| Age | Commit message (Collapse) | Author |
|---|
|
Instead of individual values use an array to store the registers need to be
saved on suspend and restored on resume.
It is going to be easier to add more registers to save and restore.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The selftest code removes its testcase data from the live tree when
exiting, but if the testcases data tree contains an empty child of the
root, then it causes an oops due to a NULL dereference. The reason is
that the code tries to directly dereference the child pointer without
checking first if a child is actually there.
The solution is to pass the parent node into detach_node_and_children()
instead of trying to pass the child. This required removing the code
that attempts to remove all of the sibling nodes in
detach_node_and_children(), which was never sensible in the first place.
At the same time add a check to make sure the bounds of the nodes list
are not exceeded by the testdata tree. If they are then abort.
Signed-off-by: Grant Likely <grant.likely@linaro.org>
Cc: Gaurav Minocha <gaurav.minocha.os@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom into next/defconfig
Pull "Qualcomm ARM Based defconfig Updates for v3.18" from Kumar Gala:
* General defconfig update to match upstream changes
* Enable IPQ806x & APQ8084 clk support
* Enable pinctrl on MSM8960 & APQ8084
* Enable CPU_IDLE to get basic wfi support
* Enable SPI NOR and MTD M25P80 support (used on AP148 board)
* Enable SATA PHY support on IPQ806x and APQ8064
* Enable Fixed regulator and ARM MMCI support (mmc support on APQ8064)
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
* tag 'qcom-defconfig-for-3.18' of git://git.kernel.org/pub/scm/linux/kernel/git/galak/linux-qcom:
ARM: qcom: Update defconfig
ARM: qcom: Update defconfig
|
|
The rq_complete tracepoint was never issued for empty requests,
causing the resulting blktrace information to never show any
completion for those request.
Signed-off-by: Hannes Reinecke <hare@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
This patch removes the use of the IRQF_DISABLED flag
from drivers/block/hd.c
It's a NOOP since 2.6.35 and it will be removed one day.
This also removes a related comment which is obsolete too.
Signed-off-by: Michael Opdenacker <michael.opdenacker@free-electrons.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
The K2L MDIO io space has different start address.
Hence, fix it to be 0x26200f00 according to TRM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The K2E MDIO io space has different start address.
Hence, fix it to be 0x24200f00 according to TRM.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
Keystone supports dma-coherent on USB master and also needs
dma-ranges to specify the hardware alias memory range in which DMA
can be operational.
Such configuration applied for USB0 devices, but It's missed for
USB1 device which is present only in K2E SoC - hence apply it.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
The IO range size is set incorrectly for USB PHY0 deivice
it should be 24 instead of 32. Otherwise, It causes
USB PHY1 probing failure.
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
|
|
This patch fixes a regression in the patch "GFS2: Remember directory
insert point", commit 2b47dad866d04f14c328f888ba5406057b8c7d33.
The problem had to do with the rename function: The function found
space for the new dirent, and remembered that location. But then the
old dirent was removed, which often moved the eligible location for
the renamed dirent. Putting the new dirent at the saved location
caused file system corruption.
This patch adds a new "save_loc" variable to struct gfs2_diradd.
If 1, the dirent location is saved. If 0, the dirent location is not
saved and the buffer_head is released as per previous behavior.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Steven Whitehouse <swhiteho@redhat.com>
|
|
Helpful for debugging as the version shows up in a
register dump.
Cc: Jay Cornwall <jay.cornwall@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
We should never have a packet 0 in the command stream.
Dump the full command stream to help debug.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=84500
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The requirement for these was removed in:
0a168933976eb483da91161316bbbbcb74d00486
Reviewed-by: Christian König <christian.koenig@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
legacy_connector_convert is used in radeon_combios.c only, so declare it as static.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The tables:
* supported_devices_connector_convert
* supported_devices_connector_object_id_convert
* object_connector_convert
are used in redeon_atombios.c only, so declare them as static.
Signed-off-by: Michele Curti <michele.curti@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
It's no longer used now that the underlying bugs are fixed.
Reviewed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No longer needed now that the underlying bug was fixed in
e07929810f0a19ddd756558290c7d72827cbfcd9
(drm/radeon/dpm: fix typo in vddci setup for eg/btc).
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69721
Reviewed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not sure this was ever necessary for CI, was just done
to be on the safe side.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69721
Reviewed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Not sure this was ever necessary for SI, was just done
to be on the safe side.
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69721
Reviewed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
No longer needed now that the underlying bug was fixed in
b0880e87c1fd038b84498944f52e52c3e86ebe59
(drm/radeon/dpm: fix vddci setup typo on cayman).
bug:
https://bugs.freedesktop.org/show_bug.cgi?id=69721
Reviewed-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Tested-by: Alexandre Demers <alexandre.f.demers@gmail.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This should allow the audio driver to get a better
idea of whether the sink is connected or not.
v2: fix copy/paste typo noticed by David Henningsson
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Clean up the enable sequence as well.
V2: clean up duplicate defines
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Most of that functionality is only used by r600_hdmi.c
and I'm planning to change that further.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
Only need one copy.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
no functional change.
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
This patch introduces the halt_wakeup counter used by common code and uses it to
count vcpu wakeups done in s390 arch specific code.
Acked-by: Cornelia Huck <cornelia.huck@de.ibm.com>
Signed-off-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
|
|
There is nothing to do for KVM to support TOD-CLOCK steering.
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Reviewed-by: David Hildenbrand <dahi@linux.vnet.ibm.com>
|
|
There is a second mouse sharing the same vendor strings but different IDs.
Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
As Michael suggested, the hex prefix for the output of EEH PE
state sysfs entry (/sys/bus/pci/devices/xxx/eeh_pe_state) is
always informative to users.
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
S3C2412, S3C2443 and their derivatives contain a special software-reset
register in their system-controller.
Therefore register a restart handler for those.
Tested on a s3c2416-based board, s3c2412 compile-tested.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add infrastructure to write the correct value to the restart register and
register the restart notifier for both rk3188 (including rk3066) and rk3288.
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Add a Kconfig option to enable the blk-mq path for SCSI by default
to ease testing and deployment in setups that know they benefit
from blk-mq.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Reviewed-by: Robert Elliott <elliott@hp.com>
Tested-by: Robert Elliott <elliott@hp.com>
|
|
- Adding some of the definitions missing in unipro.h, including power
enumeration.
- Read Modify Write Line helper function
- Indication for the type of suspend
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add capability to control the auto bkops during suspend.
If host explicitly enables the auto bkops (background operation) on device
then only device would perform the bkops on its own. If auto bkops is not
enabled explicitly and if the device reaches to state where it must do
background operation, device would raise the urgent bkops exception event
to host and then host will enable the auto bkops on device. This patch
adds the option to choose whether auto bkops should be enabled during
runtime suspend or not. Since we don't want to keep the device active to
perform the non critical bkops, host will enable urgent bkops only.
Keep auto-bkops enabled after resume if urgent bkops needed.
If device bkops status shows that its in critical need of executing
background operations, host should allow the device to continue doing
background operations.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The clocks for UFS device will be managed by generic DVFS (Dynamic
Voltage and Frequency Scaling) framework within kernel. This devfreq
framework works with different governors to scale the clocks. By default,
UFS devices uses simple_ondemand governor which scales the clocks up if
the load is more than upthreshold and scales down if the load is less than
downthreshold.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add freq-table-hz propery for UFS device to keep track of
<min max> frequencies supported by UFS clocks.
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The UFS controller clocks can be gated after certain period of
inactivity, which is typically less than runtime suspend timeout.
In addition to clocks the link will also be put into Hibern8 mode
to save more power.
The clock gating can be turned on by enabling the capability
UFSHCD_CAP_CLK_GATING. To enable entering into Hibern8 mode as part of
clock gating, set the capability UFSHCD_CAP_HIBERN8_WITH_CLK_GATING.
The tracing events for clock gating can be enabled through debugfs as:
echo 1 > /sys/kernel/debug/tracing/events/ufs/ufshcd_clk_gating/enable
cat /sys/kernel/debug/tracing/trace_pipe
Signed-off-by: Sahitya Tummala <stummala@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Sometimes, the device shall report its maximum power and speed
capabilities, but we might not wish to configure it to use those
maximum capabilities.
This change adds support for the vendor specific host driver to
implement power change notify callback.
To enable configuring different power modes (number of lanes,
gear number and fast/slow modes) it is necessary to split the
configuration stage from the stage that reads the device max power mode.
In addition, it is not required to read the configuration more than
once, thus the configuration is stored after reading it once.
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
This patch adds support for UFS device and UniPro link power management
during runtime/system PM.
Main idea is to define multiple UFS low power levels based on UFS device
and UFS link power states. This would allow any specific platform or pci
driver to choose the best suited low power level during runtime and
system suspend based on their power goals.
bkops handlig:
To put the UFS device in sleep state when bkops is disabled, first query
the bkops status from the device and enable bkops on device only if
device needs time to perform the bkops.
START_STOP handling:
Before sending START_STOP_UNIT to the device well-known logical unit
(w-lun) to make sure that the device w-lun unit attention condition is
cleared.
Write protection:
UFS device specification allows LUs to be write protected, either
permanently or power on write protected. If any LU is power on write
protected and if the card is power cycled (by powering off VCCQ and/or
VCC rails), LU's write protect status would be lost. So this means those
LUs can be written now. To ensures that UFS device is power cycled only
if the power on protect is not set for any of the LUs, check if power on
write protect is set and if device is in sleep/power-off state & link in
inactive state (Hibern8 or OFF state).
If none of the Logical Units on UFS device is power on write protected
then all UFS device power rails (VCC, VCCQ & VCCQ2) can be turned off if
UFS device is in power-off state and UFS link is in OFF state. But current
implementation would disable all device power rails even if UFS link is
not in OFF state.
Low power mode:
If UFS link is in OFF state then UFS host controller can be power collapsed
to avoid leakage current from it. Note that if UFS host controller is power
collapsed, full UFS reinitialization will be required on resume to
re-establish the link between host and device.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS device may have standard LUs and LUN id could be from 0x00 to 0x7F.
UFS device specification use "Peripheral Device Addressing Format"
(SCSI SAM-5) for standard LUs.
UFS device may also have the Well Known LUs (also referred as W-LU) which
again could be from 0x00 to 0x7F. For W-LUs, UFS device specification only
allows the "Extended Addressing Format" (SCSI SAM-5) which means the W-LUNs
would start from 0xC100 onwards.
This means max. LUN number reported from UFS device could be 0xC17F hence
this patch advertise the "max_lun" as 0xC17F which will allow SCSI mid
layer to detect the W-LUs as well.
But once the W-LUs are detected, UFSHCD driver may get the commands with
SCSI LUN id upto 0xC17F but UPIU LUN id field is only 8-bit wide so it
requires the mapping of SCSI LUN id to UPIU LUN id. This patch also add
support for this mapping.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS device specification requires the UFS devices to support 4 well known
logical units:
"REPORT_LUNS" (address: 01h)
"UFS Device" (address: 50h)
"RPMB" (address: 44h)
"BOOT" (address: 30h)
UFS device's power management needs to be controlled by "POWER CONDITION"
field of SSU (START STOP UNIT) command. But this "power condition" field
will take effect only when its sent to "UFS device" well known logical unit
hence we require the scsi_device instance to represent this logical unit in
order for the UFS host driver to send the SSU command for power management.
We also require the scsi_device instance for "RPMB" (Replay Protected
Memory Block) LU so user space process can control this LU. User space may
also want to have access to BOOT LU.
This patch adds the scsi device instances for each of all well known LUs
(except "REPORT LUNS" LU).
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
The maximum power consumption in active is determined by bActiveICCLevel.
The configuration is done by reading max current supported by the
regulators connected to VCC, VCCQ and VCCQ2 rails on the boards, and
reading the current consumption levels from the device for each rails
(vcc/vccq/vccq2) using power descriptor.
We configure the bActiveICCLevel attribute, with the max value that
correspond to the minimum-of(VCC-current-level,VCCQ-current-level,
VCCQ2-current-level).
In order to minimize resume latency, pre-fetch icc levels and reference
clock during initialization and avoid reading them each link startup
during resume.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Yaniv Gardi <ygardi@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
In ->hce_enable_notify() callback the vendor specific initialization
may carry out additional DME configuration using UIC commands and
hence the UIC command completion interrupt enable bit should be set
before the post reset notification.
Add retries if the link-startup fails. This is required since due to
hardware timing issues, the Uni-Pro link-startup might fail. The UFS
HCI recovery procedure contradicts the Uni-Pro sequence. The UFS HCI
specifies to resend DME_LINKSTARTUP command after IS.ULLS (link-lost
interrupt) is received. The Uni-Pro specifies that if link-startup
fails the link is in "down" state. The link-lost is indicated to the
DME user only when the link is up. Hence, the UFS HCI recovery procedure
of waiting for IS.ULLS and retrying link-startup may not work properly.
At the end, if detection fails, power off (disable clocks, regulators,
phy) if the UFS device detection fails. This saves power while UFS device
is not embedded into the system.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Currently reading query descriptor is more tightened to each
descriptor type. This patch generalize the approach and allows
reading any parameter from any query descriptor.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add the support for voting of the regulator powering the
host controller logic.
Signed-off-by: Raviv Shvili <rshvili@codeaurora.org>
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Add generic clock initialization support for UFSHCD platform
driver. The clock info is read from device tree using standard
clock bindings. A generic max-clock-frequency-hz property is
defined to save information on maximum operating clock frequency
the h/w supports.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
UFS devices are powered by at most three external power supplies -
- VCC - The flash memory core power supply, 2.7V to 3.6V or 1.70V to 1.95V
- VCCQ - The controller and I/O power supply, 1.1V to 1.3V
- VCCQ2 - Secondary controller and/or I/O power supply, 1.65V to 1.95V
For some devices VCCQ or VCCQ2 are optional as they can be
generated using internal LDO inside the UFS device.
Add DT bindings for voltage regulators that can be controlled
from host driver.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some vendor specific controller versions might need to configure
vendor specific - registers, clocks, voltage regulators etc. to
initialize the host controller UTP layer and Uni-Pro stack.
Provide some common initialization operations that can be used
to configure vendor specifics. The methods can be extended in
future, for example, for power mode transitions.
The operations are vendor/board specific and hence determined with
the help of compatible property in device tree.
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
If LLD has added scsi device (by calling scsi_add_device) before scheduling
async scsi_scan_host then scsi_finish_async_scan() will end up calling
scsi_sysfs_add_sdev for scsi device which was already added by LLD.
This patch fixes this issue by skipping the call to scsi_sysfs_add_sdev()
if it's already visible to rest of the kernel.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: Martin K. Petersen <martin.petersen@oracle.com>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Some devices may respond with wrong type for well-known logical units.
This patch forces well-known type for devices which doesn't report it
correct.
Signed-off-by: Subhash Jadavani <subhashj@codeaurora.org>
Signed-off-by: Sujit Reddy Thumma <sthumma@codeaurora.org>
Signed-off-by: Dolev Raviv <draviv@codeaurora.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
