| Age | Commit message (Collapse) | Author |
|---|
|
We only need to call delete_ctrl once, so given that both
keep-alive timeout and any other fatal error can trigger it,
just make sure we only call delete_ctrl once.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Make sure they are not running and we can free the controller
safely.
Signed-off-by: Roy Shterman <roys@lightbitslabs.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
No reason for them to be kept around if we are
deleting the subsystem, so instead of passively
wait for the host to disconnect, actively delete
the controllers.
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Max Gurtovoy <maxg@mellanox.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Correct logic in disconnect queue LS handling.
Rework so that queue searching and error reporting is above the
section to send back a ls rjt
Signed-off-by: James Smart <james.smart@broadcom.com>
Signed-off-by: Sagi Grimberg <sagi@grimberg.me>
|
|
Apparently each GPIO pad's register are 16 bytes, so multiply the pad_map
by that. The same is done in byt_gpio_reg the only other place where
pad_map is used.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Pad retention control after suspend/resume cycle should be done from pin
controller driver instead of PMU (power management unit) driver to avoid
possible ordering and logical dependencies. Till now it worked fine only
because PMU driver registered its sys_ops after pin controller.
This patch adds infrastructure to handle pad retention during pin control
driver resume.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
'enable' parameter has been removed a while ago, so all code for handling
it can be simply removed.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Replace custom code with generic helper.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Exynos5433 support has been added in parallel to adding initconst
annotation to most of the init data structures, so add those
annotations also to Exynos5433 structures.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Do not hide pinctrl drivers for Mediatek platforms using
conditionals. Doing so actually leaves the symbols present (but
always disabled) on all other platforms, which is confusing and
inefficient. Better use real dependencies so that the symbols do not
exist at all on platforms where they are not relevant.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Reported-by: Andreas Färber <afaerber@suse.de>
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/acme/linux into perf/core
Pull the latest perf/core updates from Arnaldo Carvalho de Melo:
New features:
- Introduce 'perf ftrace' a perf front end to the kernel's ftrace
function and function_graph tracer, defaulting to the "function_graph"
tracer, more work will be done in reviving this effort, forward porting
it from its initial patch submission (Namhyung Kim)
- Add 'e' and 'c' hotkeys to expand/collapse call chains for a single
hist entry in the 'perf report' and 'perf top' TUI (Jiri Olsa)
Fixes:
- Fix wrong register name for arm64, used in 'perf probe' (He Kuang)
- Fix map offsets in relocation in libbpf (Joe Stringer)
- Fix looking up dwarf unwind stack info (Matija Glavinic Pecotic)
Infrastructure changes:
- libbpf prog functions sync with what is exported via uapi (Joe Stringer)
Trivial changes:
- Remove unnecessary checks and assignments in 'perf probe's
try_to_find_absolute_address() (Markus Elfring)
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
So that we can suppress the '-t function_graph' and get a more compact command
line:
# perf ftrace usleep 123456 | grep raw_spin_lock | sort -k2 -nr | head -5
2) 0.555 us | _raw_spin_lock();
2) 0.516 us | _raw_spin_lock();
2) 0.410 us | _raw_spin_lock_irq();
2) 0.374 us | _raw_spin_lock_irqsave();
#
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-ss9xgx5htpxcv86x42pnh3m6@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The 'perf ftrace' command is a simple wrapper of kernel's ftrace
functionality. It only supports single thread tracing currently and
just reads trace_pipe in text and then write it to stdout.
Committer notes:
Testing it:
# perf ftrace -f function_graph usleep 123456
<SNIP>
2) | SyS_nanosleep() {
2) | _copy_from_user() {
<SNIP>
2) 0.900 us | }
2) 1.354 us | }
2) | hrtimer_nanosleep() {
2) 0.062 us | __hrtimer_init();
2) | do_nanosleep() {
2) | hrtimer_start_range_ns() {
<SNIP>
2) 5.025 us | }
2) | schedule() {
2) 0.125 us | rcu_note_context_switch();
2) 0.057 us | _raw_spin_lock();
2) | deactivate_task() {
2) 0.369 us | update_rq_clock.part.77();
2) | dequeue_task_fair() {
<SNIP>
2) + 22.453 us | }
2) + 23.736 us | }
2) | pick_next_task_fair() {
<SNIP>
2) + 47.167 us | }
2) | pick_next_task_idle() {
<SNIP>
2) 4.462 us | }
------------------------------------------
2) usleep-20387 => <idle>-0
------------------------------------------
2) 0.806 us | switch_mm_irqs_off();
------------------------------------------
2) <idle>-0 => usleep-20387
------------------------------------------
2) 0.151 us | finish_task_switch();
2) @ 123597.2 us | }
2) 0.037 us | _cond_resched();
2) | hrtimer_try_to_cancel() {
2) 0.064 us | hrtimer_active();
2) 0.353 us | }
2) @ 123605.3 us | }
2) @ 123606.2 us | }
2) @ 123608.3 us | } /* SyS_nanosleep */
2) | __do_page_fault() {
<SNIP>
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>,
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-r1hgmsj4dxny8arn3o9mw512@git.kernel.org
[ Various foward port fixes, add man page ]
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
It's helpful for debugging on tracing features.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>,
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Link: http://lkml.kernel.org/n/tip-rjysr9ljiesymgk4qblteaty@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Current trace info data lacks the saved cmdline mapping which is needed
for pevent to find out the comm of a task. Add this and bump up the
version number so that perf can determine its presence when reading.
This is mostly corresponding to trace.dat file version 6, but still
lacks 4 byte of number of cpus, and 10 bytes of type string - and I
think we don't need those anyway.
Signed-off-by: Namhyung Kim <namhyung@kernel.org>
Tested-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Jeremy Eder <jeder@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>,
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Stephane Eranian <eranian@google.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
[ Change version test from == to >= ]
Link: http://lkml.kernel.org/n/tip-vaooqpxsikxbb3359p0corcb@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Do just like handling other cases i.e. print some debug message and
ignore the sample.
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: David Ahern <dsahern@gmail.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Namhyung Kim <namhyung@kernel.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/n/tip-t7kzlm3cxyvbd7d9n9554ai9@git.kernel.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This function will turn a libbpf pointer into a standard error code (or
0 if the pointer is valid).
This also allows removal of the dependency on linux/err.h in the public
header file, which causes problems in userspace programs built against
libbpf.
Signed-off-by: Joe Stringer <joe@ovn.org>
Acked-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20170123011128.26534-5-joe@ovn.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
These bpf_prog_types were exposed in the uapi but there were no
corresponding functions to set these types for programs in libbpf.
Signed-off-by: Joe Stringer <joe@ovn.org>
Acked-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20170123011128.26534-4-joe@ovn.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Turning this into a macro allows future prog types to be added with a
single line per type.
Signed-off-by: Joe Stringer <joe@ovn.org>
Acked-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: netdev@vger.kernel.org
Link: http://lkml.kernel.org/r/20170123011128.26534-3-joe@ovn.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Commit 4708bbda5cb2 ("tools lib bpf: Fix maps resolution") attempted to
fix map resolution by identifying the number of symbols that point to
maps, and using this number to resolve each of the maps.
However, during relocation the original definition of the map size was
still in use. For up to two maps, the calculation was correct if there
was a small difference in size between the map definition in libbpf and
the one that the client library uses. However if the difference was
large, particularly if more than two maps were used in the BPF program,
the relocation would fail.
For example, when using a map definition with size 28, with three maps,
map relocation would count:
(sym_offset / sizeof(struct bpf_map_def) => map_idx)
(0 / 16 => 0), ie map_idx = 0
(28 / 16 => 1), ie map_idx = 1
(56 / 16 => 3), ie map_idx = 3
So, libbpf reports:
libbpf: bpf relocation: map_idx 3 large than 2
Fix map relocation by checking the exact offset of maps when doing
relocation.
Signed-off-by: Joe Stringer <joe@ovn.org>
[Allow different map size in an object]
Signed-off-by: Wang Nan <wangnan0@huawei.com>
Cc: Alexei Starovoitov <ast@fb.com>
Cc: Daniel Borkmann <daniel@iogearbox.net>
Cc: netdev@vger.kernel.org
Fixes: 4708bbda5cb2 ("tools lib bpf: Fix maps resolution")
Link: http://lkml.kernel.org/r/20170123011128.26534-2-joe@ovn.org
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Remove an error code assignment which is redundant in an if branch for
the handling of a memory allocation failure because the same value was
set for the local variable "err" before.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/0ede09ec-79b6-c8bd-5b20-02c63ed98aab@users.sourceforge.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Remove a condition check which is unnecessary at the end
because this source code place should usually only be reached
with a non-zero pointer.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: He Kuang <hekuang@huawei.com>
Cc: Jiri Olsa <jolsa@kernel.org>
Cc: Milian Wolff <milian.wolff@kdab.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Ravi Bangoria <ravi.bangoria@linux.vnet.ibm.com>
Cc: Wang Nan <wangnan0@huawei.com>
Cc: kernel-janitors@vger.kernel.org
Link: http://lkml.kernel.org/r/a3f2473b-6383-a326-bce0-b826423608b8@users.sourceforge.net
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The register name of arm64 architecture is x0-x31 not r0-r31, this patch
changes this typo.
Before this patch:
# perf probe --definition 'sys_write count'
p:probe/sys_write _text+1502872 count=%r2:s64
# echo 'p:probe/sys_write _text+1502872 count=%r2:s64' > \
/sys/kernel/debug/tracing/kprobe_events
Parse error at argument[0]. (-22)
After this patch:
# perf probe --definition 'sys_write count'
p:probe/sys_write _text+1502872 count=%x2:s64
# echo 'p:probe/sys_write _text+1502872 count=%x2:s64' > \
/sys/kernel/debug/tracing/kprobe_events
# echo 1 >/sys/kernel/debug/tracing/events/probe/enable
# cat /sys/kernel/debug/tracing/trace
...
sh-422 [000] d... 650.495930: sys_write: (SyS_write+0x0/0xc8) count=22
sh-422 [000] d... 651.102389: sys_write: (SyS_write+0x0/0xc8) count=26
sh-422 [000] d... 651.358653: sys_write: (SyS_write+0x0/0xc8) count=86
Signed-off-by: He Kuang <hekuang@huawei.com>
Acked-by: Masami Hiramatsu <mhiramat@kernel.org>
Acked-by: Will Deacon <will.deacon@arm.com>
Cc: Alexander Shishkin <alexander.shishkin@linux.intel.com>
Cc: Bintian Wang <bintian.wang@huawei.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Wang Nan <wangnan0@huawei.com>
Link: http://lkml.kernel.org/r/20170124103015.1936-2-hekuang@huawei.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
This adds support for the pwm_ao_b pin. Unfortunately the registers for
the pwm_ao pins are not documented at all. The source for the pwm_ao_b
pin from this patch is the Khadas VIM GPL kernel source, which sets bit
3 and unsets bits 4 and 31 to enable the PWM LEDs.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Kevin Hilman <khilman@baylibre.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
While we have no users yet rename the platform driver to use the same
pattern as the rest of Intel SoCs, i.e. use full SoC name in
'apollolake-pinctrl'.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
|
|
Currently we already have two pin configuration related callbacks
available for GPIO chips .set_single_ended() and .set_debounce(). In
future we expect to have even more, which does not scale well if we need
to add yet another callback to the GPIO chip structure for each possible
configuration parameter.
Better solution is to reuse what we already have available in the
generic pinconf.
To support this, we introduce a new .set_config() callback for GPIO
chips. The callback takes a single packed pin configuration value as
parameter. This can then be extended easily beyond what is currently
supported by just adding new types to the generic pinconf enum.
If the GPIO driver is backed up by a pinctrl driver the GPIO driver can
just assign gpiochip_generic_config() (introduced in this patch) to
.set_config and that will take care configuration requests are directed
to the pinctrl driver.
We then convert the existing drivers over .set_config() and finally
remove the .set_single_ended() and .set_debounce() callbacks.
Suggested-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When a GPIO driver is backed by a pinctrl driver the GPIO driver
sometimes needs to call the pinctrl driver to configure certain things,
like whether the pin is used as input or output. In addition to this
there are other configurations applicable to GPIOs such as setting
debounce time of the GPIO.
To support this we introduce a new function pinctrl_gpio_set_config()
that can be used by gpiolib based driver to pass configuration requests
to the backing pinctrl driver.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The current pinconf packed format allows only 16-bit argument limiting
the maximum value 65535. For most types this is enough. However,
debounce time can be in range of hundreths of milliseconds in case of
mechanical switches so we cannot represent the worst case using the
current format.
In order to support larger values change the packed format so that the
lower 8 bits are used as type which leaves 24 bits for the argument.
This allows representing values up to 16777215 and debounce times up to
16 seconds.
We also convert the existing users to use 32-bit integer when extracting
argument from the packed configuration value.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
A cleanup caused a harmless warning:
drivers/pinctrl/mvebu/pinctrl-kirkwood.c: In function 'kirkwood_pinctrl_probe':
drivers/pinctrl/mvebu/pinctrl-kirkwood.c:460:19: error: unused variable 'res' [-Werror=unused-variable]
The obvious fix is to remove the declaration of the now unused
variable.
Fixes: ad9ec4ecee68 ("pinctrl: mvebu: switch drivers to generic simple mmio")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This is less straight-forward than one would hope, as some banks only
have 4 pins rather than 8, others are output only, yet more (W and
X, already supported) are input-only, and in the case of the g4 SoC bank
AC doesn't exist.
Add some structs to describe the varying properties of different banks
and integrate mechanisms to deny requests for unsupported
configurations.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Incorrect video output configuration bits were being tested on pins in
GPIO banks AA and AB for the ROM{8,16} mux functions. The ROM{8,16}
functions are the highest priority for the relevant pins and also the
default function, so we require the relevant video output configuration
be disabled to mux GPIO functionality. As the wrong bits were being
tested a GPIO export would succeed but leave the pin in an unresponsive
state (i.e. value updates were ignored).
This misbehaviour was discovered as part of extending the GPIO
controller's support to cover banks Y, Z, AA, AB and AC (AC in the case
of the g5 SoC).
Fixes: 6d329f14a75f ("pinctrl: aspeed-g4: Add mux configuration for all pins")
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The Aspeed SoCs have more GPIOs than can be represented with A-Z. The
documentation uses two letter names such as AA and AB, so make the names
a three-character array in the bank struct to accommodate this.
Signed-off-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
In some rare configurations we can run into rather high kernel stack
consumption:
drivers/regulator/s2mpa01.c:397:1: error: the frame size of 1536 bytes is larger than 1152 bytes [-Werror=frame-larger-than=]
This is probably harmless since it happens only in the probe function,
but there is also a relatively simple workaround, moving the regulator
match data into the device specific structure.
As a small downside, we waste a little memory at runtime. An alternative
approach would free the array at the end of the probe function, which in
turn is a little more complicated.
Fixes: f18792714608 ("regulator: Add support for S2MPA01 regulator")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
REDMEMB[17] is the ECC_Locator bit, which, when set, identifies the
CS[3:2] as the simbols in error. And thus the second channel.
The macro computing it was wrong so get rid of it (it was used at one
place only) and get rid of the conditional too. Generates better code
this way anyway.
Signed-off-by: Borislav Petkov <bp@suse.de>
Reported-by: David Binderman <dcb314@hotmail.com>
Reviewed-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The MSM pinctrl driver currently implements an irq_chip for handling
GPIO interrupts; due to how irq_chip handling is done, it's necessary
for the irq_chip methods to be invoked from hardirq context, even on a
a real-time kernel. Because the spinlock_t type becomes a "sleeping"
spinlock w/ RT kernels, it is not suitable to be used with irq_chips.
A quick audit of the operations under the lock reveal that they do only
minimal, bounded work, and are therefore safe to do under a raw
spinlock.
On real-time kernels, this fixes an OOPs which looks like the following,
as reported by Brian Wrenn:
kernel BUG at kernel/locking/rtmutex.c:1014!
Internal error: Oops - BUG: 0 [#1] PREEMPT SMP
Modules linked in: spidev_irq(O) smsc75xx wcn36xx [last unloaded: spidev]
CPU: 0 PID: 1163 Comm: irq/144-mmc0 Tainted: G W O 4.4.9-linaro-lt-qcom #1
PC is at rt_spin_lock_slowlock+0x80/0x2d8
LR is at rt_spin_lock_slowlock+0x68/0x2d8
[..]
Call trace:
rt_spin_lock_slowlock
rt_spin_lock
msm_gpio_irq_ack
handle_edge_irq
generic_handle_irq
msm_gpio_irq_handler
generic_handle_irq
__handle_domain_irq
gic_handle_irq
Reported-by: Brian Wrenn <dcbrianw@gmail.com>
Tested-by: Brian Wrenn <dcbrianw@gmail.com>
Signed-off-by: Julia Cartwright <julia@ni.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Return proper error code in case of memory allocation failure.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Memory subsystem already prints message about failed memory
allocation, there is no need to do it in the drivers.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing compatible id for Exynos3250 SoC to device tree docs.
Exynos pin control driver supports it since commit d97f5b9804bfcdc1
("pinctrl: exynos: Add driver data for Exynos3250").
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Tomasz Figa <tomasz.figa@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
If we try to allocate memory pages to back an xfs_buf that we're trying
to read, it's possible that we'll be so short on memory that the page
allocation fails. For a blocking read we'll just wait, but for
readahead we simply dump all the pages we've collected so far.
Unfortunately, after dumping the pages we neglect to clear the
_XBF_PAGES state, which means that the subsequent call to xfs_buf_free
thinks that b_pages still points to pages we own. It then double-frees
the b_pages pages.
This results in screaming about negative page refcounts from the memory
manager, which xfs oughtn't be triggering. To reproduce this case,
mount a filesystem where the size of the inodes far outweighs the
availalble memory (a ~500M inode filesystem on a VM with 300MB memory
did the trick here) and run bulkstat in parallel with other memory
eating processes to put a huge load on the system. The "check summary"
phase of xfs_scrub also works for this purpose.
Signed-off-by: Darrick J. Wong <darrick.wong@oracle.com>
Reviewed-by: Eric Sandeen <sandeen@redhat.com>
|
|
Simon Wunderlich says:
====================
Here is a batman-adv bugfix:
- fix reference count handling on fragmentation error, by Sven Eckelmann
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
commit 17bedab27231 ("bpf: xdp: Allow head adjustment in XDP prog")
added a new XDP helper to prepend and remove data from a frame.
Make virtio_net reject programs making use of this helper until
proper support is added.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Acked-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the small buffer case during driver unload we currently use
put_page instead of dev_kfree_skb. Resolve this by adding a check
for virtnet mode when checking XDP queue type. Also name the
function so that the code reads correctly to match the additional
check.
Fixes: bb91accf2733 ("virtio-net: XDP support for small buffers")
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hayes Wang says:
====================
r8152: fix scheduling napi
v3:
simply the argument for patch #3. Replace &tp->napi with napi.
v2:
Add smp_mb__after_atomic() for patch #1.
v1:
Scheduling the napi during the following periods would let it be ignored.
And the events wouldn't be handled until next napi_schedule() is called.
1. after napi_disable and before napi_enable().
2. after all actions of napi function is completed and before calling
napi_complete().
If no next napi_schedule() is called, tx or rx would stop working.
In order to avoid these situations, the followings solutions are applied.
1. prevent start_xmit() from calling napi_schedule() during runtime suspend
or after napi_disable().
2. re-schedule the napi for tx if it is necessary.
3. check if any rx is finished or not after napi_enable().
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Schedule the napi after napi_enable() for rx, if it is necessary.
If the rx is completed when napi is disabled, the sheduling of napi
would be lost. Then, no one handles the rx packet until next napi
is scheduled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Re-schedule napi after napi_complete() for tx, if it is necessay.
In r8152_poll(), if the tx is completed after tx_bottom() and before
napi_complete(), the scheduling of napi would be lost. Then, no
one handles the next tx until the next napi_schedule() is called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Stop the tx when the napi is disabled to prevent napi_schedule() is
called.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust the setting of the flag of SELECTIVE_SUSPEND to prevent start_xmit()
from calling napi_schedule() directly during runtime suspend.
After calling napi_disable() or clearing the flag of WORK_ENABLE,
scheduling the napi is useless.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When system enters VLLS mode, module power is turned off. As a result,
all registers are reset to HW default value. After exiting VLLS mode,
registers are still in default mode. As a result, the pinctrl settings
are incorrect, which will affect the module function.
The patch recovers the pinctrl setting when exit VLLS mode.
Signed-off-by: Gao Pan <pandy.gao@nxp.com>
Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>
[wsa: added missing include]
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This seems to break reboot on some evergreen systems.
bugs:
https://bugs.freedesktop.org/show_bug.cgi?id=99524
https://bugzilla.kernel.org/show_bug.cgi?id=192271
This reverts commit a481daa88fd4d6b54f25348972bba10b5f6a84d0.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
