| Age | Commit message (Collapse) | Author |
|---|
|
Today, the length of a debug message in iwl_trans_pcie_reclaim
may pass the MAX_MSG_LEN, which is 110.
An example for this kind of message is:
'iwl_trans_pcie_reclaim: Read index for DMA queue txq id (2),
last_to_free 65535 is out of range [0-65536] 2 2.'
Cut the message a bit so it will fit the allowed MAX_MSG_LEN.
Signed-off-by: Golan Ben Ami <golan.ben.ami@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If the HW is not responding at probe time, fail immediately complaining
about it. Without this, we see that the kernel spends > 100ms trying to
load firmware (even gives an incorrect impression that it actually
loaded a firmware) and do unnecesary processing before concluding that
the device is not accessible:
INFO kernel: [ 34.092678] iwlwifi 0000:01:00.0: enabling device (0000 -> 0002)
WARNING kernel: [ 34.093560] iwlwifi 0000:01:00.0: Direct firmware load for iwl-dbg-cfg.ini failed with error -2
INFO kernel: [ 34.111523] iwlwifi 0000:01:00.0: loaded firmware version 17.318154.0 op_mode iwlmvm
INFO kernel: [ 34.173250] iwlwifi 0000:01:00.0: Detected Intel(R) Dual Band Wireless AC 7265, REV=0xFFFFFFFF
ERR kernel: [ 34.198023] iwlwifi 0000:01:00.0: iwlwifi transaction failed, dumping registers
ERR kernel: [ 34.198044] iwlwifi 0000:01:00.0: iwlwifi device config registers:
Signed-off-by: Rajat Jain <rajatja@google.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
This will allow us to reuse the function later for adding fraglist
SKBs to the TFD.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When anything fails, we unmap the whole TFD in three different
places scattered throughout the code. Unify this to a single
place.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If the incoming frame should be an A-MSDU, it may already be one,
for example in the case of NAN multicast being encapsulated in an
A-MSDU. Thus, use the GSO algorithm to build A-MSDU only if the
skb actually contains GSO data.
Fixes: 6ffe5de35b05 ("iwlwifi: pcie: add AMSDU to gen2")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the skb fragment loop into a helper routine to be able
to reuse it later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Annotate the compressed BA notification array sizes and
make both of them 0-length since the length of 1 is just
confusing - it may be different than that and the offset
to the second one needs to be calculated in the C code
anyhow.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Make the adjustments for gen2 TX and RX of TKIP packets. Strip MIC on
RX. Don't add IV space and keep the MIC space zeroed on TX.
Devices that support gen2 data path support TKIP only in station mode.
In all other modes, fall back to SW encryption. Do this early in the
set_key() callback so that the key flags would not be incorrectly set.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Ilan Peer <ilan.peer@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
For newer devices we have higher range of periphery
addresses. Currently it is masked out, so we end up
reading another address.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In order to receive TB (Trigger Based) PPDU in monitor mode,
the Driver must send the HE_AIR_SNIFFER_CONFIG_CMD host command.
Enable that via debugfs.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Ido Yariv <idox.yariv@intel.com>
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
CDB support has nothing to do with non unified image.
Signed-off-by: Haim Dreyfuss <haim.dreyfuss@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The non-shared antenna was wrong for 22000 device series.
Fix it to ANT_B for correct antenna preference by coex in MVM driver.
Fixes: e34d975e40ff ("iwlwifi: Add a000 HW family support")
Signed-off-by: Erel Geron <erelx.geron@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We can dump data from the firmware either when it crashes,
or when the firmware is alive.
Not all the data is available if the firmware is running
(like the Tx / Rx FIFOs which are available only when the
firmware is halted), so we first check that the firmware
is alive to compute the required size for the dump and then
fill the buffer with the data.
When we allocate the buffer, we test the STATUS_FW_ERROR
bit to check if the firmware is alive or not. This bit
can be changed during the course of the dump since it is
modified in the interrupt handler.
We hit a case where we allocate the buffer while the
firmware is sill working, and while we start to fill the
buffer, the firmware crashes. Then we test STATUS_FW_ERROR
again and decide to fill the buffer with data like the
FIFOs even if no room was allocated for this data in the
buffer. This means that we overflow the buffer that was
allocated leading to memory corruption.
To fix this, test the STATUS_FW_ERROR bit only once and
rely on local variables to check if we should dump fifos
or other firmware components.
Fixes: 04fd2c28226f ("iwlwifi: mvm: add rxf and txf to dump data")
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Alexei's patch, assumed that all versions of "struct iwl_error_event_table"
are the same, but there are really different versions in different files.
Rather than trying to fix this, or splitting the tracepoint, or anything of
the sort, just remove it entirely - turns out that nobody really uses it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We already report the RU offset, so we'd better also
report that we know the value.
Fixes: e5721e3f770f ("iwlwifi: mvm: add radiotap data for HE")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Check the actual bit (mask) in Rx notification rate_n_flags.
Signed-off-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Cleanup of the debug flow by moving several flows to separate
functions to increase readability. Three functions were created:
1. iwl_fw_get_prph_len - returns the size needed for periphery dump.
2. iwl_fw_dump_mem for - executes the memory dumping flow.
3. iwl_trans_get_fw_monitor_len - returns the size needed for monitor dump.
Signed-off-by: Shahar S Matityahu <shahar.s.matityahu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no value in having an anonymous struct for holding
a few fields, remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In new devices, access to periphery is forbidden. Send instead
host command to start and stop debugging.
Memory allocation is written in context info, but in case we
need to update it there is a dedicated command. Add definitions,
currently unused, of the new command.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Move the restart FW debug code to a function. This avoids code
duplication and lays the infra to support the new start and stop
host commands in some future devices.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The SP length in the ADD_STA command is an actual number of
frames, and not the SP len as it appears in the WME IE.
Fix that comment. The actual code is fine.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Commit b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
introduced a requirement that Makefiles more than one level below the
selftests directory need to define top_srcdir, but it didn't update
any of the powerpc Makefiles.
This broke building all the powerpc selftests with eg:
make[1]: Entering directory '/src/linux/tools/testing/selftests/powerpc'
BUILD_TARGET=/src/linux/tools/testing/selftests/powerpc/alignment; mkdir -p $BUILD_TARGET; make OUTPUT=$BUILD_TARGET -k -C alignment all
make[2]: Entering directory '/src/linux/tools/testing/selftests/powerpc/alignment'
../../lib.mk:20: ../../../../scripts/subarch.include: No such file or directory
make[2]: *** No rule to make target '../../../../scripts/subarch.include'.
make[2]: Failed to remake makefile '../../../../scripts/subarch.include'.
Makefile:38: recipe for target 'alignment' failed
Fix it by setting top_srcdir in the affected Makefiles.
Fixes: b2d35fa5fc80 ("selftests: add headers_install to lib.mk")
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
into drm-fixes
Just a few fixes for 4.19:
- Couple of suspend/resume fixes
- Fix EDID emulation with DC
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927155418.2813-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- Revert adding device-link to panels
- Don't leak fences in drm/syncobj
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Sean Paul <sean@poorly.run>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927152712.GA53076@art_vandelay
|
|
Jason writes:
"Second RDMA rc pull request
- Fix a long standing race bug when destroying comp_event file descriptors
- srp, hfi1, bnxt_re: Various driver crashes from missing validation
and other cases
- Fixes for regressions in patches merged this window in the gid
cache, devx, ucma and uapi."
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/core: Set right entry state before releasing reference
IB/mlx5: Destroy the DEVX object upon error flow
IB/uverbs: Free uapi on destroy
RDMA/bnxt_re: Fix system crash during RDMA resource initialization
IB/hfi1: Fix destroy_qp hang after a link down
IB/hfi1: Fix context recovery when PBC has an UnsupportedVL
IB/hfi1: Invalid user input can result in crash
IB/hfi1: Fix SL array bounds check
RDMA/uverbs: Fix validity check for modify QP
IB/srp: Avoid that sg_reset -d ${srp_device} triggers an infinite loop
ucma: fix a use-after-free in ucma_resolve_ip()
RDMA/uverbs: Atomically flush and mark closed the comp event queue
cxgb4: fix abort_req_rss6 struct
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs
Jan writes:
"an ext2 patch fixing fsync(2) for DAX mounts."
* tag 'for_v4.19-rc6' of git://git.kernel.org/pub/scm/linux/kernel/git/jack/linux-fs:
ext2, dax: set ext2_dax_aops for dax files
|
|
trace_block_unplug() takes true for explicit unplugs and false for
implicit unplugs. schedule() unplugs are implicit and should be
reported as timer unplugs. While correct in the legacy code, this has
been inverted in blk-mq since 4.11.
Cc: stable@vger.kernel.org
Fixes: bd166ef183c2 ("blk-mq-sched: add framework for MQ capable IO schedulers")
Reviewed-by: Omar Sandoval <osandov@fb.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
On x86-64, the parametrized selftest code for rseq crashes with a
segmentation fault when compiled with -fpie. This happens when the
param_test binary is loaded at an address beyond 32-bit on x86-64.
The issue is caused by use of a 32-bit register to hold the address
of the loop counter variable.
Fix this by using a 64-bit register to calculate the address of the
loop counter variables as an offset from rip.
Signed-off-by: Mathieu Desnoyers <mathieu.desnoyers@efficios.com>
Acked-by: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: <stable@vger.kernel.org> # v4.18
Cc: Shuah Khan <shuah@kernel.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Joel Fernandes <joelaf@google.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Watson <davejwatson@fb.com>
Cc: Will Deacon <will.deacon@arm.com>
Cc: Andi Kleen <andi@firstfloor.org>
Cc: linux-kselftest@vger.kernel.org
Cc: "H . Peter Anvin" <hpa@zytor.com>
Cc: Chris Lameter <cl@linux.com>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Michael Kerrisk <mtk.manpages@gmail.com>
Cc: "Paul E . McKenney" <paulmck@linux.vnet.ibm.com>
Cc: Paul Turner <pjt@google.com>
Cc: Boqun Feng <boqun.feng@gmail.com>
Cc: Josh Triplett <josh@joshtriplett.org>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Ben Maurer <bmaurer@fb.com>
Cc: Andy Lutomirski <luto@amacapital.net>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Shuah Khan (Samsung OSG) <shuah@kernel.org>
|
|
.max_tfd_queue_size was ommited for 1000 card serries leading to oops in
swiotlb.
Fixes: 7b3e42ea2ead ("iwlwifi: support multiple tfd queue max sizes for different devices")
Tested-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When dax_lock_mapping_entry() has to sleep to obtain entry lock, it will
fail to unlock mapping->i_pages spinlock and thus immediately deadlock
against itself when retrying to grab the entry lock again. Fix the
problem by unlocking mapping->i_pages before retrying.
Fixes: c2a7d2a11552 ("filesystem-dax: Introduce dax_lock_mapping_entry()")
Reported-by: Barret Rhoden <brho@google.com>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
Commit
1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
can occasionally cause system resets when kexec-ing a second kernel even
if SEV is not active.
That's because get_sev_encryption_bit() uses 32-bit rIP-relative
addressing to read the value of enc_bit - a variable which caches a
previously detected encryption bit position - but kexec may allocate
the early boot code to a higher location, beyond the 32-bit addressing
limit.
In this case, garbage will be read and get_sev_encryption_bit() will
return the wrong value, leading to accessing memory with the wrong
encryption setting.
Therefore, remove enc_bit, and thus get rid of the need to do 32-bit
rIP-relative addressing in the first place.
[ bp: massage commit message heavily. ]
Fixes: 1958b5fc4010 ("x86/boot: Add early boot support when running with SEV active")
Suggested-by: Borislav Petkov <bp@suse.de>
Signed-off-by: Kairui Song <kasong@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Tom Lendacky <thomas.lendacky@amd.com>
Cc: linux-kernel@vger.kernel.org
Cc: tglx@linutronix.de
Cc: mingo@redhat.com
Cc: hpa@zytor.com
Cc: brijesh.singh@amd.com
Cc: kexec@lists.infradead.org
Cc: dyoung@redhat.com
Cc: bhe@redhat.com
Cc: ghook@redhat.com
Link: https://lkml.kernel.org/r/20180927123845.32052-1-kasong@redhat.com
|
|
After write SSD completed, bcache schedules journal_write work to
system_wq, which is a public workqueue in system, without WQ_MEM_RECLAIM
flag. system_wq is also a bound wq, and there may be no idle kworker on
current processor. Creating a new kworker may unfortunately need to
reclaim memory first, by shrinking cache and slab used by vfs, which
depends on bcache device. That's a deadlock.
This patch create a new workqueue for journal_write with WQ_MEM_RECLAIM
flag. It's rescuer thread will work to avoid the deadlock.
Signed-off-by: Guoju Fang <fangguoju@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
rx_mini_pending was set to an incorrect value. This was causing EINVAL to
always be returned to 'ethtool -G'. The driver does not support mini or
jumbo rings so the respective settings should be zero.
Also, change the valid range of the number of descriptors in the rings to
make the code simpler and easier for users to understand (this removes the
valid settings of 8 and 16). Add a system log message indicating when the
number is rounded-up from what the user specifies with the 'ethtool -G'
command (i.e. when it is not a multiple of 32), and update the log message
when a user-provided value is out of range to also indicate the stride.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch makes a couple of changes in the way the driver uses the
"get capabilities" command.
1. Get device capabilities in addition to function capabilities
2. Align to latest spec by using cap_count to determine size of the
buffer in case of length error.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The combination of defined constants are used to present the
state of IRQ so the magic numbers has been replaced.
This is a simple coding style change which should have no impact on
runtime code execution.
Signed-off-by: Xue Liu <liuxuenetmail@gmail.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
Query the Tx scheduler tree node information from FW before adding it to
the driver's software database. This will keep the node information current
in driver.
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Previously the comment stated that VSI lists should be used when a
second VSI becomes a subscriber to the "VLAN address". VSI lists
are always used for VLAN membership, so replace "VLAN address" with
"MAC address". Also note that VLAN(s) always use VSI list rules.
Signed-off-by: Brett Creeley <brett.creeley@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and
MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a
firmware version is newer than expected. This is currently tested by
comparing each field separately. Thus, we compare the branch field
against the MAX_FW_API_VER_BRANCH, and so forth.
This means that currently, if we suppose that the max firmware version
is defined as 0.2.1, i.e.
Then firmware 0.1.3 will fail to load. This is because the minor version
3 is greater than the max minor version 1.
This is not intuitive, because of the notion that increasing the major
firmware version to 2 should mean any firmware version with a major
version is less than 2 should be considered older than 2...
In order to allow both 0.2.1 and 0.1.3 to load, you would have to define
the "max" firmware version as 0.2.3.. It is possible that such
a firmware version doesn't even exist yet!
Fix this by replacing the current logic with an updated check that
behaves as follows:
First, we check the major version. If it is greater than the expected
version, then we prevent driver load. Additionally, a warning message is
logged to indicate to the system administrator that they need to update
their driver. This is now the only case where the driver will refuse to
load.
Second, if the major version is less than the expected version, we log
an information message indicating the NVM should be updated.
Third, if the major version is exact, we'll then check the minor
version. If the minor version is more than two versions less than
expected, we log an information message indicating the NVM should be
updated. If it is more than two versions greater than the expected
version, we log an information message that the driver should be
updated.
To support this, the ice_aq_ver_check function needs its signature
updated to pass the HW structure. Since we now pass this structure,
there is no need to pass the firmware API versions separately.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Update branding strings and remove device ids 0x1594 and 0x1595.
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Direct assignment is preferred over a memcpy()
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
[Why]
EDID emulation didn't work properly for linux, as we stop programming
if nothing is connected physically.
[How]
We get a flag from DRM when we want to do edid emulation. We check if
this flag is true and nothing is connected physically, if so we only
program the front end using VIRTUAL_SIGNAL.
Signed-off-by: Bhawanpreet Lakha <Bhawanpreet.Lakha@amd.com>
Reviewed-by: Harry Wentland <Harry.Wentland@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
[Why]
There have been a few reports of Vega10 display remaining blank
after S3 resume. The regression is caused by workaround for mode
change on Vega10 - skip set_bandwidth if stream count is 0.
As a result we skipped dispclk reset on suspend, thus on resume
we may skip the clock update assuming it hasn't been changed.
On some systems it causes display blank or 'out of range'.
[How]
Revert "drm/amd/display: Fix Vega10 black screen after mode change"
Verified that it hadn't cause mode change regression.
Signed-off-by: Roman Li <Roman.Li@amd.com>
Reviewed-by: Sun peng Li <Sunpeng.Li@amd.com>
Acked-by: Leo Li <sunpeng.li@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The vce cancel_delayed_work_sync never be called.
driver call the function in error path.
This caused the A+A suspend hang when runtime pm enebled.
As we will visit the smu in the idle queue. this will cause
smu hang because the dgpu has been suspend, and the dgpu also
will be waked up. As the smu has been hang, so the dgpu resume
will failed.
Reviewed-by: Christian König <christian.koenig@amd.com>
Reviewed-by: Feifei Xu <Feifei.Xu@amd.com>
Signed-off-by: Rex Zhu <Rex.Zhu@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
Cc: stable@vger.kernel.org
|
|
This reverts commit 0c08754b59da5557532d946599854e6df28edc22.
commit 0c08754b59da
("drm/panel: Add device_link from panel device to DRM device")
creates a circular dependency under these circumstances:
1. The panel depends on dsi-host because it is MIPI-DSI child
device.
2. dsi-host depends on the drm parent device (connector->dev->dev)
this should be allowed.
3. drm parent dev (connector->dev->dev) depends on the panel
after this patch.
This makes the dependency circular and while it appears it
does not affect any in-tree drivers (they do not seem to have
dsi hosts depending on the same parent device) this does not
seem right.
As noted in a response from Andrzej Hajda, the intent is
likely to make the panel dependent on the DRM device
(connector->dev) not its parent. But we have no way of
doing that since the DRM device doesn't contain any
struct device on its own (arguably it should).
Revert this until a proper approach is figured out.
Cc: Jyri Sarha <jsarha@ti.com>
Cc: Eric Anholt <eric@anholt.net>
Cc: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20180927124130.9102-1-linus.walleij@linaro.org
|
|
When shutting down the controlqs, we check if they are initialized
before we shut them down and destroy the lock. This is important, as it
prevents attempts to access the lock of an already shutdown queue.
Unfortunately, we checked rq.head and sq.head as the value to determine
if the queue was initialized. This doesn't work, because head is not
reset when the queue is shutdown. In some flows, the adminq will have
already been shut down prior to calling ice_shutdown_all_ctrlqs. This
can result in a crash due to attempting to access the already destroyed
mutex.
Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq
and ice_shutdown_rq already indicate that this is the value we should be
using to determine of the queue was initialized.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
https://git.linaro.org/people/daniel.lezcano/linux into timers/urgent
Pull another fix from Daniel Lezcano, which felt through the cracks:
- Fix a potential memory leak reported by smatch in the atmel timer driver
|
|
Commit a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
added support for purging persistent grants when they are not in use. As
part of the purge, the grants were removed from the grant buffer, This
eventually causes the buffer to become empty, with BUG_ON triggered in
get_free_grant(). This can be observed even on an idle system, within
20-30 minutes.
We should keep the grants in the buffer when purging, and only free the
grant ref.
Fixes: a46b53672b2c ("xen/blkfront: cleanup stale persistent grants")
Reviewed-by: Juergen Gross <jgross@suse.com>
Signed-off-by: Boris Ostrovsky <boris.ostrovsky@oracle.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
rxrpc_find_connection_rcu() initialises variable k twice with the same
information. Remove one of the initialisations.
Signed-off-by: David Howells <dhowells@redhat.com>
|
|
debugfs_remove has taken the IS_ERR into account. Just
remove the unnecessary condition.
Signed-off-by: zhong jiang <zhongjiang@huawei.com>
Signed-off-by: Stefan Schmidt <stefan@datenfreihafen.org>
|
|
simple_strtol and simple_strtoul are obsolete, both place
use kstrtouint instead.
V2: fix error tmp += tn
V3: fix compile error
Signed-off-by: Ding Xiang <dingxiang@cmss.chinamobile.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
