| Age | Commit message (Collapse) | Author |
|---|
|
Add an SPDX identifier and remove any specific statements.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The error code read from the queue status register is only 6 bits wide,
but we need to verify its value is within range before indexing the error
messages.
Fixes: 81422badb3907 ("crypto: ccp - Make syslog errors human-readable")
Cc: <stable@vger.kernel.org>
Reported-by: Cfir Cohen <cfir@google.com>
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Tidy up the formatting/grammar in crypto_engine.rst. Use bulleted lists
where appropriate.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Fill in missing parameter descriptions for the compression algorithm,
then pick them up to document for the compression_alg structure.
Signed-off-by: Gary R Hook <gary.hook@amd.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This implements 5-way interleaving for ECB, CBC decryption and CTR,
resulting in a speedup of ~11% on Marvell ThunderX2, which has a
very deep pipeline and therefore a high issue latency for NEON
instructions operating on the same registers.
Note that XTS is left alone: implementing 5-way interleave there
would either involve spilling of the calculated tweaks to the
stack, or recalculating them after the encryption operation, and
doing either of those would most likely penalize low end cores.
For ECB, this is not a concern at all, given that we have plenty
of spare registers. For CTR and CBC decryption, we take advantage
of the fact that v16 is not used by the CE version of the code
(which is the only one targeted by the optimization), and so we
can reshuffle the code a bit and avoid having to spill to memory
(with the exception of one extra reload in the CBC routine)
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
In preparation of tweaking the accelerated AES chaining mode routines
to be able to use a 5-way stride, implement the core routines to
support processing 5 blocks of input at a time. While at it, drop
the 2 way versions, which have been unused for a while now.
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
icv_ool is not used anymore, drop it.
Fixes: e345177ded17 ("crypto: talitos - fix AEAD processing.")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
On SEC1, hash provides wrong result when performing hashing in several
steps with input data SG list has more than one element. This was
detected with CONFIG_CRYPTO_MANAGER_EXTRA_TESTS:
[ 44.185947] alg: hash: md5-talitos test failed (wrong result) on test vector 6, cfg="random: may_sleep use_finup src_divs=[<reimport>25.88%@+8063, <flush>24.19%@+9588, 28.63%@+16333, <reimport>4.60%@+6756, 16.70%@+16281] dst_divs=[71.61%@alignmask+16361, 14.36%@+7756, 14.3%@+"
[ 44.325122] alg: hash: sha1-talitos test failed (wrong result) on test vector 3, cfg="random: inplace use_final src_divs=[<flush,nosimd>16.56%@+16378, <reimport>52.0%@+16329, 21.42%@alignmask+16380, 10.2%@alignmask+16380] iv_offset=39"
[ 44.493500] alg: hash: sha224-talitos test failed (wrong result) on test vector 4, cfg="random: use_final nosimd src_divs=[<reimport>52.27%@+7401, <reimport>17.34%@+16285, <flush>17.71%@+26, 12.68%@+10644] iv_offset=43"
[ 44.673262] alg: hash: sha256-talitos test failed (wrong result) on test vector 4, cfg="random: may_sleep use_finup src_divs=[<reimport>60.6%@+12790, 17.86%@+1329, <reimport>12.64%@alignmask+16300, 8.29%@+15, 0.40%@+13506, <reimport>0.51%@+16322, <reimport>0.24%@+16339] dst_divs"
This is due to two issues:
- We have an overlap between the buffer used for copying the input
data (SEC1 doesn't do scatter/gather) and the chained descriptor.
- Data copy is wrong when the previous hash left less than one
blocksize of data to hash, implying a complement of the previous
block with a few bytes from the new request.
Fix it by:
- Moving the second descriptor after the buffer, as moving the buffer
after the descriptor would make it more complex for other cipher
operations (AEAD, ABLKCIPHER)
- Skip the bytes taken from the new request to complete the previous
one by moving the SG list forward.
Fixes: 37b5e8897eb5 ("crypto: talitos - chain in buffered data for ahash on SEC1")
Cc: stable@vger.kernel.org
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Moves struct talitos_edesc into talitos.h so that it can be used
from any place in talitos.c
It will be required for next patch ("crypto: talitos - fix hash
on SEC1")
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
All mapping iterator logic is based on the assumption that sg->offset
is always lower than PAGE_SIZE.
But there are situations where sg->offset is such that the SG item
is on the second page. In that case sg_copy_to_buffer() fails
properly copying the data into the buffer. One of the reason is
that the data will be outside the kmapped area used to access that
data.
This patch fixes the issue by adjusting the mapping iterator
offset and pgoffset fields such that offset is always lower than
PAGE_SIZE.
Signed-off-by: Christophe Leroy <christophe.leroy@c-s.fr>
Fixes: 4225fc8555a9 ("lib/scatterlist: use page iterator in the mapping iterator")
Cc: stable@vger.kernel.org
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Michal Suchanek reported [1] that running the pcrypt_aead01 test from
LTP [2] in a loop and holding Ctrl-C causes a NULL dereference of
alg->cra_users.next in crypto_remove_spawns(), via crypto_del_alg().
The test repeatedly uses CRYPTO_MSG_NEWALG and CRYPTO_MSG_DELALG.
The crash occurs when the instance that CRYPTO_MSG_DELALG is trying to
unregister isn't a real registered algorithm, but rather is a "test
larval", which is a special "algorithm" added to the algorithms list
while the real algorithm is still being tested. Larvals don't have
initialized cra_users, so that causes the crash. Normally pcrypt_aead01
doesn't trigger this because CRYPTO_MSG_NEWALG waits for the algorithm
to be tested; however, CRYPTO_MSG_NEWALG returns early when interrupted.
Everything else in the "crypto user configuration" API has this same bug
too, i.e. it inappropriately allows operating on larval algorithms
(though it doesn't look like the other cases can cause a crash).
Fix this by making crypto_alg_match() exclude larval algorithms.
[1] https://lkml.kernel.org/r/20190625071624.27039-1-msuchanek@suse.de
[2] https://github.com/linux-test-project/ltp/blob/20190517/testcases/kernel/crypto/pcrypt_aead01.c
Reported-by: Michal Suchanek <msuchanek@suse.de>
Fixes: a38f7907b926 ("crypto: Add userspace configuration API")
Cc: <stable@vger.kernel.org> # v3.2+
Cc: Steffen Klassert <steffen.klassert@secunet.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
cryptd_skcipher_free() fails to free the struct skcipher_instance
allocated in cryptd_create_skcipher(), leading to a memory leak. This
is detected by kmemleak on bootup on ARM64 platforms:
unreferenced object 0xffff80003377b180 (size 1024):
comm "cryptomgr_probe", pid 822, jiffies 4294894830 (age 52.760s)
backtrace:
kmem_cache_alloc_trace+0x270/0x2d0
cryptd_create+0x990/0x124c
cryptomgr_probe+0x5c/0x1e8
kthread+0x258/0x318
ret_from_fork+0x10/0x1c
Fixes: 4e0958d19bd8 ("crypto: cryptd - Add support for skcipher")
Cc: <stable@vger.kernel.org>
Signed-off-by: Vincent Whitchurch <vincent.whitchurch@axis.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Sometimes mpi_powm will leak karactx because a memory allocation
failure causes a bail-out that skips the freeing of karactx. This
patch moves the freeing of karactx to the end of the function like
everything else so that it can't be skipped.
Reported-by: syzbot+f7baccc38dcc1e094e77@syzkaller.appspotmail.com
Fixes: cdec9cb5167a ("crypto: GnuPG based MPI lib - source files...")
Cc: <stable@vger.kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Provide a keyctl() operation to grant/remove permissions. The grant
operation, wrapped by libkeyutils, looks like:
int ret = keyctl_grant_permission(key_serial_t key,
enum key_ace_subject_type type,
unsigned int subject,
unsigned int perm);
Where key is the key to be modified, type and subject represent the subject
to which permission is to be granted (or removed) and perm is the set of
permissions to be granted. 0 is returned on success. SET_SECURITY
permission is required for this.
The subject type currently must be KEY_ACE_SUBJ_STANDARD for the moment
(other subject types will come along later).
For subject type KEY_ACE_SUBJ_STANDARD, the following subject values are
available:
KEY_ACE_POSSESSOR The possessor of the key
KEY_ACE_OWNER The owner of the key
KEY_ACE_GROUP The key's group
KEY_ACE_EVERYONE Everyone
perm lists the permissions to be granted:
KEY_ACE_VIEW Can view the key metadata
KEY_ACE_READ Can read the key content
KEY_ACE_WRITE Can update/modify the key content
KEY_ACE_SEARCH Can find the key by searching/requesting
KEY_ACE_LINK Can make a link to the key
KEY_ACE_SET_SECURITY Can set security
KEY_ACE_INVAL Can invalidate
KEY_ACE_REVOKE Can revoke
KEY_ACE_JOIN Can join this keyring
KEY_ACE_CLEAR Can clear this keyring
If an ACE already exists for the subject, then the permissions mask will be
overwritten; if perm is 0, it will be deleted.
Currently, the internal ACL is limited to a maximum of 16 entries.
For example:
int ret = keyctl_grant_permission(key,
KEY_ACE_SUBJ_STANDARD,
KEY_ACE_OWNER,
KEY_ACE_VIEW | KEY_ACE_READ);
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/maz/arm-platforms into irq/core
Pull irqchip updates for Linux 5.3 from Marc Zyngier:
- ACPI support for the exiu and mb86s7x drivers
- New Renesas RZ/A1, Amazon al-fic drivers
- Add quirk for Amazon Graviton GICv2m widget
- Large Renesas driver cleanup
- CSky mpintc trigger type fixes
- Meson G12A driver support
- Various minor cleanups
|
|
Continue consolidating Hyper-V clock and timer code into an ISA
independent Hyper-V clocksource driver.
Move the existing clocksource code under drivers/hv and arch/x86 to the new
clocksource driver while separating out the ISA dependencies. Update
Hyper-V initialization to call initialization and cleanup routines since
the Hyper-V synthetic clock is not independently enumerated in ACPI.
Update Hyper-V clocksource users in KVM and VDSO to get definitions from
the new include file.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-3-git-send-email-mikelley@microsoft.com
|
|
Hyper-V clock/timer code and data structures are currently mixed
in with other code in the ISA independent drivers/hv directory as
well as the ISA dependent Hyper-V code under arch/x86.
Consolidate this code and data structures into a Hyper-V clocksource driver
to better follow the Linux model. In doing so, separate out the ISA
dependent portions so the new clocksource driver works for x86 and for the
in-process Hyper-V on ARM64 code.
To start, move the existing clockevents code to create the new clocksource
driver. Update the VMbus driver to call initialization and cleanup routines
since the Hyper-V synthetic timers are not independently enumerated in
ACPI.
No behavior is changed and no new functionality is added.
Suggested-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Michael Kelley <mikelley@microsoft.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: "bp@alien8.de" <bp@alien8.de>
Cc: "will.deacon@arm.com" <will.deacon@arm.com>
Cc: "catalin.marinas@arm.com" <catalin.marinas@arm.com>
Cc: "mark.rutland@arm.com" <mark.rutland@arm.com>
Cc: "linux-arm-kernel@lists.infradead.org" <linux-arm-kernel@lists.infradead.org>
Cc: "gregkh@linuxfoundation.org" <gregkh@linuxfoundation.org>
Cc: "linux-hyperv@vger.kernel.org" <linux-hyperv@vger.kernel.org>
Cc: "olaf@aepfle.de" <olaf@aepfle.de>
Cc: "apw@canonical.com" <apw@canonical.com>
Cc: "jasowang@redhat.com" <jasowang@redhat.com>
Cc: "marcelo.cerri@canonical.com" <marcelo.cerri@canonical.com>
Cc: Sunil Muthuswamy <sunilmut@microsoft.com>
Cc: KY Srinivasan <kys@microsoft.com>
Cc: "sashal@kernel.org" <sashal@kernel.org>
Cc: "vincenzo.frascino@arm.com" <vincenzo.frascino@arm.com>
Cc: "linux-arch@vger.kernel.org" <linux-arch@vger.kernel.org>
Cc: "linux-mips@vger.kernel.org" <linux-mips@vger.kernel.org>
Cc: "linux-kselftest@vger.kernel.org" <linux-kselftest@vger.kernel.org>
Cc: "arnd@arndb.de" <arnd@arndb.de>
Cc: "linux@armlinux.org.uk" <linux@armlinux.org.uk>
Cc: "ralf@linux-mips.org" <ralf@linux-mips.org>
Cc: "paul.burton@mips.com" <paul.burton@mips.com>
Cc: "daniel.lezcano@linaro.org" <daniel.lezcano@linaro.org>
Cc: "salyzyn@android.com" <salyzyn@android.com>
Cc: "pcc@google.com" <pcc@google.com>
Cc: "shuah@kernel.org" <shuah@kernel.org>
Cc: "0x7f454c46@gmail.com" <0x7f454c46@gmail.com>
Cc: "linux@rasmusvillemoes.dk" <linux@rasmusvillemoes.dk>
Cc: "huw@codeweavers.com" <huw@codeweavers.com>
Cc: "sfr@canb.auug.org.au" <sfr@canb.auug.org.au>
Cc: "pbonzini@redhat.com" <pbonzini@redhat.com>
Cc: "rkrcmar@redhat.com" <rkrcmar@redhat.com>
Cc: "kvm@vger.kernel.org" <kvm@vger.kernel.org>
Link: https://lkml.kernel.org/r/1561955054-1838-2-git-send-email-mikelley@microsoft.com
|
|
so the hyper-v clocksource update can be applied.
|
|
gic-pm driver does not use pm-clk interface now and hence the dependency
is removed from Kconfig.
Signed-off-by: Sameer Pujar <spujar@nvidia.com>
Acked-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Controller Driver
The Amazon's Annapurna Labs Fabric Interrupt Controller has 32 inputs.
A FIC (Fabric Interrupt Controller) may be cascaded into another FIC or
directly to the main CPU Interrupt Controller (e.g. GIC).
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Document Amazon's Annapurna Labs Fabric Interrupt Controller SoC binding.
Signed-off-by: Talel Shenhar <talel@amazon.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Quite some time ago the interrupt entry stubs for unused vectors in the
system vector range got removed and directly mapped to the spurious
interrupt vector entry point.
Sounds reasonable, but it's subtly broken. The spurious interrupt vector
entry point pushes vector number 0xFF on the stack which makes the whole
logic in __smp_spurious_interrupt() pointless.
As a consequence any spurious interrupt which comes from a vector != 0xFF
is treated as a real spurious interrupt (vector 0xFF) and not
acknowledged. That subsequently stalls all interrupt vectors of equal and
lower priority, which brings the system to a grinding halt.
This can happen because even on 64-bit the system vector space is not
guaranteed to be fully populated. A full compile time handling of the
unused vectors is not possible because quite some of them are conditonally
populated at runtime.
Bring the entry stubs back, which wastes 160 bytes if all stubs are unused,
but gains the proper handling back. There is no point to selectively spare
some of the stubs which are known at compile time as the required code in
the IDT management would be way larger and convoluted.
Do not route the spurious entries through common_interrupt and do_IRQ() as
the original code did. Route it to smp_spurious_interrupt() which evaluates
the vector number and acts accordingly now that the real vector numbers are
handed in.
Fixup the pr_warn so the actual spurious vector (0xff) is clearly
distiguished from the other vectors and also note for the vectored case
whether it was pending in the ISR or not.
"Spurious APIC interrupt (vector 0xFF) on CPU#0, should never happen."
"Spurious interrupt vector 0xed on CPU#1. Acked."
"Spurious interrupt vector 0xee on CPU#1. Not pending!."
Fixes: 2414e021ac8d ("x86: Avoid building unused IRQ entry stubs")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Cc: Jan Beulich <jbeulich@suse.com>
Link: https://lkml.kernel.org/r/20190628111440.550568228@linutronix.de
|
|
Since the rework of the vector management, warnings about spurious
interrupts have been reported. Robert provided some more information and
did an initial analysis. The following situation leads to these warnings:
CPU 0 CPU 1 IO_APIC
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
clear_vector()
do_IRQ()
-> vector is clear
Before the rework the vector entries of legacy interrupts were statically
assigned and occupied precious vector space while most of them were
unused. Due to that the above situation was handled silently because the
vector was handled and the core handler of the assigned interrupt
descriptor noticed that it is shut down and returned.
While this has been usually observed with legacy interrupts, this situation
is not limited to them. Any other interrupt source, e.g. MSI, can cause the
same issue.
After adding proper synchronization for level triggered interrupts, this
can only happen for edge triggered interrupts where the IO-APIC obviously
cannot provide information about interrupts in flight.
While the spurious warning is actually harmless in this case it worries
users and driver developers.
Handle it gracefully by marking the vector entry as VECTOR_SHUTDOWN instead
of VECTOR_UNUSED when the vector is freed up.
If that above late handling happens the spurious detector will not complain
and switch the entry to VECTOR_UNUSED. Any subsequent spurious interrupt on
that line will trigger the spurious warning as before.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>-
Tested-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.459647741@linutronix.de
|
|
When an interrupt is shut down in free_irq() there might be an inflight
interrupt pending in the IO-APIC remote IRR which is not yet serviced. That
means the interrupt has been sent to the target CPUs local APIC, but the
target CPU is in a state which delays the servicing.
So free_irq() would proceed to free resources and to clear the vector
because synchronize_hardirq() does not see an interrupt handler in
progress.
That can trigger a spurious interrupt warning, which is harmless and just
confuses users, but it also can leave the remote IRR in a stale state
because once the handler is invoked the interrupt resources might be freed
already and therefore acknowledgement is not possible anymore.
Implement the irq_get_irqchip_state() callback for the IO-APIC irq chip. The
callback is invoked from free_irq() via __synchronize_hardirq(). Check the
remote IRR bit of the interrupt and return 'in flight' if it is set and the
interrupt is configured in level mode. For edge mode the remote IRR has no
meaning.
As this is only meaningful for level triggered interrupts this won't cure
the potential spurious interrupt warning for edge triggered interrupts, but
the edge trigger case does not result in stale hardware state. This has to
be addressed at the vector/interrupt entry level seperately.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.370295517@linutronix.de
|
|
free_irq() ensures that no hardware interrupt handler is executing on a
different CPU before actually releasing resources and deactivating the
interrupt completely in a domain hierarchy.
But that does not catch the case where the interrupt is on flight at the
hardware level but not yet serviced by the target CPU. That creates an
interesing race condition:
CPU 0 CPU 1 IRQ CHIP
interrupt is raised
sent to CPU1
Unable to handle
immediately
(interrupts off,
deep idle delay)
mask()
...
free()
shutdown()
synchronize_irq()
release_resources()
do_IRQ()
-> resources are not available
That might be harmless and just trigger a spurious interrupt warning, but
some interrupt chips might get into a wedged state.
Utilize the existing irq_get_irqchip_state() callback for the
synchronization in free_irq().
synchronize_hardirq() is not using this mechanism as it might actually
deadlock unter certain conditions, e.g. when called with interrupts
disabled and the target CPU is the one on which the synchronization is
invoked. synchronize_irq() uses it because that function cannot be called
from non preemtible contexts as it might sleep.
No functional change intended and according to Marc the existing GIC
implementations where the driver supports the callback should be able
to cope with that core change. Famous last words.
Fixes: 464d12309e1b ("x86/vector: Switch IOAPIC to global reservation mode")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Tested-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.279463375@linutronix.de
|
|
The function might sleep, so it cannot be called from interrupt
context. Not even with care.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.189241552@linutronix.de
|
|
When interrupts are shutdown, they are immediately deactivated in the
irqdomain hierarchy. While this looks obviously correct there is a subtle
issue:
There might be an interrupt in flight when free_irq() is invoking the
shutdown. This is properly handled at the irq descriptor / primary handler
level, but the deactivation might completely disable resources which are
required to acknowledge the interrupt.
Split the shutdown code and deactivate the interrupt after synchronization
in free_irq(). Fixup all other usage sites where this is not an issue to
invoke the combined shutdown_and_deactivate() function instead.
This still might be an issue if the interrupt in flight servicing is
delayed on a remote CPU beyond the invocation of synchronize_irq(), but
that cannot be handled at that level and needs to be handled in the
synchronize_irq() context.
Fixes: f8264e34965a ("irqdomain: Introduce new interfaces to support hierarchy irqdomains")
Reported-by: Robert Hodaszi <Robert.Hodaszi@digi.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Link: https://lkml.kernel.org/r/20190628111440.098196390@linutronix.de
|
|
Fix minimum encryption key size check so that HCI_MIN_ENC_KEY_SIZE is
also allowed as stated in the comment.
This bug caused connection problems with devices having maximum
encryption key size of 7 octets (56-bit).
Fixes: 693cd8ce3f88 ("Bluetooth: Fix regression with minimum encryption key size alignment")
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=203997
Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Pull cifs fix from Steve French:
"SMB3 fix (for stable as well) for crash mishandling one of the Windows
reparse point symlink tags"
* tag '5.2-rc6-smb3-fix' of git://git.samba.org/sfrench/cifs-2.6:
cifs: fix crash querying symlinks stored as reparse-points
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux
Pull pidfd fork() fix from Christian Brauner:
"A single small fix for copy_process() in kernel/fork.c:
With Al's removal of ksys_close() from cleanup paths in copy_process()
a bug was introduced. When anon_inode_getfile() failed the cleanup was
correctly performed but the error code was not propagated to callers
of copy_process() causing them to operate on a nonsensical pointer.
The fix is a simple on-liner which makes sure that a proper negative
error code is returned from copy_process().
syzkaller has also verified that the bug is not reproducible with this
fix"
* tag 'for-linus-20190701' of git://git.kernel.org/pub/scm/linux/kernel/git/brauner/linux:
fork: return proper negative error code
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux
Pull arm64 fixes from Will Deacon:
"Fix a build failure with the LLVM linker and a module allocation
failure when KASLR is active:
- Fix module allocation when running with KASLR enabled
- Fix broken build due to bug in LLVM linker (ld.lld)"
* tag 'arm64-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm64/linux:
arm64/efi: Mark __efistub_stext_offset as an absolute symbol explicitly
arm64: kaslr: keep modules inside module region when KASAN is enabled
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci into arm/fixes
This set of patches fixes regressions introduced in v5.2 kernel when DA8xx
OHCI driver was converted over to use GPIO regulators.
* tag 'davinci-fixes-for-v5.2-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/nsekhar/linux-davinci:
ARM: davinci: da830-evm: fix GPIO lookup for OHCI
ARM: davinci: omapl138-hawk: add missing regulator constraints for OHCI
ARM: davinci: da830-evm: add missing regulator constraints for OHCI
+ Linux 5.2-rc7
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value
[ 66.011660] Security negotiation failed.
[ 66.012443] iSCSI Login negotiation failed.
[ 68.413924] general protection fault: 0000 [#1] SMP PTI
[ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1
[ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d4a ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
I ran into an intriguing bug caused by
commit ""spi: gpio: Don't request CS GPIO in DT use-case"
affecting all SPI GPIO devices with an active high
chip select line.
The commit switches the CS gpio handling over to the GPIO
core, which will parse and handle "cs-gpios" from the OF
node without even calling down to the driver to get the
job done.
However the GPIO core handles the standard bindings in
Documentation/devicetree/bindings/spi/spi-controller.yaml
that specifies that active high CS needs to be specified
using "spi-cs-high" in the DT node.
The code in drivers/spi/spi-gpio.c never respected this
and never tried to inspect subnodes to see if they contained
"spi-cs-high" like the gpiolib OF quirks does. Instead the
only way to get an active high CS was to tag it in the
device tree using the flags cell such as
cs-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
This alters the quirks to not inspect the subnodes of SPI
masters on "spi-gpio" for the standard attribute "spi-cs-high",
making old device trees work as expected.
This semantic is a bit ambigous, but just allowing the
flags on the GPIO descriptor to modify polarity is what
the kernel at large mostly uses so let's encourage that.
Fixes: 249e2632dcd0 ("spi: gpio: Don't request CS GPIO in DT use-case")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
ftrace_arch_code_modify_post_process() and ftrace_arch_code_modify_prepare()
ftrace_arch_code_modify_prepare() is acquiring text_mutex, while the
corresponding release is happening in ftrace_arch_code_modify_post_process().
This has already been documented in the code, but let's also make the fact
that this is intentional clear to the semantic analysis tools such as sparse.
Link: http://lkml.kernel.org/r/nycvar.YFH.7.76.1906292321170.27227@cbobk.fhfr.pm
Fixes: 39611265edc1a ("ftrace/x86: Add a comment to why we take text_mutex in ftrace_arch_code_modify_prepare()")
Fixes: d5b844a2cf507 ("ftrace/x86: Remove possible deadlock between register_kprobe() and ftrace_run_update_code()")
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Steven Rostedt (VMware) <rostedt@goodmis.org>
|
|
LINE6 drivers allocate the buffers based on the value returned from
usb_maxpacket() calls. The manipulated device may return zero for
this, and this results in the kmalloc() with zero size (and it may
succeed) while the other part of the driver code writes the packet
data with the fixed size -- which eventually overwrites.
This patch adds a simple sanity check for the invalid buffer size for
avoiding that problem.
Reported-by: syzbot+219f00fb49874dcaea17@syzkaller.appspotmail.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Thomas reported that:
| Background:
|
| In preparation of supporting IPI shorthands I changed the CPU offline
| code to software disable the local APIC instead of just masking it.
| That's done by clearing the APIC_SPIV_APIC_ENABLED bit in the APIC_SPIV
| register.
|
| Failure:
|
| When the CPU comes back online the startup code triggers occasionally
| the warning in apic_pending_intr_clear(). That complains that the IRRs
| are not empty.
|
| The offending vector is the local APIC timer vector who's IRR bit is set
| and stays set.
|
| It took me quite some time to reproduce the issue locally, but now I can
| see what happens.
|
| It requires apicv_enabled=0, i.e. full apic emulation. With apicv_enabled=1
| (and hardware support) it behaves correctly.
|
| Here is the series of events:
|
| Guest CPU
|
| goes down
|
| native_cpu_disable()
|
| apic_soft_disable();
|
| play_dead()
|
| ....
|
| startup()
|
| if (apic_enabled())
| apic_pending_intr_clear() <- Not taken
|
| enable APIC
|
| apic_pending_intr_clear() <- Triggers warning because IRR is stale
|
| When this happens then the deadline timer or the regular APIC timer -
| happens with both, has fired shortly before the APIC is disabled, but the
| interrupt was not serviced because the guest CPU was in an interrupt
| disabled region at that point.
|
| The state of the timer vector ISR/IRR bits:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 1
|
| Now one would assume that the IRR is cleared after the INIT reset, but this
| happens only on CPU0.
|
| Why?
|
| Because our CPU0 hotplug is just for testing to make sure nothing breaks
| and goes through an NMI wakeup vehicle because INIT would send it through
| the boots-trap code which is not really working if that CPU was not
| physically unplugged.
|
| Now looking at a real world APIC the situation in that case is:
|
| ISR IRR
| before apic_soft_disable() 0 1
| after apic_soft_disable() 0 1
|
| On startup 0 0
|
| Why?
|
| Once the dying CPU reenables interrupts the pending interrupt gets
| delivered as a spurious interupt and then the state is clear.
|
| While that CPU0 hotplug test case is surely an esoteric issue, the APIC
| emulation is still wrong, Even if the play_dead() code would not enable
| interrupts then the pending IRR bit would turn into an ISR .. interrupt
| when the APIC is reenabled on startup.
From SDM 10.4.7.2 Local APIC State After It Has Been Software Disabled
* Pending interrupts in the IRR and ISR registers are held and require
masking or handling by the CPU.
In Thomas's testing, hardware cpu will not respect soft disable LAPIC
when IRR has already been set or APICv posted-interrupt is in flight,
so we can skip soft disable APIC checking when clearing IRR and set ISR,
continue to respect soft disable APIC when attempting to set IRR.
Reported-by: Rong Chen <rong.a.chen@intel.com>
Reported-by: Feng Tang <feng.tang@intel.com>
Reported-by: Thomas Gleixner <tglx@linutronix.de>
Tested-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Radim Krčmář <rkrcmar@redhat.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Rong Chen <rong.a.chen@intel.com>
Cc: Feng Tang <feng.tang@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
Currently KVM_STATE_NESTED_EVMCS is used to signal that eVMCS
capability is enabled on vCPU.
As indicated by vmx->nested.enlightened_vmcs_enabled.
This is quite bizarre as userspace VMM should make sure to expose
same vCPU with same CPUID values in both source and destination.
In case vCPU is exposed with eVMCS support on CPUID, it is also
expected to enable KVM_CAP_HYPERV_ENLIGHTENED_VMCS capability.
Therefore, KVM_STATE_NESTED_EVMCS is redundant.
KVM_STATE_NESTED_EVMCS is currently used on restore path
(vmx_set_nested_state()) only to enable eVMCS capability in KVM
and to signal need_vmcs12_sync such that on next VMEntry to guest
nested_sync_from_vmcs12() will be called to sync vmcs12 content
into eVMCS in guest memory.
However, because restore nested-state is rare enough, we could
have just modified vmx_set_nested_state() to always signal
need_vmcs12_sync.
From all the above, it seems that we could have just removed
the usage of KVM_STATE_NESTED_EVMCS. However, in order to preserve
backwards migration compatibility, we cannot do that.
(vmx_get_nested_state() needs to signal flag when migrating from
new kernel to old kernel).
Returning KVM_STATE_NESTED_EVMCS when just vCPU have eVMCS enabled
have a bad side-effect of userspace VMM having to send nested-state
from source to destination as part of migration stream. Even if
guest have never used eVMCS as it doesn't even run a nested
hypervisor workload. This requires destination userspace VMM and
KVM to support setting nested-state. Which make it more difficult
to migrate from new host to older host.
To avoid this, change KVM_STATE_NESTED_EVMCS to signal eVMCS is
not only enabled but also active. i.e. Guest have made some
eVMCS active via an enlightened VMEntry. i.e. vmcs12 is copied
from eVMCS and therefore should be restored into eVMCS resident
in memory (by copy_vmcs12_to_enlightened()).
Reviewed-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Reviewed-by: Maran Wilson <maran.wilson@oracle.com>
Reviewed-by: Krish Sadhukhan <krish.sadhukhan@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
As comment in code specifies, SMM temporarily disables VMX so we cannot
be in guest mode, nor can VMLAUNCH/VMRESUME be pending.
However, code currently assumes that these are the only flags that can be
set on kvm_state->flags. This is not true as KVM_STATE_NESTED_EVMCS
can also be set on this field to signal that eVMCS should be enabled.
Therefore, fix code to check for guest-mode and pending VMLAUNCH/VMRESUME
explicitly.
Reviewed-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Liran Alon <liran.alon@oracle.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
This warning can be triggered easily by userspace, so it should certainly not
cause a panic if panic_on_warn is set.
Reported-by: syzbot+c03f30b4f4c46bdf8575@syzkaller.appspotmail.com
Suggested-by: Alexander Potapenko <glider@google.com>
Acked-by: Alexander Potapenko <glider@google.com>
Signed-off-by: Paolo Bonzini <pbonzini@redhat.com>
|
|
The fixed regulator driver doesn't specify any con_id for gpio lookup
so it must be NULL in the table entry.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Cc: stable@vger.kernel.org
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 1d272894ec4f ("ARM: davinci: omapl138-hawk: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
We need to enable status changes for the fixed power supply for the USB
controller.
Fixes: 274e4c336192 ("ARM: davinci: da830-evm: add a fixed regulator for ohci-da8xx")
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
|
|
AP Queue Interruption Control (AQIC) facility gives
the guest the possibility to control interruption for
the Cryptographic Adjunct Processor queues.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
[ Modified while picking: we may not expose STFLE facility 65
unconditionally because AIV is a pre-requirement.]
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We register a AP PQAP instruction hook during the open
of the mediated device. And unregister it on release.
During the probe of the AP device, we allocate a vfio_ap_queue
structure to keep track of the information we need for the
PQAP/AQIC instruction interception.
In the AP PQAP instruction hook, if we receive a demand to
enable IRQs,
- we retrieve the vfio_ap_queue based on the APQN we receive
in REG1,
- we retrieve the page of the guest address, (NIB), from
register REG2
- we retrieve the mediated device to use the VFIO pinning
infrastructure to pin the page of the guest address,
- we retrieve the pointer to KVM to register the guest ISC
and retrieve the host ISC
- finaly we activate GISA
If we receive a demand to disable IRQs,
- we deactivate GISA
- unregister from the GIB
- unpin the NIB
When removing the AP device from the driver the device is
reseted and this process unregisters the GISA from the GIB,
and unpins the NIB address then we free the vfio_ap_queue
structure.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
To be able to use the VFIO interface to facilitate the
mediated device memory pinning/unpinning we need to register
a notifier for IOMMU.
While we will start to pin one guest page for the interrupt indicator
byte, this is still ok with ballooning as this page will never be
used by the guest virtio-balloon driver.
So the pinned page will never be freed. And even a broken guest does
so, that would not impact the host as the original page is still
in control by vfio.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We prepare the interception of the PQAP/AQIC instruction for
the case the AQIC facility is enabled in the guest.
First of all we do not want to change existing behavior when
intercepting AP instructions without the SIE allowing the guest
to use AP instructions.
In this patch we only handle the AQIC interception allowed by
facility 65 which will be enabled when the complete interception
infrastructure will be present.
We add a callback inside the KVM arch structure for s390 for
a VFIO driver to handle a specific response to the PQAP
instruction with the AQIC command and only this command.
But we want to be able to return a correct answer to the guest
even there is no VFIO AP driver in the kernel.
Therefor, we inject the correct exceptions from inside KVM for the
case the callback is not initialized, which happens when the vfio_ap
driver is not loaded.
We do consider the responsibility of the driver to always initialize
the PQAP callback if it defines queues by initializing the CRYCB for
a guest.
If the callback has been setup we call it.
If not we setup an answer considering that no queue is available
for the guest when no callback has been setup.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Kasan instrumentation of backchain unwinder stack reads is disabled
completely and simply uses READ_ONCE_NOCHECK now.
READ_ONCE_TASK_STACK macro is unused and could be removed.
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Avoid kasan false positive when current task is interrupted in-between
stack frame allocation and backchain write instructions leaving new stack
frame backchain invalid. In particular if backchain is 0 the unwinder
tries to read pt_regs from the stack and might hit kasan poisoned bytes,
leading to kasan "stack-out-of-bounds" report.
Disable kasan instrumentation of unwinder stack reads, since this
limitation couldn't be handled otherwise with current backchain unwinder
implementation.
Fixes: 78c98f907413 ("s390/unwind: introduce stack unwind API")
Reported-by: Julian Wiedmann <jwi@linux.ibm.com>
Tested-by: Benjamin Block <bblock@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
