| Age | Commit message (Collapse) | Author |
|---|
|
When doing RX batch packet processing, we currently always repeat
the route lookup for each ingress packet. When no custom rules are
in place, and there aren't routes depending on source addresses,
we know that packets with the same destination address will use
the same dst.
This change tries to avoid per packet route lookup caching
the destination address of the latest successful lookup, and
reusing it for the next packet when the above conditions are
in place. Ingress traffic for most servers should fit.
The measured performance delta under UDP flood vs a recvmmsg
receiver is as follow:
vanilla patched delta
Kpps Kpps %
1431 1674 +17
In the worst-case scenario - each packet has a different
destination address - the performance delta is within noise
range.
v3 -> v4:
- support hints for SUBFLOW build, too (David A.)
- several style fixes (Eric)
v2 -> v3:
- add fib6_has_custom_rules() helpers (David A.)
- add ip6_extract_route_hint() helper (Edward C.)
- use hint directly in ip6_list_rcv_finish() (Willem)
v1 -> v2:
- fix build issue with !CONFIG_IPV6_MULTIPLE_TABLES
- fix potential race when fib6_has_custom_rules is set
while processing a packet batch
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use a per namespace counter, increment it on successful creation
of any route using the source address, decrement it on deletion
of such routes.
This allows us to check easily if the routing decision in the
current namespace depends on the packet source. Will be used
by the next patch.
Suggested-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It wraps the namespace field with the same name, to easily
access it regardless of build options.
Suggested-by: David Ahern <dsahern@gmail.com>
Suggested-by: Eric Dumazet <eric.dumazet@gmail.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Yangbo Lu says:
====================
Support PTP clock and hardware timestamping for DSA Felix driver
This patch-set is to support PTP clock and hardware timestamping
for DSA Felix driver. Some functions in ocelot.c/ocelot_board.c
driver were reworked/exported, so that DSA Felix driver was able
to reuse them as much as possible.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to reuse ocelot functions as possible to enable PTP
clock and to support hardware timestamping on Felix.
On TX path, timestamping works on packet which requires timestamp.
The injection header will be configured accordingly, and skb clone
requires timestamp will be added into a list. The TX timestamp
is final handled in threaded interrupt handler when PTP timestamp
FIFO is ready.
On RX path, timestamping is always working. The RX timestamp could
be got from extraction header.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to define PTP registers for felix_vsc9959.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert to use ocelot_port_add_txtstamp_skb() for adding skbs which
require TX timestamp into list. Export it so that DSA Felix driver
could reuse it too.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The method getting TX timestamp by reading timestamp FIFO and
matching skbs list is common for DSA Felix driver too.
So move code out of ocelot_board.c, convert to use
ocelot_get_txtstamp() function and export it.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Export ocelot_hwstamp_get/set functions so that DSA driver
is able to reuse them.
Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Report from Dan Carpenter,
net/core/skmsg.c:792 sk_psock_write_space()
error: we previously assumed 'psock' could be null (see line 790)
net/core/skmsg.c
789 psock = sk_psock(sk);
790 if (likely(psock && sk_psock_test_state(psock, SK_PSOCK_TX_ENABLED)))
Check for NULL
791 schedule_work(&psock->work);
792 write_space = psock->saved_write_space;
^^^^^^^^^^^^^^^^^^^^^^^^
793 rcu_read_unlock();
794 write_space(sk);
Ensure psock dereference on line 792 only occurs if psock is not null.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Fixes: 604326b41a6f ("bpf, sockmap: convert to generic sk_msg interface")
Signed-off-by: John Fastabend <john.fastabend@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fix from Will Deacon:
"Ensure PAN is re-enabled following user fault in uaccess routines.
After I thought we were done for 5.4, we had a report this week of a
nasty issue that has been shown to leak data between different user
address spaces thanks to corruption of entries in the TLB. In
hindsight, we should have spotted this in review when the PAN code was
merged back in v4.3, but hindsight is 20/20 and I'm trying not to beat
myself up too much about it despite being fairly miserable.
Anyway, the fix is "obvious" but the actual failure is more more
subtle, and is described in the commit message. I've included a fairly
mechanical follow-up patch here as well, which moves this checking out
into the C wrappers which is what we do for {get,put}_user() already
and allows us to remove these bloody assembly macros entirely. The
patches have passed kernelci [1] [2] [3] and CKI [4] tests over night,
as well as some targetted testing [5] for this particular issue.
The first patch is tagged for stable and should be applied to 4.14,
4.19 and 5.3. I have separate backports for 4.4 and 4.9, which I'll
send out once this has landed in your tree (although the original
patch applies cleanly, it won't build for those two trees).
Thanks to Pavel Tatashin for reporting this and Mark Rutland for
helping to diagnose the issue and review/test the solution"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64: uaccess: Remove uaccess_*_not_uao asm macros
arm64: uaccess: Ensure PAN is re-enabled after unhandled uaccess fault
|
|
The 0-DAY found that audit_log_task is not declared under
CONFIG_AUDITSYSCALL which causes compilation error when
it is not defined:
kernel/bpf/syscall.o: In function `bpf_audit_prog.isra.30':
>> syscall.c:(.text+0x860): undefined reference to `audit_log_task'
Adding the audit_log_task declaration and stub within
CONFIG_AUDITSYSCALL ifdef.
Fixes: 91e6015b082b ("bpf: Emit audit messages upon successful prog load and unload")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Jiri Olsa <jolsa@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The workqueue only exists for the primary PF. For other functions
we hit a WARN_ON in kernel/workqueue.c.
Fixes: 7c236c43b838 ("sfc: Add support for IEEE-1588 PTP")
Signed-off-by: Martin Habets <mhabets@solarflare.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull block fix from Jens Axboe:
"Just a single fix for an issue in nbd introduced in this cycle"
* tag 'for-linus-20191121' of git://git.kernel.dk/linux-block:
nbd:fix memory leak in nbd_get_socket()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"A last set of small fixes for GPIO, this cycle was quite busy.
- Fix debounce delays on the MAX77620 GPIO expander
- Use the correct unit for debounce times on the BD70528 GPIO expander
- Get proper deps for parallel builds of the GPIO tools
- Add a specific ACPI quirk for the Terra Pad 1061"
* tag 'gpio-v5.4-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpiolib: acpi: Add Terra Pad 1061 to the run_edge_events_on_boot_blacklist
tools: gpio: Correctly add make dependencies for gpio_utils
gpio: bd70528: Use correct unit for debounce times
gpio: max77620: Fixup debounce delays
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style. This fixes various indentation mixups (seven spaces,
tab+one space, etc).
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fixlet from Christian Brauner:
"This contains a simple fix for the pidfd poll method. In the original
patchset pidfd_poll() was made to return an unsigned int. However, the
poll method is defined to return a __poll_t. While the unsigned int is
not a huge deal it's just nicer to return a __poll_t.
I've decided to send it right before the 5.4 release mainly so that
stable doesn't need to backport it to both 5.4 and 5.3"
* tag 'for-linus-2019-11-21' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: fix pidfd_poll()'s return type
|
|
If starting the transfer of a command suceeds but the transfer for the reply
fails, it is not enough to initiate killing the transfer for the
command may still be running. You need to wait for the killing to finish
before you can reuse URB and buffer.
Reported-and-tested-by: syzbot+711468aa5c3a1eabf863@syzkaller.appspotmail.com
Signed-off-by: Oliver Neukum <oneukum@suse.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As Jakub suggested on another patch, it's better to do the check
on erspan options before allocating memory.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
LWTUNNEL_IP(6)_OPTS are the new items in ip(6)_tun_policy, which
are parsed by nla_parse_nested_deprecated(). We should check it
strictly by setting .strict_start_type = LWTUNNEL_IP(6)_OPTS.
This patch also adds missing LWTUNNEL_IP6_OPTS in ip6_tun_policy.
Fixes: 4ece47787077 ("lwtunnel: add options setting and dumping for geneve")
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ct_policy and mpls_policy are parsed with nla_parse_nested(), which
does NL_VALIDATE_STRICT validation, strict_start_type is not needed
to set as it is actually trying to make some attributes parsed with
NL_VALIDATE_STRICT.
This patch is to remove it, and do the same on rtm_nh_policy which
is parsed by nlmsg_parse().
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Reviewed-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Xin Long says:
====================
net: sched: support vxlan and erspan options
This patchset is to add vxlan and erspan options support in
cls_flower and act_tunnel_key. The form is pretty much like
geneve_opts in:
https://patchwork.ozlabs.org/patch/935272/
https://patchwork.ozlabs.org/patch/954564/
but only one option is allowed for vxlan and erspan.
v1->v2:
- see each patch changelog.
====================
Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to allow matching options in erspan.
The options can be described in the form:
VER:INDEX:DIR:HWID/VER:INDEX_MASK:DIR_MASK:HWID_MASK.
When ver is set to 1, index will be applied while dir
and hwid will be ignored, and when ver is set to 2,
dir and hwid will be used while index will be ignored.
Different from geneve, only one option can be set. And
also, geneve options, vxlan options or erspan options
can't be set at the same time.
# ip link add name erspan1 type erspan external
# tc qdisc add dev erspan1 ingress
# tc filter add dev erspan1 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
erspan_opts 1:12:0:0/1:ffff:0:0 \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- improve some err msgs of extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to allow matching gbp option in vxlan.
The options can be described in the form GBP/GBP_MASK,
where GBP is represented as a 32bit hexadecimal value.
Different from geneve, only one option can be set. And
also, geneve options and vxlan options can't be set at
the same time.
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev vxlan0 ingress
# tc filter add dev vxlan0 protocol ip parent ffff: \
flower \
enc_src_ip 10.0.99.192 \
enc_dst_ip 10.0.99.193 \
enc_key_id 11 \
vxlan_opts 01020304/ffffffff \
ip_proto udp \
action mirred egress redirect dev eth0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to allow setting erspan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options,
vxlan options or erspan options can't be set at the
same time.
Options are expressed as ver:index:dir:hwid, when ver
is set to 1, index will be applied while dir and hwid
will be ignored, and when ver is set to 2, dir and
hwid will be used while index will be ignored.
# ip link add name erspan1 type erspan external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
erspan_opts 1:2:0:0 \
action mirred egress redirect dev erspan1
v1->v2:
- do the validation when dst is not yet allocated as Jakub suggested.
- use Duplicate instead of Wrong in err msg for extack.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is to allow setting vxlan options using the
act_tunnel_key action. Different from geneve options,
only one option can be set. And also, geneve options
and vxlan options can't be set at the same time.
gbp is the only param for vxlan options:
# ip link add name vxlan0 type vxlan dstport 0 external
# tc qdisc add dev eth0 ingress
# tc filter add dev eth0 protocol ip parent ffff: \
flower indev eth0 \
ip_proto udp \
action tunnel_key \
set src_ip 10.0.99.192 \
dst_ip 10.0.99.193 \
dst_port 6081 \
id 11 \
vxlan_opts 01020304 \
action mirred egress redirect dev vxlan0
v1->v2:
- add .strict_start_type for enc_opts_policy as Jakub noticed.
- use Duplicate instead of Wrong in err msg for extack as Jakub
suggested.
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If rvu_get_blkaddr() fails, then this rvu_cgx_nix_cuml_stats() returns
zero and we write some uninitialized data into the debugfs output.
On the error paths, the use of the uninitialized "*stat" is harmless,
but it will lead to a Smatch warning (static analysis) and a UBSan
warning (runtime analysis) so we should prevent that as well.
Fixes: f967488d095e ("octeontx2-af: Add per CGX port level NIX Rx/Tx counters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If transport->init() fails, we can't assign the transport to the
socket, because it's not initialized correctly, and any future
calls to the transport callbacks would have an unexpected behavior.
Fixes: c0cfa2d8a788 ("vsock: add multi-transports support")
Reported-and-tested-by: syzbot+e2e5c07bf353b2f79daa@syzkaller.appspotmail.com
Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Jorgen Hansen <jhansen@vmware.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current ampdu locking code does not unlock its mutex in the early
return case. This patch fixes it.
Signed-off-by: Markus Theil <markus.theil@tu-ilmenau.de>
Acked-by: Felix Fietkau <nbd@nbd.name>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In nbd_add_socket when krealloc succeeds, if nsock's allocation fail the
reallocted memory is leak. The correct behaviour should be assigning the
reallocted memory to config->socks right after success.
Reviewed-by: Josef Bacik <josef@toxicpanda.com>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
for-5.5/drivers-post
Pull NVMe changes from Keith:
"- The only new feature is the optional hwmon support for nvme (Guenter
and Akinobu)
- A universal work-around for controllers reading discard payloads
beyond the range boundary (Eduard)
- Chaitanya graciously agreed to share the target driver maintenance"
* 'nvme-5.5' of git://git.infradead.org/nvme:
nvme: hwmon: add quirk to avoid changing temperature threshold
nvme: hwmon: provide temperature min and max values for each sensor
nvmet: add another maintainer
nvme: Discard workaround for non-conformant devices
nvme: Add hardware monitoring support
|
|
This adds a new quirk NVME_QUIRK_NO_TEMP_THRESH_CHANGE to avoid changing
the value of the temperature threshold feature for specific devices that
show undesirable behavior.
Guenter reported:
"On my Intel NVME drive (SSDPEKKW512G7), writing any minimum limit on the
Composite temperature sensor results in a temperature warning, and that
warning is sticky until I reset the controller.
It doesn't seem to matter which temperature I write; writing -273000 has
the same result."
The Intel NVMe has the latest firmware version installed, so this isn't
a problem that was ever fixed.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
According to the NVMe specification, the over temperature threshold and
under temperature threshold features shall be implemented for Composite
Temperature if a non-zero WCTEMP field value is reported in the Identify
Controller data structure. The features are also implemented for all
implemented temperature sensors (i.e., all Temperature Sensor fields that
report a non-zero value).
This provides the over temperature threshold and under temperature
threshold for each sensor as temperature min and max values of hwmon
sysfs attributes.
The WCTEMP is already provided as a temperature max value for Composite
Temperature, but this change isn't incompatible. Because the default
value of the over temperature threshold for Composite Temperature is
the WCTEMP.
Now the alarm attribute for Composite Temperature indicates one of the
temperature is outside of a temperature threshold. Because there is only
a single bit in Critical Warning field that indicates a temperature is
outside of a threshold.
Example output from the "sensors" command:
nvme-pci-0100
Adapter: PCI adapter
Composite: +33.9°C (low = -273.1°C, high = +69.8°C)
(crit = +79.8°C)
Sensor 1: +34.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 2: +31.9°C (low = -273.1°C, high = +65261.8°C)
Sensor 5: +47.9°C (low = -273.1°C, high = +65261.8°C)
This also adds helper macros for kelvin from/to milli Celsius conversion,
and replaces the repeated code in hwmon.c.
Cc: Keith Busch <kbusch@kernel.org>
Cc: Jens Axboe <axboe@fb.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Sagi Grimberg <sagi@grimberg.me>
Cc: Jean Delvare <jdelvare@suse.com>
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
Sagi and I have been pretty busy lately, and Chaitanya has been
helping a lot with target work and agreed to share the load.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Keith Busch <kbusch@kernel.org>
|
|
We really don't need this, as the slow path will do the right thing
anyway.
This reverts commit 6952a7f8446ee85ea9d10ab87b64797a031eaae3.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Requests that triggers flushing volatile writeback cache to disk (barriers)
have significant effect to overall performance.
Block layer has sophisticated engine for combining several flush requests
into one. But there is no statistics for actual flushes executed by disk.
Requests which trigger flushes usually are barriers - zero-size writes.
This patch adds two iostat counters into /sys/class/block/$dev/stat and
/proc/diskstats - count of completed flush requests and their total time.
Signed-off-by: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Add kernel AUX area sampling definitions, which brings perf_event.h into
line with the kernel version.
New sample type PERF_SAMPLE_AUX requests a sample of the AUX area
buffer. New perf_event_attr member 'aux_sample_size' specifies the
desired size of the sample.
Also add support for parsing samples containing AUX area data i.e.
PERF_SAMPLE_AUX.
Committer notes:
I squashed the first two patches in this series to avoid breaking
automatic bisection, i.e. after applying only the original first patch
in this series we would have:
# perf test -v parsing
26: Sample parsing :
--- start ---
test child forked, pid 17018
sample format has changed, some new PERF_SAMPLE_ bit was introduced - test needs updating
test child finished with -1
---- end ----
Sample parsing: FAILED!
#
With the two paches combined:
# perf test parsing
26: Sample parsing : Ok
#
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Jiri Olsa <jolsa@redhat.com>
Link: http://lore.kernel.org/lkml/20191115124225.5247-3-adrian.hunter@intel.com
Signed-off-by: Arnaldo Carvalho de Melo <acme@redhat.com>
|
|
Preparatory work for shattering mmu.c into multiple files. Besides making it easier
to follow, this will also make it possible to write unit tests for various parts.
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
apic-access-page
According to Intel SDM section 28.3.3.3/28.3.3.4 Guidelines for Use
of the INVVPID/INVEPT Instruction, the hypervisor needs to execute
INVVPID/INVEPT X in case CPU executes VMEntry with VPID/EPTP X and
either: "Virtualize APIC accesses" VM-execution control was changed
from 0 to 1, OR the value of apic_access_page was changed.
In the nested case, the burden falls on L1, unless L0 enables EPT in
vmcs02 but L1 enables neither EPT nor VPID in vmcs12. For this reason
prepare_vmcs02() and load_vmcs12_host_state() have special code to
request a TLB flush in case L1 does not use EPT but it uses
"virtualize APIC accesses".
This special case however is not necessary. On a nested vmentry the
physical TLB will already be flushed except if all the following apply:
* L0 uses VPID
* L1 uses VPID
* L0 can guarantee TLB entries populated while running L1 are tagged
differently than TLB entries populated while running L2.
If the first condition is false, the processor will flush the TLB
on vmentry to L2. If the second or third condition are false,
prepare_vmcs02() will request KVM_REQ_TLB_FLUSH. However, even
if both are true, no extra TLB flush is needed to handle the APIC
access page:
* if L1 doesn't use VPID, the second condition doesn't hold and the
TLB will be flushed anyway.
* if L1 uses VPID, it has to flush the TLB itself with INVVPID and
section 28.3.3.3 doesn't apply to L0.
* even INVEPT is not needed because, if L0 uses EPT, it uses different
EPTP when running L2 than L1 (because guest_mode is part of mmu-role).
In this case SDM section 28.3.3.4 doesn't apply.
Similarly, examining nested_vmx_vmexit()->load_vmcs12_host_state(),
one could note that L0 won't flush TLB only in cases where SDM sections
28.3.3.3 and 28.3.3.4 don't apply. In particular, if L0 uses different
VPIDs for L1 and L2 (i.e. vmx->vpid != vmx->nested.vpid02), section
28.3.3.3 doesn't apply.
Thus, remove this flush from prepare_vmcs02() and nested_vmx_vmexit().
Side-note: This patch can be viewed as removing parts of commit
fb6c81984313 ("kvm: vmx: Flush TLB when the APIC-access address changes”)
that is not relevant anymore since commit
1313cc2bd8f6 ("kvm: mmu: Add guest_mode to kvm_mmu_page_role”).
i.e. The first commit assumes that if L0 use EPT and L1 doesn’t use EPT,
then L0 will use same EPTP for both L0 and L1. Which indeed required
L0 to execute INVEPT before entering L2 guest. This assumption is
not true anymore since when guest_mode was added to mmu-role.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
arch/x86/kvm/x86.c: In function kvm_make_scan_ioapic_request_mask:
arch/x86/kvm/x86.c:7911:7: warning: variable called set but not
used [-Wunused-but-set-variable]
It is not used since commit 7ee30bc132c6 ("KVM: x86: deliver KVM
IOAPIC scan request to target vCPUs")
Signed-off-by: Mao Wenan <maowenan@huawei.com>
Fixes: 7ee30bc132c6 ("KVM: x86: deliver KVM IOAPIC scan request to target vCPUs")
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
vmcs->apic_access_page is simply a token that the hypervisor puts into
the PFN of a 4KB EPTE (or PTE if using shadow-paging) that triggers
APIC-access VMExit or APIC virtualization logic whenever a CPU running
in VMX non-root mode read/write from/to this PFN.
As every write either triggers an APIC-access VMExit or write is
performed on vmcs->virtual_apic_page, the PFN pointed to by
vmcs->apic_access_page should never actually be touched by CPU.
Therefore, there is no need to mark vmcs02->apic_access_page as dirty
after unpin it on L2->L1 emulated VMExit or when L1 exit VMX operation.
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Reviewed-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Conflicts:
arch/x86/kvm/vmx/vmx.c
|
|
If X86_FEATURE_RTM is disabled, the guest should not be able to access
MSR_IA32_TSX_CTRL. We can therefore use it in KVM to force all
transactions from the guest to abort.
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The current guest mitigation of TAA is both too heavy and not really
sufficient. It is too heavy because it will cause some affected CPUs
(those that have MDS_NO but lack TAA_NO) to fall back to VERW and
get the corresponding slowdown. It is not really sufficient because
it will cause the MDS_NO bit to disappear upon microcode update, so
that VMs started before the microcode update will not be runnable
anymore afterwards, even with tsx=on.
Instead, if tsx=on on the host, we can emulate MSR_IA32_TSX_CTRL for
the guest and let it run without the VERW mitigation. Even though
MSR_IA32_TSX_CTRL is quite heavyweight, and we do not want to write
it on every vmentry, we can use the shared MSR functionality because
the host kernel need not protect itself from TSX-based side-channels.
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Because KVM always emulates CPUID, the CPUID clear bit
(bit 1) of MSR_IA32_TSX_CTRL must be emulated "manually"
by the hypervisor when performing said emulation.
Right now neither kvm-intel.ko nor kvm-amd.ko implement
MSR_IA32_TSX_CTRL but this will change in the next patch.
Reviewed-by: Jim Mattson <jmattson@google.com>
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
"Shared MSRs" are guest MSRs that are written to the host MSRs but
keep their value until the next return to userspace. They support
a mask, so that some bits keep the host value, but this mask is
only used to skip an unnecessary MSR write and the value written
to the MSR is always the guest MSR.
Fix this and, while at it, do not update smsr->values[slot].curr if
for whatever reason the wrmsr fails. This should only happen due to
reserved bits, so the value written to smsr->values[slot].curr
will not match when the user-return notifier and the host value will
always be restored. However, it is untidy and in rare cases this
can actually avoid spurious WRMSRs on return to userspace.
Cc: stable@vger.kernel.org
Reviewed-by: Jim Mattson <jmattson@google.com>
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
KVM does not implement MSR_IA32_TSX_CTRL, so it must not be presented
to the guests. It is also confusing to have !ARCH_CAP_TSX_CTRL_MSR &&
!RTM && ARCH_CAP_TAA_NO: lack of MSR_IA32_TSX_CTRL suggests TSX was not
hidden (it actually was), yet the value says that TSX is not vulnerable
to microarchitectural data sampling. Fix both.
Cc: stable@vger.kernel.org
Tested-by: Jim Mattson <jmattson@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvmarm/kvmarm into HEAD
KVM/arm updates for Linux 5.5:
- Allow non-ISV data aborts to be reported to userspace
- Allow injection of data aborts from userspace
- Expose stolen time to guests
- GICv4 performance improvements
- vgic ITS emulation fixes
- Simplify FWB handling
- Enable halt pool counters
- Make the emulated timer PREEMPT_RT compliant
Conflicts:
include/uapi/linux/kvm.h
|
|
fbdev uses the physical address of our framebuffer for its fb_mmap()
routine. While we need to adapt this address for the new io BAR, we have
to fix v5.4 first! The simplest fix is to restore the smem back to v5.3
and we will then probably have to implement our fbops->fb_mmap() callback
to handle local memory.
Reported-by: Neil MacLeod <freedesktop@nmacleod.com>
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=112256
Fixes: 5f889b9a61dd ("drm/i915: Disregard drm_mode_config.fb_base")
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Tested-by: Neil MacLeod <freedesktop@nmacleod.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113180633.3947-1-chris@chris-wilson.co.uk
(cherry picked from commit abc5520704ab438099fe352636b30b05c1253bea)
Signed-off-by: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
(cherry picked from commit 9faf5fa4d3dad3b0c0fa6e67689c144981a11c27)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
