| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
2 bytes in MSB of register for clock status is zero during intermediate
state after changing status of sampling clock in models of TASCAM FireWire
series. The duration of this state differs depending on cases. During the
state, it's better to retry reading the register for current status of
the clock.
In current implementation, the intermediate state is checked only when
getting current sampling transmission frequency, then retry reading.
This care is required for the other operations to read the register.
This commit moves the codes of check and retry into helper function
commonly used for operations to read the register.
Fixes: e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-3-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
The return value of snd_tscm_stream_get_clock() is ignored. This commit
checks the value and handle error.
Fixes: e453df44f0d6 ("ALSA: firewire-tascam: add PCM functionality")
Cc: <stable@vger.kernel.org> # v4.4+
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190910135152.29800-2-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/broonie/sound into for-next
ASoC: Updates for v5.4
Quite a big update this time around, particularly in the core
where we've had a lot of cleanups from Morimoto-san - there's
not much functional change but quite a bit of modernization
going on. We've also seen a lot of driver work, a lot of it
cleanups but also some particular drivers.
- Lots and lots of cleanups from Morimoto-san and Yue Haibing.
- Lots of cleanups and enhancements to the Freescale, sunxi dnd
Intel rivers.
- Initial Sound Open Firmware suppot for i.MX8.
- Removal of w90x900 and nuc900 drivers as the platforms are
being removed.
- New support for Cirrus Logic CS47L15 and CS47L92, Freescale
i.MX 7ULP and 8MQ, Meson G12A and NXP UDA1334
|
|
|
|
|
|
Add an op in hdmi_codec_ops so codec driver can register callback
function to handle plug event.
Driver in DRM can use this callback function to report connector status.
Signed-off-by: Cheng-Yi Chiang <cychiang@chromium.org>
Link: https://lore.kernel.org/r/20190717083327.47646-2-cychiang@chromium.org
Reviewed-by: Tzung-Bi Shih <tzungbi@google.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of clearing RT5677_PWR_ANLG2 (MX-64h) to 0 at SND_SOC_BIAS_OFF,
we only clear the RT5677_PWR_CORE bit which is set at SND_SOC_BIAS_PREPARE.
MICBIAS control bits are left unchanged.
This fixed the bug where if MICBIAS1 widget is forced on, MICBIAS
control bits will be cleared at suspend and never turned back on again,
since DAPM thinks the widget is always on.
Signed-off-by: Ben Zhang <benzh@chromium.org>
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20190906194636.217881-3-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In order to simplify understanding what register values are being
written to the codec for debugging more advanced features (such as
hotwording) it is best to remove magic numbers
Signed-off-by: Curtis Malainey <cujomalainey@chromium.org>
Link: https://lore.kernel.org/r/20190906194636.217881-2-cujomalainey@chromium.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_unbind_aux_dev() implementation is very half,
thus it is very unreadable.
for_each_comp_order(order) {
for_each_card_auxs_safe(card, comp, _comp) {
(1) if (comp->driver->remove_order == order) {
...
=> soc_unbind_aux_dev(comp);
}
}
soc_unbind_aux_dev() itself is not related to remove_order (1).
And, it is called from soc_remove_aux_devices(), even though
its paired function soc_bind_aux_dev() is called from
snd_soc_instantiate_card().
It is very unbalance, and very difficult to understand.
This patch do
1) update soc_bind_aux_dev() to self contained
2) call it from soc_cleanup_card_resources() to make up balance
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87r24wor0z.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
soc-core.c has soc_bind_aux_dev(), but, there is no its paired
soc_unbind_aux_dev().
This patch adds soc_unbind_aux_dev().
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87sgpcor14.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_bind_aux_dev() implementation is very half,
thus it is very unreadable.
for_each_card_pre_auxs(xxx) {
=> ret = soc_bind_aux_dev(xxx);
...
}
This patch does all for_each_xxx() under soc_bind_aux_dev(),
and makes it to self contained.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87tv9sor1b.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
This patch moves soc_probe_link_dais() next to soc_remove_link_dais()
which is paired function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87v9u8or1g.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_probe_link_dais() implementation is very half,
thus it is very difficult to read.
for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_probe_link_dais(xxx);
}
This patch does all for_each_xxx() under soc_probe_link_dais(),
and makes it to self contained.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87woeoor1m.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_probe_link_dais() (1) is called under probe_order (2),
and it will initialize dai_link related settings at *Last* turn (3)(B).
It is very complex code.
static int soc_probe_link_dais(..., order)
{
(A) /* probe DAIs here */
...
(3) if (order != SND_SOC_COMP_ORDER_LAST)
return 0;
(B) /* initialize dai_link related settings */
...
}
static int snd_soc_instantiate_card(...)
{
...
(2) for_each_comp_order(order) {
for_each_card_rtds(...) {
(1) ret = soc_probe_link_dais(..., order);
}
}
}
This patch separes soc_probe_link_dais() into "DAI probe" portion (A),
and dai_link settings portion (B).
The later is named as soc_link_init() by this patch.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87y2z4or1r.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is easy to read code if it is cleanly using paired function/naming,
like start <-> stop, register <-> unregister, etc, etc.
But, current ALSA SoC code is very random, unbalance, not paired, etc.
It is easy to create bug at the such code, and it will be difficult to
debug.
This patch moves soc_probe_dai() next to soc_remove_dai() which is
paired function.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/87zhjkor1x.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_remove_link_dais() implementation is very half,
thus it is very difficult to read.
for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_remove_link_dais(xxx);
}
This patch does all for_each_xxx() under soc_remove_link_dais(),
and makes it to self contained.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/871rwwq5mm.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_remove_link_components() implementation is very half,
thus it is very difficult to read.
for_each_comp_order(xxx) {
for_each_card_rtds(xxx)
=> soc_remove_link_components(xxx);
}
This patch does all for_each_xxx() under soc_remove_link_components(),
and makes it to self contained.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/8736hcq5ms.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Current soc_probe_link_components() implementation is very half,
thus it is very difficult to read.
for_each_comp_order(xxx) {
for_each_card_rtds(xxx) {
=> ret = soc_probe_link_components(xxx);
...
}
}
This patch does all for_each_xxx() under soc_probe_link_components(),
and makes it to self contained.
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Link: https://lore.kernel.org/r/874l1sq5mx.wl-kuninori.morimoto.gx@renesas.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 82 bytes.
Before:
text data bss dec hex filename
26548 7288 64 33900 846c sound/soc/codecs/rt1308.o
After:
text data bss dec hex filename
26370 7384 64 33818 841a sound/soc/codecs/rt1308.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907074634.22144-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 93 bytes.
Before:
text data bss dec hex filename
38961 9784 64 48809 bea9 sound/soc/codecs/rt1305.o
After:
text data bss dec hex filename
38804 9848 64 48716 be4c sound/soc/codecs/rt1305.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907074156.21907-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the array pd on the stack but instead make it
static const. Makes the object code smaller by 100 bytes.
Before:
text data bss dec hex filename
51463 13016 128 64607 fc5f sound/soc/codecs/rt1011.o
After:
text data bss dec hex filename
51299 13080 128 64507 fbfb sound/soc/codecs/rt1011.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190907073717.21632-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch set 0Hz to sysclk when shutdown the card.
Some codecs set rate constraints that derives from sysclk. This
mechanism works correctly if machine drivers give fixed frequency.
But simple-audio and audio-graph card set variable clock rate if
'mclk-fs' property exists. In this case, rate constraints will go
bad scenario. For example a codec accepts three limited rates
(mclk / 256, mclk / 384, mclk / 512).
Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- Codec set constraints of PCM rate by sysclk
48kHz (1/256), 32kHz (1/384), 24kHz (1/512)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed
- Play 32kHz sound, it's acceptable
- Set sysclk to 8.192MHz (= fs * mclk-fs = 32k * 256)
- Codec set constraints of PCM rate by sysclk
32kHz (1/256), 21.33kHz (1/384), 16kHz (1/512)
- Play 48kHz again, but it's NOT acceptable because constraints
do not allow 48kHz
So codecs treat 0Hz sysclk as signal of applying no constraints to
avoid this problem.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174501.19833-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch ignores sysclk setting if it is 0Hz.
Some codecs treat 0Hz sysclk as signal of applying no constraints.
This driver does not have such feature but current implementation
outputs 'Failed to set mclk' error message if machine driver sets
0Hz sysclk to this driver.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907174332.19586-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Don't populate the arrays on the stack but instead make them
static const. Makes the object code smaller by 37 bytes.
Before:
text data bss dec hex filename
16253 7200 0 23453 5b9d sound/soc/codecs/ad193x.o
After:
text data bss dec hex filename
16056 7360 0 23416 5b78 sound/soc/codecs/ad193x.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20190906161404.1440-1-colin.king@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch supports some type of machine drivers that set 0 to mclk
when sound device goes to idle state. After applied this patch,
sysclk == 0 means there is no constraint of sound rate and other
values will set constraints which is derived by sysclk setting.
Original code refuses sysclk == 0 setting. But some boards and SoC
(such as RockPro64 and RockChip I2S) has connected SoC MCLK out to
ES8316 MCLK in. In this case, SoC side I2S will choose suitable
frequency of MCLK such as fs * mclk-fs when user starts playing or
capturing.
Bad scenario as follows (mclk-fs = 256):
- Initialize sysclk by correct value (Ex. 12.288MHz)
- ES8316 set constraints of PCM rate by sysclk
48kHz (1/256), 32kHz (1/384), 30.720kHz (1/400),
24kHz (1/512), 16kHz (1/768), 12kHz (1/1024)
- Play 48kHz sound, it's acceptable
- Sysclk is not changed
- Play 32kHz sound, it's acceptable
- Set sysclk by 8.192MHz (= fs * mclk-fs = 32k * 256)
- ES8316 set constraints of PCM rate by sysclk
32kHz (1/256), 21.33kHz (1/384), 20.48kHz (1/400),
16kHz (1/512), 10.66kHz (1/768), 8kHz (1/1024)
- Play 48kHz again, but it's NOT acceptable because constraints
list does not allow 48kHz
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907163653.9382-2-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
This patch removes redundant null checks for optional MCLK clock.
And fix DT binding document for changing clock property to optional
from required.
Signed-off-by: Katsuhiro Suzuki <katsuhiro@katsuster.net>
Link: https://lore.kernel.org/r/20190907163653.9382-1-katsuhiro@katsuster.net
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Since commit 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused
GPIOs"), on-board audio has appeared muted. It has been discovered that
believed to be unused GPIO pins "hookflash1" and "hookflash2" need to be
set low for audible sound in handsfree and handset mode respectively.
According to Amstrad E3 wiki, the purpose of both pins hasn't been
clearly identified. Original Amstrad software used to produce a high
pulse on them when the phone was taken off hook or recall was pressed.
With the current findings, we can assume the pins provide a kind of
audio mute function, separately for handset and handsfree operation
modes.
Commit 2afdb4c41d78 ("ARM: OMAP1: ams-delta: Fix audio permanently
muted") attempted to fix the issue temporarily by hogging the GPIO pin
"hookflash1" renamed to "audio_mute", however the fix occurred
incomplete as it restored audible sound only for handsfree mode.
Stop hogging that pin, rename the pins to "handsfree_mute" and
"handset_mute" respectively and implement appropriate DAPM event
callbacks for "Speaker" and "Earpiece" DAPM widgets.
Fixes: 1137ceee76ba ("ARM: OMAP1: ams-delta: Don't request unused GPIOs")
Signed-off-by: Janusz Krzysztofik <jmkrzyszt@gmail.com>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Link: https://lore.kernel.org/r/20190907111650.15440-1-jmkrzyszt@gmail.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Some tools use the snd_pcm_info_get_name() to try to identify PCMs or for
other purposes.
Currently it is left empty with the dmaengine-pcm, in this case copy the
pcm->id string as pcm->name.
For example IGT is using this to find the HDMI PCM for testing audio on it.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Reported-by: Arthur She <arthur.she@linaro.org>
Link: https://lore.kernel.org/r/20190906055524.7393-1-peter.ujfalusi@ti.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
|
|
git://github.com/ojeda/linux
Pull section attribute fix from Miguel Ojeda:
"Fix Oops in Clang-compiled kernels (Nick Desaulniers)"
* tag 'compiler-attributes-for-linus-v5.3-rc8' of git://github.com/ojeda/linux:
include/linux/compiler.h: fix Oops for Clang-compiled kernels
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO fixes from Linus Walleij:
"All related to the PCA953x driver when handling chips with more than 8
ports, now that works again"
* tag 'gpio-v5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio:
gpio: pca953x: use pca953x_read_regs instead of regmap_bulk_read
gpio: pca953x: correct type of reg_direction
|
|
GCC unescapes escaped string section names while Clang does not. Because
__section uses the `#` stringification operator for the section name, it
doesn't need to be escaped.
This fixes an Oops observed in distro's that use systemd and not
net.core.bpf_jit_enable=1, when their kernels are compiled with Clang.
Link: https://github.com/ClangBuiltLinux/linux/issues/619
Link: https://bugs.llvm.org/show_bug.cgi?id=42950
Link: https://marc.info/?l=linux-netdev&m=156412960619946&w=2
Link: https://lore.kernel.org/lkml/20190904181740.GA19688@gmail.com/
Acked-by: Will Deacon <will@kernel.org>
Reported-by: Sedat Dilek <sedat.dilek@gmail.com>
Suggested-by: Josh Poimboeuf <jpoimboe@redhat.com>
Tested-by: Sedat Dilek <sedat.dilek@gmail.com>
Signed-off-by: Nick Desaulniers <ndesaulniers@google.com>
[Cherry-picked from the __section cleanup series for 5.3]
[Adjusted commit message]
Signed-off-by: Miguel Ojeda <miguel.ojeda.sandonis@gmail.com>
|
|
The pci express variant of the digigram lx6464es card has a different
device ID, but works without changes to the driver.
Thanks to Nikolas Slottke for reporting and testing.
Signed-off-by: Tim Blechmann <tim@klingt.org>
Link: https://lore.kernel.org/r/20190906082119.40971-1-tim@klingt.org
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
This reverts commit 558682b5291937a70748d36fd9ba757fb25b99ae.
Chris Wilson reports that it breaks his CPU hotplug test scripts. In
particular, it breaks offlining and then re-onlining the boot CPU, which
we treat specially (and the BIOS does too).
The symptoms are that we can offline the CPU, but it then does not come
back online again:
smpboot: CPU 0 is now offline
smpboot: Booting Node 0 Processor 0 APIC 0x0
smpboot: do_boot_cpu failed(-1) to wakeup CPU#0
Thomas says he knows why it's broken (my personal suspicion: our magic
handling of the "cpu0_logical_apicid" thing), but for 5.3 the right fix
is to just revert it, since we've never touched the LDR bits before, and
it's not worth the risk to do anything else at this stage.
[ Hotpluging of the boot CPU is special anyway, and should be off by
default. See the "BOOTPARAM_HOTPLUG_CPU0" config option and the
cpu0_hotplug kernel parameter.
In general you should not do it, and it has various known limitations
(hibernate and suspend require the boot CPU, for example).
But it should work, even if the boot CPU is special and needs careful
treatment - Linus ]
Link: https://lore.kernel.org/lkml/156785100521.13300.14461504732265570003@skylake-alporthouse-com/
Reported-by: Chris Wilson <chris@chris-wilson.co.uk>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Bandan Das <bsd@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull Documentation updates from Greg KH:
"A few small patches for the documenation file that came in through the
char-misc tree in -rc7 for your tree.
They fix the mistake in the .rst format that kept the table of
companies from showing up in the html output, and most importantly,
add people's names to the list showing support for our process"
* tag 'char-misc-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
Documentation/process: Add Qualcomm process ambassador for hardware security issues
Documentation/process/embargoed-hardware-issues: Microsoft ambassador
Documentation/process: Add Google contact for embargoed hardware issues
Documentation/process: Volunteer as the ambassador for Xen
|
|
issues
Add Trilok Soni as process ambassador for hardware security issues
from Qualcomm.
Signed-off-by: Trilok Soni <tsoni@codeaurora.org>
Link: https://lore.kernel.org/r/1567796517-8964-1-git-send-email-tsoni@codeaurora.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pull dmaengine fixes from Vinod Koul:
"Some late fixes for drivers:
- memory leak in ti crossbar dma driver
- cleanup of omap dma probe
- Fix for link list configuration in sprd dma driver
- Handling fixed for DMACHCLR if iommu is mapped in rcar dma"
* tag 'dmaengine-fix-5.3' of git://git.infradead.org/users/vkoul/slave-dma:
dmaengine: rcar-dmac: Fix DMACHCLR handling if iommu is mapped
dmaengine: sprd: Fix the DMA link-list configuration
dmaengine: ti: omap-dma: Add cleanup in omap_dma_probe()
dmaengine: ti: dma-crossbar: Fix a memory leak bug
|
|
The destructor of AMDTP domain has WARN_ON() for the list of associated
AMDTP stream. Although this reminds a case that developers forget to
program consumer drivers to stop AMDTP domain, it hits when AMDTP domain
is not initialized yet. This occurs when initialization of sound card
fails as well and it's superfluous.
This commit removes the WARN_ON. Although the API to AMDTP domain does
nothing, it's left for future usage.
Fixes: 3ec3d7a3ff106 ("ALSA: firewire-lib: add AMDTP domain structure to handle several isoc contexts")
Signed-off-by: Takashi Sakamoto <o-takashi@sakamocchi.jp>
Link: https://lore.kernel.org/r/20190906131414.15370-1-o-takashi@sakamocchi.jp
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fix from James Bottomley:
"Just a single lpfc fix adjusting the number of available queues for
high CPU count systems"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: lpfc: Raise config max for lpfc_fcp_mq_threshold variable
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fix from Dan Williams:
"Restore support for 1GB alignment namespaces, truncate the end of
misaligned namespaces"
* tag 'libnvdimm-fix-5.3-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/pfn: Fix namespace creation on misaligned addresses
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fix from Dmitry Torokhov:
"A tiny update from Benjamin removing a mistakenly added Elan PNP ID so
that the device is again handled by hid-multitouch"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: elan_i2c - remove Lenovo Legion Y7000 PnpID
|
|
Looks like the Bios of the Lenovo Legion Y7000 is using ELAN061B
when the actual device is supposed to be used with hid-multitouch.
Remove it from the list of the supported device, hoping that
no one will complain about the loss in functionality.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=203467
Fixes: 738c06d0e456 ("Input: elan_i2c - add hardware ID for multiple Lenovo laptops")
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Arnd Bergmann:
"There are three more fixes for this week:
- The Windows-on-ARM laptops require a workaround to prevent crashing
at boot from ACPI
- The Renesas 'draak' board needs one bugfix for the backlight
regulator
- Also for Renesas, the 'hihope' board accidentally had its eMMC
turned off in the 5.3 merge window"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
soc: qcom: geni: Provide parameter error checking
arm64: dts: renesas: hihope-common: Fix eMMC status
arm64: dts: renesas: r8a77995: draak: Fix backlight regulator name
|
|
Pull configfs fixes from Christoph Hellwig:
"Late configfs fixes from Al that fix pretty nasty removal vs attribute
access races"
* tag 'configfs-for-5.3' of git://git.infradead.org/users/hch/configfs:
configfs: provide exclusion between IO and removals
configfs: new object reprsenting tree fragments
configfs_register_group() shouldn't be (and isn't) called in rmdirable parts
configfs: stash the data we need into configfs_buffer at open time
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU fixes from Joerg Roedel:
- Revert an Intel VT-d patch that caused problems for some users.
- Removal of a feature in the Intel VT-d driver that was never
supported in hardware. This qualifies as a fix because the code for
this feature sets reserved bits in the invalidation queue descriptor,
causing failed invalidations on real hardware.
- Two fixes for AMD IOMMU driver to fix a race condition and to add a
missing IOTLB flush when kernel is booted in kdump mode.
* tag 'iommu-fixes-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu:
iommu/amd: Fix race in increase_address_space()
iommu/amd: Flush old domains in kdump kernel
iommu/vt-d: Remove global page flush support
Revert "iommu/vt-d: Avoid duplicated pci dma alias consideration"
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc
Pull MMC fix from Ulf Hansson:
"Revert in order to fix card init for some eMMCs that need retries for
CMD6"
* tag 'mmc-v5.3-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/ulfh/mmc:
Revert "mmc: core: do not retry CMD6 in __mmc_switch()"
|
|
Pull drm fixes from Dave Airlie:
"Live from my friend's couch in Barcelona, latest round of drm fixes.
The command line parser regression fixes look a bit larger because
they come with selftests included for the bugs they fix. Otherwise a
single nouveau, single ingenic and single vmwgfx fix:
nouveau:
- add missing MODULE_FIRMWARE definitions
igenic:
- hardcode panel type DPI
vmwgfx:
- double free fix
core:
- command line mode parser fixes"
* tag 'drm-fixes-2019-09-06' of git://anongit.freedesktop.org/drm/drm:
drm/vmwgfx: Fix double free in vmw_recv_msg()
drm/nouveau/sec2/gp102: add missing MODULE_FIRMWAREs
drm/selftests: modes: Add more unit tests for the cmdline parser
drm/modes: Introduce a whitelist for the named modes
drm/modes: Fix the command line parser to take force options into account
drm/modes: Add a switch to differentiate free standing options
drm/ingenic: Hardcode panel type to DPI
|
|
Pull virtio fixes from Michael Tsirkin:
"virtio, vhost, and balloon bugfixes.
A couple of last minute bugfixes. And a revert of a failed attempt at
metadata access optimization - we'll try again in the next cycle"
* tag 'for_linus' of git://git.kernel.org/pub/scm/linux/kernel/git/mst/vhost:
mm/balloon_compaction: suppress allocation warnings
Revert "vhost: access vq metadata through kernel virtual address"
vhost: Remove unnecessary variable
virtio-net: lower min ring num_free for efficiency
vhost/test: fix build for vhost test
vhost/test: fix build for vhost test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"One fix for a boot hang on some Freescale machines when PREEMPT is
enabled.
Two CVE fixes for bugs in our handling of FP registers and
transactional memory, both of which can result in corrupted FP state,
or FP state leaking between processes.
Thanks to: Chris Packham, Christophe Leroy, Gustavo Romero, Michael
Neuling"
* tag 'powerpc-5.3-5' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc/tm: Fix restoring FP/VMX facility incorrectly on interrupts
powerpc/tm: Fix FP/VMX unavailable exceptions inside a transaction
powerpc/64e: Drop stale call to smp_processor_id() which hangs SMP startup
|
