| Age | Commit message (Collapse) | Author |
|---|
|
Commit 8d479237727c ("serial: amba-pl011: add RS485 support") sought to
keep RTS deasserted on set_mctrl if rs485 is enabled. However it did so
only if deasserted RTS polarity is high. Fix it in case it's low.
Fixes: 8d479237727c ("serial: amba-pl011: add RS485 support")
Cc: stable@vger.kernel.org # v5.15+
Cc: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Signed-off-by: Jochen Mades <jochen@mades.net>
[lukas: copyedit commit message, add stable designation]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/85fa3323ba8c307943969b7343e23f34c3e652ba.1642909284.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
x_char is ignored by stm32_usart_start_tx() when xmit buffer is empty.
Fix start_tx condition to allow x_char to be sent.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-3-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When sending x_char in stm32_usart_transmit_chars(), driver can overwrite
the value of TDR register by the value of x_char. If this happens, the
previous value that was present in TDR register will not be sent through
uart.
This code checks if the previous value in TDR register is sent before
writing the x_char value into register.
Fixes: 48a6092fb41f ("serial: stm32-usart: Add STM32 USART Driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Link: https://lore.kernel.org/r/20220111164441.6178-2-valentin.caron@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
n_gsm is based on the 3GPP 07.010 and its newer version is the 3GPP 27.010.
See https://portal.3gpp.org/desktopmodules/Specifications/SpecificationDetails.aspx?specificationId=1516
The changes from 07.010 to 27.010 are non-functional. Therefore, I refer to
the newer 27.010 here. Chapter 5.2.7.3 states that DC1 (XON) and DC3 (XOFF)
are the control characters defined in ISO/IEC 646. These shall be quoted if
seen in the data stream to avoid interpretation as flow control characters.
ISO/IEC 646 refers to the set of ISO standards described as the ISO
7-bit coded character set for information interchange. Its final version
is also known as ITU T.50.
See https://www.itu.int/rec/T-REC-T.50-199209-I/en
To abide the standard it is needed to quote DC1 and DC3 correctly if these
are seen as data bytes and not as control characters. The current
implementation already tries to enforce this but fails to catch all
defined cases. 3GPP 27.010 chapter 5.2.7.3 clearly states that the most
significant bit shall be ignored for DC1 and DC3 handling. The current
implementation handles only the case with the most significant bit set 0.
Cases in which DC1 and DC3 have the most significant bit set 1 are left
unhandled.
This patch fixes this by masking the data bytes with ISO_IEC_646_MASK (only
the 7 least significant bits set 1) before comparing them with XON
(a.k.a. DC1) and XOFF (a.k.a. DC3) when testing which byte values need
quotation via byte stuffing.
Fixes: e1eaea46bb40 ("tty: n_gsm line discipline")
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Starke <daniel.starke@siemens.com>
Link: https://lore.kernel.org/r/20220120101857.2509-1-daniel.starke@siemens.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
8250_of supports a reg-offset property which is intended to handle
cases where the device registers start at an offset inside the region
of memory allocated to the device. The Xilinx 16550 UART, for which this
support was initially added, requires this. However, the code did not
adjust the overall size of the mapped region accordingly, causing the
driver to request an area of memory past the end of the device's
allocation. For example, if the UART was allocated an address of
0xb0130000, size of 0x10000 and reg-offset of 0x1000 in the device
tree, the region of memory reserved was b0131000-b0140fff, which caused
the driver for the region starting at b0140000 to fail to probe.
Fix this by subtracting reg-offset from the mapped region size.
Fixes: b912b5e2cfb3 ([POWERPC] Xilinx: of_serial support for Xilinx uart 16550.)
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220112194214.881844-1-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The tty_port struct is part of the rpmsg_tty_port structure.
The issue is that the rpmsg_tty_port structure is freed on
rpmsg_tty_remove while it is still referenced in the tty_struct.
Its release is not predictable due to workqueues.
For instance following ftrace shows that rpmsg_tty_close is called after
rpmsg_tty_release_cport:
nr_test.sh-389 [000] ..... 212.093752: rpmsg_tty_remove <-rpmsg_dev_
remove
cat-1191 [001] ..... 212.095697: tty_release <-__fput
nr_test.sh-389 [000] ..... 212.099166: rpmsg_tty_release_cport <-rpm
sg_tty_remove
cat-1191 [001] ..... 212.115352: rpmsg_tty_close <-tty_release
cat-1191 [001] ..... 212.115371: release_tty <-tty_release_str
As consequence, the port must be free only when user has released the TTY
interface.
This path :
- Introduce the .destruct port tty ops function to release the allocated
rpmsg_tty_port structure.
- Introduce the .hangup tty ops function to call tty_port_hangup.
- Manages the tty port refcounting to trig the .destruct port ops,
- Introduces the rpmsg_tty_cleanup function to ensure that the TTY is
removed before decreasing the port refcount.
Fixes: 7c0408d80579 ("tty: add rpmsg driver")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Arnaud Pouliquen <arnaud.pouliquen@foss.st.com>
Link: https://lore.kernel.org/r/20220104163545.34710-1-arnaud.pouliquen@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a user API regression introduced with commit f76edd8f7ce0 ("tty:
cyclades, remove this orphan"), which removed a part of the API and
caused compilation errors for user programs using said part, such as
GCC 9 in its libsanitizer component[1]:
.../libsanitizer/sanitizer_common/sanitizer_platform_limits_posix.cc:160:10: fatal error: linux/cyclades.h: No such file or directory
160 | #include <linux/cyclades.h>
| ^~~~~~~~~~~~~~~~~~
compilation terminated.
make[4]: *** [Makefile:664: sanitizer_platform_limits_posix.lo] Error 1
As the absolute minimum required bring `struct cyclades_monitor' and
ioctl numbers back then so as to make the library build again. Add a
preprocessor warning as to the obsolescence of the features provided.
References:
[1] GCC PR sanitizer/100379, "cyclades.h is removed from linux kernel
header files", <https://gcc.gnu.org/bugzilla/show_bug.cgi?id=100379>
Fixes: f76edd8f7ce0 ("tty: cyclades, remove this orphan")
Cc: stable@vger.kernel.org # v5.13+
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Maciej W. Rozycki <macro@embecosm.com>
Link: https://lore.kernel.org/r/alpine.DEB.2.20.2201260733430.11348@tpp.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This commit adds support for the some of the Brainboxes PCI range of
cards, including the UC-101, UC-235/246, UC-257, UC-268, UC-275/279,
UC-302, UC-310, UC-313, UC-320/324, UC-346, UC-357, UC-368
and UC-420/431.
Signed-off-by: Cameron Williams <cang1@live.co.uk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/AM5PR0202MB2564688493F7DD9B9C610827C45E9@AM5PR0202MB2564.eurprd02.prod.outlook.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If blk_mq_request_issue_directly() failed from
blk_insert_cloned_request(), the request will be accounted start.
Currently, blk_insert_cloned_request() is only called by dm, and such
request won't be accounted done by dm.
In normal path, io will be accounted start from blk_mq_bio_to_request(),
when the request is allocated, and such io will be accounted done from
__blk_mq_end_request_acct() whether it succeeded or failed. Thus add
blk_account_io_done() to fix the problem.
Signed-off-by: Yu Kuai <yukuai3@huawei.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Link: https://lore.kernel.org/r/20220126012132.3111551-1-yukuai3@huawei.com
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
This reverts commit 5021d709b31b8a14317998a33cbc78be0de9ab30.
The patch is still a bit buggy, and this breaks some other hardware
types. It needs to be resubmitted in a non-buggy way, and make sure the
other hardware types also continue to work properly.
Fixes: 5021d709b31b ("tty: serial: Use fifo in 8250 console driver")
Reported-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/Ye/1+Z8mEzbKbrqG@linutronix.de
Link: https://lore.kernel.org/r/a1ac6254-f79e-d131-fa2a-c7ad714c6d4a@nvidia.com
Cc: Wander Lairson Costa <wander@redhat.com>
Cc: Andy Shevchenko <andy.shevchenko@gmail.com>
Cc: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This check misses checking for platform_get_irq()'s call and may passes
the negative error codes to devm_request_irq(), which takes unsigned IRQ #,
causing it to fail with -EINVAL, overriding an original error code.
Stop calling devm_request_irq() with invalid IRQ #s.
Fixes: 454fa271bc4e ("spi: Add Meson SPICC driver")
Signed-off-by: Miaoqian Lin <linmq006@gmail.com>
Link: https://lore.kernel.org/r/20220126110447.24549-1-linmq006@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Its possible that the sound card is just opened and closed without actually
playing stream, ex: if the audio file itself is missing.
Even in such cases we do call stop on graphs that are not yet started.
DSP can throw errors in such cases, so add a check to see if the graph
was started before stopping it.
Fixes: 9b4fe0f1cd79 ("ASoC: qdsp6: audioreach: add q6apm-dai support")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-5-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
wcd938x_ear_pa_put_gain, wcd938x_set_swr_port and wcd938x_set_compander
currently returns zero eventhough it changes the value.
Fix this, so that change notifications are sent correctly.
Fixes: e8ba1e05bdc01 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-4-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For some reason we ended up with incorrect register offfset calcuations
for sidetone. regmap clearly throw errors when accessing these incorrect
registers as these do not belong to any read/write ranges.
so fix them to point to correct register offsets.
Fixes: f3ce6f3c9a99 ("ASoC: codecs: lpass-rx-macro: add iir widgets")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-3-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Mixer controls have the channel id in mixer->reg, which is not same
as port id. port id should be derived from chan_info array.
So fix this. Without this, its possible that we could corrupt
struct wcd938x_sdw_priv by accessing port_map array out of range
with channel id instead of port id.
Fixes: e8ba1e05bdc0 ("ASoC: codecs: wcd938x: add basic controls")
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Link: https://lore.kernel.org/r/20220126113549.8853-2-srinivas.kandagatla@linaro.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
GPIO7_IO00 is used as SD card detect.
Properly describe this in the devicetree.
Fixes: 40cdaa542cf0 ("ARM: dts: imx6q-udoo: Add initial board support")
Signed-off-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
CDNSP driver read not initialized cdns->otg_v0_regs
which lead to segmentation fault. Patch fixes this issue.
Fixes: 2cf2581cd229 ("usb: cdns3: add power lost support for system resume")
cc: <stable@vger.kernel.org>
Signed-off-by: Pawel Laszczak <pawell@cadence.com>
Link: https://lore.kernel.org/r/20220111090737.10345-1-pawell@gli-login.cadence.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In uniphier_spi_remove(), there is a wrong code to get private data from
the platform device, so the driver can't be removed properly.
The driver should get spi_master from the platform device and retrieve
the private data from it.
Cc: <stable@vger.kernel.org>
Fixes: 5ba155a4d4cc ("spi: add SPI controller driver for UniPhier SoC")
Signed-off-by: Kunihiko Hayashi <hayashi.kunihiko@socionext.com>
Link: https://lore.kernel.org/r/1640148492-32178-1-git-send-email-hayashi.kunihiko@socionext.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The corresponding API for clk_prepare is clk_unprepare, other than
clk_disable_unprepare.
Fix this by changing clk_disable_unprepare to clk_unprepare.
Fixes: 5762ab71eb24 ("spi: Add support for Armada 3700 SPI Controller")
Signed-off-by: Dongliang Mu <mudongliangabcd@gmail.com>
Link: https://lore.kernel.org/r/20211206101931.2816597-1-mudongliangabcd@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Calling dwc2_hsotg_ep_disable on ep0 (in/out) will lead to the following
logs before returning -EINVAL:
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
dwc2 49000000.usb-otg: dwc2_hsotg_ep_disable: called for ep0
To avoid these two logs while suspending, start disabling the endpoint
from the index 1, as done in dwc2_hsotg_udc_stop:
/* all endpoints should be shutdown */
for (ep = 1; ep < hsotg->num_of_eps; ep++) {
if (hsotg->eps_in[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_in[ep]->ep);
if (hsotg->eps_out[ep])
dwc2_hsotg_ep_disable_lock(&hsotg->eps_out[ep]->ep);
}
Acked-by: Minas Harutyunyan <Minas.Harutyunyan@synopsys.com>
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20211207130101.270314-1-amelie.delaunay@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix a build error observed with ARCH=arm DEFCONFIG=allmodconfig build.
drivers/usb/gadget/udc/at91_udc.h:174:42: error: format '%d' expects argument of type 'int', but argument 3 has type 'struct gpio_desc *' [-Werror=format=]
Fixes: 4a555f2b8d31 ("usb: gadget: at91_udc: Convert to GPIO descriptors")
Reviewed-by: Macpaul Lin <macpaul.lin@mediatek.com>
Signed-off-by: Miles Chen <miles.chen@mediatek.com>
Link: https://lore.kernel.org/r/20220119020849.25732-1-miles.chen@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The code that looked up the USB3 PHY was ignoring all errors other than
EPROBE_DEFER in an attempt to handle the PHY not being present. Fix and
simplify the code by using devm_phy_optional_get and dev_err_probe so
that a missing PHY is not treated as an error and unexpected errors
are handled properly.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-3-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It appears that the PIPE clock should not be selected when only USB 2.0
is being used in the design and no USB 3.0 reference clock is used.
Also, the core resets are not required if a USB3 PHY is not in use, and
will break things if USB3 is actually used but the PHY entry is not
listed in the device tree.
Skip core resets and register settings that are only required for
USB3 mode when no USB3 PHY is specified in the device tree.
Fixes: 84770f028fab ("usb: dwc3: Add driver for Xilinx platforms")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Robert Hancock <robert.hancock@calian.com>
Link: https://lore.kernel.org/r/20220126000253.1586760-2-robert.hancock@calian.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Crashed at i.mx8qm platform when suspend if enable remote wakeup
Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
Modules linked in:
CPU: 2 PID: 244 Comm: kworker/u12:6 Not tainted 5.15.5-dirty #12
Hardware name: Freescale i.MX8QM MEK (DT)
Workqueue: events_unbound async_run_entry_fn
pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : xhci_disable_hub_port_wake.isra.62+0x60/0xf8
lr : xhci_disable_hub_port_wake.isra.62+0x34/0xf8
sp : ffff80001394bbf0
x29: ffff80001394bbf0 x28: 0000000000000000 x27: ffff00081193b578
x26: ffff00081193b570 x25: 0000000000000000 x24: 0000000000000000
x23: ffff00081193a29c x22: 0000000000020001 x21: 0000000000000001
x20: 0000000000000000 x19: ffff800014e90490 x18: 0000000000000000
x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
x14: 0000000000000000 x13: 0000000000000002 x12: 0000000000000000
x11: 0000000000000000 x10: 0000000000000960 x9 : ffff80001394baa0
x8 : ffff0008145d1780 x7 : ffff0008f95b8e80 x6 : 000000001853b453
x5 : 0000000000000496 x4 : 0000000000000000 x3 : ffff00081193a29c
x2 : 0000000000000001 x1 : 0000000000000000 x0 : ffff000814591620
Call trace:
xhci_disable_hub_port_wake.isra.62+0x60/0xf8
xhci_suspend+0x58/0x510
xhci_plat_suspend+0x50/0x78
platform_pm_suspend+0x2c/0x78
dpm_run_callback.isra.25+0x50/0xe8
__device_suspend+0x108/0x3c0
The basic flow:
1. run time suspend call xhci_suspend, xhci parent devices gate the clock.
2. echo mem >/sys/power/state, system _device_suspend call xhci_suspend
3. xhci_suspend call xhci_disable_hub_port_wake, which access register,
but clock already gated by run time suspend.
This problem was hidden by power domain driver, which call run time resume before it.
But the below commit remove it and make this issue happen.
commit c1df456d0f06e ("PM: domains: Don't runtime resume devices at genpd_prepare()")
This patch call run time resume before suspend to make sure clock is on
before access register.
Reviewed-by: Peter Chen <peter.chen@kernel.org>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Frank Li <Frank.Li@nxp.com>
Testeb-by: Abel Vesa <abel.vesa@nxp.com>
Link: https://lore.kernel.org/r/20220110172738.31686-1-Frank.Li@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Commit 7495af930835 ("ARM: multi_v7_defconfig: Enable drivers for
DragonBoard 410c") enables the CONFIG_PHY_QCOM_USB_HS for the ARM
multi_v7_defconfig. Enabling this Kconfig is causing the kernel to crash
on the Tegra20 Ventana platform in the ulpi_match() function.
The Qualcomm USB HS PHY driver that is enabled by CONFIG_PHY_QCOM_USB_HS,
registers a ulpi_driver but this driver does not provide an 'id_table',
so when ulpi_match() is called on the Tegra20 Ventana platform, it
crashes when attempting to deference the id_table pointer which is not
valid. The Qualcomm USB HS PHY driver uses device-tree for matching the
ULPI driver with the device and so fix this crash by using device-tree
for matching if the id_table is not valid.
Fixes: ef6a7bcfb01c ("usb: ulpi: Support device discovery via DT")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20220117150039.44058-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently when gadget enumerates in super speed plus, the isoc
endpoint request buffer size is not calculated correctly. Fix
this by checking the gadget speed against USB_SPEED_SUPER_PLUS
and update the request buffer size.
Fixes: 90c4d05780d4 ("usb: fix various gadgets null ptr deref on 10gbps cabling.")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Pavankumar Kondeti <quic_pkondeti@quicinc.com>
Link: https://lore.kernel.org/r/1642820602-20619-1-git-send-email-quic_pkondeti@quicinc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
CCGx clears Bit 0:Device Interrupt in the INTR_REG
if CCGx is reset successfully. However, there might
be a chance that other bits in INTR_REG are not
cleared due to internal data queued in PPM. This case
misleads the driver that CCGx reset failed.
The commit checks bit 0 in INTR_REG and ignores other
bits. The ucsi driver would reset PPM later.
Fixes: 247c554a14aa ("usb: typec: ucsi: add support for Cypress CCGx")
Cc: stable@vger.kernel.org
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Sing-Han Chen <singhanc@nvidia.com>
Signed-off-by: Wayne Chang <waynec@nvidia.com>
Link: https://lore.kernel.org/r/20220112094143.628610-1-waynec@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 99aa29932271 ("arm64: dts: imx8mn: Enable GPU")
imx8mn-venice-gw7902 will hang during kernel init because it uses
a MIMX8MN5CVTI which does not have a GPU.
Disable pgc_gpumix to work around this. We also disable the GPU devices
that depend on the gpumix power domain and pgc_gpu to avoid them staying
in a probe deferred state forever.
Cc: Adam Ford <aford173@gmail.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Fixes: 99aa29932271 ("arm64: dts: imx8mn: Enable GPU")
Reviewed-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A recent bug report outlined that the way GICv4.1 is handled across
kexec is pretty bad. We can end-up in a situation where ITSs share
memory (this is the case when SVPET==1) and reprogram the base
registers, creating a situation where ITSs that are part of a given
affinity group see different pointers. Which is illegal. Boo.
In order to restore some sanity, reset the BASERn registers to 0
*before* probing any ITS. Although this isn't optimised at all,
this is only a once-per-boot cost, which shouldn't show up on
anyone's radar.
Cc: Jay Chen <jkchen@linux.alibaba.com>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Reviewed-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Link: https://lore.kernel.org/r/20211216190315.GA14220@lpieralisi
Link: https://lore.kernel.org/r/20220124133809.1291195-1-maz@kernel.org
|
|
This reverts commit 9bb7b689274b67ecb3641e399e76f84adc627df1.
This caused a regression reported to Red Hat.
Fixes: 9bb7b689274b ("drm/ast: Support 1600x900 with 108MHz PCLK")
Signed-off-by: Dave Airlie <airlied@redhat.com>
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/20220120040527.552068-1-airlied@gmail.com
|
|
Backmerging drm/drm-fixes into drm-misc-fixes for v5.17-rc1.
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
|
|
The current implementation of HTB offload doesn't support some
parameters. Instead of ignoring them, actively return the EINVAL error
when they are set to non-defaults.
As this patch goes to stable, the driver API is not changed here. If
future drivers support more offload parameters, the checks can be moved
to the driver side.
Note that the buffer and cbuffer parameters are also not supported, but
the tc userspace tool assigns some default values derived from rate and
ceil, and identifying these defaults in sch_htb would be unreliable, so
they are still ignored.
Fixes: d03b195b5aa0 ("sch_htb: Hierarchical QoS hardware offload")
Reported-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Maxim Mikityanskiy <maximmi@nvidia.com>
Reviewed-by: Tariq Toukan <tariqt@nvidia.com>
Link: https://lore.kernel.org/r/20220125100654.424570-1-maximmi@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The lirc.h file is an old copy of lirc.h from the kernel sources. It is
out of date, and the bpf lirc tests don't need a new copy anyway. As
long as /usr/include/linux/lirc.h is from kernel v5.2 or newer, the tests
will compile fine.
Signed-off-by: Sean Young <sean@mess.org>
Reviewed-by: Shuah Khan <skhan@linuxfoundation.org>
Link: https://lore.kernel.org/r/20220124153028.394409-1-sean@mess.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
It seems inc_misses_counter() suffers from same issue fixed in
the commit d979617aa84d ("bpf: Fixes possible race in update_prog_stats()
for 32bit arches"):
As it can run while interrupts are enabled, it could
be re-entered and the u64_stats syncp could be mangled.
Fixes: 9ed9e9ba2337 ("bpf: Count the number of times recursion was prevented")
Signed-off-by: He Fengqing <hefengqing@huawei.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/r/20220122102936.1219518-1-hefengqing@huawei.com
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Function pcie_rmw() is not being used at all and can be deleted. Hence get
rid of it, which fixes this warning:
drivers/pci/controller/pcie-mt7621.c:112:20: warning: unused function 'pcie_rmw' [-Wunused-function]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-3-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/all/202201241754.igtHzgHv-lkp@intel.com/
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
We have stubs for most OF interfaces even when CONFIG_OF is not set, so we
allow building of pcie-mt7621.c in that case for compile testing.
When CONFIG_OF is not set, "of_match_ptr(mt7621_pcie_ids)" compiles to
NULL, which leaves mt7621_pcie_ids unused:
$ make W=1
drivers/pci/controller/pcie-mt7621.c:549:34: warning: unused variable 'mt7621_pcie_ids' [-Wunused-const-variable]
Drop of_match_ptr() to avoid the unused variable warning.
[bhelgaas: commit log]
Fixes: 2bdd5238e756 ("PCI: mt7621: Add MediaTek MT7621 PCIe host controller driver")
Link: https://lore.kernel.org/r/20220124113003.406224-2-sergio.paracuellos@gmail.com
Link: https://lore.kernel.org/r/202201241754.igtHzgHv-lkp@intel.com
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sergio Paracuellos <sergio.paracuellos@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Unused. Convert the divisions into asserts on the divisor, to
debug why it is zero. The divide by zero is suspected of causing
kernel panics.
While I have no idea where the zero is coming from I think this
patch is a positive either way.
Cc: stable@vger.kernel.org
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Mirrors the logic for dcn30. Cue lots of WARNs and some
kernel panics without this fix.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It calls populate_dml_pipes which uses doubles to initialize the
scale_ratio_depth params. Mirrors the dcn20 logic.
Cc: stable@vger.kernel.org
Signed-off-by: Bas Nieuwenhuizen <bas@basnieuwenhuizen.nl>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
In calculate_bandwidth(), the tag free_sclk and free_yclk are reversed,
which could lead to a memory leak of yclk.
Fix this bug by changing the location of free_sclk and free_yclk.
This bug was found by a static analyzer.
Builds with 'make allyesconfig' show no new warnings,
and our static analyzer no longer warns about this code.
Fixes: 2be8989d0fc2 ("drm/amd/display/dc/calcs/dce_calcs: Move some large variables from the stack to the heap")
Signed-off-by: Zhou Qingyang <zhou1615@umn.edu>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) throw an compilation error if the
udelay is too long. In general udelays of longer than 2000us are
not recommended on any architecture. Switch to msleep in these
cases.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Some architectures (e.g., ARM) have relatively low udelay limits.
On most architectures, anything longer than 2000us is not recommended.
Change the check to align with other similar checks in DC.
Reviewed-by: Harry Wentland <harry.wentland@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Older radeon boards (r2xx-r5xx) had secondary PCI functions
which we solely there for supporting multi-head on OSs with
special requirements. Add them to the unsupported list
as well so we don't attempt to bind to them. The driver
would fail to bind to them anyway, but this does so
in a cleaner way that should not confuse the user.
Cc: stable@vger.kernel.org
Acked-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
FIFO reset is only necessary for fast boot sequence, where otg is disabled
and dig fe is enabled when changing dispclk. Fast boot is only enabled
on embedded displays.
[How]
Change FIFO reset condition to "embedded display only".
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
DCN301 has seamless boot enabled. With MPC split enabled
at the same time, system will hang.
[How]
Revert MPC split policy back to "MPC_SPLIT_AVOID". Since we have
ODM combine enabled on DCN301, pipe split is not necessary here.
Signed-off-by: Zhan Liu <zhan.liu@amd.com>
Reviewed-by: Charlene Liu <charlene.liu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
During otg sync trigger, plane states are used to decide whether the otg
is already synchronized or not. There are scenarions when otgs are
disabled without plane state getting disabled and in such case the otg is
excluded from synchronization.
[How]
Introduced pipe_idx_syncd in pipe_ctx that tracks each otgs master pipe.
When a otg is disabled/enabled, pipe_idx_syncd is reset to itself.
On sync trigger, pipe_idx_syncd is checked to decide whether a otg is
already synchronized and the otg is further included or excluded from
synchronization.
v2:
Don't drop is_blanked logic
Reviewed-by: Jun Lei <Jun.Lei@amd.com>
Reviewed-by: Mustapha Ghaddar <mustapha.ghaddar@amd.com>
Acked-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Signed-off-by: meenakshikumar somasundaram <meenakshikumar.somasundaram@amd.com>
Tested-by: Daniel Wheeler <daniel.wheeler@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Harry Wentland <harry.wentland@amd.com>
Cc: torvalds@linux-foundation.org
Reviewed-by: Alex Deucher <alexander.deucher@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The membarrier command MEMBARRIER_CMD_QUERY allows querying the
available membarrier commands. When the membarrier-rseq fence commands
were added, a new MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK was
introduced with the intent to expose them with the MEMBARRIER_CMD_QUERY
command, the but it was never added to MEMBARRIER_CMD_BITMASK.
The membarrier-rseq fence commands are therefore not wired up with the
query command.
Rename MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ_BITMASK to
MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK (the bitmask is not a command
per-se), and change the erroneous
MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ_BITMASK (which does not
actually exist) to MEMBARRIER_CMD_REGISTER_PRIVATE_EXPEDITED_RSEQ.
Wire up MEMBARRIER_PRIVATE_EXPEDITED_RSEQ_BITMASK in
MEMBARRIER_CMD_BITMASK. Fixing this allows discovering availability of
the membarrier-rseq fence feature.
Fixes: 2a36ab717e8f ("rseq/membarrier: Add MEMBARRIER_CMD_PRIVATE_EXPEDITED_RSEQ")
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Cc: <stable@vger.kernel.org> # 5.10+
Link: https://lkml.kernel.org/r/20220117203010.30129-1-mathieu.desnoyers@efficios.com
|
|
We have some many cases that will create child process as well, such as
pidfd_wait. Previously, we will signal/kill the parent process when it
is time out, but this signal will not be sent to its child process. In
such case, if child process doesn't terminate itself, ksefltest framework
will hang forever.
Here we group all its child processes so that kill() can signal all of
them in timeout.
Fixed change log: Shuah Khan <skhan@linuxfoundation.org>
Suggested-by: yang xu <xuyang2018.jy@cn.fujitsu.com>
Signed-off-by: Li Zhijian <lizhijian@cn.fujitsu.com>
Acked-by: Christian Brauner <christian.brauner@ubuntu.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
Use 'tee' to send the test output to stdout in addition to the current
output file. This makes the output easier to handle in automated test
systems and is superior to only later dumping the output file contents
to stdout, since this way the test output can be interleaved with other
log messages, like from the kernel, so that chronology is preserved,
making it easier to detect issues.
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
|
The timeout setting for the rtc kselftest is currently 90 seconds. This
setting is used by the kselftest runner to stop running a test if it
takes longer than the assigned value.
However, two of the test cases inside rtc set alarms. These alarms are
set to the next beginning of the minute, so each of these test cases may
take up to, in the worst case, 60 seconds.
In order to allow for all test cases in rtc to run, even in the worst
case, when using the kselftest runner, the timeout value should be
increased to at least 120. Set it to 180, so there's some additional
slack.
Correct operation can be tested by running the following command right
after the start of a minute (low second count), and checking that all
test cases run:
./run_kselftest.sh -c rtc
Signed-off-by: Nícolas F. R. A. Prado <nfraprado@collabora.com>
Acked-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Shuah Khan <skhan@linuxfoundation.org>
|
