| Age | Commit message (Collapse) | Author |
|---|
|
observed sometimes data is coming with unaligned address from kernel
BT stack. If unaligned address is passed, some data in payload is
stripped when packet is loading to firmware and this results, BT
connection timeout is happening.
sh# hciconfig hci0 up
Can't init device hci0: hci0 command 0x0c03 tx timeout
Fixed this by moving the data to aligned address.
Signed-off-by: Sanjay Kumar Konduri <sanjay.konduri@redpinesignals.com>
Signed-off-by: Siva Rebbagondla <siva.rebbagondla@redpinesignals.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
If the remote is not able to fully utilize the MPS choosen recalculate
the credits based on the actual amount it is sending that way it can
still send packets of MTU size without credits dropping to 0.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Give enough rx credits for a full packet instead of using an arbitrary
number which may not be enough depending on the MTU and MPS which can
cause interruptions while waiting for more credits, also remove
debugfs entry for l2cap_le_max_credits.
With these changes the credits are restored after each SDU is received
instead of using fixed threshold, this way it is garanteed that there
will always be enough credits to send a packet without waiting more
credits to arrive.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This ensures the MPS can fit in a single HCI fragment so each
segment don't have to be reassembled at HCI level, in addition to
that also remove the debugfs entry to configure the MPS.
Signed-off-by: Luiz Augusto von Dentz <luiz.von.dentz@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch adds the device ID for the AMPAK AP6335 combo module used
in the 1st generation WeTek Hub Android/LibreELEC HTPC box. The WiFI
chip identifies itself as BCM4339, while Bluetooth identifies itself
as BCM4335 (rev C0):
```
[ 4.864248] Bluetooth: hci0: BCM: chip id 86
[ 4.866388] Bluetooth: hci0: BCM: features 0x2f
[ 4.889317] Bluetooth: hci0: BCM4335C0
[ 4.889332] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0000
[ 9.778383] Bluetooth: hci0: BCM4335C0 (003.001.009) build 0268
```
Output from hciconfig:
```
hci0: Type: Primary Bus: UART
BD Address: 43:39:00:00:1F:AC ACL MTU: 1021:8 SCO MTU: 64:1
UP RUNNING
RX bytes:7567 acl:234 sco:0 events:386 errors:0
TX bytes:53844 acl:77 sco:0 commands:304 errors:0
Features: 0xbf 0xfe 0xcf 0xfe 0xdb 0xff 0x7b 0x87
Packet type: DM1 DM3 DM5 DH1 DH3 DH5 HV1 HV2 HV3
Link policy: RSWITCH SNIFF
Link mode: SLAVE ACCEPT
Name: 'HUB'
Class: 0x0c0000
Service Classes: Rendering, Capturing
Device Class: Miscellaneous,
HCI Version: 4.0 (0x6) Revision: 0x10c
LMP Version: 4.0 (0x6) Subversion: 0x6109
Manufacturer: Broadcom Corporation (15)
```
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This device is included in the RTL8822CU combination wifi and BT part,
as well as the BT part of the RTL8822CE.
The necessary firmware has been submitted to the linux-firmware
project.
Signed-off-by: Alex Lu <alex_lu@realsil.com.cn>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Fixed error in space required before paranthesis
in drivers/bluetooth/hci_serdev.c
Signed-off-by: Jagdish Tirumala <t.jag587@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Add the definitions for adding entries to the LE resolve list and
removing entries from the LE resolve list. When the LE resolve list
gets changed via HCI commands make sure that the internal storage of
the resolve list entries gets updated.
Signed-off-by: Ankit Navik <ankit.p.navik@intel.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
This patch enables power off support for hci down and power on support
for hci up. As wcn3990 power sources are ignited by regulators, we will
turn off them during hci down, i.e. an complete power off of wcn3990.
So while hci up, will call vendor setup which will turn on the regulators,
requests BT chip version and download the firmware.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Intel "new" controllers can do both LE scan and BR/EDR inquiry at once.
Signed-off-by: Justin TerAvest <teravest@google.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Don't populate the array extension_sig on the stack but instead make it
static. Makes the object code smaller by 75 bytes:
Before:
text data bss dec hex filename
14325 4920 0 19245 4b2d drivers/bluetooth/btrtl.o
After:
text data bss dec hex filename
14186 4984 0 19170 4ae2 drivers/bluetooth/btrtl.o
(gcc version 8.2.0 x86_64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The smatch utility reports a possible leak:
smatch warnings:
drivers/clocksource/timer-atmel-pit.c:183 at91sam926x_pit_dt_init() warn: possible memory leak of 'data'
Ensure data is freed before exiting with an error.
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: stable@vger.kernel.org
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
This will help to check the status of protocol while dequeuing an
skb packet. In some instaces we will end up kernel crash,
where proto close is called and we trying to dequeue an packet.
[ 500.142902] [<ffffff80080f9ce4>] do_raw_spin_lock+0x1c/0xe0
[ 500.148643] [<ffffff80088f1c7c>] _raw_spin_lock_irqsave+0x38/0x48
[ 500.154917] [<ffffff8008780ce8>] skb_dequeue+0x28/0x84
[ 500.160209] [<ffffff8000ad6f48>] 0xffffff8000ad6f48
[ 500.165230] [<ffffff8000ad6610>] 0xffffff8000ad6610
[ 500.170257] [<ffffff80080c7ce8>] process_one_work+0x238/0x3e4
[ 500.176174] [<ffffff80080c8330>] worker_thread+0x2bc/0x3d4
[ 500.181821] [<ffffff80080cdabc>] kthread+0x138/0x140
[ 500.186945] [<ffffff80080844e0>] ret_from_fork+0x10/0x18
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Clearing HCI_UART_PROTO_READY will avoid usage of proto function pointers
before running the proto close function pointer. There is chance of kernel
crash, due to usage of non proto close function pointers after proto close.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
When flag KASAN is set, we are seeing an following crash while removing
hci_uart module.
[ 50.589909] Unable to handle kernel paging request at virtual address 6b6b6b6b6b6b73
[ 50.597902] Mem abort info:
[ 50.600846] Exception class = DABT (current EL), IL = 32 bits
[ 50.606959] SET = 0, FnV = 0
[ 50.610142] EA = 0, S1PTW = 0
[ 50.613396] Data abort info:
[ 50.616401] ISV = 0, ISS = 0x00000004
[ 50.620373] CM = 0, WnR = 0
[ 50.623466] [006b6b6b6b6b6b73] address between user and kernel address ranges
[ 50.630818] Internal error: Oops: 96000004 [#1] PREEMPT SMP
[ 50.671670] PC is at qca_power_shutdown+0x28/0x100 [hci_uart]
[ 50.677593] LR is at qca_close+0x74/0xb0 [hci_uart]
[ 50.775689] Process rmmod (pid: 2144, stack limit = 0xffffff801ba90000)
[ 50.782493] Call trace:
[ 50.872150] [<ffffff8000c3c81c>] qca_power_shutdown+0x28/0x100 [hci_uart]
[ 50.879138] [<ffffff8000c3c968>] qca_close+0x74/0xb0 [hci_uart]
[ 50.885238] [<ffffff8000c3a71c>] hci_uart_unregister_device+0x44/0x50 [hci_uart]
[ 50.892846] [<ffffff8000c3c9f4>] qca_serdev_remove+0x50/0x5c [hci_uart]
[ 50.899654] [<ffffff800844f630>] serdev_drv_remove+0x28/0x38
[ 50.905489] [<ffffff800850fc44>] device_release_driver_internal+0x140/0x1e4
[ 50.912653] [<ffffff800850fd94>] driver_detach+0x78/0x84
[ 50.918121] [<ffffff800850edac>] bus_remove_driver+0x80/0xa8
[ 50.923942] [<ffffff80085107dc>] driver_unregister+0x4c/0x58
[ 50.929768] [<ffffff8000c3ca8c>] qca_deinit+0x24/0x598 [hci_uart]
[ 50.936045] [<ffffff8000c3ca10>] hci_uart_exit+0x10/0x48 [hci_uart]
[ 50.942495] [<ffffff8008136630>] SyS_delete_module+0x17c/0x224
This crash is due to dereference of hdev, after freeing it.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Removed serdev_device_open/close functions from qca_open/close as
they are called in hci_uart_register_device() and
hci_uart_unregister_device() functions.
Signed-off-by: Balakrishna Godavarthi <bgodavar@codeaurora.org>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
The barriers are unneeded; wait_woken() and woken_wake_function()
already provide us with the required synchronization: remove them
and document that we're relying on the (implicit) synchronization
provided by wait_woken() and woken_wake_function().
Signed-off-by: Andrea Parri <andrea.parri@amarulasolutions.com>
Reviewed-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
|
|
Use array_index_nospec() to sanitize i with respect to speculation.
Note that the user doesn't control i directly, but can make it out
of bounds by not finding a threshold in the array.
Signed-off-by: Masashi Honma <masashi.honma@gmail.com>
[add note about user control, as explained by Masashi]
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
|
|
(fix documentation and sysctl access to treat it as such)
Tested:
# zcat /proc/config.gz | egrep ^CONFIG_HZ
CONFIG_HZ_1000=y
CONFIG_HZ=1000
# echo $[(1<<32)/1000 + 1] | tee /proc/sys/net/ipv4/tcp_probe_interval
4294968
tee: /proc/sys/net/ipv4/tcp_probe_interval: Invalid argument
# echo $[(1<<32)/1000] | tee /proc/sys/net/ipv4/tcp_probe_interval
4294967
# echo 0 | tee /proc/sys/net/ipv4/tcp_probe_interval
# echo -1 | tee /proc/sys/net/ipv4/tcp_probe_interval
-1
tee: /proc/sys/net/ipv4/tcp_probe_interval: Invalid argument
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current netpoll implementation in the bnxt_en driver has problems
that may miss TX completion events. bnxt_poll_work() in effect is
only handling at most 1 TX packet before exiting. In addition,
there may be in flight TX completions that ->poll() may miss even
after we fix bnxt_poll_work() to handle all visible TX completions.
netpoll may not call ->poll() again and HW may not generate IRQ
because the driver does not ARM the IRQ when the budget (0 for netpoll)
is reached.
We fix it by handling all TX completions and to always ARM the IRQ
when we exit ->poll() with 0 budget.
Also, the logic to ACK the completion ring in case it is almost filled
with TX completions need to be adjusted to take care of the 0 budget
case, as discussed with Eric Dumazet <edumazet@google.com>
Reported-by: Song Liu <songliubraving@fb.com>
Reviewed-by: Song Liu <songliubraving@fb.com>
Tested-by: Song Liu <songliubraving@fb.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(the parameters in question are mark and flow_flags)
Reviewed-by: David Ahern <dsahern@gmail.com>
Signed-off-by: Maciej Żenczykowski <maze@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When add vxlan ttl inherit support, I forgot to fill it when dump
vlxan info. Fix it now.
Fixes: 72f6d71e491e6 ("vxlan: add ttl inherit support")
Signed-off-by: Hangbin Liu <liuhangbin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta controller can handle speeds up to 2500Mbps on the SGMII
interface. This relies on serdes configuration, the lane must be
configured at 3.125Gbps and we can't use in-band autoneg at that speed.
The main issue when supporting that speed on this particular controller
is that the link partner can send ethernet frames with a shortened
preamble, which if not explicitly enabled in the controller will cause
unexpected behaviours.
This was tested on Armada 385, with the comphy configuration done in
bootloader.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Tonghao Zhang says:
====================
net: vhost: improve performance when enable busyloop
This patches improve the guest receive performance.
On the handle_tx side, we poll the sock receive queue
at the same time. handle_rx do that in the same way.
For more performance report, see patch 4
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch improves the guest receive performance.
On the handle_tx side, we poll the sock receive queue at the
same time. handle_rx do that in the same way.
We set the poll-us=100us and use the netperf to test throughput
and mean latency. When running the tests, the vhost-net kthread
of that VM, is alway 100% CPU. The commands are shown as below.
Rx performance is greatly improved by this patch. There is not
notable performance change on tx with this series though. This
patch is useful for bi-directional traffic.
netperf -H IP -t TCP_STREAM -l 20 -- -O "THROUGHPUT, THROUGHPUT_UNITS, MEAN_LATENCY"
Topology:
[Host] ->linux bridge -> tap vhost-net ->[Guest]
TCP_STREAM:
* Without the patch: 19842.95 Mbps, 6.50 us mean latency
* With the patch: 37598.20 Mbps, 3.43 us mean latency
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Factor out generic busy polling logic and will be
used for in tx path in the next patch. And with the patch,
qemu can set differently the busyloop_timeout for rx queue.
To avoid duplicate codes, introduce the helper functions:
* sock_has_rx_data(changed from sk_has_rx_data)
* vhost_net_busy_poll_try_queue
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the VHOST_NET_VQ_XXX as a subclass for mutex_lock_nested.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch changes the way that lock all vqs
at the same, to lock them one by one. It will
be used for next patch to avoid the deadlock.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Acked-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A HWMON device is only registered is the SFP module supports the
diagnostic page and is complient to SFF8472. Don't unconditionally
unregister the hwmon device when the SFP module is remove, otherwise
we access data structures which don't exist.
Reported-by: Florian Fainelli <f.fainelli@gmail.com>
Fixes: 1323061a018a ("net: phy: sfp: Add HWMON support for module sensors")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1713:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV4;
~ ^~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_iwarp.c:1733:25: warning: implicit
conversion from enumeration type 'enum tcp_ip_version' to different
enumeration type 'enum qed_tcp_ip_version' [-Wenum-conversion]
cm_info->ip_version = TCP_IPV6;
~ ^~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, qed_tcp_ip_version:
TCP_IPV4 = QED_TCP_IPV4 = 0
TCP_IPV6 = QED_TCP_IPV6 = 1
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when a constant is used in a boolean context as it thinks a
bitwise operation may have been intended.
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: warning: use of logical
'&&' with constant operand [-Wconstant-logical-operand]
if (!p_iov->b_pre_fp_hsi &&
^
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: use '&' for a
bitwise operation
if (!p_iov->b_pre_fp_hsi &&
^~
&
drivers/net/ethernet/qlogic/qed/qed_vf.c:415:27: note: remove constant
to silence this warning
if (!p_iov->b_pre_fp_hsi &&
~^~
1 warning generated.
This has been here since commit 1fe614d10f45 ("qed: Relax VF firmware
requirements") and I am not entirely sure why since 0 isn't a special
case. Just remove the statement causing Clang to warn since it isn't
required.
Link: https://github.com/ClangBuiltLinux/linux/issues/126
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Syzkaller reported this on a slightly older kernel but it's still
applicable to the current kernel -
======================================================
WARNING: possible circular locking dependency detected
4.18.0-next-20180823+ #46 Not tainted
------------------------------------------------------
syz-executor4/26841 is trying to acquire lock:
00000000dd41ef48 ((wq_completion)bond_dev->name){+.+.}, at: flush_workqueue+0x2db/0x1e10 kernel/workqueue.c:2652
but task is already holding lock:
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnl_lock net/core/rtnetlink.c:77 [inline]
00000000768ab431 (rtnl_mutex){+.+.}, at: rtnetlink_rcv_msg+0x412/0xc30 net/core/rtnetlink.c:4708
which lock already depends on the new lock.
the existing dependency chain (in reverse order) is:
-> #2 (rtnl_mutex){+.+.}:
__mutex_lock_common kernel/locking/mutex.c:925 [inline]
__mutex_lock+0x171/0x1700 kernel/locking/mutex.c:1073
mutex_lock_nested+0x16/0x20 kernel/locking/mutex.c:1088
rtnl_lock+0x17/0x20 net/core/rtnetlink.c:77
bond_netdev_notify drivers/net/bonding/bond_main.c:1310 [inline]
bond_netdev_notify_work+0x44/0xd0 drivers/net/bonding/bond_main.c:1320
process_one_work+0xc73/0x1aa0 kernel/workqueue.c:2153
worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
kthread+0x35a/0x420 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
-> #1 ((work_completion)(&(&nnw->work)->work)){+.+.}:
process_one_work+0xc0b/0x1aa0 kernel/workqueue.c:2129
worker_thread+0x189/0x13c0 kernel/workqueue.c:2296
kthread+0x35a/0x420 kernel/kthread.c:246
ret_from_fork+0x3a/0x50 arch/x86/entry/entry_64.S:415
-> #0 ((wq_completion)bond_dev->name){+.+.}:
lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
__alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
register_netdevice+0x337/0x1100 net/core/dev.c:8410
bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:632
___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
__sys_sendmsg+0x11d/0x290 net/socket.c:2153
__do_sys_sendmsg net/socket.c:2162 [inline]
__se_sys_sendmsg net/socket.c:2160 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
other info that might help us debug this:
Chain exists of:
(wq_completion)bond_dev->name --> (work_completion)(&(&nnw->work)->work) --> rtnl_mutex
Possible unsafe locking scenario:
CPU0 CPU1
---- ----
lock(rtnl_mutex);
lock((work_completion)(&(&nnw->work)->work));
lock(rtnl_mutex);
lock((wq_completion)bond_dev->name);
*** DEADLOCK ***
1 lock held by syz-executor4/26841:
stack backtrace:
CPU: 1 PID: 26841 Comm: syz-executor4 Not tainted 4.18.0-next-20180823+ #46
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS Google 01/01/2011
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0x1c9/0x2b4 lib/dump_stack.c:113
print_circular_bug.isra.34.cold.55+0x1bd/0x27d kernel/locking/lockdep.c:1222
check_prev_add kernel/locking/lockdep.c:1862 [inline]
check_prevs_add kernel/locking/lockdep.c:1975 [inline]
validate_chain kernel/locking/lockdep.c:2416 [inline]
__lock_acquire+0x3449/0x5020 kernel/locking/lockdep.c:3412
lock_acquire+0x1e4/0x4f0 kernel/locking/lockdep.c:3901
flush_workqueue+0x30a/0x1e10 kernel/workqueue.c:2655
drain_workqueue+0x2a9/0x640 kernel/workqueue.c:2820
destroy_workqueue+0xc6/0x9d0 kernel/workqueue.c:4155
__alloc_workqueue_key+0xef9/0x1190 kernel/workqueue.c:4138
bond_init+0x269/0x940 drivers/net/bonding/bond_main.c:4734
register_netdevice+0x337/0x1100 net/core/dev.c:8410
bond_newlink+0x49/0xa0 drivers/net/bonding/bond_netlink.c:453
rtnl_newlink+0xef4/0x1d50 net/core/rtnetlink.c:3099
rtnetlink_rcv_msg+0x46e/0xc30 net/core/rtnetlink.c:4711
netlink_rcv_skb+0x172/0x440 net/netlink/af_netlink.c:2454
rtnetlink_rcv+0x1c/0x20 net/core/rtnetlink.c:4729
netlink_unicast_kernel net/netlink/af_netlink.c:1317 [inline]
netlink_unicast+0x5a0/0x760 net/netlink/af_netlink.c:1343
netlink_sendmsg+0xa18/0xfc0 net/netlink/af_netlink.c:1908
sock_sendmsg_nosec net/socket.c:622 [inline]
sock_sendmsg+0xd5/0x120 net/socket.c:632
___sys_sendmsg+0x7fd/0x930 net/socket.c:2115
__sys_sendmsg+0x11d/0x290 net/socket.c:2153
__do_sys_sendmsg net/socket.c:2162 [inline]
__se_sys_sendmsg net/socket.c:2160 [inline]
__x64_sys_sendmsg+0x78/0xb0 net/socket.c:2160
do_syscall_64+0x1b9/0x820 arch/x86/entry/common.c:290
entry_SYSCALL_64_after_hwframe+0x49/0xbe
RIP: 0033:0x457089
Code: fd b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00 00 66 90 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 0f 83 cb b4 fb ff c3 66 2e 0f 1f 84 00 00 00 00
RSP: 002b:00007f2df20a5c78 EFLAGS: 00000246 ORIG_RAX: 000000000000002e
RAX: ffffffffffffffda RBX: 00007f2df20a66d4 RCX: 0000000000457089
RDX: 0000000000000000 RSI: 0000000020000180 RDI: 0000000000000003
RBP: 0000000000930140 R08: 0000000000000000 R09: 0000000000000000
R10: 0000000000000000 R11: 0000000000000246 R12: 00000000ffffffff
R13: 00000000004d40b8 R14: 00000000004c8ad8 R15: 0000000000000001
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit b89f04c61efe ("bonding: deliver link-local packets with
skb->dev set to link that packets arrived on") changed the behavior
of how link-local-multicast packets are processed. The change in
the behavior broke some legacy use cases where these packets are
expected to arrive on bonding master device also.
This patch passes the packet to the stack with the link it arrived
on as well as passes to the bonding-master device to preserve the
legacy use case.
Fixes: b89f04c61efe ("bonding: deliver link-local packets with skb->dev set to link that packets arrived on")
Reported-by: Michal Soltys <soltys@ziu.info>
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_roce.c:153:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = ROCE_V2_IPV6;
~ ^~~~~~~~~~~~
drivers/net/ethernet/qlogic/qed/qed_roce.c:156:12: warning: implicit
conversion from enumeration type 'enum roce_mode' to different
enumeration type 'enum roce_flavor' [-Wenum-conversion]
flavor = MAX_ROCE_MODE;
~ ^~~~~~~~~~~~~
2 warnings generated.
Use the appropriate values from the expected type, roce_flavor:
ROCE_V2_IPV6 = RROCE_IPV6 = 2
MAX_ROCE_MODE = MAX_ROCE_FLAVOR = 3
While we're add it, ditch the local variable flavor, we can just return
the value directly from the switch statement.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang complains when one enumerated type is implicitly converted to
another.
drivers/net/ethernet/qlogic/qed/qed_vf.c:686:6: warning: implicit
conversion from enumeration type 'enum qed_tunn_mode' to different
enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
QED_MODE_L2GENEVE_TUNN,
^~~~~~~~~~~~~~~~~~~~~~
Update mask's parameter to expect qed_tunn_mode, which is what was
intended.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Clang warns when one enumerated type is implicitly converted to another.
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:163:25: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->vxlan.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:165:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:167:26: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_gre.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:169:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->l2_geneve.tun_cls = type;
~ ^~~~
drivers/net/ethernet/qlogic/qed/qed_sp_commands.c:171:29: warning:
implicit conversion from enumeration type 'enum tunnel_clss' to
different enumeration type 'enum qed_tunn_clss' [-Wenum-conversion]
p_tun->ip_geneve.tun_cls = type;
~ ^~~~
5 warnings generated.
Avoid this by changing type to an int.
Link: https://github.com/ClangBuiltLinux/linux/issues/125
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in ms_to_errno array of error messages
and remove confusing "not" from the error text since the error code
refers to an uninitialized error code.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in DP_VERBOSE message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After sk_state exposed, we can get in which state this retransmission
occurs. That could give us more detail for dignostic.
For example, if this retransmission occurs in SYN_SENT state, it may
also indicates that the syn packet may be dropped on the remote peer due
to syn backlog queue full and then we could check the remote peer.
BTW,SYNACK retransmission is traced in tcp_retransmit_synack tracepoint.
Signed-off-by: Yafang Shao <laoar.shao@gmail.com>
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Heiner Kallweit says:
====================
net: phy: fix WoL handling when suspending the PHY
phy_suspend doesn't always recognize that WoL is enabled and therefore
suspends the PHY when it should not. First idea to address the issue
was to reuse checks used in mdio_bus_phy_may_suspend which check
whether relevant devices are wakeup-enabled.
Florian raised some concerns because drivers may enable wakeup even if
WoL isn't enabled (e.g. certain USB network drivers).
The new approach focuses on reducing the risk to break existing stuff.
We add a flag wol_enabled to struct net_device which is set in
ethtool_set_wol(). Then this flag is checked in phy_suspend().
This doesn't cover 100% of the cases yet (e.g. if WoL is enabled w/o
explicit configuration), but it covers the most relevant cases with
very little risk of regressions.
v2:
- Fix a typo
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Core of the problem is that phy_suspend() suspends the PHY when it
should not because of WoL. phy_suspend() checks for WoL already, but
this works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
This patch uses new member wol_enabled of struct net_device as
additional criteria in the check when not to suspend the PHY because
of WoL.
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add flag wol_enabled to struct net_device indicating whether
Wake-on-LAN is enabled. As first user phy_suspend() will use it to
decide whether PHY can be suspended or not.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit e0511f6c1ccdd153cf063764e93ac177a8553c5d.
I commited the wrong version of these changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Actually there's nothing wrong with the two changes marked as "Fixes",
they just revealed a problem which has been existing before.
After having switched r8169 to phylib it was reported that WoL from
shutdown doesn't work any longer (WoL from suspend isn't affected).
Reason is that during shutdown phy_disconnect()->phy_detach()->
phy_suspend() is called.
A similar issue occurs when the phylib state machine calls
phy_suspend() when handling state PHY_HALTED.
Core of the problem is that phy_suspend() suspends the PHY when it
should not due to WoL. phy_suspend() checks for WoL already, but this
works only if the PHY driver handles WoL (what is rarely the case).
Typically WoL is handled by the MAC driver.
phylib knows about this and handles it in mdio_bus_phy_may_suspend(),
but that's used only when suspending the system, not in other cases
like shutdown.
Therefore factor out the relevant check from
mdio_bus_phy_may_suspend() to a new function phy_may_suspend() and
use it in phy_suspend().
Last but not least change phy_detach() to call phy_suspend() before
attached_dev is set to NULL. phy_suspend() accesses attached_dev
when checking whether the MAC driver activated WoL.
Fixes: f1e911d5d0df ("r8169: add basic phylib support")
Fixes: e8cfd9d6c772 ("net: phy: call state machine synchronously in phy_stop")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The change to move metrics from the dst to rt6_info moved the call
to ip6_convert_metrics from ip6_route_add to ip6_route_info_create. In
doing so it makes the call in ip6_route_info_append redundant and
actually leaks the metrics installed as part of the ip6_route_info_create.
Remove the now unnecessary call.
Fixes: d4ead6b34b67f ("net/ipv6: move metrics from dst to rt6_info")
Signed-off-by: David Ahern <dsahern@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the deadline scheduler is used with a zoned block device, writes
to a zone will be dispatched one at a time. This causes the warning
message:
deadline: forced dispatching is broken (nr_sorted=X), please report this
to be displayed when switching to another elevator with the legacy I/O
path while write requests to a zone are being retained in the scheduler
queue.
Prevent this message from being displayed when executing
elv_drain_elevator() for a zoned block device. __blk_drain_queue() will
loop until all writes are dispatched and completed, resulting in the
desired elevator queue drain without extensive modifications to the
deadline code itself to handle forced-dispatch calls.
Signed-off-by: Damien Le Moal <damien.lemoal@wdc.com>
Fixes: 8dc8146f9c92 ("deadline-iosched: Introduce zone locking support")
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
into drm-fixes
Fix NV12 writeback and fix vblank reset.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Liviu Dudau <Liviu.Dudau@arm.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20180921112354.GR936@e110455-lin.cambridge.arm.com
|
|
into drm-fixes
one fix to get a proper DMA configuration in place for the etnaviv
virtual device. I'm sending this as a fix, as a dma-mapping change at
the ARC architecture side during the 4.19 cycle broke etnaviv on this
platform, which gets remedied with this patch, but it also enables
ARM64.
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Lucas Stach <l.stach@pengutronix.de>
Link: https://patchwork.freedesktop.org/patch/msgid/ea1f712bf09bf9439c6b092bf2c2bde7bb01cf5e.camel@pengutronix.de
|
|
The debounce value in device tree is in milliseconds but needs to be in
microseconds for mmc_gpiod_request_cd().
Fixes: bfd694d5e21c ("mmc: core: Add tunable delay before detecting card
after card is inserted")
Cc: Shawn Lin <shawn.lin@rock-chips.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
Cc: stable@vger.kernel.org # v4.18+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
