| Age | Commit message (Collapse) | Author |
|---|
|
In case of error, the function devm_ioremap() returns NULL pointer not
ERR_PTR(). The IS_ERR() test in the return value check should be
replaced with NULL test.
Fixes: 091876cc355d ("phy: ti: j721e-wiz: Add support for WIZ module present in TI J721E SoC")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
|
|
While fixing another issue in this driver I noticed it uses
IS_ERR_OR_NULL(), which is almost always a mistake.
Change the driver to use the proper devm_reset_control_get_optional()
interface instead and remove the checks except for the one that
checks for a failure in that function.
Fixes: 2b2c47d9e1fe ("ata: ahci_brcm: Allow optional reset controller to be used")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The new shutdown callback causes a link failure:
drivers/ata/ahci_brcm.c: In function 'brcm_ahci_shutdown':
drivers/ata/ahci_brcm.c:552:8: error: implicit declaration of function 'brcm_ahci_suspend'; did you mean 'brcm_ahci_shutdown'? [-Werror=implicit-function-declaration]
ret = brcm_ahci_suspend(&pdev->dev);
^~~~~~~~~~~~~~~~~
Remove the incorrect #ifdef and use __maybe_unused annotations
instead to make this more robust.
Fixes: 7de9b1688c1d ("ata: ahci_brcm: Add a shutdown callback")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the credentials or the mm doesn't match, don't allow the task to
submit anything on behalf of this ring. The task that owns the ring can
pass the file descriptor to another task, but we don't want to allow
that task to submit an SQE that then assumes the ring mm and creds if
it needs to go async.
Cc: stable@vger.kernel.org
Suggested-by: Stefan Metzmacher <metze@samba.org>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The driver was issuing synchronous uninterruptible control requests
without using a timeout. This could lead to the driver hanging on probe
due to a malfunctioning (or malicious) device until the device is
physically disconnected. While sleeping in probe the driver prevents
other devices connected to the same hub from being added to (or removed
from) the bus.
The USB upper limit of five seconds per request should be more than
enough.
Fixes: 99f83c9c9ac9 ("[PATCH] USB: add driver for Keyspan Digital Remote")
Signed-off-by: Johan Hovold <johan@kernel.org>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable <stable@vger.kernel.org> # 2.6.13
Link: https://lore.kernel.org/r/20200113171715.30621-1-johan@kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
We need the of_match table if we want to use the compatible string in
the pmic's child node and get the onkey driver loaded automatically.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The F54 Report Data is apparently read through a fifo and for
the smbus protocol that means that between reading a block of 32
bytes the rmiaddr shouldn't be incremented. However, changing
that causes other non-fifo reads to fail and so that change was
reverted.
This patch changes just the F54 function and it now reads 32 bytes
at a time from the fifo, using the F54_FIFO_OFFSET to update the
start address that is used when reading from the fifo.
This has only been tested with smbus, not with i2c or spi. But I
suspect that the same is needed there since I think similar
problems will occur there when reading more than 256 bytes.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Tested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Link: https://lore.kernel.org/r/20200115124819.3191024-3-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This reverts commit a284e11c371e446371675668d8c8120a27227339.
This causes problems (drifting cursor) with at least the F11 function that
reads more than 32 bytes.
The real issue is in the F54 driver, and so this should be fixed there, and
not in rmi_smbus.c.
So first revert this bad commit, then fix the real problem in F54 in another
patch.
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Reported-by: Timo Kaufmann <timokau@zoho.com>
Fixes: a284e11c371e ("Input: synaptics-rmi4 - don't increment rmiaddr for SMBus transfers")
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/20200115124819.3191024-2-hverkuil-cisco@xs4all.nl
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
kernel/bpf/syscall.c: In function generic_map_lookup_batch:
kernel/bpf/syscall.c:1339:7: warning: variable first_key set but not used [-Wunused-but-set-variable]
It is never used, so remove it.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Brian Vazquez <brianvv@google.com>
Link: https://lore.kernel.org/bpf/20200116145300.59056-1-yuehaibing@huawei.com
|
|
Implement the H_SVM_INIT_ABORT hcall which the Ultravisor can use to
abort an SVM after it has issued the H_SVM_INIT_START and before the
H_SVM_INIT_DONE hcalls. This hcall could be used when Ultravisor
encounters security violations or other errors when starting an SVM.
Note that this hcall is different from UV_SVM_TERMINATE ucall which
is used by HV to terminate/cleanup an VM that has becore secure.
The H_SVM_INIT_ABORT basically undoes operations that were done
since the H_SVM_INIT_START hcall - i.e page-out all the VM pages back
to normal memory, and terminate the SVM.
(If we do not bring the pages back to normal memory, the text/data
of the VM would be stuck in secure memory and since the SVM did not
go secure, its MSR_S bit will be clear and the VM wont be able to
access its pages even to do a clean exit).
Based on patches and discussion with Paul Mackerras, Ram Pai and
Bharata Rao.
Signed-off-by: Ram Pai <linuxram@linux.ibm.com>
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Bharata B Rao <bharata@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Add 'skip_page_out' parameter to kvmppc_uvmem_drop_pages() so the
callers can specify whetheter or not to skip paging out pages. This
will be needed in a follow-on patch that implements H_SVM_INIT_ABORT
hcall.
Signed-off-by: Sukadev Bhattiprolu <sukadev@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Given that in kvm_create_vm() there is:
kvm->mm = current->mm;
And that on every kvm_*_ioctl we have:
if (kvm->mm != current->mm)
return -EIO;
I see no reason to keep using current->mm instead of kvm->mm.
By doing so, we would reduce the use of 'global' variables on code, relying
more in the contents of kvm struct.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Given that in kvm_create_vm() there is:
kvm->mm = current->mm;
And that on every kvm_*_ioctl we have:
if (kvm->mm != current->mm)
return -EIO;
I see no reason to keep using current->mm instead of kvm->mm.
By doing so, we would reduce the use of 'global' variables on code, relying
more in the contents of kvm struct.
Signed-off-by: Leonardo Bras <leonardo@linux.ibm.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:6: warning: variable ra set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:10: warning: variable rs set but not used [-Wunused-but-set-variable]
arch/powerpc/kvm/emulate_loadstore.c: In function kvmppc_emulate_loadstore:
arch/powerpc/kvm/emulate_loadstore.c:87:14: warning: variable rt set but not used [-Wunused-but-set-variable]
They are not used since commit 2b33cb585f94 ("KVM: PPC: Reimplement
LOAD_FP/STORE_FP instruction mmio emulation with analyse_instr() input")
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Paul Mackerras <paulus@ozlabs.org>
|
|
Toke Høiland-Jørgensen says:
====================
Since commit 96360004b862 ("xdp: Make devmap flush_list common for all map
instances"), devmap flushing is a global operation instead of tied to a
particular map. This means that with a bit of refactoring, we can finally fix
the performance delta between the bpf_redirect_map() and bpf_redirect() helper
functions, by introducing bulking for the latter as well.
This series makes this change by moving the data structure used for the bulking
into struct net_device itself, so we can access it even when there is not
devmap. Once this is done, moving the bpf_redirect() helper to use the bulking
mechanism becomes quite trivial, and brings bpf_redirect() up to the same as
bpf_redirect_map():
Before: After:
1 CPU:
bpf_redirect_map: 8.4 Mpps 8.4 Mpps (no change)
bpf_redirect: 5.0 Mpps 8.4 Mpps (+68%)
2 CPUs:
bpf_redirect_map: 15.9 Mpps 16.1 Mpps (+1% or ~no change)
bpf_redirect: 9.5 Mpps 15.9 Mpps (+67%)
After this patch series, the only semantics different between the two variants
of the bpf() helper (apart from the absence of a map argument, obviously) is
that the _map() variant will return an error if passed an invalid map index,
whereas the bpf_redirect() helper will succeed, but drop packets on
xdp_do_redirect(). This is because the helper has no reference to the calling
netdev, so unfortunately we can't do the ifindex lookup directly in the helper.
Changelog:
v3:
- Switch two more fields to avoid a list_head spanning two cache lines
- Include Jesper's tracepoint patch
- Also rename xdp_do_flush_map()
- Fix a few nits from Maciej
v2:
- Consolidate code paths and tracepoints for map and non-map redirect variants
(Björn)
- Add performance data for 2-CPU test (Jesper)
- Move fields to avoid shifting cache lines in struct net_device (Eric)
====================
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
Now that we don't have a reference to a devmap when flushing the device
bulk queue, let's change the the devmap_xmit tracepoint to remote the
map_id and map_index fields entirely. Rearrange the fields so 'drops' and
'sent' stay in the same position in the tracepoint struct, to make it
possible for the xdp_monitor utility to read both the old and the new
format.
Signed-off-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/157918768613.1458396.9165902403373826572.stgit@toke.dk
|
|
Since the bulk queue used by XDP_REDIRECT now lives in struct net_device,
we can re-use the bulking for the non-map version of the bpf_redirect()
helper. This is a simple matter of having xdp_do_redirect_slow() queue the
frame on the bulk queue instead of sending it out with __bpf_tx_xdp().
Unfortunately we can't make the bpf_redirect() helper return an error if
the ifindex doesn't exit (as bpf_redirect_map() does), because we don't
have a reference to the network namespace of the ingress device at the time
the helper is called. So we have to leave it as-is and keep the device
lookup in xdp_do_redirect_slow().
Since this leaves less reason to have the non-map redirect code in a
separate function, so we get rid of the xdp_do_redirect_slow() function
entirely. This does lose us the tracepoint disambiguation, but fortunately
the xdp_redirect and xdp_redirect_map tracepoints use the same tracepoint
entry structures. This means both can contain a map index, so we can just
amend the tracepoint definitions so we always emit the xdp_redirect(_err)
tracepoints, but with the map ID only populated if a map is present. This
means we retire the xdp_redirect_map(_err) tracepoints entirely, but keep
the definitions around in case someone is still listening for them.
With this change, the performance of the xdp_redirect sample program goes
from 5Mpps to 8.4Mpps (a 68% increase).
Since the flush functions are no longer map-specific, rename the flush()
functions to drop _map from their names. One of the renamed functions is
the xdp_do_flush_map() callback used in all the xdp-enabled drivers. To
keep from having to update all drivers, use a #define to keep the old name
working, and only update the virtual drivers in this patch.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/157918768505.1458396.17518057312953572912.stgit@toke.dk
|
|
Commit 96360004b862 ("xdp: Make devmap flush_list common for all map
instances"), changed devmap flushing to be a global operation instead of a
per-map operation. However, the queue structure used for bulking was still
allocated as part of the containing map.
This patch moves the devmap bulk queue into struct net_device. The
motivation for this is reusing it for the non-map variant of XDP_REDIRECT,
which will be changed in a subsequent commit. To avoid other fields of
struct net_device moving to different cache lines, we also move a couple of
other members around.
We defer the actual allocation of the bulk queue structure until the
NETDEV_REGISTER notification devmap.c. This makes it possible to check for
ndo_xdp_xmit support before allocating the structure, which is not possible
at the time struct net_device is allocated. However, we keep the freeing in
free_netdev() to avoid adding another RCU callback on NETDEV_UNREGISTER.
Because of this change, we lose the reference back to the map that
originated the redirect, so change the tracepoint to always return 0 as the
map ID and index. Otherwise no functional change is intended with this
patch.
After this patch, the relevant part of struct net_device looks like this,
according to pahole:
/* --- cacheline 14 boundary (896 bytes) --- */
struct netdev_queue * _tx __attribute__((__aligned__(64))); /* 896 8 */
unsigned int num_tx_queues; /* 904 4 */
unsigned int real_num_tx_queues; /* 908 4 */
struct Qdisc * qdisc; /* 912 8 */
unsigned int tx_queue_len; /* 920 4 */
spinlock_t tx_global_lock; /* 924 4 */
struct xdp_dev_bulk_queue * xdp_bulkq; /* 928 8 */
struct xps_dev_maps * xps_cpus_map; /* 936 8 */
struct xps_dev_maps * xps_rxqs_map; /* 944 8 */
struct mini_Qdisc * miniq_egress; /* 952 8 */
/* --- cacheline 15 boundary (960 bytes) --- */
struct hlist_head qdisc_hash[16]; /* 960 128 */
/* --- cacheline 17 boundary (1088 bytes) --- */
struct timer_list watchdog_timer; /* 1088 40 */
/* XXX last struct has 4 bytes of padding */
int watchdog_timeo; /* 1128 4 */
/* XXX 4 bytes hole, try to pack */
struct list_head todo_list; /* 1136 16 */
/* --- cacheline 18 boundary (1152 bytes) --- */
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Acked-by: Björn Töpel <bjorn.topel@intel.com>
Acked-by: John Fastabend <john.fastabend@gmail.com>
Link: https://lore.kernel.org/bpf/157918768397.1458396.12673224324627072349.stgit@toke.dk
|
|
Revert bpf_helpers.h's change to include auto-generated bpf_helper_defs.h
through <> instead of "", which causes it to be searched in include path. This
can break existing applications that don't have their include path pointing
directly to where libbpf installs its headers.
There is ongoing work to make all (not just bpf_helper_defs.h) includes more
consistent across libbpf and its consumers, but this unbreaks user code as is
right now without any regressions. Selftests still behave sub-optimally
(taking bpf_helper_defs.h from libbpf's source directory, if it's present
there), which will be fixed in subsequent patches.
Fixes: 6910d7d3867a ("selftests/bpf: Ensure bpf_helper_defs.h are taken from selftests dir")
Reported-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Andrii Nakryiko <andriin@fb.com>
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
Link: https://lore.kernel.org/bpf/20200117004103.148068-1-andriin@fb.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"I've been sitting on these longer than I meant, so the patch count is
a bit higher than ideal for this part of the release. There's also
some reverts of double-applied patches that brings the diffstat up a
bit.
With that said, the biggest changes are:
- Revert of duplicate i2c device addition on two Aspeed (BMC)
Devicetrees.
- Move of two device nodes that got applied to the wrong part of the
tree on ASpeed G6.
- Regulator fix for Beaglebone X15 (adding 12/5V supplies)
- Use interrupts for keys on Amlogic SM1 to avoid missed polls
In addition to that, there is a collection of smaller DT fixes:
- Power supply assignment fixes for i.MX6
- Fix of interrupt line for magnetometer on i.MX8 Librem5 devkit
- Build fixlets (selects) for davinci/omap2+
- More interrupt number fixes for Stratix10, Amlogic SM1, etc.
- ... and more similar fixes across different platforms
And some non-DT stuff:
- optee fix to register multiple shared pages properly
- Clock calculation fixes for MMP3
- Clock fixes for OMAP as well"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (42 commits)
MAINTAINERS: Add myself as the co-maintainer for Actions Semi platforms
ARM: dts: imx7: Fix Toradex Colibri iMX7S 256MB NAND flash support
ARM: dts: imx6sll-evk: Remove incorrect power supply assignment
ARM: dts: imx6sl-evk: Remove incorrect power supply assignment
ARM: dts: imx6sx-sdb: Remove incorrect power supply assignment
ARM: dts: imx6qdl-sabresd: Remove incorrect power supply assignment
ARM: dts: imx6q-icore-mipi: Use 1.5 version of i.Core MX6DL
ARM: omap2plus: select RESET_CONTROLLER
ARM: davinci: select CONFIG_RESET_CONTROLLER
ARM: dts: aspeed: rainier: Fix fan fault and presence
ARM: dts: aspeed: rainier: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Remove duplicate flash nodes
ARM: dts: aspeed: tacoma: Remove duplicate i2c busses
ARM: dts: aspeed: tacoma: Fix fsi master node
ARM: dts: aspeed-g6: Fix FSI master location
ARM: dts: mmp3: Fix the TWSI ranges
clk: mmp2: Fix the order of timer mux parents
ARM: mmp: do not divide the clock rate
arm64: dts: rockchip: Fix IR on Beelink A1
optee: Fix multi page dynamic shm pool alloc
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"Second collection of clk fixes for the next release.
This one includes a fix for PM on TI SoCs with sysc devices and fixes
a bunch of clks that are stuck always enabled on Qualcomm SDM845 SoCs.
Allwinner SoCs get the usual set of fixes too, mostly correcting
drivers to have the right bits that match the hardware.
There's also a Samsung and Tegra fix in here to mark a clk critical
and avoid a double free.
And finally there's a fix for critical clks that silences a big
warning splat about trying to enable a clk that couldn't even be
prepared"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: ti: dra7-atl: Remove pm_runtime_irq_safe()
clk: qcom: gcc-sdm845: Add missing flag to votable GDSCs
clk: sunxi-ng: h6-r: Fix AR100/R_APB2 parent order
clk: sunxi-ng: h6-r: Simplify R_APB1 clock definition
clk: sunxi-ng: sun8i-r: Fix divider on APB0 clock
clk: Don't try to enable critical clocks if prepare failed
clk: tegra: Fix double-free in tegra_clk_init()
clk: samsung: exynos5420: Keep top G3D clocks enabled
clk: sunxi-ng: r40: Allow setting parent rate for external clock outputs
clk: sunxi-ng: v3s: Fix incorrect number of hw_clks.
|
|
Fixes coccicheck warning:
./drivers/power/supply/ipaq_micro_battery.c:188:2-3: Unneeded semicolon
./drivers/power/supply/ipaq_micro_battery.c:152:3-4: Unneeded semicolon
./drivers/power/supply/ipaq_micro_battery.c:171:2-3: Unneeded semicolon
Signed-off-by: Chen Zhou <chenzhou10@huawei.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
|
|
In case of error, the function edac_device_alloc_ctl_info() returns a
NULL pointer, not ERR_PTR(). Replace the IS_ERR() test in the return
value check with a NULL test.
Fixes: 91abaeaaff35 ("EDAC/sifive: Add EDAC platform driver for SiFive SoCs")
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Link: https://lkml.kernel.org/r/20200115150303.112627-1-weiyongjun1@huawei.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fix from Rafael Wysocki:
"Fix a coding mistake in the teo cpuidle governor causing data to be
written beyond the last array element (Ikjoon Jang)"
* tag 'pm-5.5-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
cpuidle: teo: Fix intervals[] array indexing bug
|
|
Since I've been doing the maintainership work for couple of cycles, we've
decided to add myself as the co-maintainer along with Andreas.
Link: https://lore.kernel.org/r/20200114084348.25659-2-manivannan.sadhasivam@linaro.org
Cc: "Andreas Färber" <afaerber@suse.de>
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Acked-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Increase the number of chains and priorities to support
the whole range available in tc.
We use unmanaged tables and ignore flow level to create more
tables than what we declared to fs_core steering, and we manage
the connections between the tables themselves.
To support that we need FW with ignore_flow_level capability.
Otherwise the old behaviour will be used, where we are limited
by the number of levels we declared (4 chains, 16 prios).
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
To support the entire chain and prio range (32bit + 16bit),
instead of a using a static array of chains/prios of limited size, create
them dynamically, and use a rhashtable to search for existing chains/prio
combinations.
This will be used in next patch to actually increase the number using
unamanged tables support and ignore flow level capability.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Before changing the chain from original chain to ft offload chain,
make sure user doesn't actually use chains.
While here, normalize the prio range to that which we support.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
FT chain is defined as the next chain after tc.
To prepare for next patches that will increase the number of tc
chains available at runtime, use a getter function to get this
value.
The define is still used in static fs_core allocation,
to calculate the number of chains. This static allocation
will be used if the relevant capabilities won't be available
to support dynamic chains.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Exclude the last n entries for an autogrouped flow table.
Reserving entries at the end of the FT will ensure that this FG will be
the last to be evaluated. This will be used in the next patch to create
a miss group enabling custom actions on FT miss.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If user sets ignore flow level flag on a rule, that rule can point to
a flow table of any level, including those with levels equal or less
than the level of the flow table it is added on.
This with unamanged tables will be used to create a FDB chain/prio
hierarchy much larger than currently supported level range.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, Most of the steering tree is statically declared ahead of time,
with steering prios instances allocated for each fdb chain to assign max
number of levels for each of them. This allows fs_core to manage the
connections and levels of the flow tables hierarcy to prevent loops, but
restricts us with the number of supported chains and priorities.
Introduce unmananged flow tables, allowing the user to manage the flow
table connections. A unamanged table is detached from the fs_core flow
table hierarcy, and is only connected back to the hierarchy by explicit
FTEs forward actions.
This will be used together with firmware that supports ignoring the flow
table levels to increase the number of supported chains and prios.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
This merge syncs with mlx5-next latest HW bits and layout updates for next
features, in addition one patch that improves
mlx5_create_auto_grouped_flow_table() API across all mlx5 users.
* 'mlx5-next' of git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux:
net/mlx5: Refactor mlx5_create_auto_grouped_flow_table
net/mlx5e: Add discard counters per priority
net/mlx5e: Expose FEC feilds and related capability bit
net/mlx5: Add mlx5_ifc definitions for connection tracking support
net/mlx5: Add copy header action struct layout
net/mlx5: Expose resource dump register mapping
net/mlx5: Add structures and defines for MIRC register
net/mlx5: Read MCAM register groups 1 and 2
net/mlx5: Add structures layout for new MCAM access reg groups
net/mlx5: Expose vDPA emulation device capabilities
net/mlx5: Add Virtio Emulation related device capabilities
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On alpha and s390x:
fs/ubifs/debug.h:158:11: warning: format ‘%lu’ expects argument of type ‘long unsigned int’, but argument 4 has type ‘ino_t {aka unsigned int}’ [-Wformat=]
...
fs/ubifs/orphan.c:132:3: note: in expansion of macro ‘dbg_gen’
dbg_gen("deleted twice ino %lu", orph->inum);
...
fs/ubifs/orphan.c:140:3: note: in expansion of macro ‘dbg_gen’
dbg_gen("delete later ino %lu", orph->inum);
__kernel_ino_t is "unsigned long" on most architectures, but not on
alpha and s390x, where it is "unsigned int". Hence when printing an
ino_t, it should always be cast to "unsigned long" first.
Fix this by re-adding the recently removed casts.
Fixes: 8009ce956c3d2802 ("ubifs: Don't leak orphans on memory during commit")
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Refactor mlx5_create_auto_grouped_flow_table() to use ft_attr param
which already carries the max_fte, prio and flags memebers, and is
used the same in similar mlx5_create_flow_table() function.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Shlomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently the property entry kunit tests are built if CONFIG_KUNIT=y.
This will cause warnings when merged with the kunit tree that now
supports tristate CONFIG_KUNIT. While the tests appear to compile
as a module, we get a warning about missing module license.
It's better to have a per-test suite CONFIG variable so that
we can do selective building of kunit-based suites, and can
also avoid merge issues like this.
Fixes: c032ace71c29 ("software node: add basic tests for property entries")
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Alan Maguire <alan.maguire@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
Upon resuming from hibernation, free pages may contain stale data from
the kernel that initiated the resume. This breaks the invariant
inflicted by init_on_free=1 that freed pages must be zeroed.
To deal with this problem, make clear_free_pages() also clear the free
pages when init_on_free is enabled.
Fixes: 6471384af2a6 ("mm: security: introduce init_on_alloc=1 and init_on_free=1 boot options")
Reported-by: Johannes Stezenbach <js@sig21.net>
Signed-off-by: Alexander Potapenko <glider@google.com>
Cc: 5.3+ <stable@vger.kernel.org> # 5.3+
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
In ubifs, concurrent execution of writepage and bulk read on the same file
may cause ABBA deadlock, for example (Reproduce method see Link):
Process A(Bulk-read starts from page4) Process B(write page4 back)
vfs_read wb_workfn or fsync
... ...
generic_file_buffered_read write_cache_pages
ubifs_readpage LOCK(page4)
ubifs_bulk_read ubifs_writepage
LOCK(ui->ui_mutex) ubifs_write_inode
ubifs_do_bulk_read LOCK(ui->ui_mutex)
find_or_create_page(alloc page4) ↑
LOCK(page4) <-- ABBA deadlock occurs!
In order to ensure the serialization execution of bulk read, we can't
remove the big lock 'ui->ui_mutex' in ubifs_bulk_read(). Instead, we
allow ubifs_do_bulk_read() to lock page failed by replacing
find_or_create_page(FGP_LOCK) with
pagecache_get_page(FGP_LOCK | FGP_NOWAIT).
Signed-off-by: Zhihao Cheng <chengzhihao1@huawei.com>
Suggested-by: zhangyi (F) <yi.zhang@huawei.com>
Cc: <Stable@vger.kernel.org>
Fixes: 4793e7c5e1c ("UBIFS: add bulk-read facility")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=206153
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
In create_default_filesystem() when we allocate the idx node we must use
the idx_node_size we calculated just one line before, not tmp, which
contains completely other data.
Fixes: c4de6d7e4319 ("ubifs: Refactor create_default_filesystem()")
Cc: stable@vger.kernel.org # v4.20+
Reported-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Tested-by: Naga Sureshkumar Relli <nagasure@xilinx.com>
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The allocated normal volumes saved in ubi->volumes are not freed
in the error paths in ubi_attach_mtd_dev() and its callees (e.g.
ubi_attach() and ubi_read_volume_table()).
These normal volumes should be freed through kill_volumes() and
vol_release(), but ubi_attach_mtd_dev() may fail before
calling uif_init(), and there will be memory leaks.
So adding a new helper ubi_free_all_volumes() to free the normal
and the internal volumes. And in order to prevent double-free
of volume, reset ubi->volumes[i] to NULL after freeing.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Else there may be oops when fastmap is enabled and init_volumes() fails.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Make the FS_IOC_GETFLAGS ioctl on ubifs return the FS_ENCRYPT_FL flag on
encrypted files, like ext4 and f2fs do.
Also make this flag be ignored by FS_IOC_SETFLAGS, like ext4 and f2fs
do, since it's a recognized flag but is not directly settable.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
UBIFS's implementation of FS_IOC_SETFLAGS fails to preserve existing
inode flags that aren't settable by FS_IOC_SETFLAGS, namely the encrypt
flag. This causes the encrypt flag to be unexpectedly cleared.
Fix it by preserving existing unsettable flags, like ext4 and f2fs do.
Test case with kvm-xfstests shell:
FSTYP=ubifs KEYCTL_PROG=keyctl
. fs/ubifs/config
. ~/xfstests/common/encrypt
dev=$(__blkdev_to_ubi_volume /dev/vdc)
ubiupdatevol -t $dev
mount $dev /mnt -t ubifs
k=$(_generate_session_encryption_key)
mkdir /mnt/edir
xfs_io -c "set_encpolicy $k" /mnt/edir
echo contents > /mnt/edir/file
chattr +i /mnt/edir/file
chattr -i /mnt/edir/file
With the bug, the following errors occur on the last command:
[ 18.081559] fscrypt (ubifs, inode 67): Inconsistent encryption context (parent directory: 65)
chattr: Operation not permitted while reading flags on /mnt/edir/file
Fixes: d475a507457b ("ubifs: Add skeleton for fscrypto")
Cc: <stable@vger.kernel.org> # v4.10+
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/ubi/wl.c: In function 'find_wl_entry':
drivers/mtd/ubi/wl.c:322:27: warning:
variable 'prev_e' set but not used [-Wunused-but-set-variable]
It's not used any more now, so remove it.
Fixes: f9c34bb52997 ("ubi: Fix producing anchor PEBs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb00840 ("ubi: Use bitmaps in Fastmap self-check code")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Add counters that count (per priority) the number of received
packets that dropped due to lack of buffers on a physical port. If
this counter is increasing, it implies that the adapter is
congested and cannot absorb the traffic coming from the network.
Signed-off-by: Aharon Landau <aharonl@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Introduce 50G per lane FEC modes capability bit and newly supported
fields in PPLM register which allow this configuration.
Signed-off-by: Aya Levin <ayal@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the required hardware definitions to mlx5_ifc:
ignore_flow_level, registers, copy_header, and fwd_and_modify cap.
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Oz Sholomo <ozsh@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add definition for copy header action, copy action is used
to copy header fields from source to destination.
Signed-off-by: Hamdan Igbaria <hamdani@mellanox.com>
Signed-off-by: Alex Vesker <valex@mellanox.com>
Reviewed-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
