| Age | Commit message (Collapse) | Author |
|---|
|
The current IRQ coalescing logic is a little messy. The ethtool
parameters are mapped to hardware parameters in a way that is difficult
to understand. The first step is to better organize the parameters
by adding the new structure bnxt_coal. The structure is used by both
the RX and TX sets of coalescing parameters.
Adjust the default coal_ticks to 14 us and 28 us for RX and TX.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a firmware internal reset after driver is unloaded.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some NICs have a firmware enforced maximum MTU setting by management
firmware. Set up netdev->max_mtu accordingly.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No need to call bnxt_approve_mac() which will send a message to the
PF if the MAC address hasn't changed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code retrieves the firmware package version from firmware
everytime ethtool -i is run. There is no reason to do that as the
firmware will not change while the driver is loaded. Get the version
once at init time.
Also, display the full 4-part firmware version string and remove the
less useful interface spec version.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return -EINVAL if the length is zero and not proceed to do essentially
nothing.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rob Miller <rmiller@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add new PCIe device ID and chip number for bcm58804
Signed-off-by: Ray Jui <ray.jui@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vxlan encap/decap filters are added to this firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Vivien Didelot says:
====================
net: dsa: define port types
The DSA code currently has 3 bitmaps in the dsa_switch structure:
cpu_port_mask, dsa_port_mask and enabled_port_mask.
They are used to store the type of each switch port. This dates back
from when DSA didn't have a dsa_port structure to hold port-specific
data.
The dsa_switch structure is mainly used to communicate with DSA drivers
and must not contain such static data parsed from DTS or pdata, which
belongs the DSA core structures, such as dsa_switch_tree and dsa_port.
Also the enabled_port_mask is misleading, often misinterpreted as the
complement of disabled ports (thus including DSA and CPU ports), while
in fact it only masks the user ports.
A port can be of 3 types when it is not unused: "cpu" (interfacing with
a master device), "dsa" (interconnecting with another "dsa" port from
another switch chip), or "user" (user-facing port.)
This patchset first fixes the usage of DSA port type helpers, then
defines the DSA_PORT_TYPE_UNUSED, DSA_PORT_TYPE_CPU, DSA_PORT_TYPE_DSA,
and DSA_PORT_TYPE_USER port types, and finally removes the misleading
port bitmaps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that DSA core provides port types, there is no need to keep this
information at the switch level. This is a static information that is
part of a DSA core dsa_port structure. Remove them.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that DSA exposes an enumerated type for the ports, we can use them
directly instead of checking bitmaps, which is more consistent.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce an enumerated type for ports, which will be way more explicit
to identify a port type instead of digging into switch port masks.
A port can be of type CPU, DSA, user, or unused by default. This is a
static parsed information that cannot be changed at runtime.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a dsa_user_ports() helper to return the ds->enabled_port_mask
mask which is more explicit. This will also minimize diffs when touching
this internal mask.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Most of the DSA code still check ds->enabled_port_mask directly to
inspect a given port type instead of using the provided dsa_is_user_port
helper. Change this.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch renames dsa_is_normal_port to dsa_is_user_port because "user"
is the correct term in the DSA terminology, not "normal".
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to know if a port is of type user, dsa_is_normal_port checks
that the given port is not of type DSA nor CPU. This is not enough
because a port can be unused.
Without the previous fix, this caused the unused mv88e6xxx ports to be
configured in normal mode.
The ds->enabled_port_mask reports the user ports, so check this instead.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The unused ports are currently configured in normal mode. This does not
prevent the switch from being functional, but it is unnecessary. Skip
unused ports.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As the comment above the chunk states, the b53 driver attempts to
disable the unused ports. But using ds->enabled_port_mask is misleading,
because this mask reports in fact the user ports.
To avoid confusion and fix this, this patch introduces an explicit
dsa_is_unused_port helper which ensures the corresponding bit is not
masked in any of the switch port masks.
Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Notice that in this particular case unlikely() is already being called
inside BUG_ON macro.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use BUG_ON instead of if condition followed by BUG.
Something to notice in this particular case is that unlikely()
is already being called inside BUG_ON macro.
This issue was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rahul Lakkireddy says:
====================
cxgb4: collect more hardware dumps via ethtool
This series of patches collect more firmware and hardware dumps
via ethool --get-dump facility.
Patch 1 collects hardware logic analyzer dumps.
Patch 2 collects CIM queue configuration dump.
Patch 3 collects RSS dumps.
Patch 4 collects TID info dump.
Patch 5 collects MPS-TCAM dump.
Patch 6 collects PBT tables dump.
Patch 7 collects hardware scheduler and pace table dumps.
Patch 8 collects miscellaneous hardware information, including
path mtu, PM stats, TP clock info, congestion control, and VPD
data dumps.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect path mtu, PM stats, TP clock info, congestion control, and VPD
data dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect hardware TX traffic scheduler and pace tables.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect RSS table and RSS VF configuration dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Collect CIM, CIM_MA, ULP_RX, TP, CIM_PIF, and ULP_TX logic analyzer
dumps.
Signed-off-by: Rahul Lakkireddy <rahul.lakkireddy@chelsio.com>
Signed-off-by: Ganesh Goudar <ganeshgr@chelsio.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a Toobig icmpv6 packet, ip6gre_err would just set
tunnel dev's mtu, that's not enough. For skb_dst(skb)'s pmtu may
still be using the old value, it has no chance to be updated with
tunnel dev's mtu.
Jianlin found this issue by reducing route's mtu while running
netperf, the performance went to 0.
ip6ip6 and ip4ip6 tunnel can work well with this, as they lookup
the upper dst and update_pmtu it's pmtu or icmpv6_send a Toobig
to upper socket after setting tunnel dev's mtu.
We couldn't do that for ip6_gre, as gre's inner packet could be
any protocol, it's difficult to handle them (like lookup upper
dst) in a good way.
So this patch is to fix it by updating skb_dst(skb)'s pmtu when
dev->mtu < skb_dst(skb)'s pmtu in tx path. It's safe to do this
update there, as usually dev->mtu <= skb_dst(skb)'s pmtu and no
performance regression can be caused by this.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The similar fix in patch 'ipip: only increase err_count for some
certain type icmp in ipip_err' is needed for ip6gre_err.
In Jianlin's case, udp netperf broke even when receiving a TooBig
icmpv6 packet.
Fixes: c12b395a4664 ("gre: Support GRE over IPv6")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
t->err_count is used to count the link failure on tunnel and an err
will be reported to user socket in tx path if t->err_count is not 0.
udp socket could even return EHOSTUNREACH to users.
Since commit fd58156e456d ("IPIP: Use ip-tunneling code.") removed
the 'switch check' for icmp type in ipip_err(), err_count would be
increased by the icmp packet with ICMP_EXC_FRAGTIME code. an link
failure would be reported out due to this.
In Jianlin's case, when receiving ICMP_EXC_FRAGTIME a icmp packet,
udp netperf failed with the err:
send_data: data send error: No route to host (errno 113)
We expect this error reported from tunnel to socket when receiving
some certain type icmp, but not ICMP_EXC_FRAGTIME, ICMP_SR_FAILED
or ICMP_PARAMETERPROB ones.
This patch is to bring 'switch check' for icmp type back to ipip_err
so that it only reports link failure for the right type icmp, just as
in ipgre_err() and ipip6_err().
Fixes: fd58156e456d ("IPIP: Use ip-tunneling code.")
Reported-by: Jianlin Shi <jishi@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
According to DWMAC databook the first queue operating mode
must always be in DCB.
As MTL_QUEUE_DCB = 1, we need to always set the first queue
operating mode to DCB otherwise driver will think that queue
is in AVB mode (because MTL_QUEUE_AVB = 0).
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Egil Hjelmeland says:
====================
net: dsa: lan9303: Learn addresses on CPU port when bridged
When CPU transmit directly to port using tag, the LAN9303 does not
learn MAC addresses received on the CPU port into the ALR table.
ALR learning is performed only when transmitting using ALR lookup.
Solution:
If the two external ports are bridged and the packet is not STP BPDU,
then use ALR lookup to allow ALR learning on CPU port.
Otherwise transmit directly to port with STP state override.
The first patch moves struct lan9303 to include/linux/dsa/lan9303.h in
order to prepare for the second patch.
Changes v1 -> v2:
- new file: include/linux/dsa/lan9303.h instead of include/linux/lan9303.h
- include linux/if_ether.h in include/linux/dsa/lan9303.h
- renamed lan9303_tx_use_arl to lan9303_xmit_use_arl for consistency.
- removed inline keyword to lan9303_xmit_use_arl
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CPU transmit directly to port using tag, the LAN9303 does not
learn MAC addresses received on the CPU port into the ALR.
ALR learning is performed only when transmitting using ALR lookup.
Solution:
If the two external ports are bridged and the packet is not STP BPDU,
then use ALR lookup to allow ALR learning on CPU port.
Otherwise transmit directly to port with STP state override.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The next patch require net/dsa/tag_lan9303.c to access struct lan9303.
Therefore move struct lan9303 definitions from drivers/net/dsa/lan9303.h
to new file include/linux/dsa/lan9303.h.
Signed-off-by: Egil Hjelmeland <privat@egil-hjelmeland.no>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jiri Pirko says:
====================
mlxsw: small cleanup
Couple of small cleanup patches from Nogah.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace recurring magic number in PPCNT register with a define.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the HW stats cache to be local. Rename it for better clarity.
It holds the results of the last result of HW stats that are being read
periodically, in order to have answer for stats request immediately.
Signed-off-by: Nogah Frankel <nogahf@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid that submitting an SG_IO ioctl triggers a kernel oops that
is preceded by:
usercopy: kernel memory overwrite attempt detected to (null) (<null>) (6 bytes)
kernel BUG at mm/usercopy.c:72!
Reported-by: Dann Frazier <dann.frazier@canonical.com>
Fixes: commit ca18d6f769d2 ("block: Make most scsi_req_init() calls implicit")
Signed-off-by: Bart Van Assche <bart.vanassche@wdc.com>
Cc: Michael S. Tsirkin <mst@redhat.com>
Cc: Dann Frazier <dann.frazier@canonical.com>
Cc: <stable@vger.kernel.org> # v4.13
Reviewed-by: Christoph Hellwig <hch@lst.de>
Moved virtblk_initialize_rq() inside CONFIG_VIRTIO_BLK_SCSI.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
According to DT bindings documentation we are expecting a
property called "snps,read-requests" but we are parsing
instead a property called "read,read-requests".
This is clearly a typo. Fix it.
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull an NVMe fix from Christoph.
|
|
No rcu_read_lock is called, but rcu_read_unlock is still called.
Thus rcu_read_unlock should be removed.
Signed-off-by: Jia-Ju Bai <baijiaju1990@163.com>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Kalle Valo <kvalo@qca.qualcomm.com>
Cc: linux-wireless@vger.kernel.org
Cc: netdev@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This driver shouldn't be using wdev->ssid to start with, as
it's more or less an internal field in cfg80211 used for
various purposes. Reading it is possible through nl80211,
even if that's not really what we should be doing there
for anything but AP type interfaces.
It *really* shouldn't allow modifying it!
Remove the whole debugfs entry.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
This file doesn't exist.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
Variable val is unsigned, so checking whether it is less than zero is
redundant.
Signed-off-by: Christos Gkekas <chris.gekas@gmail.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
|
The current firmware 10.4-3.5.1-00035 on QCA9888 supports
TDLS explicit mode, it expects WMI_TDLS_ENABLE_PASSIVE
for tdls setup and WMI_TDLS_DISABLE for tdls teardown.
Signed-off-by: Anilkumar Kolli <akolli@qti.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
