| Age | Commit message (Collapse) | Author |
|---|
|
clang static analysis reports this problem
dfs_cache.c:591:2: warning: Argument to kfree() is a constant address
(18446744073709551614), which is not memory allocated by malloc()
kfree(vi);
^~~~~~~~~
In dfs_cache_del_vol() the volume info pointer 'vi' being freed
is the return of a call to find_vol(). The large constant address
is find_vol() returning an error.
Add an error check to dfs_cache_del_vol() similar to the one done
in dfs_cache_update_vol().
Fixes: 54be1f6c1c37 ("cifs: Add DFS cache routines")
Signed-off-by: Tom Rix <trix@redhat.com>
Reviewed-by: Nathan Chancellor <natechancellor@gmail.com>
CC: <stable@vger.kernel.org> # v5.0+
Signed-off-by: Steve French <stfrench@microsoft.com>
|
|
The call state may be changed at any time by the data-ready routine in
response to received packets, so if the call state is to be read and acted
upon several times in a function, READ_ONCE() must be used unless the call
state lock is held.
As it happens, we used READ_ONCE() to read the state a few lines above the
unmarked read in rxrpc_input_data(), so use that value rather than
re-reading it.
Fixes: a158bdd3247b ("rxrpc: Fix call timeouts")
Signed-off-by: Baptiste Lepers <baptiste.lepers@gmail.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Link: https://lore.kernel.org/r/161046715522.2450566.488819910256264150.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Clang static analysis reports the following:
net/rxrpc/key.c:657:11: warning: Assigned value is garbage or undefined
toksize = toksizes[tok++];
^ ~~~~~~~~~~~~~~~
rxrpc_read() contains two consecutive loops. The first loop calculates the
token sizes and stores the results in toksizes[] and the second one uses
the array. When there is an error in identifying the token in the first
loop, the token is skipped, no change is made to the toksizes[] array.
When the same error happens in the second loop, the token is not skipped.
This will cause the toksizes[] array to be out of step and will overrun
past the calculated sizes.
Fix this by making both loops log a message and return an error in this
case. This should only happen if a new token type is incompletely
implemented, so it should normally be impossible to trigger this.
Fixes: 9a059cd5ca7d ("rxrpc: Downgrade the BUG() for unsupported token type in rxrpc_read()")
Reported-by: Tom Rix <trix@redhat.com>
Signed-off-by: David Howells <dhowells@redhat.com>
Reviewed-by: Tom Rix <trix@redhat.com>
Link: https://lore.kernel.org/r/161046503122.2445787.16714129930607546635.stgit@warthog.procyon.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
The earlier commit to fix runtime PM in case i915 init fails,
introduces a possibility to hit a page fault.
snd_hdac_ext_bus_device_exit() is designed to be called from
dev.release(). Calling it outside device reference counting, is
not safe and may lead to calling the device_exit() function
twice. Additionally, as part of ext_bus_device_init(), the device
is also registered with snd_hdac_device_register(). Thus before
calling device_exit(), the device must be removed from device
hierarchy first.
Fix the issue by rolling back init actions by calling
hdac_device_unregister() and then releasing device with put_device().
This matches with existing code in hdac-ext module.
To complete the fix, add handling for the case where
hda_codec_load_module() returns -ENODEV, and clean up the hdac_ext
resources also in this case.
In future work, hdac-ext interface should be extended to allow clients
more flexibility to handle the life-cycle of individual devices, beyond
just the current snd_hdac_ext_bus_device_remove(), which removes all
devices.
BugLink: https://github.com/thesofproject/linux/issues/2646
Reported-by: Jaroslav Kysela <perex@perex.cz>
Fixes: 6c63c954e1c5 ("ASoC: SOF: fix a runtime pm issue in SOF when HDMI codec doesn't work")
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Rander Wang <rander.wang@intel.com>
Reviewed-by: Libin Yang <libin.yang@intel.com>
Reviewed-by: Bard Liao <bard.liao@intel.com>
Link: https://lore.kernel.org/r/20210113150715.3992635-1-kai.vehmanen@linux.intel.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
When lazytime is enabled and an inode is being written due to its
in-memory updated timestamps having expired, either due to a sync() or
syncfs() system call or due to dirtytime_expire_interval having elapsed,
the VFS needs to inform the filesystem so that the filesystem can copy
the inode's timestamps out to the on-disk data structures.
This is done by __writeback_single_inode() calling
mark_inode_dirty_sync(), which then calls ->dirty_inode(I_DIRTY_SYNC).
However, this occurs after __writeback_single_inode() has already
cleared the dirty flags from ->i_state. This causes two bugs:
- mark_inode_dirty_sync() redirties the inode, causing it to remain
dirty. This wastefully causes the inode to be written twice. But
more importantly, it breaks cases where sync_filesystem() is expected
to clean dirty inodes. This includes the FS_IOC_REMOVE_ENCRYPTION_KEY
ioctl (as reported at
https://lore.kernel.org/r/20200306004555.GB225345@gmail.com), as well
as possibly filesystem freezing (freeze_super()).
- Since ->i_state doesn't contain I_DIRTY_TIME when ->dirty_inode() is
called from __writeback_single_inode() for lazytime expiration,
xfs_fs_dirty_inode() ignores the notification. (XFS only cares about
lazytime expirations, and it assumes that i_state will contain
I_DIRTY_TIME during those.) Therefore, lazy timestamps aren't
persisted by sync(), syncfs(), or dirtytime_expire_interval on XFS.
Fix this by moving the call to mark_inode_dirty_sync() to earlier in
__writeback_single_inode(), before the dirty flags are cleared from
i_state. This makes filesystems be properly notified of the timestamp
expiration, and it avoids incorrectly redirtying the inode.
This fixes xfstest generic/580 (which tests
FS_IOC_REMOVE_ENCRYPTION_KEY) when run on ext4 or f2fs with lazytime
enabled. It also fixes the new lazytime xfstest I've proposed, which
reproduces the above-mentioned XFS bug
(https://lore.kernel.org/r/20210105005818.92978-1-ebiggers@kernel.org).
Alternatively, we could call ->dirty_inode(I_DIRTY_SYNC) directly. But
due to the introduction of I_SYNC_QUEUED, mark_inode_dirty_sync() is the
right thing to do because mark_inode_dirty_sync() now knows not to move
the inode to a writeback list if it is currently queued for sync.
Fixes: 0ae45f63d4ef ("vfs: add support for a lazytime mount option")
Cc: stable@vger.kernel.org
Depends-on: 5afced3bf281 ("writeback: Avoid skipping inode writeback")
Link: https://lore.kernel.org/r/20210112190253.64307-2-ebiggers@kernel.org
Suggested-by: Jan Kara <jack@suse.cz>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
|
|
device tree users
Module alias "spi:93xx46" is used by non device tree users like
drivers/misc/eeprom/digsy_mtc_eeprom.c and removing it will
break support for them.
Fix this by adding back the module alias "spi:93xx46".
Fixes: 13613a2246bf ("misc: eeprom_93xx46: Fix module alias to enable module autoprobe")
Signed-off-by: Aswath Govindraju <a-govindraju@ti.com>
Link: https://lore.kernel.org/r/20210113051253.15061-1-a-govindraju@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add HD Audio PCI ID and HDMI codec vendor ID for Intel AlderLake-P.
Signed-off-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Reviewed-by: Ranjani Sridharan <ranjani.sridharan@linux.intel.com>
Reviewed-by: Pierre-Louis Bossart <pierre-louis.bossart@linux.intel.com>
Reviewed-by: Guennadi Liakhovetski <guennadi.liakhovetski@linux.intel.com>
Link: https://lore.kernel.org/r/20210113155629.4097057-1-kai.vehmanen@linux.intel.com
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
WARNING: CPU: 0 PID: 8494 at fs/io_uring.c:8717
io_ring_ctx_wait_and_kill+0x4f2/0x600 fs/io_uring.c:8717
Call Trace:
io_uring_release+0x3e/0x50 fs/io_uring.c:8759
__fput+0x283/0x920 fs/file_table.c:280
task_work_run+0xdd/0x190 kernel/task_work.c:140
tracehook_notify_resume include/linux/tracehook.h:189 [inline]
exit_to_user_mode_loop kernel/entry/common.c:174 [inline]
exit_to_user_mode_prepare+0x249/0x250 kernel/entry/common.c:201
__syscall_exit_to_user_mode_work kernel/entry/common.c:291 [inline]
syscall_exit_to_user_mode+0x19/0x50 kernel/entry/common.c:302
entry_SYSCALL_64_after_hwframe+0x44/0xa9
failed io_uring_install_fd() is a special case, we don't do
io_ring_ctx_wait_and_kill() directly but defer it to fput, though still
need to io_disable_sqo_submit() before.
note: it doesn't fix any real problem, just a warning. That's because
sqring won't be available to the userspace in this case and so SQPOLL
won't submit anything.
Reported-by: syzbot+9c9c35374c0ecac06516@syzkaller.appspotmail.com
Fixes: d9d05217cb69 ("io_uring: stop SQPOLL submit on creator's death")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
general protection fault, probably for non-canonical address
0xdffffc0000000022: 0000 [#1] KASAN: null-ptr-deref
in range [0x0000000000000110-0x0000000000000117]
RIP: 0010:io_ring_set_wakeup_flag fs/io_uring.c:6929 [inline]
RIP: 0010:io_disable_sqo_submit+0xdb/0x130 fs/io_uring.c:8891
Call Trace:
io_uring_create fs/io_uring.c:9711 [inline]
io_uring_setup+0x12b1/0x38e0 fs/io_uring.c:9739
do_syscall_64+0x2d/0x70 arch/x86/entry/common.c:46
entry_SYSCALL_64_after_hwframe+0x44/0xa9
io_disable_sqo_submit() might be called before user rings were
allocated, don't do io_ring_set_wakeup_flag() in those cases.
Reported-by: syzbot+ab412638aeb652ded540@syzkaller.appspotmail.com
Fixes: d9d05217cb69 ("io_uring: stop SQPOLL submit on creator's death")
Signed-off-by: Pavel Begunkov <asml.silence@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
System takes a very long time to suspend after commit 215a22ed31a1
("ALSA: hda: Refactor codec PM to use direct-complete optimization"):
[ 90.065964] PM: suspend entry (s2idle)
[ 90.067337] Filesystems sync: 0.001 seconds
[ 90.185758] Freezing user space processes ... (elapsed 0.002 seconds) done.
[ 90.188713] OOM killer disabled.
[ 90.188714] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 90.190024] printk: Suspending console(s) (use no_console_suspend to debug)
[ 90.904912] intel_pch_thermal 0000:00:12.0: CPU-PCH is cool [49C], continue to suspend
[ 321.262505] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 328.426919] snd_hda_codec_realtek ehdaudio0D0: Unable to sync register 0x2b8000. -5
[ 329.490933] ACPI: EC: interrupt blocked
That commit keeps the codec suspended during the system suspend. However,
mute/micmute LED will clear codec's direct-complete flag by
dpm_clear_superiors_direct_complete().
This doesn't play well with SOF driver. When its runtime resume is
called for system suspend, hda_codec_jack_check() schedules
jackpoll_work which uses snd_hdac_is_power_on() to check whether codec
is suspended. Because the direct-complete path isn't taken,
pm_runtime_disable() isn't called so snd_hdac_is_power_on() returns
false and jackpoll continues to run, and snd_hda_power_up_pm() cannot
power up an already suspended codec in multiple attempts, causes the
long delay on system suspend:
if (dev->power.direct_complete) {
if (pm_runtime_status_suspended(dev)) {
pm_runtime_disable(dev);
if (pm_runtime_status_suspended(dev)) {
pm_dev_dbg(dev, state, "direct-complete ");
goto Complete;
}
pm_runtime_enable(dev);
}
dev->power.direct_complete = false;
}
When direct-complete path is taken, snd_hdac_is_power_on() returns true
and hda_jackpoll_work() is skipped by accident. So this is still not
correct.
If we were to use snd_hdac_is_power_on() in system PM path,
pm_runtime_status_suspended() should be used instead of
pm_runtime_suspended(), otherwise pm_runtime_{enable,disable}() may
change the outcome of snd_hdac_is_power_on().
Because devices suspend in reverse order (i.e. child first), it doesn't
make much sense to resume an already suspended codec from audio
controller. So avoid the issue by making sure jackpoll isn't used in
system PM process.
Fixes: 215a22ed31a1 ("ALSA: hda: Refactor codec PM to use direct-complete optimization")
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Kai Vehmanen <kai.vehmanen@linux.intel.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-3-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Modify hda_codec_jack_wake_enable() to also support disable WAKEEN.
In addition, this patch also moves the WAKEEN disablement call out of
hda_codec_jack_check() into hda_codec_jack_wake_enable().
This is a preparation for next patch.
No functional change intended.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-2-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Instead of queueing jackpoll_work, runtime resume the codec to let it
use different jack detection methods based on jackpoll_interval.
This partially matches SOF driver's behavior with commit a6e7d0a4bdb0
("ALSA: hda: fix jack detection with Realtek codecs when in D3"), the
difference is SOF unconditionally resumes the codec.
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Link: https://lore.kernel.org/r/20210112181128.1229827-1-kai.heng.feng@canonical.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Only the IPI-related functions in the smp_ops should be conditional
on the vector callback being available. The rest should still happen:
• xen_hvm_smp_prepare_boot_cpu()
This function does two things, both of which should still happen if
there is no vector callback support.
The call to xen_vcpu_setup() for vCPU0 should still happen as it just
sets up the vcpu_info for CPU0. That does happen for the secondary
vCPUs too, from xen_cpu_up_prepare_hvm().
The second thing it does is call xen_init_spinlocks(), which perhaps
counter-intuitively should *also* still be happening in the case
without vector callbacks, so that it can clear its local xen_pvspin
flag and disable the virt_spin_lock_key accordingly.
Checking xen_have_vector_callback in xen_init_spinlocks() itself
would affect PV guests, so set the global nopvspin flag in
xen_hvm_smp_init() instead, when vector callbacks aren't available.
• xen_hvm_smp_prepare_cpus()
This does some IPI-related setup by calling xen_smp_intr_init() and
xen_init_lock_cpu(), which can be made conditional. And it sets the
xen_vcpu_id to XEN_VCPU_ID_INVALID for all possible CPUS, which does
need to happen.
• xen_smp_cpus_done()
This offlines any vCPUs which doesn't fit in the global shared_info
page, if separate vcpu_info placement isn't available. That part also
needs to happen regardless of vector callback support.
• xen_hvm_cpu_die()
This doesn't actually do anything other than commin_cpu_die() right
right now in the !vector_callback case; all three teardown functions
it calls should be no-ops. But to guard against future regressions
it's useful to call it anyway, and for it to explicitly check for
xen_have_vector_callback before calling those additional functions.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-6-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
In the case where xen_have_vector_callback is false, we still register
the IPI vectors in xen_smp_intr_init() for the secondary CPUs even
though they aren't going to be used. Stop doing that.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-5-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
It's useful to be able to test non-vector event channel delivery, to make
sure Linux will work properly on older Xen which doesn't have it.
It's also useful for those working on Xen and Xen-compatible hypervisors,
because there are guest kernels still in active use which use PCI INTX
even when vector delivery is available.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-4-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
With INTX or GSI delivery, Xen uses the event channel structures of CPU0.
If the interrupt gets handled by Linux on a different CPU, then no events
are seen as pending. Rather than introducing locking to allow other CPUs
to process CPU0's events, just ensure that the PCI interrupts happens
only on CPU0.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210106153958.584169-3-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
For a while, event channel notification via the PCI platform device
has been broken, because we attempt to communicate with xenstore before
we even have notifications working, with the xs_reset_watches() call
in xs_init().
We tend to get away with this on Xen versions below 4.0 because we avoid
calling xs_reset_watches() anyway, because xenstore might not cope with
reading a non-existent key. And newer Xen *does* have the vector
callback support, so we rarely fall back to INTX/GSI delivery.
To fix it, clean up a bit of the mess of xs_init() and xenbus_probe()
startup. Call xs_init() directly from xenbus_init() only in the !XS_HVM
case, deferring it to be called from xenbus_probe() in the XS_HVM case
instead.
Then fix up the invocation of xenbus_probe() to happen either from its
device_initcall if the callback is available early enough, or when the
callback is finally set up. This means that the hack of calling
xenbus_probe() from a workqueue after the first interrupt, or directly
from the PCI platform device setup, is no longer needed.
Signed-off-by: David Woodhouse <dwmw@amazon.co.uk>
Reviewed-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Link: https://lore.kernel.org/r/20210113132606.422794-2-dwmw2@infradead.org
Signed-off-by: Juergen Gross <jgross@suse.com>
|
|
USBPHYC has a register per phy to control and monitor the debug interface
of the HS PHY through a digital debug access.
With this register, it is possible to know if PLL Lock input to phy is
high. That means the PLL is ready for HS operation.
Instead of using an hard-coded delay after PLL enable and PLL disable, use
this bit to ensure good operating of the HS PHY.
Also use an atomic counter (n_pll_cons) to count the actual number of PLL
consumers and get rid of stm32_usbphyc_has_one_phy_active.
The boolean active in the usbphyc_phy structure is kept, because we need to
know in remove if a phy_exit is required to properly disable the PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-7-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
To ensure a good balancing of regulators, and allow PLL disabling when the
driver is removed, call stm32_usbphyc_phy_exit on each ports to set phys
inactive and disable PLL.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-6-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
To ensure a good balancing of regulators, force PLL disable either by
reset or by clearing the PLLEN bit.
If waiting the powerdown pulse delay isn't enough, return -EPROBE_DEFER
instead of polling the PLLEN bit, which will be low at the next probe.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-5-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Due to async_schedule_domain call in regulator_bulk_enable,
scheduling while atomic bug can raise if regulator_bulk_enable is called
under atomic context.
To avoid this issue, this patch replaces all regulator_bulk* by regulator_
per regulators.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-4-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PLL block requires to be powered with 1v1 and 1v8 supplies to catch
ENABLE signal.
Currently, supplies are managed through phy_ops .power_on/off, and PLL
activation/deactivation is managed through phy_ops .init/exit.
The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB
drivers dependent.
To ensure a good behavior of the PLL, supplies have to be managed at PLL
activation/deactivation. That means the supplies need to be put in usbphyc
node and not in phy children nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Link: https://lore.kernel.org/r/20210105090525.23164-3-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
PLL block requires to be powered with 1v1 and 1v8 supplies to catch ENABLE
signal.
Currently, supplies are managed through phy_ops .power_on/off, and PLL
activation/deactivation is managed through phy_ops .init/exit.
The sequence of phy_ops .power_on/.phy_init, .power_off/.exit is USB
drivers dependent.
To ensure a good behavior of the PLL, supplies have to be managed at PLL
activation/deactivation. That means the supplies need to be put in usbphyc
parent node and not in phy children nodes.
Signed-off-by: Amelie Delaunay <amelie.delaunay@foss.st.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210105090525.23164-2-amelie.delaunay@foss.st.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
With UBSAN enabled and building with clang, there are occasionally
warnings like
WARNING: modpost: vmlinux.o(.text+0xc533ec): Section mismatch in reference from the function arch_atomic64_or() to the variable .init.data:numa_nodes_parsed
The function arch_atomic64_or() references
the variable __initdata numa_nodes_parsed.
This is often because arch_atomic64_or lacks a __initdata
annotation or the annotation of numa_nodes_parsed is wrong.
for functions that end up not being inlined as intended but operating
on __initdata variables. Mark these as __always_inline, along with
the corresponding asm-generic wrappers.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210108092024.4034860-1-arnd@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
S_FRAME_SIZE is the size of the pt_regs structure, no longer the size of
the kernel stack frame, the name is misleading. In keeping with arm32,
rename S_FRAME_SIZE to PT_REGS_SIZE.
Signed-off-by: Jianlin Lv <Jianlin.Lv@arm.com>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Link: https://lore.kernel.org/r/20210112015813.2340969-1-Jianlin.Lv@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
This reverts commit 367c820ef08082e68df8a3bc12e62393af21e4b5.
lockup_detector_init() makes heavy use of per-cpu variables and must be
called with preemption disabled. Usually, it's handled early during boot
in kernel_init_freeable(), before SMP has been initialised.
Since we do not know whether or not our PMU interrupt can be signalled
as an NMI until considerably later in the boot process, the Arm PMU
driver attempts to re-initialise the lockup detector off the back of a
device_initcall(). Unfortunately, this is called from preemptible
context and results in the following splat:
| BUG: using smp_processor_id() in preemptible [00000000] code: swapper/0/1
| caller is debug_smp_processor_id+0x20/0x2c
| CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.10.0+ #276
| Hardware name: linux,dummy-virt (DT)
| Call trace:
| dump_backtrace+0x0/0x3c0
| show_stack+0x20/0x6c
| dump_stack+0x2f0/0x42c
| check_preemption_disabled+0x1cc/0x1dc
| debug_smp_processor_id+0x20/0x2c
| hardlockup_detector_event_create+0x34/0x18c
| hardlockup_detector_perf_init+0x2c/0x134
| watchdog_nmi_probe+0x18/0x24
| lockup_detector_init+0x44/0xa8
| armv8_pmu_driver_init+0x54/0x78
| do_one_initcall+0x184/0x43c
| kernel_init_freeable+0x368/0x380
| kernel_init+0x1c/0x1cc
| ret_from_fork+0x10/0x30
Rather than bodge this with raw_smp_processor_id() or randomly disabling
preemption, simply revert the culprit for now until we figure out how to
do this properly.
Reported-by: Lecopzer Chen <lecopzer.chen@mediatek.com>
Signed-off-by: Will Deacon <will@kernel.org>
Acked-by: Mark Rutland <mark.rutland@arm.com>
Cc: Sumit Garg <sumit.garg@linaro.org>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Link: https://lore.kernel.org/r/20201221162249.3119-1-lecopzer.chen@mediatek.com
Link: https://lore.kernel.org/r/20210112221855.10666-1-will@kernel.org
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
One of the users can be built modular:
ERROR: modpost: "irq_check_status_bit" [drivers/perf/arm_spe_pmu.ko] undefined!
Fixes: fdd029630434 ("genirq: Move status flag checks to core")
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20201227192049.GA195845@roeck-us.net
|
|
Changeset ba2bf1f090eb ("dt-bindings: phy: Add Cadence Sierra PHY bindings in YAML format")
renamed: Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
to: Documentation/devicetree/bindings/phy/phy-cadence-sierra.yaml.
Update its cross-reference accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/3550b08d4e8312e7d4a247a3515a93a5f0fd04c5.1610535350.git.mchehab+huawei@kernel.org
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
BCM4908 seems to have slightly different registers but works when
programmed just like the STB one.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210106205838.10964-3-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
BCM4908 uses the same PHY and may require just a slightly different
programming.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210106205838.10964-2-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Changes that require mentioning:
1. interrupt-names
Name "wakeup" was changed to the "wake". It matches example and what
Linux driver looks for in the first place
2. brcm,ipp and brcm,ioc
Both were described as booleans with 0 / 1 values. In examples they
were integers and Linux checks for int as well. Both got uint32.
3. Added minimal description
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20210106205838.10964-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix the following sparse warning:
drivers/phy/mediatek/phy-mtk-mipi-dsi.c:237:24: warning: symbol 'mtk_mipi_tx_driver' was not declared. Should it be static?
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Link: https://lore.kernel.org/r/1610415484-92497-1-git-send-email-zou_wei@huawei.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Commit 156708adf2d9 ("SUNRPC: Move the svc_xdr_recvfrom()
tracepoint") tried to capture the correct XID in the trace record,
but this line in svc_recv:
rqstp->rq_xid = svc_getu32(&rqstp->rq_arg.head[0]);
alters the size of rq_arg.head[0].iov_len. The tracepoint records
the correct XID but an incorrect value for the length of the
xdr_buf's head.
To keep the trace callsites simple, I've created two trace classes.
One assumes the xdr_buf contains a full RPC message, and the XID
can be extracted from it. The other assumes the contents of the
xdr_buf are arbitrary, and the xid will be provided by the caller.
Currently there is only one user of each class, but I expect we will
need a few more tracepoints using each class as time goes on.
Signed-off-by: Chuck Lever <chuck.lever@oracle.com>
|
|
Commit 65dc2e725286 ("usb: dwc2: Update Core Reset programming flow.")
revealed that the phy isn't ready immediately after enabling it's
clocks. The dwc2_check_core_version() fails and the dwc2 usb driver
errors out.
Add a short delay to let the phy get up and running. There isn't any
documentation how much time is required, the value was chosen based on
tests.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Hauke Mehrtens <hauke@hauke-m.de>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: <stable@vger.kernel.org> # v5.7+
Link: https://lore.kernel.org/r/20210107224901.2102479-1-dev@kresin.me
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert MIPI DSI PHY binding to YAML schema mediatek,dsi-phy.yaml
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201225075258.33352-7-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert HDMI PHY binding to YAML schema mediatek,hdmi-phy.yaml
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Chun-Kuang Hu <chunkuang.hu@kernel.org>
Cc: Philipp Zabel <p.zabel@pengutronix.de>
Link: https://lore.kernel.org/r/20201225075258.33352-6-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert phy-mtk-ufs.txt to YAML schema mediatek,ufs-phy.yaml
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Stanley Chu <stanley.chu@mediatek.com>
Cc: Stanley Chu <stanley.chu@mediatek.com>
Link: https://lore.kernel.org/r/20201225075258.33352-5-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert phy-mtk-tphy.txt to YAML schema mediatek,tphy.yaml
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201225075258.33352-4-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Convert phy-mtk-xsphy.txt to YAML schema mediatek,xsphy.yaml
Signed-off-by: Chunfeng Yun <chunfeng.yun@mediatek.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201225075258.33352-3-chunfeng.yun@mediatek.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
All EL0 returns go via ret_to_user(), which masks IRQs and notifies
lockdep and tracing before calling into do_notify_resume(). Therefore,
there's no need for do_notify_resume() to call trace_hardirqs_off(), and
the comment is stale. The call is simply redundant.
In ret_to_user() we call exit_to_user_mode(), which notifies lockdep and
tracing the IRQs will be enabled in userspace, so there's no need for
el0_svc_common() to call trace_hardirqs_on() before returning. Further,
at the start of ret_to_user() we call trace_hardirqs_off(), so not only
is this redundant, but it is immediately undone.
In addition to being redundant, the trace_hardirqs_on() in
el0_svc_common() leaves lockdep inconsistent with the hardware state,
and is liable to cause issues for any C code or instrumentation
between this and the call to trace_hardirqs_off() which undoes it in
ret_to_user().
This patch removes the redundant tracing calls and associated stale
comments.
Fixes: 23529049c684 ("arm64: entry: fix non-NMI user<->kernel transitions")
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Acked-by: Will Deacon <will@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Will Deacon <will@kernel.org>
Link: https://lore.kernel.org/r/20210107145310.44616-1-mark.rutland@arm.com
Signed-off-by: Catalin Marinas <catalin.marinas@arm.com>
|
|
Remove the useless field .version from the private structure, which is
set but never read.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@wanyeetech.com>
Link: https://lore.kernel.org/r/20201223124505.40792-1-paul@crapouillou.net
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This error path should return -EINVAL, but currently it returns
success.
Fixes: d09945eacad0 ("phy: cadence-torrent: Check total lane count for all subnodes is within limit")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Link: https://lore.kernel.org/r/X9s7Wxq+b6ls0q7o@mwanda
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
This is slightly cleaner solution that assures noone assings a wrong
function to the pointer.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201216143305.12179-2-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
1. Use of_device_get_match_data() helper to simplify the code
2. Check for NULL as a good practice
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20201216143305.12179-1-zajec5@gmail.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Update the implementation add "rockchip," vendor prefix for the
optional dts properties. Prefix referred from vendor-prefixes.yaml.
Follow up with
commit 8b5c2b45b8f0a ("phy: rockchip: set pulldown for strobe line in dts")
commit a8cef928276bb ("phy: rockchip-emmc: output tap delay dt property")
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Link: https://lore.kernel.org/r/20201215014409.905-3-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Update the documentation and add the vendor prefix to the optional
properties referred in vendor-prefixes.yaml.
Follow up with
commit 8b5c2b45b8f0a ("phy: rockchip: set pulldown for strobe line in dts")
commit a8cef928276bb ("phy: rockchip-emmc: output tap delay dt property")
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20201215014409.905-2-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Fix the following warning:
drivers/phy/motorola/phy-cpcap-usb.c:146:31-36: WARNING: conversion to
bool not needed here.
Signed-off-by: Tian Tao <tiantao6@hisilicon.com>
Link: https://lore.kernel.org/r/1607598716-16108-1-git-send-email-tiantao6@hisilicon.com
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
rockchip_emmc_phy_init() return variable is not set with the error value
if clk_get() failed. 'emmcclk' is optional, thus use clk_get_optional()
and if the return value != NULL make error processing and set the
return code accordingly.
Fixes: 52c0624a10cce phy: rockchip-emmc: Set phyctrl_frqsel based on card clock
Signed-off-by: Chris Ruehl <chris.ruehl@gtsys.com.hk>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20201210080454.17379-1-chris.ruehl@gtsys.com.hk
Signed-off-by: Vinod Koul <vkoul@kernel.org>
|
|
Changeset 81437cc3b0d9 ("Merge series "dt-bindings: stm32: convert audio dfsdm to json-schema" from Olivier Moysan <olivier.moysan@st.com>:")
removed bindings/sound/st,stm32-adfsdm.txt, as stm32-* audio
bindings are now under: bindings/iio/adc/st,stm32-*.yaml.
Update cross-references to them accordingly.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
Link: https://lore.kernel.org/r/03950bbd5cf7bac10eaaff3725e283d3ec2538c5.1610536535.git.mchehab+huawei@kernel.org
Signed-off-by: Mark Brown <broonie@kernel.org>
|
