| Age | Commit message (Collapse) | Author |
|---|
|
Commit 73118ca8baf7 introduced a glock reference counting bug in
gfs2_trans_remove_revoke. Given that, replacing gl_revokes with a GLF flag is
no longer useful, so revert that commit.
Signed-off-by: Bob Peterson <rpeterso@redhat.com>
Signed-off-by: Andreas Gruenbacher <agruenba@redhat.com>
|
|
git://people.freedesktop.org/~gabbayo/linux into char-misc-linus
Oded writes:
This tag contains the following fixes:
- Fix the code that checks whether we can use 2MB page size when mapping
memory in the ASIC's MMU. The current code had a "hole" which happened
in architectures other then x86-64.
- Fix the debugfs interface to read/write from/to the device using device
virtual addresses. There was a bug in the translation regarding
addresses that were mapped using 2MB page size.
- Fix a bug in the debug/profiling code, where the code didn't read the
full address but only the lower 32-bits of the address.
* tag 'misc-habanalabs-fixes-2019-06-06' of git://people.freedesktop.org/~gabbayo/linux:
habanalabs: Read upper bits of trace buffer from RWPHI
habanalabs: Fix virtual address access via debugfs for 2MB pages
habanalabs: fix bug in checking huge page optimization
|
|
Since GCC 9, the compiler warns about evolution of the
platform-specific ABI, in particular relating for the marshaling of
certain structures involving bitfields.
The kernel is a standalone binary, and of course nobody would be
so stupid as to expose structs containing bitfields as function
arguments in ABI. (Passing a pointer to such a struct, however
inadvisable, should be unaffected by this change. perf and various
drivers rely on that.)
So these warnings do more harm than good: turn them off.
We may miss warnings about future ABI drift, but that's too bad.
Future ABI breaks of this class will have to be debugged and fixed
the traditional way unless the compiler evolves finer-grained
diagnostics.
Signed-off-by: Dave Martin <Dave.Martin@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
According to the found documentation, data cache flushes and sync
instructions are needed on the PCX-U+ (PA8200, e.g. C200/C240)
platforms, while PCX-W (PA8500, e.g. C360) platforms aparently don't
need those flushes when changing the IO PDIR data structures.
We have no documentation for PCX-W+ (PA8600) and PCX-W2 (PA8700) CPUs,
but Carlo Pisani reported that his C3600 machine (PA8600, PCX-W+) fails
when the fdc instructions were removed. His firmware didn't set the NIOP
bit, so one may assume it's a firmware bug since other C3750 machines
had the bit set.
Even if documentation (as mentioned above) states that PCX-W (PA8500,
e.g. J5000) does not need fdc flushes, Sven could show that an Adaptec
29320A PCI-X SCSI controller reliably failed on a dd command during the
first five minutes in his J5000 when fdc flushes were missing.
Going forward, we will now NOT replace the fdc and sync assembler
instructions by NOPS if:
a) the NP iopdir_fdc bit was set by firmware, or
b) we find a CPU up to and including a PCX-W+ (PA8600).
This fixes the HPMC crashes on a C240 and C36XX machines. For other
machines we rely on the firmware to set the bit when needed.
In case one finds HPMC issues, people could try to boot their machines
with the "no-alternatives" kernel option to turn off any alternative
patching.
Reported-by: Sven Schnelle <svens@stackframe.org>
Reported-by: Carlo Pisani <carlojpisani@gmail.com>
Tested-by: Sven Schnelle <svens@stackframe.org>
Fixes: 3847dab77421 ("parisc: Add alternative coding infrastructure")
Signed-off-by: Helge Deller <deller@gmx.de>
Cc: stable@vger.kernel.org # 5.0+
|
|
Most I/O in the kernel is done using the kernel offset mapping.
However, there is one API that uses aliased kernel address ranges:
> The final category of APIs is for I/O to deliberately aliased address
> ranges inside the kernel. Such aliases are set up by use of the
> vmap/vmalloc API. Since kernel I/O goes via physical pages, the I/O
> subsystem assumes that the user mapping and kernel offset mapping are
> the only aliases. This isn't true for vmap aliases, so anything in
> the kernel trying to do I/O to vmap areas must manually manage
> coherency. It must do this by flushing the vmap range before doing
> I/O and invalidating it after the I/O returns.
For this reason, we should use the hardware lpa instruction to load the
physical address of kernel virtual addresses in the driver code.
I believe we only use the vmap/vmalloc API with old PA 1.x processors
which don't have a sba, so we don't hit this problem.
Tested on c3750, c8000 and rp3440.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
Remove the CONFIG_UEVENT_HELPER_PATH because:
1. It is disabled since commit 1be01d4a5714 ("driver: base: Disable
CONFIG_UEVENT_HELPER by default") as its dependency (UEVENT_HELPER) was
made default to 'n',
2. It is not recommended (help message: "This should not be used today
[...] creates a high system load") and was kept only for ancient
userland,
3. Certain userland specifically requests it to be disabled (systemd
README: "Legacy hotplug slows down the system and confuses udev").
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
index of I/O pdirs
We only support I/O to kernel space. Using %sr1 to load the coherence
index may be racy unless interrupts are disabled. This patch changes the
code used to load the coherence index to use implicit space register
selection. This saves one instruction and eliminates the race.
Tested on rp3440, c8000 and c3750.
Signed-off-by: John David Anglin <dave.anglin@bell.net>
Cc: stable@vger.kernel.org
Signed-off-by: Helge Deller <deller@gmx.de>
|
|
In case of error, the function devm_ioremap_resource() returns ERR_PTR()
and never returns NULL. The NULL test in the return value check should
be replaced with IS_ERR().
This issue was detected by using the Coccinelle software.
Fixes: 408b56ca5c8e ("usb: gadget: udc: lpc32xx: simplify probe")
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Acked-by: Vladimir Zapolskiy <vz@mleia.com>
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The patch 10209abe87f5ebfd482a00323f5236d6094d0865
usb: dwc2: gadget: Add scatter-gather mode
avoided a NULL pointer dereference (hs_ep->req == NULL) by
calling dwc2_gadget_fill_nonisoc_xfer_dma_one() directly instead of through
the dwc2_gadget_config_nonisoc_xfer_ddma() wrapper, which unconditionally
dereferenced the said pointer.
However, this was based on an incorrect assumption that in the context of
dwc2_hsotg_program_zlp() the pointer is always NULL, which is not the case.
The result were SB CV MSC tests failing starting from Test Case 6.
Instead, this patch reverts to calling the wrapper and adds a check for
the pointer being NULL inside the wrapper.
Fixes: 10209abe87f5 (usb: dwc2: gadget: Add scatter-gather mode)
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Andrzej Pietrasiewicz <andrzej.p@collabora.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
On ISOC OUT transfer completion, in none DDMA mode, set actual frame
number returning to function driver in usb_request.
Signed-off-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Gadget drivers may queue request in interrupt context. This would lead to
a descriptor allocation in that context. In that case we would hit
BUG_ON(in_interrupt()) in __get_vm_area_node.
Also remove the unnecessary cast.
Acked-by: Sylvain Lemieux <slemieux.tyco@gmail.com>
Tested-by: James Grant <jamesg@zaltys.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There is no deallocation of fusb300->ep[i] elements, allocated at
fusb300_probe.
The patch adds deallocation of fusb300->ep array elements.
Signed-off-by: Young Xiao <92siuyang@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Since this driver already handles changer detction state, copy the
workaround code currently residing in arch/arm/mach-imx/anatop.c into
this drier to consolidate the places modifying it.
Signed-off-by: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: Chris Healy <cphealy@gmail.com>
Cc: Felipe Balbi <balbi@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: linux-usb@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-kernel@vger.kernel.org
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Insert a padding between data and the stored_xfer_buffer pointer to
ensure they are not on the same cache line.
Otherwise, the stored_xfer_buffer gets corrupted for IN URBs on
non-cache-coherent systems. (In my case: Lantiq xRX200 MIPS)
Fixes: 3bc04e28a030 ("usb: dwc2: host: Get aligned DMA in a more supported way")
Fixes: 56406e017a88 ("usb: dwc2: Fix DMA alignment to start at allocated boundary")
Cc: <stable@vger.kernel.org>
Tested-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Signed-off-by: Martin Schiller <ms@dev.tdt.de>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In commit abb621844f6a ("usb: ch9: make usb_endpoint_maxp() return
only packet size") the API to usb_endpoint_maxp() changed. It used to
just return wMaxPacketSize but after that commit it returned
wMaxPacketSize with the high bits (the multiplier) masked off. If you
wanted to get the multiplier it was now up to your code to call the
new usb_endpoint_maxp_mult() which was introduced in
commit 541b6fe63023 ("usb: add helper to extract bits 12:11 of
wMaxPacketSize").
Prior to the API change most host drivers were updated, but no update
was made to dwc2. Presumably it was assumed that dwc2 was too
simplistic to use the multiplier and thus just didn't support a
certain class of USB devices. However, it turns out that dwc2 did use
the multiplier and many devices using it were working quite nicely.
That means that many USB devices have been broken since the API
change. One such device is a Logitech HD Pro Webcam C920.
Specifically, though dwc2 didn't directly call usb_endpoint_maxp(), it
did call usb_maxpacket() which in turn called usb_endpoint_maxp().
Let's update dwc2 to work properly with the new API.
Fixes: abb621844f6a ("usb: ch9: make usb_endpoint_maxp() return only packet size")
Cc: stable@vger.kernel.org
Acked-by: Minas Harutyunyan <hminas@synopsys.com>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix a s/TIF_SECOMP/TIF_SECCOMP/ comment typo
Cc: Jiri Kosina <trivial@kernel.org>
Reviewed-by: Kees Cook <keescook@chromium.org
Signed-off-by: George G. Davis <george_davis@mentor.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
We need to check whether drm_atomic_get_crtc_state() returns an error
pointer before dereferencing "crtc_st".
Fixes: 9e5603094176 ("drm/komeda: Add komeda_plane/plane_helper_funcs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: "james qian wang (Arm Technology China)" <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c: In function komeda_plane_atomic_check:
drivers/gpu/drm/arm/display/komeda/komeda_plane.c:49:22: warning: variable kcrtc set but not used [-Wunused-but-set-variable]
It is never used since introduction in
commit 9e5603094176 ("drm/komeda: Add komeda_plane/plane_helper_funcs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Reviewed-by: James Qian Wang (Arm Technology China) <james.qian.wang@arm.com>
Signed-off-by: Liviu Dudau <liviu.dudau@arm.com>
|
|
Add the CPUID model numbers of Icelake (ICL) desktop and server
processors to the Intel family list.
[ Qiuxu: Sort the macros by model number. ]
Signed-off-by: Kan Liang <kan.liang@linux.intel.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Cc: "H. Peter Anvin" <hpa@zytor.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Rajneesh Bhardwaj <rajneesh.bhardwaj@linux.intel.com>
Cc: rui.zhang@intel.com
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Tony Luck <tony.luck@intel.com>
Cc: x86-ml <x86@kernel.org>
Link: https://lkml.kernel.org/r/20190603134122.13853-1-kan.liang@linux.intel.com
|
|
Clear the CRYPTO_TFM_REQ_MAY_SLEEP flag when the chacha20poly1305
operation is being continued from an async completion callback, since
sleeping may not be allowed in that context.
This is basically the same bug that was recently fixed in the xts and
lrw templates. But, it's always been broken in chacha20poly1305 too.
This was found using syzkaller in combination with the updated crypto
self-tests which actually test the MAY_SLEEP flag now.
Reproducer:
python -c 'import socket; socket.socket(socket.AF_ALG, 5, 0).bind(
("aead", "rfc7539(cryptd(chacha20-generic),poly1305-generic)"))'
Kernel output:
BUG: sleeping function called from invalid context at include/crypto/algapi.h:426
in_atomic(): 1, irqs_disabled(): 0, pid: 1001, name: kworker/2:2
[...]
CPU: 2 PID: 1001 Comm: kworker/2:2 Not tainted 5.2.0-rc2 #5
Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.12.0-20181126_142135-anatol 04/01/2014
Workqueue: crypto cryptd_queue_worker
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x4d/0x6a lib/dump_stack.c:113
___might_sleep kernel/sched/core.c:6138 [inline]
___might_sleep.cold.19+0x8e/0x9f kernel/sched/core.c:6095
crypto_yield include/crypto/algapi.h:426 [inline]
crypto_hash_walk_done+0xd6/0x100 crypto/ahash.c:113
shash_ahash_update+0x41/0x60 crypto/shash.c:251
shash_async_update+0xd/0x10 crypto/shash.c:260
crypto_ahash_update include/crypto/hash.h:539 [inline]
poly_setkey+0xf6/0x130 crypto/chacha20poly1305.c:337
poly_init+0x51/0x60 crypto/chacha20poly1305.c:364
async_done_continue crypto/chacha20poly1305.c:78 [inline]
poly_genkey_done+0x15/0x30 crypto/chacha20poly1305.c:369
cryptd_skcipher_complete+0x29/0x70 crypto/cryptd.c:279
cryptd_skcipher_decrypt+0xcd/0x110 crypto/cryptd.c:339
cryptd_queue_worker+0x70/0xa0 crypto/cryptd.c:184
process_one_work+0x1ed/0x420 kernel/workqueue.c:2269
worker_thread+0x3e/0x3a0 kernel/workqueue.c:2415
kthread+0x11f/0x140 kernel/kthread.c:255
ret_from_fork+0x1f/0x30 arch/x86/entry/entry_64.S:352
Fixes: 71ebc4d1b27d ("crypto: chacha20poly1305 - Add a ChaCha20-Poly1305 AEAD construction, RFC7539")
Cc: <stable@vger.kernel.org> # v4.2+
Cc: Martin Willi <martin@strongswan.org>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
If CRYPTO_DEV_ATMEL_ECC is set m, which select CRC16 to m,
while CRYPTO_DEV_ATMEL_SHA204A is set to y, building fails.
drivers/crypto/atmel-i2c.o: In function 'atmel_i2c_checksum':
atmel-i2c.c:(.text+0x16): undefined reference to 'crc16'
Add CRC16 dependency to CRYPTO_DEV_ATMEL_SHA204A
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: da001fb651b0 ("crypto: atmel-i2c - add support for SHA204A random number generator")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Disabled the check and set of 'mem' and 'emi_slow'
clocks, since these are not available for iMX7ULP.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The CAAM driver currently violates an undocumented and slightly
controversial requirement imposed by the crypto stack that a buffer
referred to by the request structure via its virtual address may not
be modified while any scatterlists passed via the same request
structure are mapped for inbound DMA.
This may result in errors like
alg: aead: decryption failed on test 1 for gcm_base(ctr-aes-caam,ghash-generic): ret=74
alg: aead: Failed to load transform for gcm(aes): -2
on non-cache coherent systems, due to the fact that the GCM driver
passes an IV buffer by virtual address which shares a cacheline with
the auth_tag buffer passed via a scatterlist, resulting in corruption
of the auth_tag when the IV is updated while the DMA mapping is live.
Since the IV that is returned to the caller is only valid for CBC mode,
and given that the in-kernel users of CBC (such as CTS) don't trigger the
same issue as the GCM driver, let's just disable the output IV generation
for all modes except CBC for the time being.
Fixes: 854b06f76879 ("crypto: caam - properly set IV after {en,de}crypt")
Cc: Horia Geanta <horia.geanta@nxp.com>
Cc: Iuliana Prodan <iuliana.prodan@nxp.com>
Reported-by: Sascha Hauer <s.hauer@pengutronix.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The param2 member in atmel_i2c_cmd is supposed to be little-endian
but was marked as u16. This patch changes it to a __le16 which
reveals a missing endian swap in atmel_i2c_init_read_cmd.
Another missing little-endian marking is also added in
atmel_i2c_checksum.
Fixes: 11105693fa05 ("crypto: atmel-ecc - introduce Microchip...")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Commit c778f96bf347 ("crypto: lrw - Optimize tweak computation")
incorrectly reduced the alignmask of LRW instances from
'__alignof__(u64) - 1' to '__alignof__(__be32) - 1'.
However, xor_tweak() and setkey() assume that the data and key,
respectively, are aligned to 'be128', which has u64 alignment.
Fix the alignmask to be at least '__alignof__(be128) - 1'.
Fixes: c778f96bf347 ("crypto: lrw - Optimize tweak computation")
Cc: <stable@vger.kernel.org> # v4.20+
Cc: Ondrej Mosnacek <omosnace@redhat.com>
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Changing ghash_mod_init() to be subsys_initcall made it start running
before the alignment fault handler has been installed on ARM. In kernel
builds where the keys in the ghash test vectors happened to be
misaligned in the kernel image, this exposed the longstanding bug that
ghash_setkey() is incorrectly casting the key buffer (which can have any
alignment) to be128 for passing to gf128mul_init_4k_lle().
Fix this by memcpy()ing the key to a temporary buffer.
Don't fix it by setting an alignmask on the algorithm instead because
that would unnecessarily force alignment of the data too.
Fixes: 2cdc6899a88e ("crypto: ghash - Add GHASH digest algorithm for GCM")
Reported-by: Peter Robinson <pbrobinson@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Eric Biggers <ebiggers@google.com>
Tested-by: Peter Robinson <pbrobinson@gmail.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
xxhash is currently implemented as a self-contained module in /lib.
This patch enables that module to be used as part of the generic kernel
crypto framework. It adds a simple wrapper to the 64bit version.
I've also added test vectors (with help from Nick Terrell). The upstream
xxhash code is tested by running hashing operation on random 222 byte
data with seed values of 0 and a prime number. The upstream test
suite can be found at https://github.com/Cyan4973/xxHash/blob/cf46e0c/xxhsum.c#L664
Essentially hashing is run on data of length 0,1,14,222 with the
aforementioned seed values 0 and prime 2654435761. The particular random
222 byte string was provided to me by Nick Terrell by reading
/dev/random and the checksums were calculated by the upstream xxsum
utility with the following bash script:
dd if=/dev/random of=TEST_VECTOR bs=1 count=222
for a in 0 1; do
for l in 0 1 14 222; do
for s in 0 2654435761; do
echo algo $a length $l seed $s;
head -c $l TEST_VECTOR | ~/projects/kernel/xxHash/xxhsum -H$a -s$s
done
done
done
This produces output as follows:
algo 0 length 0 seed 0
02cc5d05 stdin
algo 0 length 0 seed 2654435761
02cc5d05 stdin
algo 0 length 1 seed 0
25201171 stdin
algo 0 length 1 seed 2654435761
25201171 stdin
algo 0 length 14 seed 0
c1d95975 stdin
algo 0 length 14 seed 2654435761
c1d95975 stdin
algo 0 length 222 seed 0
b38662a6 stdin
algo 0 length 222 seed 2654435761
b38662a6 stdin
algo 1 length 0 seed 0
ef46db3751d8e999 stdin
algo 1 length 0 seed 2654435761
ac75fda2929b17ef stdin
algo 1 length 1 seed 0
27c3f04c2881203a stdin
algo 1 length 1 seed 2654435761
4a15ed26415dfe4d stdin
algo 1 length 14 seed 0
3d33dc700231dfad stdin
algo 1 length 14 seed 2654435761
ea5f7ddef9a64f80 stdin
algo 1 length 222 seed 0
5f3d3c08ec2bef34 stdin
algo 1 length 222 seed 2654435761
6a9df59664c7ed62 stdin
algo 1 is xx64 variant, algo 0 is the 32 bit variant which is currently
not hooked up.
Signed-off-by: Nikolay Borisov <nborisov@suse.com>
Reviewed-by: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The Jitter RNG implementation is updated to comply with upstream version
2.1.2. The change covers the following aspects:
* Time variation measurement is conducted over the LFSR operation
instead of the XOR folding
* Invcation of stuck test during initialization
* Removal of the stirring functionality and the Von-Neumann
unbiaser as the LFSR using a primitive and irreducible polynomial
generates an identical distribution of random bits
This implementation was successfully used in FIPS 140-2 validations
as well as in German BSI evaluations.
This kernel implementation was tested as follows:
* The unchanged kernel code file jitterentropy.c is compiled as part
of user space application to generate raw unconditioned noise
data. That data is processed with the NIST SP800-90B non-IID test
tool to verify that the kernel code exhibits an equal amount of noise
as the upstream Jitter RNG version 2.1.2.
* Using AF_ALG with the libkcapi tool of kcapi-rng the Jitter RNG was
output tested with dieharder to verify that the output does not
exhibit statistical weaknesses. The following command was used:
kcapi-rng -n "jitterentropy_rng" -b 100000000000 | dieharder -a -g 200
* The unchanged kernel code file jitterentropy.c is compiled as part
of user space application to test the LFSR implementation. The
LFSR is injected a monotonically increasing counter as input and
the output is fed into dieharder to verify that the LFSR operation
does not exhibit statistical weaknesses.
* The patch was tested on the Muen separation kernel which returns
a more coarse time stamp to verify that the Jitter RNG does not cause
regressions with its initialization test considering that the Jitter
RNG depends on a high-resolution timer.
Tested-by: Reto Buerki <reet@codelabs.ch>
Signed-off-by: Stephan Mueller <smueller@chronox.de>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For hash algorithms implemented using the "shash" algorithm type, test
both the ahash and shash APIs, not just the ahash API.
Testing the ahash API already tests the shash API indirectly, which is
normally good enough. However, there have been corner cases where there
have been shash bugs that don't get exposed through the ahash API. So,
update testmgr to test the shash API too.
This would have detected the arm64 SHA-1 and SHA-2 bugs for which fixes
were just sent out (https://patchwork.kernel.org/patch/10964843/ and
https://patchwork.kernel.org/patch/10965089/):
alg: shash: sha1-ce test failed (wrong result) on test vector 0, cfg="init+finup aligned buffer"
alg: shash: sha224-ce test failed (wrong result) on test vector 0, cfg="init+finup aligned buffer"
alg: shash: sha256-ce test failed (wrong result) on test vector 0, cfg="init+finup aligned buffer"
This also would have detected the bugs fixed by commit 307508d10729
("crypto: crct10dif-generic - fix use via crypto_shash_digest()") and
commit dec3d0b1071a
("crypto: x86/crct10dif-pcl - fix use via crypto_shash_digest()").
Signed-off-by: Eric Biggers <ebiggers@google.com>
Acked-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The sha256-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: the actual digest, result: initial
value of SHA internal state. The error is in sha256_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha2_ce_transform to make the final round. However, in
sha256_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 03802f6a80b3a ("crypto: arm64/sha2-ce - move SHA-224/256 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The sha1-ce finup implementation for ARM64 produces wrong digest
for empty input (len=0). Expected: da39a3ee..., result: 67452301...
(initial value of SHA internal state). The error is in sha1_ce_finup:
for empty data `finalize` will be 1, so the code is relying on
sha1_ce_transform to make the final round. However, in
sha1_base_do_update, the block function will not be called when
len == 0.
Fix it by setting finalize to 0 if data is empty.
Fixes: 07eb54d306f4 ("crypto: arm64/sha1-ce - move SHA-1 ARMv8 implementation to base layer")
Cc: stable@vger.kernel.org
Signed-off-by: Elena Petrova <lenaptr@google.com>
Reviewed-by: Ard Biesheuvel <ard.biesheuvel@linaro.org>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
For rsa and pkcs1pad, CAAM expects an input of modulus size.
For this we strip the leading zeros in case the size is more than modulus.
This commit avoids modifying the crypto request while stripping zeros from
input, to comply with the crypto API requirement. This is done by adding
a fixup input pointer and length.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geanta <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The problem is with the input data size sent to CAAM for encrypt/decrypt.
Pkcs1pad is failing due to pkcs1 padding done in SW starting with0x01
instead of 0x00 0x01.
CAAM expects an input of modulus size. For this we strip the leading
zeros in case the size is more than modulus or pad the input with zeros
until the modulus size is reached.
Signed-off-by: Iuliana Prodan <iuliana.prodan@nxp.com>
Reviewed-by: Horia Geantă <horia.geanta@nxp.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
descriptors
When performing a transformation the hardware is given result
descriptors to save the result data. Those result descriptors are
batched using a 'first' and a 'last' bit. There are cases were more
descriptors than needed are given to the engine, leading to the engine
only using some of them, and not setting the last bit on the last
descriptor we gave. This causes issues were the driver and the hardware
aren't in sync anymore about the number of result descriptors given (as
the driver do not give a pool of descriptor to use for any
transformation, but a pool of descriptors to use *per* transformation).
This patch fixes it by attaching the number of given result descriptors
to the requests, and by using this number instead of the 'last' bit
found on the descriptors to process them.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Replace sg_nents_for_len by sg_nents when DMA mapping/unmapping buffers
and when looping over the SG entries. This fix cases where the SG
entries aren't used fully, which would in such cases led to using fewer
SG entries than needed (and thus the engine wouldn't have access to the
full input data and the result would be wrong).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds support for HMAC updates in the Inside Secure SafeXcel
crypto engine driver. Updates were supported for hash algorithms, but
were never enabled for HMAC ones. This fixes boot time test issues.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch adds support for retrieving intermediate IV from the crypto
engine when using the CBC block mode with AES and (3)DES. The retrieved
IV is copied to the request IV buffer, as requested by the kernel crypto
API.
This fix boot tests added by
commit 8efd972ef96a ("crypto: testmgr - support checking skcipher output IV").
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch fixes the queued len computation, which could theoretically
be wrong if req->len[1] - req->processed[1] > 1. Be future-proof here,
and fix it.
Fixes: b460edb6230a ("crypto: inside-secure - sha512 support")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
A request is zeroed in safexcel_ahash_exit_inv(). This request total
size is EIP197_AHASH_REQ_SIZE while the memset zeroing it uses
sizeof(struct ahash_request), which happens to be less than
EIP197_AHASH_REQ_SIZE. This patch fixes it.
Fixes: f6beaea30487 ("crypto: inside-secure - authenc(hmac(sha256), cbc(aes)) support")
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch unify the way the cache related data is zeroed when the cache
buffer is DMA unmapped. It should not change the driver behaviour, but
improves the code safety and readability.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The context given to the crypto engine can be reused over time. While
the driver was designed to allow this, the feature wasn't enabled in the
hardware engine. This patch enables it.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This patch changes the error reported by the Inside Secure SafeXcel
driver when a result descriptor reports an error, from -EIO to -EINVAL,
as this is what the crypto framework expects. This was found while
running the crypto extra tests.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
The result descriptors contain errors, which are represented as a
bitmap. This patch updates the error message to not treat the error as a
decimal value, but as an hexadecimal one. This helps in knowing the
value does not have a direct meaning (the set bits themselves have).
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
When sending an ahash request, the code checks for the extra variable
not to be 0. This check is useless as the extra variable can't be 0 at
this point (it is checked on the line just before).
This patch does not modify the driver behaviour in any way.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This cosmetic patch fixes a cosmetic issue with if brackets.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
This cosmetic patch moves a comment before the condition it is related
to. The patch does not change the driver behaviour in any way.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
Cosmetic patch removing an empty line in the skcipher token creation
routine.
Signed-off-by: Antoine Tenart <antoine.tenart@bootlin.com>
Signed-off-by: Herbert Xu <herbert@gondor.apana.org.au>
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- Allow fb changes in async commits (fixes igt failures) (Helen)
- Actually unmap the scatterlist when unmapping udmabuf (Lucas)
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605210335.GA35431@art_vandelay
|
|
into drm-fixes
- A fix to make VCE resume more reliable
- Updates for new raven variants
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190605182332.4073-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-intel into drm-fixes
- Add missing Icelake W/A to disable GPU hang on cache ECC error
- GVT a fix for recently seen arbitrary DMA map fault and more enforcement fixes.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190603132928.GA4866@jlahtine-desk.ger.corp.intel.com
|
