summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2015-04-08gpio: removing kfree remove functionalityVarka Bhadram
commit 3de07e5aaf290a0b58919 ("drivers: gpio: use devm_kzalloc") introduce devm_kzalloc() for allocating the memory. In this case kfree is not required to use. Above commit id introduced the bug that kfree is not removed from the remove function. This patch fix the above bug. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: mvebu: Fix mask/unmask managment per irq chip typeGregory CLEMENT
Level IRQ handlers and edge IRQ handler are managed by tow different sets of registers. But currently the driver uses the same mask for the both registers. It lead to issues with the following scenario: First, an IRQ is requested on a GPIO to be triggered on front. After, this an other IRQ is requested for a GPIO of the same bank but triggered on level. Then the first one will be also setup to be triggered on level. It leads to an interrupt storm. The different kind of handler are already associated with two different irq chip type. With this patch the driver uses a private mask for each one which solves this issue. It has been tested on an Armada XP based board and on an Armada 375 board. For the both boards, with this patch is applied, there is no such interrupt storm when running the previous scenario. This bug was already fixed but in a different way in the legacy version of this driver by Evgeniy Dushistov: 9ece8839b1277fb9128ff6833411614ab6c88d68 "ARM: orion: Fix for certain sequence of request_irq can cause irq storm". The fact the new version of the gpio drive could be affected had been discussed there: http://thread.gmane.org/gmane.linux.ports.arm.kernel/344670/focus=364012 Reported-by: Evgeniy A. Dushistov <dushistov@mail.ru> Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com> Cc: <stable@vger.kernel.org> # v3.7 + Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: split GPIO drivers in submenusLinus Walleij
Create Kconfig submenus for memory mapped, I2C, MFD, PCI, SPI and USB GPIO drivers to help navigate the forest of drivers in this subsystem. The I2C, SPI and USB menus get dependencies so we don't have to see them unless we have the required subsystem enabled in the first place. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: move MFD GPIO drivers under their own commentLinus Walleij
Get rid of AC97, MODULbus and other weird subheadings for GPIO drivers. Move all MFD drivers out of I2C etc and in under the MFD comment. This is too weird as it is and makes no sense, if the dependent parent driver is MFD, group these as MFD GPIO drivers. Alphabetize and move this comment group inbetween "I2C" and "PCI" to also have the groups in alphabetic order. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: move BCM Kona Kconfig optionLinus Walleij
Move the Kconfig option for the Broadcom BCM Kona up to the commin GPIO controllers, as it is currently grouped under MODULbus expanders which it definately is not. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: arrange SPI Kconfig symbols alphabeticallyLinus Walleij
Rearrange the SPI GPIO expanders in alphabetic order as already indicated by the comment in the file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: arrange PCI GPIO controllers alphabeticallyLinus Walleij
Rearrange PCI GPIO controllers in alphabetic order as already indicated by the comment in the file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: arrange I2C Kconfig symbols alphabeticallyLinus Walleij
Rearrange the I2C GPIO expanders in alphabetic order as already indicated by the comment in the file. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: arrange Kconfig symbols alphabeticallyLinus Walleij
This rearranges the GPIO drivers Kconfig symbols alphabetically as the top comment in the file already states they should be. No functional changes whatsoever. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: ich: Implement get_direction functionAaron Sierra
Allow the kernel to query the driver for a GPIO's pin direction. Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: use (!foo) instead of (foo == NULL)Varka Bhadram
Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: arizona: drop owner assignment from platform_driversVarka Bhadram
This driver no need to set the owner field, it will be populated by driver core. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: max7300: remove 'ret' variableVarka Bhadram
Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: use devm_kzallocVarka Bhadram
We can use devres API for allocating memory. No need of using kfree. Signed-off-by: Varka Bhadram <varkab@cdac.in> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: sch: use uapi/linux/pci_ids.h directlyMichael S. Tsirkin
Header moved from linux/pci_ids.h to uapi/linux/pci_ids.h, use the new header directly so we can drop the wrapper in include/linux/pci_ids.h. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: x-gene: fix devm_ioremap_resource() checkVladimir Zapolskiy
devm_ioremap_resource() returns IOMEM_ERR_PTR() and it never returns NULL, fix the check to prevent access to invalid virtual address. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-08gpio: loongson: Add Loongson-3A/3B GPIO driver supportHuacai Chen
Improve Loongson-2's GPIO driver to support Loongson-3A/3B, and update Loongson-3's default config file. Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-07MIPS: Move Loongson GPIO driver to drivers/gpioHuacai Chen
Move Loongson-2's GPIO driver to drivers/gpio and add Kconfig options. Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-04-07MIPS: Cleanup Loongson-2F's gpio driverHuacai Chen
This cleanup is prepare to move the driver to drivers/gpio. Custom definitions of gpio_get_value()/gpio_set_value() are dropped. Acked-by: Ralf Baechle <ralf@linux-mips.org> Signed-off-by: Huacai Chen <chenhc@lemote.com> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: gpio-tb10x: remove incorrect __exit markupDmitry Torokhov
Even if bus is not hot-pluggable, the devices can be unbound from the driver via sysfs, so we should not be using __exit annotations on remove() methods. The only exception is drivers registered with platform_driver_probe() which specifically disables sysfs bind/unbind attributes. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: get rid of GPIO_INDEX() macroGrygorii Strashko
Now OMAP GPIO driver prepared for GPIO_INDEX() macro removing. Do It ;) Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: get rid of omap_irq_to_gpio()Grygorii Strashko
Now OMAP GPIO driver prepared for omap_irq_to_gpio() removing. Do it ;) Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: get rid of GPIO_BIT() macroGrygorii Strashko
Now OMAP GPIO driver prepared for GPIO_BIT() macro removing. Do it ;) Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: convert gpio irq functions to use GPIO offsetGrygorii Strashko
Convert GPIO IRQ functions to use GPIO offset instead of system GPIO numbers. This allows to drop unneeded conversations between system GPIO <-> GPIO offset which are done in many places and many times. It is safe to do now because: - gpiolib always passes GPIO offset to GPIO controller - OMAP GPIO driver converted to use IRQ domain, so struct irq_data->hwirq contains GPIO offset This is preparation step before removing: #define GPIO_INDEX(bank, gpio) #define GPIO_BIT(bank, gpio) int omap_irq_to_gpio() Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: drop 'gpio' param from omap_gpio_init_irq()Grygorii Strashko
The 'gpio' parameter isn't needed any more as it duplicates 'offset' parameter, so drop it. Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: convert debounce functions switch to use gpio offsetGrygorii Strashko
Convert debounce functions to use GPIO offset instead of system GPIO numbers. This allows to drop unneeded conversations between system GPIO <-> GPIO offset which are done in many places and many times. It is safe to do now because: - gpiolib always passes GPIO offset to GPIO controller - OMAP GPIO driver converted to use IRQ domain This is preparation step before removing: #define GPIO_INDEX(bank, gpio) #define GPIO_BIT(bank, gpio) int omap_irq_to_gpio() Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: simplify omap_set_gpio_dataout_x()Grygorii Strashko
Both functions omap_set_gpio_dataout_reg() and omap_set_gpio_dataout_mask() accept GPIO offset as 'gpio' input parameter, so rename it to 'offset' and drop usage of GPIO_BIT() macro. Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27gpio: omap: convert omap_gpio_is_input() to use gpio offsetGrygorii Strashko
Convert omap_gpio_is_input() to use GPIO offset instead of mask and, in such way, make code simpler and remove few lines of code. Tested-by: Tony Lindgren <tony@atomide.com> Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi> Acked-by: Santosh Shilimkar <ssantosh@kernel.org> Acked-by: Javier Martinez Canillas <javier@dowhile0.org> Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-27altera_gpio_probe() can be statickbuild test robot
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Prevent module clock disable when wake-up is enabledGeert Uytterhoeven
When the GPIO module is needed for wake-up, it's module clock must not be disabled. Hence implement irq_chip.irq_set_wake(), which increments/decrements the clock's enable_count when needed, and forwards the wake-up state to the upstream interrupt controller. This fixes wake-up from s2ram using gpio-keys when using a PM Domain to manage the module clock. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Add more register documentationGeert Uytterhoeven
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio: rcar: Use local variable gpio_chip in gpio_rcar_probe()Geert Uytterhoeven
The existing variable gpio_chip already points to the gpiochip instance, hence use it everywhere. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-26gpio/crystalcove: Add additional GPIO for Panel controlShobhit Kumar
Export PANEL_EN/DISABLE (offset 0x52) as additional GPIO. Needed by display driver to enable the DSI panel on BYT platform where the Panel EN/Disable control is routed thorugh CRC PMIC CC: Samuel Ortiz <sameo@linux.intel.com> Cc: Linus Walleij <linus.walleij@linaro.org> Cc: Alexandre Courbot <gnurou@gmail.com> Cc: Thierry Reding <thierry.reding@gmail.com> Acked-by: Daniel Vetter <daniel@ffwll.ch> Signed-off-by: Shobhit Kumar <shobhit.kumar@intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-19gpio: dwapb: enable for QuarkAndy Shevchenko
The Intel Quark SoC contains the DW GPIO on board. While fixing the build error the commit 1972c97db5b0 (gpio: dwapb: fix compile errors) disables the possibility to build the driver on X86, i.e. Intel Quark. The patch reenables it for Intel Quark as well. Since we have Intel Quark SoC introduced in 4.0-rc1 I would like to make this fix available there as well, though the actual MFD driver [1] is applied only for next version. [1] https://lkml.org/lkml/2015/2/1/217 Fixes: 1972c97db5b0 (gpio: dwapb: fix compile errors) Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-19gpio / ACPI: Use local variable instead of ACPI_HANDLE()Rafael J. Wysocki
In acpi_gpiochip_request_interrupts() the handle local variable already contains the value that we want to pass to acpi_walk_resources(), so it is better to use that variable instead of evaluating ACPI_HANDLE() once more for the same device. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-19gpio / ACPI: Avoid unnecessary checks in __gpiod_get_index()Rafael J. Wysocki
If dev is NULL in __gpiod_get_index() and both ACPI and OF are enabled, it will be checked twice before the code decides to give up with DT/ACPI lookup, so avoid that. Also use the observation that ACPI_COMPANION() is much more efficient than ACPI_HANDLE(), because the latter uses the former and carries out a check and a pointer dereference on top of it, so replace the ACPI_HANDLE() check with an ACPI_COMPANION() one which does not require the additional IS_ENABLED(CONFIG_ACPI) check too. Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org> Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-19gpio: move pincontrol calls to <linux/gpio/driver.h>Linus Walleij
These functions do not belong in <asm-generic/gpio.h> since the split into separate GPIO headers under <linux/gpio/*>. Move them to <linux/gpio/driver.h> as is apropriate. Acked-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-17gpio: f7188x: add GPIO support for F71869AAndreas Bofjall
Add support for the GPIOs found on the Fintek SuperI/O chip F71869A, such as the one found on the Jetway JNF99-525 motherboard, to the f7188x gpio driver. Signed-off-by: Andreas Bofjall <andreas@gazonk.org> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-17gpio: f7188x: add GPIO support for F71869Andreas Bofjall
Add support for the GPIOs found on the Fintek SuperI/O chip F71869, such as the one found on the Jetway NF96u-525 motherboard, to the f7188x gpio driver. Signed-off-by: Andreas Bofjall <andreas@gazonk.org> Tested-by: Les Schaffer <schaffer@optonline.net> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-17gpio: f7188x: correct spelling of "Fintek"Andreas Bofjall
The company is called "Fintek", not "Fintech". Fix it. Signed-off-by: Andreas Bofjall <andreas@gazonk.org> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-17gpio: fix constconst in devresLinus Walleij
Commit 1feb57a245a4910b03202a814ffc51a900bd4aca "gpio: add parameter to allow the use named gpios" includes a double-consted array. What we want is not const const * but const * const (const pointer to const data). Fix this. Reported-by: Dan Carpenter <dan.carpenter@oracle.com> Cc: Olliver Schinagl <oliver@schinagl.nl> Cc: Rojhalat Ibrahim <imr@rtschenk.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09gpio: omap: irq_shutdown: remove unnecessary call of gpiochip_unlock_as_irqGrygorii Strashko
GPIOLib core implemnts irqchip->irq_request/release_resources callbacks internally and these callbacks already contain clalls of gpiochip_lock/unlock_as_irq(). Hence, remove unnecessary call of gpiochip_unlock_as_irq() from omap_gpio_irq_shutdown(). Signed-off-by: Grygorii Strashko <grygorii.strashko@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09extend documentation for gpiod_set_array() functionsRojhalat Ibrahim
Extend the documentation for the gpiod_set_array() functions and elaborate a bit on possible use cases. Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09gpio: mrvl: documentation: trivial: fix typoJosh Wu
fix typo in the document. Signed-off-by: Josh Wu <josh.wu@atmel.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09gpio: pxa: simplify BANK_OFF macro offset calculationRob Herring
The macro BANK_OFF which calculates the base offset for each GPIO port. The macro is needlessly complex and unreadable. Simplify the calculation to a simple math operation. Signed-off-by: Rob Herring <robh@kernel.org> Cc: linux-gpio@vger.kernel.org Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-09gpio: dwapb: re-enable GPIO_DWAPB for arm64Kefeng Wang
Hisilicon arm64 soc uses designWare gpio, re-enable it after commit 1972c97db5b(gpio: dwapb: fix compile errors). Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-07drivers/gpio: Altera soft IP GPIO driver device tree bindingTien Hock Loh
Adds a new driver device tree binding for Altera soft GPIO IP Signed-off-by: Tien Hock Loh <thloh@altera.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-07drivers/gpio: Altera soft IP GPIO driverTien Hock Loh
Adds a new driver for Altera soft GPIO IP. The driver is able to do read/write and allows GPIO to be a interrupt controller. Tested on Altera GHRD on interrupt handling and IO. v10: - Updated conflicting device tree parameters - Removed unused headers - Used macro instead of magic numbers for ngpio - Code readability cleanup using ?: and temporal variables - Removed leftover garbage and unnecessary function calls - Checked bgpio_init but unusable because Altera GPIO may not be a multiple of 8 bits v9: - Removed duplicated initialization on set_type using temporals to improve code readability in calling generic_handle_irq - Using ?: ternary to reduce code size v8: - Using for_each_set_bit - Added const for struct definition - Removed naggy pr_err - Sort alpha header - Remove unused macros - Use fixed width data types instead of unsigned long - Whitespace issue fixes - Removed _relaxed function for better compatibility across different CPU - Changed irq_create_mapping to platform_get_irq updated implementation to use gpiochip_irqchip_add - Reserve interrupt-cells number 2 in device tree binding for future use - Remove confusing sections on devicetree bindings - Added tristate Kconfig help text v7: - Used dev_warn instead of pr_warn - Clean up unnecesarry if else indentation v6: - Added irq_startup and irq_shutdown - Changed bitwise clamping style - Cleanup bitwise operation to improve readability change naming of mapped irqs from virq to mapped_irq v5: - Dispose irq_domain mapping correctly - Update optional binding description in binding docs v4: - Added vendor prefix to devicetree binding for IP specific properties using MMIO GPIO helper library instead of manually map PIO to memory - altera_gpio_chip inline struct documentation to kerneldoc - Using dev_ print to print a better failure message v2, v3: - Do not reference NO_IRQ - Updated irq_set_type to only allow the hardware configured irq type Signed-off-by: Tien Hock Loh <thloh@altera.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-06gpio: vf610: Replaces comma between expression statements by semicolonAxel Lin
Signed-off-by: Axel Lin <axel.lin@ingics.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2015-03-05gpiolib: add devm_gpiod_get_array and devm_gpiod_put_array functionsRojhalat Ibrahim
Add device managed variants of gpiod_get_array() / gpiod_put_array() functions for conveniently obtaining and disposing of an entire array of GPIOs with one function call. Signed-off-by: Rojhalat Ibrahim <imr@rtschenk.de> Reviewed-by: Alexandre Courbot <acourbot@nvidia.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
generated by cgit (git 2.34.1) at 2025-09-07 07:55:12 +0000