| Age | Commit message (Collapse) | Author |
|---|
|
When netfilter defrag hooks are loaded (due to the presence of conntrack
rules, for example), fragmented packets entering the bridge will be
defragged by the bridge's pre-routing hook (br_nf_pre_routing() ->
ipv4_conntrack_defrag()).
Later on, in the bridge's post-routing hook, the defragged packet will
be fragmented again. If the size of the largest fragment is larger than
what the kernel has determined as the destination MTU (using
ip_skb_dst_mtu()), the defragged packet will be dropped.
Before commit ac6627a28dbf ("net: ipv4: Consolidate ipv4_mtu and
ip_dst_mtu_maybe_forward"), ip_skb_dst_mtu() would return dst_mtu() as
the destination MTU. Assuming the dst entry attached to the packet is
the bridge's fake rtable one, this would simply be the bridge's MTU (see
fake_mtu()).
However, after above mentioned commit, ip_skb_dst_mtu() ends up
returning the route's MTU stored in the dst entry's metrics. Ideally, in
case the dst entry is the bridge's fake rtable one, this should be the
bridge's MTU as the bridge takes care of updating this metric when its
MTU changes (see br_change_mtu()).
Unfortunately, the last operation is a no-op given the metrics attached
to the fake rtable entry are marked as read-only. Therefore,
ip_skb_dst_mtu() ends up returning 1500 (the initial MTU value) and
defragged packets are dropped during fragmentation when dealing with
large fragments and high MTU (e.g., 9k).
Fix by moving the fake rtable entry's metrics to be per-bridge (in a
similar fashion to the fake rtable entry itself) and marking them as
writable, thereby allowing MTU changes to be reflected.
Fixes: 62fa8a846d7d ("net: Implement read-only protection and COW'ing of metrics.")
Fixes: 33eb9873a283 ("bridge: initialize fake_rtable metrics")
Reported-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Closes: https://lore.kernel.org/netdev/PH0PR10MB4504888284FF4CBA648197D0ACB82@PH0PR10MB4504.namprd10.prod.outlook.com/
Tested-by: Venkat Venkatsubra <venkat.x.venkatsubra@oracle.com>
Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Link: https://patch.msgid.link/20250515084848.727706-1-idosch@nvidia.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The pointer arithmentic for accessing the tail tag only works
for linear skbs.
For nonlinear skbs, it reads uninitialized memory inside the
skb headroom, essentially randomizing the tag. I have observed
it gets set to 6 most of the time.
Example where ksz9477_rcv thinks that the packet from port 1 comes from port 6
(which does not exist for the ksz9896 that's in use), dropping the packet.
Debug prints added by me (not included in this patch):
[ 256.645337] ksz9477_rcv:323 tag0=6
[ 256.645349] skb len=47 headroom=78 headlen=0 tailroom=0
mac=(64,14) mac_len=14 net=(78,0) trans=78
shinfo(txflags=0 nr_frags=1 gso(size=0 type=0 segs=0))
csum(0x0 start=0 offset=0 ip_summed=0 complete_sw=0 valid=0 level=0)
hash(0x0 sw=0 l4=0) proto=0x00f8 pkttype=1 iif=3
priority=0x0 mark=0x0 alloc_cpu=0 vlan_all=0x0
encapsulation=0 inner(proto=0x0000, mac=0, net=0, trans=0)
[ 256.645377] dev name=end1 feat=0x0002e10200114bb3
[ 256.645386] skb headroom: 00000000: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 256.645395] skb headroom: 00000010: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 256.645403] skb headroom: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 256.645411] skb headroom: 00000030: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 256.645420] skb headroom: 00000040: ff ff ff ff ff ff 00 1c 19 f2 e2 db 08 06
[ 256.645428] skb frag: 00000000: 00 01 08 00 06 04 00 01 00 1c 19 f2 e2 db 0a 02
[ 256.645436] skb frag: 00000010: 00 83 00 00 00 00 00 00 0a 02 a0 2f 00 00 00 00
[ 256.645444] skb frag: 00000020: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 01
[ 256.645452] ksz_common_rcv:92 dsa_conduit_find_user returned NULL
Call skb_linearize before trying to access the tag.
This patch fixes ksz9477_rcv which is used by the ksz9896 I have at
hand, and also applies the same fix to ksz8795_rcv which seems to have
the same problem.
Signed-off-by: Jakob Unterwurzacher <jakob.unterwurzacher@cherry.de>
CC: stable@vger.kernel.org
Fixes: 016e43a26bab ("net: dsa: ksz: Add KSZ8795 tag code")
Fixes: 8b8010fb7876 ("dsa: add support for Microchip KSZ tail tagging")
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Link: https://patch.msgid.link/20250515072920.2313014-1-jakob.unterwurzacher@cherry.de
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Syzkaller reports the following issue:
BUG: sleeping function called from invalid context at kernel/locking/mutex.c:578
netdev_lock include/linux/netdevice.h:2751 [inline]
netdev_lock_ops include/net/netdev_lock.h:42 [inline]
dev_set_promiscuity+0x10e/0x260 net/core/dev_api.c:285
bond_set_promiscuity drivers/net/bonding/bond_main.c:922 [inline]
bond_change_rx_flags+0x219/0x690 drivers/net/bonding/bond_main.c:4732
dev_change_rx_flags net/core/dev.c:9145 [inline]
__dev_set_promiscuity+0x3f5/0x590 net/core/dev.c:9189
netif_set_promiscuity+0x50/0xe0 net/core/dev.c:9201
dev_set_promiscuity+0x126/0x260 net/core/dev_api.c:286
^^ all of the above is under rcu lock
team_change_rx_flags+0x1b3/0x330 drivers/net/team/team_core.c:1785
dev_change_rx_flags net/core/dev.c:9145 [inline]
__dev_set_promiscuity+0x3f5/0x590 net/core/dev.c:9189
netif_set_promiscuity+0x50/0xe0 net/core/dev.c:9201
dev_set_promiscuity+0x126/0x260 net/core/dev_api.c:286
hsr_del_port+0x25e/0x2d0 net/hsr/hsr_slave.c:233
hsr_netdev_notify+0x827/0xb60 net/hsr/hsr_main.c:104
notifier_call_chain+0x1b3/0x3e0 kernel/notifier.c:85
call_netdevice_notifiers_extack net/core/dev.c:2214 [inline]
call_netdevice_notifiers net/core/dev.c:2228 [inline]
unregister_netdevice_many_notify+0x15d8/0x2330 net/core/dev.c:11970
rtnl_delete_link net/core/rtnetlink.c:3522 [inline]
rtnl_dellink+0x488/0x710 net/core/rtnetlink.c:3564
rtnetlink_rcv_msg+0x7cc/0xb70 net/core/rtnetlink.c:6955
netlink_rcv_skb+0x219/0x490 net/netlink/af_netlink.c:2534
netlink_unicast_kernel net/netlink/af_netlink.c:1313 [inline]
netlink_unicast+0x758/0x8d0 net/netlink/af_netlink.c:1339
netlink_sendmsg+0x805/0xb30 net/netlink/af_netlink.c:1883
team_change_rx_flags runs under rcu lock which means we can't grab
instance lock for the lower devices. Switch to team->lock, similar
to what we already do for team_set_mac_address and team_change_mtu.
Fixes: 78cd408356fe ("net: add missing instance lock to dev_set_promiscuity")
Reported-by: syzbot+53485086a41dbb43270a@syzkaller.appspotmail.com
Closes: https://syzkaller.appspot.com/bug?extid=53485086a41dbb43270a
Link: https://lore.kernel.org/netdev/6822cc81.050a0220.f2294.00e8.GAE@google.com
Signed-off-by: Stanislav Fomichev <stfomichev@gmail.com>
Link: https://patch.msgid.link/20250514220319.3505158-1-stfomichev@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The debugfs summary output could access uninitialized elements in
the freq_in[] and signal_out[] arrays, causing NULL pointer
dereferences and triggering a kernel Oops (page_fault_oops).
This patch adds u8 fields (nr_freq_in, nr_signal_out) to track the
number of initialized elements, with a maximum of 4 per array.
The summary output functions are updated to respect these limits,
preventing out-of-bounds access and ensuring safe array handling.
Widen the label variables because the change confuses GCC about
max length of the strings.
Fixes: ef61f5528fca ("ptp: ocp: add Adva timecard support")
Signed-off-by: Sagi Maimon <maimon.sagi@gmail.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Reviewed-by: Vadim Fedorenko <vadim.fedorenko@linux.dev>
Link: https://patch.msgid.link/20250514073541.35817-1-maimon.sagi@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Pull NFS client bugfixes from Trond Myklebust:
- NFS: Fix a couple of missed handlers for the ENETDOWN and ENETUNREACH
transport errors
- NFS: Handle Oopsable failure of nfs_get_lock_context in the unlock
path
- NFSv4: Fix a race in nfs_local_open_fh()
- NFSv4/pNFS: Fix a couple of layout segment leaks in layoutreturn
- NFSv4/pNFS Avoid sharing pNFS DS connections between net namespaces
since IP addresses are not guaranteed to refer to the same nodes
- NFS: Don't flush file data while holding multiple directory locks in
nfs_rename()
* tag 'nfs-for-6.15-2' of git://git.linux-nfs.org/projects/trondmy/linux-nfs:
NFS: Avoid flushing data while holding directory locks in nfs_rename()
NFS/pnfs: Fix the error path in pnfs_layoutreturn_retry_later_locked()
NFSv4/pnfs: Reset the layout state after a layoutreturn
NFS/localio: Fix a race in nfs_local_open_fh()
nfs: nfs3acl: drop useless assignment in nfs3_get_acl()
nfs: direct: drop useless initializer in nfs_direct_write_completion()
nfs: move the nfs4_data_server_cache into struct nfs_net
nfs: don't share pNFS DS connections between net namespaces
nfs: handle failure of nfs_get_lock_context in unlock path
pNFS/flexfiles: Record the RPC errors in the I/O tracepoints
NFSv4/pnfs: Layoutreturn on close must handle fatal networking errors
NFSv4: Handle fatal ENETDOWN and ENETUNREACH errors
|
|
The Linux client assumes that all filehandles are non-volatile for
renames within the same directory (otherwise sillyrename cannot work).
However, the existence of the Linux 'subtree_check' export option has
meant that nfs_rename() has always assumed it needs to flush writes
before attempting to rename.
Since NFSv4 does allow the client to query whether or not the server
exhibits this behaviour, and since knfsd does actually set the
appropriate flag when 'subtree_check' is enabled on an export, it
should be OK to optimise away the write flushing behaviour in the cases
where it is clearly not needed.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
Reviewed-by: Jeff Layton <jlayton@kernel.org>
|
|
If there isn't a valid layout, or the layout stateid has changed, the
cleanup after a layout return should clear out the old data.
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
If there are still layout segments in the layout plh_return_lsegs list
after a layout return, we should be resetting the state to ensure they
eventually get returned as well.
Fixes: 68f744797edd ("pNFS: Do not free layout segments that are marked for return")
Signed-off-by: Trond Myklebust <trond.myklebust@hammerspace.com>
|
|
`pr_cont()` unfortunately does not work here, as other parts of the
Linux kernel log between the two log lines:
[18445.295056] r8152-cfgselector 4-1.1.3: USB disconnect, device number 5
[18445.295112] OOM killer enabled.
[18445.295115] Restarting tasks ...
[18445.295185] usb 3-1: USB disconnect, device number 2
[18445.295193] usb 3-1.1: USB disconnect, device number 3
[18445.296262] usb 3-1.5: USB disconnect, device number 4
[18445.297017] done.
[18445.297029] random: crng reseeded on system resumption
`pr_cont()` also uses the default log level, normally warning, if the
corresponding log line is interrupted.
Therefore, replace the `pr_cont()`, and explicitly log it as a separate
line with log level info:
Restarting tasks: Starting
[…]
Restarting tasks: Done
Signed-off-by: Paul Menzel <pmenzel@molgen.mpg.de>
Link: https://patch.msgid.link/20250511174648.950430-1-pmenzel@molgen.mpg.de
[ rjw: Rebase on top of an earlier analogous change ]
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux
Merge cpupower utility update for 6.16 from Shuah Khan:
"Adds systemd service to run cpupower and changes binding's makefile
to use -lcpupower.
cpupower: add a systemd service to run cpupower
cpupower: do not write DESTDIR to cpupower.service
cpupower: do not call systemctl at install time
cpupower: do not install files to /etc/default/
cpupower: change binding's makefile to use -lcpupower"
* tag 'linux-cpupower-6.16-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/shuah/linux:
cpupower: do not install files to /etc/default/
cpupower: do not call systemctl at install time
cpupower: do not write DESTDIR to cpupower.service
cpupower: change binding's makefile to use -lcpupower
cpupower: add a systemd service to run cpupower
|
|
pm_runtime_put_autosuspend() schedules a hrtimer to expire
at "dev->power.timer_expires". If the hrtimer's callback,
pm_suspend_timer_fn(), observes that the current time equals
"dev->power.timer_expires", it unexpectedly bails out instead of
proceeding with runtime suspend.
pm_suspend_timer_fn():
if (expires > 0 && expires < ktime_get_mono_fast_ns()) {
dev->power.timer_expires = 0;
rpm_suspend(..)
}
Additionally, as ->timer_expires is not cleared, all the future auto
suspend requests will not schedule hrtimer to perform auto suspend.
rpm_suspend():
if ((rpmflags & RPM_AUTO) &&...) {
if (!(dev->power.timer_expires && ...) { <-- this will fail.
hrtimer_start_range_ns(&dev->power.suspend_timer,...);
}
}
Fix this by as well checking if current time reaches the set expiration.
Co-developed-by: Patrick Daly <quic_pdaly@quicinc.com>
Signed-off-by: Patrick Daly <quic_pdaly@quicinc.com>
Signed-off-by: Charan Teja Kalla <quic_charante@quicinc.com>
Link: https://patch.msgid.link/20250515064125.1211561-1-quic_charante@quicinc.com
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
Tegra PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-10-maz@kernel.org
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
XGENE PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-9-maz@kernel.org
|
|
In an effort to move ARM64 away from the legacy MSI setup, convert the
Apple PCIe driver to the MSI-parent infrastructure and let each device have
its own MSI domain.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Alyssa Rosenzweig <alyssa@rosenzweig.io>
Link: https://lore.kernel.org/all/20250513172819.2216709-8-maz@kernel.org
|
|
Bad MSI implementations multiplex MSIs onto a single downstream interrupt,
meaning they have no concept of individual affinity.
The old MSI code did a reasonable job at this by honouring the
MSI_FLAG_NO_AFFINITY, but the new shiny device MSI code doesn't.
Teach it about the sad reality of existing hardware.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-7-maz@kernel.org
|
|
Switch the MVEBU family of interrupt chip drivers over to the common helper
function to create the interrupt domains.
[ tglx: Moved the struct out of the function call argument and fix up
the of_node_to_fwnode() instances ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-5-maz@kernel.org
|
|
Switch the GIC family of interrupt chip drivers over to the common helper
function to create the interrupt domains.
[ tglx: Moved the struct out of the function call argument ]
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-4-maz@kernel.org
|
|
Creating an irq domain that serves as an MSI parent requires
a substantial amount of esoteric boiler-plate code, some of
which is often provided twice (such as the bus token).
To make things a bit simpler for the unsuspecting MSI tinkerer,
provide a helper that does it for them, and serves as documentation
of what needs to be provided.
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-3-maz@kernel.org
|
|
Move irq-msi-lib.h into include/linux/irqchip, making it available
to compilation units outside of drivers/irqchip.
This requires some churn in drivers to fetch it from the new location,
generated using this script:
git grep -l -w \"irq-msi-lib.h\" | \
xargs sed -i -e 's:"irq-msi-lib.h":\<linux/irqchip/irq-msi-lib.h\>:'
Signed-off-by: Marc Zyngier <maz@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250513172819.2216709-2-maz@kernel.org
|
|
Pick up the PCI changes to avoid conflicts.
|
|
Now that the file has been thrown through the mincer, finish the job and
consolidate the coding style.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
irqdomain.c's kernel-doc exists, but is not plugged into Documentation/
yet.
Before plugging it in, fix it first: irq_domain_get_irq_data() and
irq_domain_set_info() were documented twice. Identically, by both
definitions for CONFIG_IRQ_DOMAIN_HIERARCHY and !CONFIG_IRQ_DOMAIN_HIERARCHY.
Therefore, switch the second kernel-doc into an ordinary comment -- change
"/**" to simple "/*". This avoids sphinx's: WARNING: Duplicate C
declaration
Next, in commit b7b377332b96 ("irqdomain: Fix the kernel-doc and plug it
into Documentation"), irqdomain.h's (header) kernel-doc was added into
core-api/genericirq.rst. But given the amount of irqdomain functions and
structures, move all these to core-api/irq/irq-domain.rst now.
Finally, add these newly fixed irqdomain.c's (source) docs there as
well.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-58-jirislaby@kernel.org
|
|
The irqdomain documentaion became obsolete over time. Update and extend
it a bit with respect to the current code and HW.
Most notably the doubled documentation of irq_domain (from .rst and .h)
was unified and let only in .rst. A reference link was added to .h.
Furthermore:
* Add some 'struct' keywords, so that the respective structs are
hyperlinked
* :c:member: use where appropriate to mark a member of a struct
* Rephrase some wording to improve readability/understanding
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-57-jirislaby@kernel.org
|
|
The improvements include:
* Capitals in headlines.
* Add commas: for easier reading, it is always desired to add commas
at some places in text. Like before adverbs or after fronted
sentences.
* 3rd person -> add 's' to verbs.
* End some sentences with period and start a new one. Avoid thus heavy
sentences.
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-56-jirislaby@kernel.org
|
|
Just note in the docs:
1) A PCI device as an example for shared interrupts
2) A sparse tree can be used for interrupts too
3) i8259s which have 8 pins
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-55-jirislaby@kernel.org
|
|
For easier reading, it is always desired to add commas at some places in
text. Like before adverbs or after fronted sentences.
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-54-jirislaby@kernel.org
|
|
Many of irqdomain.h's functions are referenced in Documentation/ but are
not properly documented. Therefore, document these.
And use "Returns:" tag consistently, so that it is properly generated in
the resulting docs.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-53-jirislaby@kernel.org
|
|
This is just expressing it explicitly as irq_domain_instantiate() takes
const already. No functional change.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-52-jirislaby@kernel.org
|
|
This makes the code more compact.
Note that irq_domain_create_hierarchy()'s handling of size is now part of
info's initializer (using the ternary operator). That makes more sense
while reading it.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-51-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated and unused now. So remove it.
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-50-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/all/20250319092951.37667-48-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-47-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-45-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/all/20250319092951.37667-44-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-43-jirislaby@kernel.org
|
|
irq_linear_revmap() is deprecated, so remove all its uses and supersede
them by an identical call to irq_find_mapping().
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> # for 8xx
Link: https://lore.kernel.org/all/20250319092951.37667-42-jirislaby@kernel.org
|
|
Most irq_domain_add_*() functions are unused now, so drop them. The
remaining ones are moved to the deprecated section and will be removed
during the merge window after the patches in various trees have been
merged.
Note: The Chinese docs are touched but unfinished. I cannot parse those.
[ tglx: Remove the leftover in irq-domain.rst and handle merge logistics ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-41-jirislaby@kernel.org
|
|
All irq_domain_add_*() functions are going away. PowerPC is the only
user of irq_domain_add_nomap() and there is no irq_domain_create_nomap()
complement.
Therefore, to align with the rest of the kernel, rename
irq_domain_add_nomap() to irq_domain_create_nomap() and accept a
fwnode_handle instead of a device_node.
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-40-jirislaby@kernel.org
|
|
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fixed up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-39-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Acked-by: Christophe Leroy <christophe.leroy@csgroup.eu> # For soc/fsl
Link: https://lore.kernel.org/all/20250319092951.37667-35-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-34-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Christophe Leroy <christophe.leroy@csgroup.eu> # For 8xx
Link: https://lore.kernel.org/all/20250319092951.37667-33-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/all/20250319092951.37667-31-jirislaby@kernel.org
|
|
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix and convert the new instance in
dwc/pcie-amd-mdb.c ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-30-jirislaby@kernel.org
|
|
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-29-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-28-jirislaby@kernel.org
|
|
irq_domain_add_simple() is going away as being obsolete now. Switch to
the preferred irq_domain_create_simple(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-27-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-26-jirislaby@kernel.org
|
|
irq_domain_add_*() interfaces are going away as being obsolete now.
Switch to the preferred irq_domain_create_*() ones. Those differ in the
node parameter: They take more generic struct fwnode_handle instead of
struct device_node. Therefore, of_fwnode_handle() is added around the
original parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-25-jirislaby@kernel.org
|
|
irq_domain_add_linear() is going away as being obsolete now. Switch to
the preferred irq_domain_create_linear(). That differs in the first
parameter: It takes more generic struct fwnode_handle instead of struct
device_node. Therefore, of_fwnode_handle() is added around the
parameter.
Note some of the users can likely use dev->fwnode directly instead of
indirect of_fwnode_handle(dev->of_node). But dev->fwnode is not
guaranteed to be set for all, so this has to be investigated on case to
case basis (by people who can actually test with the HW).
[ tglx: Fix up subject prefix ]
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/all/20250319092951.37667-24-jirislaby@kernel.org
|
