summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2017-02-14Merge branch 'ipv6-v4mapped'David S. Miller
Jonathan T. Leighton says: ==================== IPv4-mapped on wire, :: dst address issue Under some circumstances IPv6 datagrams are sent with IPv4-mapped IPv6 addresses as the source. Given an IPv6 socket bound to an IPv4-mapped IPv6 address, and an IPv6 destination address, both TCP and UDP will will send packets using the IPv4-mapped IPv6 address as the source. Per RFC 6890 (Table 20), IPv4-mapped IPv6 source addresses are not allowed in an IP datagram. The problem can be observed by attempting to connect() either a TCP or UDP socket, or by using sendmsg() with a UDP socket. The patch is intended to correct this issue for all socket types. linux follows the BSD convention that an IPv6 destination address specified as in6addr_any is converted to the loopback address. Currently, neither TCP nor UDP consider the possibility that the source address is an IPv4-mapped IPv6 address, and assume that the appropriate loopback address is ::1. The patch adds a check on whether or not the source address is an IPv4-mapped IPv6 address and then sets the destination address to either ::ffff:127.0.0.1 or ::1, as appropriate. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14ipv6: Handle IPv4-mapped src to in6addr_any dst.Jonathan T. Leighton
This patch adds a check on the type of the source address for the case where the destination address is in6addr_any. If the source is an IPv4-mapped IPv6 source address, the destination is changed to ::ffff:127.0.0.1, and otherwise the destination is changed to ::1. This is done in three locations to handle UDP calls to either connect() or sendmsg() and TCP calls to connect(). Note that udpv6_sendmsg() delays handling an in6addr_any destination until very late, so the patch only needs to handle the case where the source is an IPv4-mapped IPv6 address. Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14ipv6: Inhibit IPv4-mapped src address on the wire.Jonathan T. Leighton
This patch adds a check for the problematic case of an IPv4-mapped IPv6 source address and a destination address that is neither an IPv4-mapped IPv6 address nor in6addr_any, and returns an appropriate error. The check in done before returning from looking up the route. Signed-off-by: Jonathan T. Leighton <jtleight@udel.edu> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14spi: lantiq-ssc: add support for Lantiq SSC SPI controllerHauke Mehrtens
This driver supports the Lantiq SSC SPI controller in master mode. This controller is found on Intel (former Lantiq) SoCs like the Danube, Falcon, xRX200, xRX300. The hardware uses two hardware FIFOs one for received and one for transferred bytes. When the driver writes data into the transmit FIFO the complete word is taken from the FIFO into a shift register. The data from this shift register is then written to the wire. This driver uses the interrupts signaling the status of the FIFOs and not the shift register. It is also possible to use the interrupts for the shift register, but they will send a signal after every word. When using the interrupts for the shift register we get a signal when the last word is written into the shift register and not when it is written to the wire. After all FIFOs are empty the driver busy waits till the hardware is not busy any more and returns the transfer status. Signed-off-by: Daniel Schwierzeck <daniel.schwierzeck@gmail.com> Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de> Signed-off-by: Mark Brown <broonie@kernel.org>
2017-02-14staging: comedi: ni_pcimio: remove unused variable 'serial_number'Karthik Nayak
The struct 'ni_private' holds the variable 'serial_number' which post assignment is never used. Remove the variable and code pertaining to obtaining its value. As a side note, this also fixes the following sparse error: drivers/staging/comedi/drivers//ni_pcimio.c:1229:32: warning: incorrect type in assignment (different base types) drivers/staging/comedi/drivers//ni_pcimio.c:1229:32: expected restricted __be32 [usertype] serial_number drivers/staging/comedi/drivers//ni_pcimio.c:1229:32: got unsigned int Signed-off-by: Karthik Nayak <Karthik.188@gmail.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14staging: comedi: dyna_pci10xx: usleep_range is preferred over udelaySaber Rezvani
Fix the checkpatch.pl issue: CHECK: usleep_range is preferred over udelay Signed-off-by: Saber Rezvani <irsaber@gmail.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14staging: comedi: s626: usleep_range is preferred over udelaySaber Rezvani
Fix the checkpatch.pl issue: CHECK: usleep_range is preferred over udelay Signed-off-by: Saber Rezvani <irsaber@gmail.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14staging: comedi: ni_pcidio.c: Spaces preferred around operatorsSaber Rezvani
Fix the checkpatch.pl issue: CHECK: spaces preferred around that '|' (ctx:VxV) Signed-off-by: Saber Rezvani <irsaber@gmail.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14staging: comedi: ni_pcidio: blank line issuesSaber Rezvani
Fix the checkpatch.pl issue: CHECK: Please use a blank line after function/struct/union/enum declarations Signed-off-by: Saber Rezvani <irsaber@gmail.com> Reviewed-by: Ian Abbott <abbotti@mev.co.uk> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2017-02-14net/mlx5e: Disable preemption when doing TC statistics upcallOr Gerlitz
When called by HW offloading drivers, the TC action (e.g net/sched/act_mirred.c) code uses this_cpu logic, e.g _bstats_cpu_update(this_cpu_ptr(a->cpu_bstats), bytes, packets) per the kernel documention, preemption should be disabled, add that. Before the fix, when running with CONFIG_PREEMPT set, we get a BUG: using smp_processor_id() in preemptible [00000000] code: tc/3793 asserion from the TC action (mirred) stats_update callback. Fixes: aad7e08d39bd ('net/mlx5e: Hardware offloaded flower filter statistics support') Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14net:dsa:mv88e6xxx: use watchdog ops for 6097 chipVolodymyr Bendiuga
mv88e6097 chip requires watchdog_ops to be set. Signed-off-by: Volodymyr Bendiuga <volodymyr.bendiuga@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14IB/mlx4: Take source GID by index from HW GID tableTalat Batheesh
Previously, we used the HW GID index in order to search the source GID in the software GID cached table. In some cases, for example when the MAC Address of the network interface is changed, the GID cached table saves the old-IPv6-link-local GID at the end of the table. When returning the old MAC address, the software GID cached table tries to add the new IPv6-link-local GID, and when it identifies that the GID already exists, the software GID cached does not add it. Thus a mismatch occurs between the HW and the SW GID tables. It resulted with sending traffic with the wrong source GID. This commit fixes the issue by taking both from the HW table. The problem can be reproduced with the following scenario: Client: # ifconfig ens6 2.2.2.5 # ifconfig ens6 inet6 add 2001:0db8:0:f101::5/64 # ifconfig ens6 hw ether f4:52:14:61:a0:71 # ifconfig ens6 inet6 del 2001:0db8:0:f101::5/64 # ifconfig ens6 inet6 add 2001:0db8:0:f101::5/64 # ucmatose -f ipv6 -b 2001:0db8:0:f101::5 -s 2001:0db8:0:f101::6 -p 20156 Server: # ucmatose -f ipv6 -b 2001:0db8:0:f101::6 -p 20156 Fixes: 4c3eb3ca1396 ('IB/mlx4: Add VLAN support for IBoE') Signed-off-by: Talat Batheesh <talatb@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Fix blue flame buffer size calculationEli Cohen
A blue flame register is comprised of two buffers of equal size. Fixes: 5fe9dec0d0454 ("IB/mlx5: Use blue flame register allocator in mlx5_ib") Signed-off-by: Eli Cohen <eli@mellanox.com> Reviewed-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx4: Remove unused variable from function declarationLeon Romanovsky
Remove unused netw_view parameter from eth_link_query_port() function. Reported-by: Shiraz Saleem <shiraz.saleem@intel.com> Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14sched: Fix accidental removal of errout gotoJiri Pirko
Bring back the goto that was removed by accident. Reported-by: Colin Ian King <colin.king@canonical.com> Fixes: 40c81b25b16c ("sched: check negative err value to safe one level of indent") Signed-off-by: Jiri Pirko <jiri@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-02-14IB: Query ports via the core instead of direct into the driverOr Gerlitz
Change the drivers to call ib_query_port in their get port immutable handler instead of their own query port handler. Doing this required to set the core cap flags of this device before the ib_query_port call is made, since the IB core might need these caps to serve the port query. Drivers are ensured by the IB core that the port attributes passed to the port query verb implementation are zero, and hence we removed the zeroing from the drivers. This patch doesn't add any new functionality. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Steve Wise <swise@opengridcomputing.com> Acked-by: Adit Ranadive <aditr@vmware.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB: Add protocol for USNICOr Gerlitz
Add protocol definition for the proprietary the USNIC driver. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Christian Benvenuti <benve@cisco.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx4: Support raw packet protocolOr Gerlitz
Mark support for the new raw packet protocol on Eth ports. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Support raw packet protocolOr Gerlitz
Mark support for the new raw packet protocol on Eth ports. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Add raw packet protocolOr Gerlitz
Define raw packet protocol which comes to denote this port supports working with raw ethernet frames, e.g as done with RAW_PACKET QPs. Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com> Reviewed-by: Matan Barak <matanb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Steve Wise <swise@opengridcomputing.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Add implicit MR supportArtemy Kovalyov
Add implicit MR, covering entire user address space. The MR is implemented as an indirect KSM MR consisting of 1GB direct MRs. Pages and direct MRs are added/removed to MR by ODP. Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Expose MR cache for mlx5_ibArtemy Kovalyov
Allow other parts of mlx5_ib to use MR cache mechanism. * Add new functions mlx5_mr_cache_alloc and mlx5_mr_cache_free * Traditional MTT MKey buckets are limited by MAX_UMR_CACHE_ENTRY Additinal buckets may be added above. Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Add null_mkey accessArtemy Kovalyov
Add mlx5_cmd_null_mkey() function to access null_mkey information from firmware. Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/umem: Indicate that process is being terminatedArtemy Kovalyov
When process is killed while pagefault operation still in progress - function will fail. In this specific case we don't want any warnings in dmesg to avoid log analyzers false alerts. So we need distinct error code for this case. Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/umem: Update on demand page (ODP) supportArtemy Kovalyov
Currently ODP MR may explicitly register virtual address space area of limited length. This change allows MR to cover entire process virtual address space dynamicaly adding/removing translation entries to device MTT. Add following changes to support implicit MR: * Allow umem to be zero size to back-up implicit MR. * Add new function ib_alloc_odp_umem() to add virtual memory regions to implicit MR dynamically on demand. * Add new function rbt_ib_umem_lookup() to find dynamically added virtual memory regions. * Expose function rbt_ib_umem_for_each_in_range() to other modules and make it safe Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Add implicit MR flagArtemy Kovalyov
Add flag IB_ODP_SUPPORT_IMPLICIT indicating implicit MR supported. Signed-off-by: Artemy Kovalyov <artemyko@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Support creation of a WQ with scatter FCS offloadNoa Osherovich
Add support for creation of a WQ with scatter FCS capability, if this capability is supported by the hardware. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Majd Dibbiny <majd@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Enable QP creation with cvlan offloadNoa Osherovich
Enable creating a RAW Ethernet QP with cvlan stripping offload when it's supported by the hardware. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Enable WQ creation and modification with cvlan offloadNoa Osherovich
Allow creating a WQ with cvlan stripping considering device's capabilities. The default value was fixed to disable vlan stripping till was asked explicitly. In addition, allow modification of a WQ to turn on/off this property. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Expose vlan offloads capabilitiesNoa Osherovich
Check device's capabilities and report which raw packet capabilities are supported. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/uverbs: Enable QP creation with cvlan offloadNoa Osherovich
Enable user applications to create a QP with cvlan stripping offload. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/uverbs: Enable WQ creation and modification with cvlan offloadNoa Osherovich
Enable user space application via WQ creation and modification to turn on and off cvlan offload. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/uverbs: Expose vlan offloads capabilitiesNoa Osherovich
Expose raw packet capabilities to user space as part of query device. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Add scatter FCS flag to use in WQ creationNoa Osherovich
Add a new creation flag to set the scatter FCS capability of a WQ. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Majd Dibbiny <majd@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Enable QP creation with cvlan offloadNoa Osherovich
Add a QP creation flag to support cvlan stripping, it's applicable for RAW Ethernet QP. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Enable WQ creation and modification with cvlan offloadNoa Osherovich
Enable WQ creation and modification with cvlan stripping offload. This includes: - Adding WQ creation flags. - Extending modify WQ to get flags and flags mask to enable turning it on and off. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Expose vlan offloads capabilitiesNoa Osherovich
Expose raw packet capabilities in the core layer to enable a device to report it. Two existing capabilities, scatter FCS and IP CSUM were added to this field for a better user experience by exposing the raw packet caps from one location. This field will serve also for future capabilities for raw packet QP. A new capability was introduced - cvlan stripping, which is the device's ability to remove cvlan tag from an incoming packet and report it in the matching work completion. Signed-off-by: Noa Osherovich <noaos@mellanox.com> Reviewed-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Yishai Hadas <yishaih@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Add port counter support for Receive WQsMajd Dibbiny
Counters weren't updated due to Receive WQs' traffic since the counter-id was not associated with the RQ. Added support for associating the q-counter-id with the Receive WQ. The attachment is done only when changing WQ's state from RESET to READY in modify-WQ command. FW support is required for the above, without this support Receive WQ counters will not count. Signed-off-by: Majd Dibbiny <majd@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Expose Q counters groups only if they are supported by FWKamal Heib
This patch modify the Q counters implementation, so each one of the three Q counters groups will be exposed by the driver only if they are supported by the firmware. Signed-off-by: Kamal Heib <kamalh@mellanox.com> Reviewed-by: Mark Bloch <markb@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14ext4: don't BUG when truncating encrypted inodes on the orphan listTheodore Ts'o
Fix a BUG when the kernel tries to mount a file system constructed as follows: echo foo > foo.txt mke2fs -Fq -t ext4 -O encrypt foo.img 100 debugfs -w foo.img << EOF write foo.txt a set_inode_field a i_flags 0x80800 set_super_value s_last_orphan 12 quit EOF root@kvm-xfstests:~# mount -o loop foo.img /mnt [ 160.238770] ------------[ cut here ]------------ [ 160.240106] kernel BUG at /usr/projects/linux/ext4/fs/ext4/inode.c:3874! [ 160.240106] invalid opcode: 0000 [#1] SMP [ 160.240106] Modules linked in: [ 160.240106] CPU: 0 PID: 2547 Comm: mount Tainted: G W 4.10.0-rc3-00034-gcdd33b941b67 #227 [ 160.240106] Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.1-1 04/01/2014 [ 160.240106] task: f4518000 task.stack: f47b6000 [ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4 [ 160.240106] EFLAGS: 00010246 CPU: 0 [ 160.240106] EAX: 00000001 EBX: f7be4b50 ECX: f47b7dc0 EDX: 00000007 [ 160.240106] ESI: f43b05a8 EDI: f43babec EBP: f47b7dd0 ESP: f47b7dac [ 160.240106] DS: 007b ES: 007b FS: 00d8 GS: 0033 SS: 0068 [ 160.240106] CR0: 80050033 CR2: bfd85b08 CR3: 34a00680 CR4: 000006f0 [ 160.240106] Call Trace: [ 160.240106] ext4_truncate+0x1e9/0x3e5 [ 160.240106] ext4_fill_super+0x286f/0x2b1e [ 160.240106] ? set_blocksize+0x2e/0x7e [ 160.240106] mount_bdev+0x114/0x15f [ 160.240106] ext4_mount+0x15/0x17 [ 160.240106] ? ext4_calculate_overhead+0x39d/0x39d [ 160.240106] mount_fs+0x58/0x115 [ 160.240106] vfs_kern_mount+0x4b/0xae [ 160.240106] do_mount+0x671/0x8c3 [ 160.240106] ? _copy_from_user+0x70/0x83 [ 160.240106] ? strndup_user+0x31/0x46 [ 160.240106] SyS_mount+0x57/0x7b [ 160.240106] do_int80_syscall_32+0x4f/0x61 [ 160.240106] entry_INT80_32+0x2f/0x2f [ 160.240106] EIP: 0xb76b919e [ 160.240106] EFLAGS: 00000246 CPU: 0 [ 160.240106] EAX: ffffffda EBX: 08053838 ECX: 08052188 EDX: 080537e8 [ 160.240106] ESI: c0ed0000 EDI: 00000000 EBP: 080537e8 ESP: bfa13660 [ 160.240106] DS: 007b ES: 007b FS: 0000 GS: 0033 SS: 007b [ 160.240106] Code: 59 8b 00 a8 01 0f 84 09 01 00 00 8b 07 66 25 00 f0 66 3d 00 80 75 61 89 f8 e8 3e e2 ff ff 84 c0 74 56 83 bf 48 02 00 00 00 75 02 <0f> 0b 81 7d e8 00 10 00 00 74 02 0f 0b 8b 43 04 8b 53 08 31 c9 [ 160.240106] EIP: ext4_block_zero_page_range+0x1a7/0x2b4 SS:ESP: 0068:f47b7dac [ 160.317241] ---[ end trace d6a773a375c810a5 ]--- The problem is that when the kernel tries to truncate an inode in ext4_truncate(), it tries to clear any on-disk data beyond i_size. Without the encryption key, it can't do that, and so it triggers a BUG. E2fsck does *not* provide this service, and in practice most file systems have their orphan list processed by e2fsck, so to avoid crashing, this patch skips this step if we don't have access to the encryption key (which is the case when processing the orphan list; in all other cases, we will have the encryption key, or the kernel wouldn't have allowed the file to be opened). An open question is whether the fact that e2fsck isn't clearing the bytes beyond i_size causing problems --- and if we've lived with it not doing it for so long, can we drop this from the kernel replay of the orphan list in all cases (not just when we don't have the key for encrypted inodes). Addresses-Google-Bug: #35209576 Signed-off-by: Theodore Ts'o <tytso@mit.edu>
2017-02-14cdrom: Make device operations read-onlyKees Cook
Since function tables are a common target for attackers, it's best to keep them in read-only memory. As such, this makes the CDROM device ops tables const. This drops additionally n_minors, since it isn't used meaningfully, and sets the only user of cdrom_dummy_generic_packet explicitly so the variables can all be const. Inspired by similar changes in grsecurity/PaX. Signed-off-by: Kees Cook <keescook@chromium.org> Acked-by: David S. Miller <davem@davemloft.net> Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-14IB/mlx5: Replace ENOTSUPP usage with EOPNOTSUPPLeon Romanovsky
Flow steering is supposed to return EOPNOTSUPP error for unsupported fields and not ENOTSUPP error. Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Add flow tag supportMoses Reuben
Set flow tag in flow table entry, when IB_FLOW_SPEC_ACTION_TAG is part of the flow specifications. Flow tag doesn't support multicast flows, so it's passing to hardware only when used. Signed-off-by: Moses Reuben <mosesr@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/uverbs: Add support for flow tagMoses Reuben
The struct ib_uverbs_flow_spec_action_tag associates a tag_id with the flow defined by any number of other flow_spec entries which can reference L2, L3, and L4 packet contents. Use of ib_uverbs_flow_spec_action_tag allows the consumer to identify the set of rules which where matched by the packet by examining the tag_id in the CQE. Signed-off-by: Moses Reuben <mosesr@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/core: Introduce flow tag specificationMoses Reuben
This specification identifies flow with a specific tag-id. This tag-id will be reported in the CQE. Signed-off-by: Moses Reuben <mosesr@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14net/mlx5: Consolidate flow rules regardless their flow tagMaor Gottlieb
Flow rules with same match criteria and value should be mapped to the same flow table entry regardless the flow tag identifier. Flow tag is part of flow table entry context and not of the destination, therefore we should return error when we try to add destination to flow table entry with different flow tag. Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14elevator: fix loading wrong elevator type for blk-mq devicesJens Axboe
The old elevator= boot parameter blindly attempts to load the same scheduler for mq and !mq devices, leading to a crash if we specify the wrong one. Ensure that we only apply this boot parameter to old !mq devices. Signed-off-by: Jens Axboe <axboe@fb.com>
2017-02-14IB/mlx5: Remove deprecated module parameterLeon Romanovsky
Commit 9603b61de1ee ("mlx5: Move pci device handling from mlx5_ib to mlx5_core") moved prof_sel module parameter from mlx5_ib to mlx5_core and marked it as deprecated in 2014. Three years after deprecation, it is time to remove the deprecated module parameter. Signed-off-by: Leon Romanovsky <leonro@mellanox.com> Reviewed-by: Jack Morgenstein <jackm@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Assign DSCP for R-RoCE QPs Address PathMajd Dibbiny
For Routable RoCE QPs, the DSCP should be set in the QP's address path. The DSCP's value is derived from the traffic class. Fixes: 2811ba51b049 ("IB/mlx5: Add RoCE fields to Address Vector") Cc: Achiad Shochat <achiad@mellanox.com> Signed-off-by: Majd Dibbiny <majd@mellanox.com> Reviewed-by: Moni Shoua <monis@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com> Signed-off-by: Doug Ledford <dledford@redhat.com>
2017-02-14IB/mlx5: Avoid SMP MADs from VFsMaor Gottlieb
According to the device specification, we need to check that the has_smi bit is set in vport context before allowing send SMP MADs from VF. Fixes: e126ba97dba9 ('mlx5: Add driver for Mellanox Connect-IB adapters') Signed-off-by: Maor Gottlieb <maorg@mellanox.com> Reviewed-by: Eli Cohen <eli@mellanox.com> Signed-off-by: Leon Romanovsky <leon@kernel.org> Signed-off-by: Doug Ledford <dledford@redhat.com>
generated by cgit (git 2.34.1) at 2025-09-23 04:47:43 +0000