| Age | Commit message (Collapse) | Author |
|---|
|
As there is a mx53_smd board in the kernel, using SMD_FEC_PHY_RST as the pin name can be misleading when used
on a MX53_EVK board.
Change the pin name to reflect the board name.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Current code inside mx53_evk_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Current code inside babbage_fec_reset uses gpio_direction_output with initial value of the GPIO and also sets
the GPIO value via gpio_set_value to the same level right after. This is not needed.
By using gpio_request_one it is possible to set the direction and initial value in one shot.
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Signed-off-by: Frank Li <Frank.Li@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Having the silicon revision to appear on the boot log is a useful information.
MX31 and MX35 already show the silicon revision on boot.
Add support for displaying such information for MX51 as well.
Tested on a MX51EVK, where it shows:
CPU identified as i.MX51, silicon rev 3.0
Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
|
|
Cameras are currently broken on ARM sh-mobile platforms. They need a
suitable coherent DMA mask.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Use GPIO_PORT31 to control the backlight on the Mackerel board.
Signed-off-by: Magnus Damm <damm@opensource.se>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Since commit 34d0b5af50a063cded842716633501b38ff815fb it is no longer
possible to debug an application using singlestep. The old commit
converted singlestep handling via ptrace to hw_breakpoints. The
hw_breakpoint is disabled when an event is triggered and not re-enabled
again. This patch re-enables the existing hw_breakpoint before the
existing breakpoint is reused.
Signed-off-by: David Engraf <david.engraf@sysgo.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Commit 0ea820cf introduced the PTRACE_GETFPREGS/SETFPREGS cmds,
but gdb-server still accesses the FPU state using the
PTRACE_PEEKUSR/POKEUSR commands. In this case, xstate was not
initialised.
Signed-off-by: Phil Edworthy <phil.edworthy@renesas.com>
Cc: stable@kernel.org
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Correct ->dequeue_tree() thinko into sched_class->dequeue_task
and drop all references to ->task_new() since it is obviously
gone.
Signed-off-by: Borislav Petkov <borislav.petkov@amd.com>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Mike Galbraith <efault@gmx.de>
LKML-Reference: <1300815978-16618-1-git-send-email-bp@amd64.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20110323123828.GB4244@swordfish.minsk.epam.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
alloc_fair_sched_group()
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <20110323111722.GA4244@swordfish.minsk.epam.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
The sentence uses the possessive pronoun, which is spelled
without an apostrophe.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
Cc: Jiri Kosina <trivial@kernel.org>
Cc: Peter Zijlstra <peterz@infradead.org>
LKML-Reference: <1300735487-2406-1-git-send-email-j.neuschaefer@gmx.net>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
|
|
Now that the in-tree offenders have seemingly all caught up, we can
finally unconditionally select this.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
This converts the PMB code over to use the new syscore_ops and kills off
the old sysdev utilization, as per Rafael's example.
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
Convert the SuperH clocks framework and shared interrupt handling
code to using struct syscore_ops instead of a sysdev classes and
sysdevs for power managment.
This reduces the code size significantly and simplifies it. The
optimizations causing things not to be restored after creating a
hibernation image are removed, but they might lead to undesirable
effects during resume from hibernation (e.g. the clocks would be left
as the boot kernel set them, which might be not the same way as the
hibernated kernel had seen them before the hibernation).
This also is necessary for removing sysdevs from the kernel entirely
in the future.
Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
Signed-off-by: Paul Mundt <lethal@linux-sh.org>
|
|
For consistency with the write path push byte swaps of the WM8994 register
data out of the bulk read data path into the per-register APIs. The only
user of the bulk register read is the interrupt code which is updated to
do the swaps itself part of this patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Rename AB8500 GPADC header so as not to be redunantly named.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Allow const buffers to be passed in without type safety issues.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
For bulk I/O it is both convenient and more sensible to pre-swap the data
rather than doing the swap as part of the I/O operation so move the byte
swaps we're currently doing into the core write function into the register
based functions, giving the bulk write function a straight pass through
to the chip.
This leaves reads inconsistent, this will be addressed as a followup patch.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As well as providing a trivial performance optimisation this also avoids
allocating a copy of the message on the stack which is beneficial when
doing large transfers.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This saves us allocating an array on the stack, giving a meaningless
performance improvement and ensuring that if drivers ever do large writes
we'll not allocate large arrays on the stack.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
They're not exported.
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This adds a subdriver for the regulator found inside the TPS61050
and TPS61052 chips.
Cc: Samuel Ortiz <samuel.ortiz@intel.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The TPS61050/TPS61052 are boost converters, LED drivers, LED flash
drivers and a simple GPIO pin chips.
Cc: Liam Girdwood <lrg@slimlogic.co.uk>
Cc: Mark Brown <broonie@opensource.wolfsonmicro.com>
Cc: Jonas Aberg <jonas.aberg@stericsson.com>
Cc: Ola Lilja <ola.o.lilja@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Almost the same driver for both Poulsbo and Tunnel Creek.
The difference is in quantity of GPIOs powered by the core power
rail and by suspend power supply, default values for some GPIOs, etc.
Detect actual hardware by platform device ID assigned in lpc_sch
and set configuration accordingly.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Grant Likely <grant.likely@secretlab.ca>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Intel Poulsbo SCH and Tunnel Creek provide almost the
same LPC interface. Use the same driver for both devices while
storing PCI ID to distinguish between platforms to apply plarform
related quirks.
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Denis Turischev <denis@compulab.co.il>
Acked-by: Jesse Barnes <jbarnes@virtuousgeek.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch supports PMIC/Regulator part of MAX8997/MAX8966 MFD.
In this initial release, selecting voltages or current-limit
and switching on/off the regulators are supported.
Controlling voltages for DVS with GPIOs is not implemented fully
and requires more considerations: it controls multiple bucks (selection
of 1, 2, and 5) at the same time with SET1~3 gpios. Thus, when DVS-GPIO
is activated, we lose the ability to control the voltage of a single
buck regulator independently; i.e., contolling a buck affects other two
bucks. Therefore, using the conventional regulator framework directly
might be problematic. However, in this driver, we try to choose
a setting without such side effect of affecting other regulators and
then try to choose a setting with the minimum side effect (the sum of
voltage changes in other regulators).
On the other hand, controlling all the three bucks simultenously based
on the voltage set table may help build cpufreq and similar system
more robust; i.e., all the three voltages are consistent every time
without glitches during transition.
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Append the additional read/write operation on 88pm860x for accessing
test page in 88PM860x.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
onkey/touch/codec/power driver. So move the identification of
device node from those drivers to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
regulator driver. So move the identification of device node from
regulator driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Acked-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
led driver. So move the identification of device node from led
driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Copy 88pm860x platform data into different mfd_data structure for
backlight driver. So move the identification of device node from
backlight driver to mfd driver.
Signed-off-by: Haojian Zhuang <haojian.zhuang@marvell.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since 43cc71eed1250755986da4c0f9898f9a635cb3bf (platform: prefix MODALIAS
with "platform:"), the platform modalias is prefixed with "platform:".
Signed-off-by: Axel Lin <axel.lin@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The GPADC in the AB8500 was incorrectly configured when a charger
current channel was selected.
Signed-off-by: Karl Komierowski <karl.komierowski@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The GPADC found in the AB8500 needs to be calibrated to work
properly. This is done by writing a number of special OTP
(one-time-programmable) registers at production. This patch
makes sure that these values are used to calibrate the returned
value from the GPADC so that it is correct.
Signed-off-by: Johan Palsson <johan.palsson@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This revamps the interface so that AB8500 GPADCs are fetched by
name. Probed GPADCs are added to a list and this list is searched
for a matching GPADC. This makes it possible to have multiple
AB8500 GPADC instances instead of it being a singleton, and
rids the need to keep a GPADC pointer around in the core AB8500
MFD struct.
Currently the match is made to the device name which is by default
numbered from the device instance such as "ab8500-gpadc.0" but
by using the .init_name field of the device a more intiutive
naming for the GPADC blocks can be achieved if desired.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This moves the ab8500-gpadc.h header down into the ab8500/
subdir in include/linux/mfd and fixes some whitespace in the
header in the process.
Signed-off-by: Daniel Willerud <daniel.willerud@stericsson.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
MAX8997/MAX8966 chip is a multi-function device with I2C bussses. The
chip includes PMIC, RTC, Fuel Gauge, MUIC, Haptic, Flash control, and
Battery (charging) control.
This patch is an initial release of a MAX8997/8966 driver that supports
to enable the chip with its primary I2C bus that connects every device
mentioned above except for Fuel Gauge, which uses another I2C bus. The
fuel gauge is not supported by this mfd driver and is supported by a
seperated driver of MAX17042 Fuel Gauge (yes, the fuel gauge part is
compatible with MAX17042).
Signed-off-by: MyungJoo Ham <myungjoo.ham@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@opensource.wolfsonmicro.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
As requested by Samuel, there's not really any reason to have "shared"
in the name.
This also modifies the only user of the function, as well.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
mfd_get_cell returns a const, so change the ds1wm client to store
a const mfd cell. This silences type mismatch warnings.
Since we're guaranteed to have the mfd_cell, we can also simplify
the code a bit to get rid of a temporary variable and NULL check.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds a sysfs file with the ab8500 switch off status.
The switch off status contains information of what caused the ab8500
chip to power off. A print during boot is also added.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This patch adds support for ab8500 chip revision cut 3.0.
Also rephrased from Changes to Author in the header.
Signed-off-by: Mattias Wallin <mattias.wallin@stericsson.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
mfd_get_cell returns a const, so change the jz4740 clients to store
a const mfd cell. This silences type mismatch warnings.
Signed-off-by: Andres Salomon <dilinger@queued.net>
Acked-by: Anton Vorontsov <cbouatmailru@gmail.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
