| Age | Commit message (Collapse) | Author |
|---|
|
And a test for it:
[acme@felicio linux]$ perf test
1: vmlinux symtab matches kallsyms: Ok
2: detect open syscall event: Ok
3: detect open syscall event on all cpus: Ok
[acme@felicio linux]$
Translating C the test does:
1. generates different number of open syscalls on each CPU
by using sched_setaffinity
2. Verifies that the expected number of events is generated
on each CPU
It works as expected.
LKML-Reference: <new-submission>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Mike Galbraith <efault@gmx.de>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Stephane Eranian <eranian@google.com>
Cc: Tom Zanussi <tzanussi@gmail.com>
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
The size field should not be set until after the data is successfully
copied in.
Signed-off-by: Dan Rosenberg <drosenberg@vsecurity.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We perform the microseconds to loops calculation using a number of
multiplies and shift rights. Each shift right rounds down the
resulting value, which can result in delays shorter than requested.
Ensure that we always round up.
Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
|
|
Some platforms have been known to return NULL from clk_get() if they
support only a single struct clk. Whilst tegra doesn't do this, make
the drivers consistent with others.
Signed-off-by: Jamie Iles <jamie@jamieiles.com>
Acked-by: Russell King <linux@arm.linux.org.uk>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86
* 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mjg59/platform-drivers-x86: (36 commits)
sony-laptop: support new hotkeys on the P, Z and EC series
platform/x86: Consistently select LEDS Kconfig options
sony-laptop: fix sparse non-ANSI function warning
intel_ips: fix sparse non-ANSI function warning
Support KHLB2 in the compal laptop driver
acer-wmi: Enabled Acer Launch Manager mode
[PATCH] intel_pmic_gpio: modify EOI handling following change of kernel irq subsystem
ACPI Thinkpad: We must always call va_end() after va_start() but do not do so in thinkpad_acpi.c::acpi_evalf()
acer-wmi: Initialize wlan/bluetooth/wwan rfkill software block state
acer-wmi: Detect the WiFi/Bluetooth/3G devices available
acer-wmi: Add 3G rfkill sysfs file
acer-wmi: Add acer wmi hotkey events support
platform/x86: Kconfig: Replace select by depends on ACPI_WMI
ideapad: pass ideapad_priv as argument (part 2)
ideapad: pass ideapad_priv as argument (part 1)
ideapad: add markups, unify comments and return result when init
ideapad: add hotkey support
ideapad: let camera power control entry under platform driver
ideapad: add platform driver for ideapad
fujitsu-laptop: fix compiler warning on pnp_ids
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/linux-m68k:
m68knommu: Need to check __get_user()/__put_user() result
m68knommu: signal.c __user annotations
m68knommu: Equivalent of "m68k: handle new gcc's"
m68knommu: f_pcr has been gone since headers' merge
m68knommu: Don't lose state if sigframe setup fails
m68knommu: Handle multiple pending signals
m68knommu: Switch to saner sigsuspend
m68knommu: Don't bother with SA_ONESHOT
m68k: Check __get_user()/__put_user() return value
m68k: Missing syscall_trace() on sigreturn
m68k: Fix stack mangling logics in sigreturn
m68k: If we fail to set sigframe up, just leave regs alone...
m68k: Don't lose state if sigframe setup fails
m68k: Simplify the singlestepping handling in signals
m68k: Switch to saner sigsuspend()
m68k: Resetting sa_handler in local copy of k_sigaction is pointless
m68k/sun3: Kill pte_unmap() warnings
|
|
When two concurrent unaligned, non-overlapping direct IOs are issued
to the same block, the direct Io layer will race to zero the block.
The result is that one of the concurrent IOs will overwrite data
written by the other IO with zeros. This is demonstrated by the
xfsqa test 240.
To avoid this problem, serialise all unaligned direct IOs to an
inode with a big hammer. We need a big hammer approach as we need to
serialise AIO as well, so we can't just block writes on locks.
Hence, the big hammer is calling xfs_ioend_wait() while holding out
other unaligned direct IOs from starting.
We don't bother trying to serialised aligned vs unaligned IOs as
they are overlapping IO and the result of concurrent overlapping IOs
is undefined - the result of either IO is a valid result so we let
them race. Hence we only penalise unaligned IO, which already has a
major overhead compared to aligned IO so this isn't a major problem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
The buffered IO and direct IO write paths share a common set of
checks and limiting code prior to issuing the write. Factor that
into a common helper function.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Complete the split of the different write IO paths by splitting the
buffered IO write path out of xfs_file_aio_write(). This makes the
different mechanisms of the write patchs easier to follow.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
The current xfs_file_aio_write code is a mess of locking shenanigans
to handle the different locking requirements of buffered and direct
IO. Start to clean this up by disentangling the direct IO path from
the mess.
This also removes the failed direct IO fallback path to buffered IO.
XFS handles all direct IO cases without needing to fall back to
buffered IO, so we can safely remove this unused path. This greatly
simplifies the logic and locking needed in the write path.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
We need to obtain the i_mutex, i_iolock and i_ilock during the read
and write paths. Add a set of wrapper functions to neatly
encapsulate the lock ordering and shared/exclusive semantics to make
the locking easier to follow and get right.
Note that this changes some of the exclusive locking serialisation in
that serialisation will occur against the i_mutex instead of the
XFS_IOLOCK_EXCL. This does not change any behaviour, and it is
arguably more efficient to use the mutex for such serialisation than
the rw_sem.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
xfs_file_aio_write() only returns the error from synchronous
flushing of the data and inode if error == 0. At the point where
error is being checked, it is guaranteed to be > 0. Therefore any
errors returned by the data or fsync flush will never be returned.
Fix the checks so we overwrite the current error once and only if an
error really occurred.
Signed-off-by: Dave Chinner <dchinner@redhat.com>
Reviewed-by: Alex Elder <aelder@sgi.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6
* 'release' of git://git.kernel.org/pub/scm/linux/kernel/git/aegl/linux-2.6:
[IA64] Avoid array overflow if there are too many cpus in SRAT table
[IA64] Remove unlikely from cpu_is_offline
[IA64] irq_ia64, use set_irq_chip
[IA64] perfmon: Change vmalloc to vzalloc and drop memset.
[IA64] eliminate race condition in smp_flush_tlb_mm
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson
* 'for-torvalds' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-stericsson:
ux500: allow 5500 and 8500 to be built together
ux500: modem_irq is only for 5500
ux500: dynamic SOC detection
ux500: rename MOP board Kconfig
ux500: remove build-time changing macros
|
|
* 'msm-smp' of git://codeaurora.org/quic/kernel/davidb/linux-msm:
msm: add SMP support for msm
msm: hotplug: support cpu hotplug on msm
msm: timer: SMP timer support for msm
msm: scm-boot: Support for setting cold/warm boot addresses
msm: Secure Channel Manager (SCM) support
|
|
Support twl4030 keypad and gpio keys on IGEP v2.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The second MMC channel (used by the WLAN/BT module) is not linked to
power regulator. This causes the WLAN/BT module to fail being detected if
CONFIG_REGULATOR_DUMMY is not set.
This patch adds the two regulators that actually feed the WLAN/BT module
(1v8 from the TWL4030 VIO LDO, and a fixed 3v3). With that patch, the
second channel is properly detected.
Also change vmmc1 to use symbolic names instead of direct device
reference.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Acked-by: Marc Zyngier <maz@misterjones.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Update the CS4270 driver to use ASoC's internal codec register cache feature.
This change allows ASoC to perform the low-level I2C operations necessary to
read the register cache. Support is also added for initializing the register
cache with an array of known power-on default values.
The CS4270 driver was handling the register cache itself, but somwhere along
the conversion to multi-compaonent, this feature broke.
Signed-off-by: Timur Tabi <timur@freescale.com>
Acked-by: Liam Girdwood <lrg@slimlogic.co.uk>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
|
|
The OMAP3 IGEP module has one EHCI interface on board using
USB2HS port. GPIO183 is used as PHY reset.
Signed-off-by: Enric Balletbo i Serra <eballetbo@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
At latest mainline commit 0c21e3aaf6a, omap2plus build is broken. This
patch is trivial fix for the missed usb clock node for CK_3430ES2PLUS
flag update.
CHK include/generated/compile.h
CC arch/arm/mach-omap2/clock3xxx_data.o
arch/arm/mach-omap2/clock3xxx_data.c:3289: error: 'CK_3430ES2' undeclared
here (not in a function)
make[1]: *** [arch/arm/mach-omap2/clock3xxx_data.o] Error 1
make: *** [arch/arm/mach-omap2] Error 2
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: Anand Gadiyar <gadiyar@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
[tony@atomide.com: updated mask to include CK_36XX]
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For the VFs, the Mailbox Data "registers" are actually backed by
T4's "MA" interface rather than PL Registers (as is the case for
the PFs). Because these are in different coherency domains, the
write to the VF's PL-register-backed Mailbox Control can race in
front of the writes to the MA-backed VF Mailbox Data "registers".
So we need to do a read-back on at least one byte of the VF Mailbox
Data registers before doing the write to the VF Mailbox Control
register.
Signed-off-by: Casey Leedom <leedom@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
o Updating module parameter after driver load is not supported
except auto_fw_reset parameter. Changing these parameter after
driver load, can have weird result.
o Update driver version to 5.0.15.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IRQ diag test was getting executed only when both register test
and link test passed. The test should get executed if ETH_TEST_FL_OFFLINE
flag is set.
Signed-off-by: Sony Chacko <sony.chacko@qlogic.com>
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver is reading flash fw version from defined address, this address
may be invalid. Indeed Driver should read address for fw version through
flash layout table. Flash layout table has defined region and address for
fw version address should be read from fw image region.
Driver has check for old firmware, this bug can cause driver load fail.
This patch will try to read fw version from flash image region, if that fails,
read from defined address.
Signed-off-by: Amit Kumar Salecha <amit.salecha@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Dan Rosenberg pointed out that there were some signed comparison bugs
in the phonet protocol.
http://marc.info/?l=full-disclosure&m=129424528425330&w=2
The problem is that we check for array overflows but "protocol" is
signed and we don't check for array underflows. If you have already
have CAP_SYS_ADMIN then you could use the bugs to get root, or someone
could cause an oops by mistake.
Signed-off-by: Dan Carpenter <error27@gmail.com>
Acked-by: Rémi Denis-Courmont <remi.denis-courmont@nokia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With writeback caches, corrupted RX packets will be sent up the stack
without any error markings.
Signed-off-by: Sonic Zhang <sonic.zhang@analog.com>
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We don't use this local "Mac" data anywhere (since we rely on the
netdev's storage), so punt it.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need for this to be exported since it is only used in this driver.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use netdev_* and pr_* helper funcs for output rather than printk.
Signed-off-by: Mike Frysinger <vapier@gentoo.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Helper functions for I2C and SMBus transactions don't modify the
i2c_client that is passed to them, so it can be marked const.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
The I2C specification explicitly describes both SDA and SCL as
bidirectional lines. An I2C master with a read-only SCL is thus not
compliant. If a slow slave stretches the clock, errors will happen,
so the bus can't be considered as reliable.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Use a function pointer to decide whether to call i2c_add_adapter or
i2c_add_numbered_adapter. This makes the code more compact than the
current strategy of having the common code in a separate function.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Add an i2c mux driver providing access to i2c bus segments using a
hardware MUX sitting on a master bus and controlled through gpio pins.
E.G. something like:
---------- ---------- Bus segment 1 - - - - -
| | SCL/SDA | |-------------- | |
| |------------| |
| | | | Bus segment 2 | |
| Linux | GPIO 1..N | MUX |--------------- Devices
| |------------| | | |
| | | | Bus segment M
| | | |---------------| |
---------- ---------- - - - - -
SCL/SDA of the master I2C bus is multiplexed to bus segment 1..M
according to the settings of the GPIO pins 1..N.
Signed-off-by: Peter Korsgaard <peter.korsgaard@barco.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Commit 5a0e3ad6af8660be21ca98a971cd00f331318c05 added direct inclusion
of <linux/slab.h> to those source files that appeared to need it, but
somehow missed this. On most architectures <linux/slab.h> is still
indirectly included, but there are exceptions such as alpha.
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
|
|
Commit 8a3173de inadvertently changed the ordering when
switching to hlists. Change to regular list heads so we
can use tail list adds, this improves performance.
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Put the variables accessed together in the hot-path into common
cachelines, and separate them by RW vs RO to avoid false dirtying.
We keep a local copy of the lkey and rkey in the target to avoid
traversing pointers (and associated cache lines) to find them.
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: David Dillow <dillowda@ornl.gov>
|
|
We don't need protection against the SCSI stack, so use our own lock to
allow parallel progress on separate CPUs.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
|
|
We only need the lock to cover list and credit manipulations, so push
those into srp_remove_req() and update the call chains.
We reorder the request removal and command completion in
srp_process_rsp() to avoid the SCSI mid-layer sending another command
before we've released our request and added any credits returned by the
target. This prevents us from returning HOST_BUSY unneccesarily.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out, small cleanups, and modified to avoid potential extraneous
HOST_BUSY returns by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
|
|
We only need locks to protect our lists and number of credits available.
By pre-consuming the credit for the request, we can reduce our lock
coverage to just those areas. If we don't actually send the request,
we'll need to put the credit back into the pool.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
|
|
We use req->scmnd != NULL to indicate an active request, so there's no
need to keep a separate list for them. We can afford the array iteration
during error handling, and dropping it gives us one less item that needs
lock protection.
Signed-off-by: Bart Van Assche <bvanassche@acm.org>
[ broken out and small cleanups by David Dillow ]
Signed-off-by: David Dillow <dillowda@ornl.gov>
|
|
pcmcia_request_irq() and pcmcia_enable_device() are intended
to be called from process context (first function allocate memory
with GFP_KERNEL, second take a mutex). We can not take spin lock
and call them.
It's safe to move spin lock after pcmcia_enable_device() as we
still hold off IRQ until dev->base_addr is 0 and driver will
not proceed with interrupts when is not ready.
Patch resolves:
https://bugzilla.redhat.com/show_bug.cgi?id=643758
Reported-and-tested-by: rbugz@biobind.com
Cc: stable@kernel.org # 2.6.34+
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
This is an attempt to fix a long standing open bug:
http://bugzilla.intellinuxwireless.org/show_bug.cgi?id=1334
The interrupt handler checks for INTA being -1, apparently that means that the
hardware is gone. But the interrupt handler defers actual interrupt processing
to a tasklet. By the time the tasklet is run and checks INTA again, the
hardware might be gone and INTA be -1, which confuses the driver because all
event bits are set.
The patch applies to 2.6.37.
Signed-off-by: Indan Zupancic <indan@nul.nu>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Some Broadcom based wireless devices contain dangling ethernet cores.
This triggers the ssb probing mechanism and tries to load the b44 driver
on this core.
Ignore the dangling core in the ssb core scanning code to avoid
access to the core and failure of b44 probing.
Signed-off-by: Michael Buesch <mb@bu3sch.de>
Tested-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
P54_HDR_FLAG_DATA_OUT_SEQNR is meant to tell the
firmware that "the frame's sequence number has
already been set by the application."
Whereas IEEE80211_TX_CTL_ASSIGN_SEQ is set for
frames which lack a valid sequence number and
either the driver or firmware has to assign one.
Yup, it's the exact opposite!
Cc: <stable@kernel.org>
Signed-off-by: Christian Lamparter <chunkeey@googlemail.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
|
Just create a section to collect the LED trigger
functions and add a very short description as to
what drivers should do.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: John W. Linville <linville@tuxdriver.com>
|
