_batch(), make all
callers to uniformly pass the argument as boolean. Modify the callers to
check their specific status codes and pass the boolean value 'is_error'.
Also describe the arguments of blK_mq_add_to_batch as kerneldoc.
Fixes: 1f47ed294a2b ("block: cleanup and fix batch completion adding conditions")
Signed-off-by: Shin'ichiro Kawasaki <shinichiro.kawasaki@wdc.com>
Link: https://lore.kernel.org/r/20250311104359.1767728-3-shinichiro.kawasaki@wdc.com
[axboe: fold in documentation update]
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/wireless/wireless
Johannes berg says:
====================
Few more fixes:
- cfg80211/mac80211
- stop possible runaway wiphy worker
- EHT should not use reserved MPDU size bits
- don't run worker for stopped interfaces
- fix SA Query processing with MLO
- fix lookup of assoc link BSS entries
- correct station flush on unauthorize
- iwlwifi:
- TSO fixes
- fix non-MSI-X platforms
- stop possible runaway restart worker
- rejigger maintainers so I'm not CC'ed on
everything
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver is always clearing the mask that sets the VLAN ID/Service Level
in the adapter. Recent change for supporting multiple traffic class
exposed this issue.
Allow setting SL and VLAN_ID while QP is moved from INIT to RTR state.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Fixes: c64b16a37b6d ("RDMA/bnxt_re: Support different traffic class")
Signed-off-by: Saravanan Vajravel <saravanan.vajravel@broadcom.com>
Signed-off-by: Selvin Xavier <selvin.xavier@broadcom.com>
Link: https://patch.msgid.link/1741670196-2919-1-git-send-email-selvin.xavier@broadcom.com
Signed-off-by: Leon Romanovsky <leon@kernel.org>
|
|
If i2c_add_adapter() fails, the request_region() call in sis630_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/3d607601f2c38e896b10207963c6ab499ca5c307.1741033587.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
|
|
If i2c_add_adapter() fails, the request_region() call in ali15x3_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/9b2090cbcc02659f425188ea05f2e02745c4e67b.1741031878.git.christophe.jaillet@wanadoo.fr
|
|
If i2c_add_adapter() fails, the request_region() call in ali1535_setup()
must be undone by a corresponding release_region() call, as done in the
remove function.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/0daf63d7a2ce74c02e2664ba805bbfadab7d25e5.1741031571.git.christophe.jaillet@wanadoo.fr
|
|
On the GTA04A5 writing a reset command to the gyroscope causes IRQ
storms because NACK IRQs are enabled and therefore triggered but not
acked.
Sending a reset command to the gyroscope by
i2cset 1 0x69 0x14 0xb6
with an additional debug print in the ISR (not the thread) itself
causes
[ 363.353515] i2c i2c-1: ioctl, cmd=0x720, arg=0xbe801b00
[ 363.359039] omap_i2c 48072000.i2c: addr: 0x0069, len: 2, flags: 0x0, stop: 1
[ 363.366180] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x1110)
[ 363.371673] omap_i2c 48072000.i2c: IRQ (ISR = 0x0010)
[ 363.376892] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.382263] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
[ 363.387664] omap_i2c 48072000.i2c: IRQ LL (ISR = 0x0102)
repeating till infinity
[...]
(0x2 = NACK, 0x100 = Bus free, which is not enabled)
Apparently no other IRQ bit gets set, so this stalls.
Do not ignore enabled interrupts and make sure they are acked.
If the NACK IRQ is not needed, it should simply not enabled, but
according to the above log, caring about it is necessary unless
the Bus free IRQ is enabled and handled. The assumption that is
will always come with a ARDY IRQ, which was the idea behind
ignoring it, proves wrong.
It is true for simple reads from an unused address.
To still avoid the i2cdetect trouble which is the reason for
commit c770657bd261 ("i2c: omap: Fix standard mode false ACK readings"),
avoid doing much about NACK in omap_i2c_xfer_data() which is used
by both IRQ mode and polling mode, so also the false detection fix
is extended to polling usage and IRQ storms are avoided.
By changing this, the hardirq handler is not needed anymore to filter
stuff.
The mentioned gyro reset now just causes a -ETIMEDOUT instead of
hanging the system.
Fixes: c770657bd261 ("i2c: omap: Fix standard mode false ACK readings").
CC: stable@kernel.org
Signed-off-by: Andreas Kemnade <andreas@kemnade.info>
Tested-by: Nishanth Menon <nm@ti.com>
Reviewed-by: Aniket Limaye <a-limaye@ti.com>
Signed-off-by: Andi Shyti <andi.shyti@kernel.org>
Link: https://lore.kernel.org/r/20250228140420.379498-1-andreas@kemnade.info
|
|
The error path when atmci_configure_dma() set dma fails in atmci driver
does not correctly disable the clock.
Add the missing clk_disable_unprepare() to the error path for pair with
clk_prepare_enable().
Fixes: 467e081d23e6 ("mmc: atmel-mci: use probe deferring if dma controller is not ready yet")
Signed-off-by: Gu Bowen <gubowen5@huawei.com>
Acked-by: Aubin Constans <aubin.constans@microchip.com>
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20250225022856.3452240-1-gubowen5@huawei.com
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pointers declared with the __free(kfree) attribute need to be initialized
because they will be passed to kfree() on every return path. There are
two return statement before the "cmd" pointer is initialized so this
leads to an uninitialized variable bug.
Fixes: d1e879ec600f ("wifi: iwlwifi: add iwlmld sub-driver")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Acked-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Link: https://patch.msgid.link/f7c17a7f-f173-43bf-bc39-316b8adde349@stanley.mountain
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
This appears to be an oversight back when the state lookup
was converted to RCU, I see no reason why we need to hold the
state lock here.
__xfrm_state_lookup_byaddr already uses xfrm_state_hold_rcu
helper to obtain a reference, so just replace the state
lock with rcu.
Signed-off-by: Florian Westphal <fw@strlen.de>
Signed-off-by: Steffen Klassert <steffen.klassert@secunet.com>
|
