| Age | Commit message (Collapse) | Author |
|---|
|
Add pinctrl groups for both GPT input capture channels.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The reset pin to the port expander chip (MAX7310) is controlled by a gpio,
so define a reset-gpios property to control it. There are three MAX7310's
on the SabreAuto CPU card (max7310_[abc]), but all use the same pin for
their reset. Since all can't acquire the same pin, assign it to max7310_b,
that chip is needed by more functions (usb and adv7180).
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The sabreauto uses a steering pin to select between the SDA signal on
i2c3 bus, and a data-in pin for an SPI NOR chip. Use i2cmux to control
this steering pin. Idle state of the i2cmux selects SPI NOR. This is not
a classic way to use i2cmux, since one side of the mux selects something
other than an i2c bus, but it works and is probably the cleanest
solution. Note that if one thread is attempting to access SPI NOR while
another thread is accessing i2c3, the SPI NOR access will fail since the
i2cmux has selected the SDA pin rather than SPI NOR data-in. This couldn't
be avoided in any case, the board is not designed to allow concurrent
i2c3 and SPI NOR functions (and the default device-tree does not enable
SPI NOR anyway).
Devices hanging off i2c3 should now be defined under i2cmux, so
that the steering pin can be properly controlled to access those
devices. The port expanders (MAX7310) are thus moved into i2cmux.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enables the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
Until the OV5652 sensor module compatible with the SabreSD becomes
available for testing, the ov5642 node is currently disabled.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Adds the OV5642 parallel-bus sensor, and the OV5640 MIPI CSI-2 sensor.
Both hang off the same i2c2 bus, so they require different (and non-
default) i2c slave addresses.
The OV5642 connects to the parallel-bus mux input port on ipu1_csi0_mux.
The OV5640 connects to the input port on the MIPI CSI-2 receiver on
mipi_csi.
The OV5642 node is disabled temporarily while the subdev driver is
cleaned up and submitted later.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
There is a pin conflict with GPIO_6. This pin functions as a power
input pin to the OV5642 camera sensor, but ENET uses it as the h/w
workaround for erratum ERR006687, to wake-up the ARM cores on normal
RX and TX packet done events. So we need to remove the h/w workaround
to support the OV5642. The result is that the CPUidle driver will no
longer allow entering the deep idle states on the sabrelite.
This is a partial revert of
commit 6261c4c8f13e ("ARM: dts: imx6qdl-sabrelite: use GPIO_6 for FEC
interrupt.")
commit a28eeb43ee57 ("ARM: dts: imx6: tag boards that have the HW workaround
for ERR006687")
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the device tree graph connecting the input multiplexers
to the IPU CSIs and the MIPI-CSI2 gasket on i.MX6. The MIPI_IPU
multiplexers are added as children of the iomuxc-gpr syscon device node.
On i.MX6Q/D two two-input multiplexers in front of IPU1 CSI0 and IPU2
CSI1 allow to select between CSI0/1 parallel input pads and the MIPI
CSI-2 virtual channels 0/3.
On i.MX6DL/S two five-input multiplexers in front of IPU1 CSI0 and IPU1
CSI1 allow to select between CSI0/1 parallel input pads and any of the
four MIPI CSI-2 virtual channels.
Changes from Steve Longerbeam:
- Removed some dangling/unused endpoints (ipu2_csi0_from_csi2ipu)
- Renamed the mipi virtual channel endpoint labels, from "mipi_csiX_..."
to "mipi_vcX...".
- Added input endpoint anchors to the video muxes for the connections
from parallel sensors.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add to the MIPI CSI2 receiver node: compatible strings,
interrupt sources, and clocks.
Signed-off-by: Steve Longerbeam <steve_longerbeam@mentor.com>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The IOMUXC General Purpose Register space contains various bitfields
that control video bus multiplexers. Describe them using a mmio-mux
node. The placement of the IPU CSI video mux controls differs between
i.MX6D/Q and i.MX6S/DL.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Fabio Estevam <fabio.estevam@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add SHAM crypto accelerator.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has AES2 instance, so add its integration data under DT.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
"aes1_fck" and "aes2_fck" are controlled by hwmod. Drop clock
entries to avoid conflicts.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP4 has a second aes module, so let's use proper name for
the first instance.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The NAS4229B and SQ201 Gemini systems have a PATA controller
which is linked to a SATA bridge in the SoC. Enable both
platforms to use the PATA/SATA devices.
Cc: John Feng-Hsin Chiang <john453@faraday-tech.com>
Cc: Greentime Hu <green.hu@gmail.com>
Acked-by: Hans Ulli Kroll <ulli.kroll@googlemail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This adds the Faraday Technology FTDMAC020 DMA controller to
the Gemini SoC DTSI file. It is only used for memcpy work so
we can activate it for all users of the chipset.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This pull request brings in installation of the RPi3 DT in 32-bit
mode, the new thermal nodes, switches to the faster sdhost controller
for MMC, and enables USB OTG mode on the Pi 0.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
The APQ8060 Dragonboard has an Atmel AT24c128 EEPROM and a
Wolfson Micro WM8903 codec connected to its GSBI8 I2C bus.
Add entries for these to the device tree. The interrupt line
from the WM8903 chip is not routed anywhere on this design
so it can not be used.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Andy Gross <andy.gross@linaro.org>
|
|
dtc recently added PCI bus checks. Fix these warnings.
Signed-off-by: Rob Herring <robh@kernel.org>
Cc: Stephen Warren <swarren@wwwdotorg.org>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Alexandre Courbot <gnurou@gmail.com>
Cc: linux-tegra@vger.kernel.org
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Whistler is an ancient Tegra 2 reference board. I may have been the only
person who ever used it with upstream software, and I've just recycled
the board hardware. Hence, it makes sense to remove support from software.
Signed-off-by: Stephen Warren <swarren@nvidia.com>
Acked-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Since 635c21068cf ("usb: dwc2: gadget: Fix WARN_ON messages
during FIFO init") the dwc2 driver is able to handle OTG and gadget
mode for bcm2835. So enable this feature for the Raspberry Pi Zero.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
In order to use dwc2 in OTG or gadget mode the USB PHY should be
specified. Since there is no bcm283x USB PHY driver use the generic
one.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Acked-by: Stephen Warren <swarren@nvidia.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
The Raspberry Pi Zero also supports OTG mode. So provide a dtsi file
to configure the USB interface accordingly. The fifo sizes are optimized
for device endpoint 6 and 7 with the maximum of 768.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Eric Anholt <eric@anholt.net>
|
|
Cygnus has a single amac controller connected to the B53 switch with 2
PHYs. On the BCM911360_EP platform, those two PHYs are connected to the
external ethernet jacks.
Signed-off-by: Eric Anholt <eric@anholt.net>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Add thermal support via the ns-thermal driver and create a single
thermal zone for the entire SoC.
Signed-off-by: Jon Mason <jon.mason@broadcom.com>
Acked-by: Eduardo Valentin <edubezval@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This loads the VC4 driver on the 911360_entphn platform (with the
corresponding series sent to dri-devel), which is supported by master
of the Mesa tree.
Signed-off-by: Eric Anholt <eric@anholt.net>
Acked-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Northstar devices have MDIO bus that may contain various PHYs attached.
A common example is USB 3.0 PHY (that doesn't have an MDIO driver yet).
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This uses CPU thermal sensor available on every Northstar chipset to
monitor temperature. We don't have any cooling or throttling so only a
critical trip was added.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Jon Mason <jon.mason@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Configure CPCAP battery driver.
Cc: devicetree@vger.kernel.org
Cc: Marcel Partap <mpartap@gmx.net>
Cc: Michael Scott <michael.scott@linaro.org>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The GPU has two functional clocks - GPU_CORE_GCLK and GPU_HYD_GCLK.
Both of these are mux clocks and are derived from the DPLL_CORE
H14 output clock CORE_GPU_CLK by default. These clocks can also be
be derived from DPLL_PER or DPLL_GPU.
The GPU DPLL provides the output clocks primarily for the GPU.
Configuring the GPU for different OPP clock frequencies is easier
to achieve when using the DPLL_GPU rather than the other two DPLLs
due to:
1. minimal affect on any other output clocks from these DPLLs
2. may require an impossible post-divider values on existing DPLLs
without affecting other clocks.
So, switch the GPU functional clocks to be sourced from GPU DPLL by
default. This is done using the DT standard properties "assigned-clocks"
and "assigned-clock-parents". Newer u-boots (from 2017.01 onwards) reuse
and can update these properties to choose an appropriate one-time fixed
OPP configuration as all the required ABB/AVS setup is performed within
the bootloader. Note that there is no DVFS supported for any of the
non-MPU domains. The DPLL will automatically transition into a low-power
stop mode when the associated output clocks are not utilized or gated
automatically.
This patch also sets the initial values for the DPLL_GPU outputs.
These values are chosen based on the OPP_NOM values defined as per
recommendation from design team. The DPLL locked frequency is kept
at 1277 MHz, so that the value for the divider clock, dpll_gpu_m2_ck,
can be set to 425.67 MHz for OPP_NOM.
Signed-off-by: Subhajit Paul <subhajit_paul@ti.com>
[s-anna@ti.com: revise patch description]
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IVA DPLL in DRA7xx provides the output clocks for only the IVAHD
subsystem in DRA7xx as compared to previous OMAP generations when it
provided the clocks for both DSP and IVAHD subsystems. This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
IVA DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The reset value of the divider M2 (that supplies the IVA_GFLCK, the
functional clock for the IVAHD subsystem) does not match a specific
OPP. So, the derived output clock from this IVA DPLL has to be
initialized as well to avoid initializing these divider outputs to an
incorrect frequencies.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 2300 MHz, so
the dpll_iva_ck clock rate used is half of this value. The value for the
divider clock, dpll_iva_m2_ck, has to be set to 388.333334 MHz or more
for the divider clk logic to compute the appropriate divider value for
OPP_NOM.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The DSP DPLL is a new DPLL compared to previous OMAP generations and
supplies the root clocks for the DSP processors, as well as a mux
input source for EVE sub-system (on applicable SoCs). This DPLL is
currently not configured by older bootloaders. Use the DT standard
properties "assigned-clocks" and "assigned-clock-rates" to set the
DSP DPLL clock rate and the rates for its derivative clocks at boot
time to properly initialize/lock this DPLL and be independent of the
bootloader version. Newer u-boots (from 2017.01 onwards) reuse and
can update these properties to choose an appropriate one-time fixed
OPP configuration. The DPLL will automatically transition into a
low-power stop mode when the associated output clocks are not
utilized or gated automatically.
The DSP DPLL provides two output clocks, DSP_GFCLK and EVE_GCLK. The
desired rate for DSP_GFCLK is 600 MHz (same as DSP DPLL CLKOUT frequency),
and is currently auto set due to the desired M2 divider value being the
same as reset value for the locked frequency of 600 MHz. The EVE_GCLK
however is required to be 400 MHz, so set the dpll_dsp_m3x2_ck's rate
explicitly so that the divider is set properly. The dpll_dsp_m2_ck rate
is also set explicitly to not rely on any implicit matching divider reset
values to the locked DPLL frequency.
The OPP_NOM clock frequencies are defined in the AM572x SR2.0 Data
Sheet vB, section 5.5.2 "Voltage And Core Clock Specifications". The
clock rates are chosen based on these OPP_NOM values and defined as per
a DRA7xx PLL spec document. The DPLL locked frequency is 1200 MHz, so
the dpll_dsp_ck clock rate used is half of this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IPU1 functional clock is actually the output of a mux clock,
ipu1_gfclk_mux. The mux clock is sourced by default from the
DPLL_ABE_X2_CLK, and this results in a rather odd clock frequency
(361 MHz) for the IPU1 functional clock on platforms where ABE_DPLL
is configured properly. Reconfigure the mux clock to be sourced from
CORE_IPU_ISS_BOOST_CLK (dpll_core_h22x2_ck), so that both the IPU1
and IPU2 are running from the same clock and clocked at the same
nominal frequency of 425 MHz.
This also ensures that IPU1 functional clock is always configured
properly and becomes independent of the state of the ABE DPLL on
all boards.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers H11 & H12 (functional clocks for DSP
and IVAHD respectively) are identical to each other, but are different
at each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP_NOM values as defined in
the OMAP5432 SR2.0 Data Manual Book vK, section 5.2.3.5 "DPLL_IVA
Preferred Settings". The recommended maximum DPLL locked frequency is
2330 MHz for OPP_NOM (value for DPLL_IVA_X2_CLK), so the dpll_iva_ck
clock rate used is half of this value. The value 465.92 MHz is used
instead of 465.9 MHz for dpll_iva_h11x2_ck so that proper divider
value can be calculated.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The IVA DPLL is not an essential DPLL for the functionality of a
bootloader and is usually not configured (e.g. older u-boots configure
it only if CONFIG_SYS_CLOCKS_ENABLE_ALL is enabled and u-boots newer
than 2014.01 do not even have an option), and this results in incorrect
operating frequencies when trying to use a DSP or IVAHD, whose root
clocks are derived from this DPLL. Use the DT standard properties
"assigned-clocks" and "assigned-clock-rates" to set the IVA DPLL clock
rate and the rates for its derivative clocks at boot time to properly
initialize/lock this DPLL. The DPLL will automatically transition
into a low-power stop mode when the associated output clocks are
not utilized or gated automatically.
The reset values of the dividers M4 & M5 (functional clocks for DSP and
IVAHD respectively) are identical to each other, but are different at
each OPP. The reset values also do not match a specific OPP. So, the
derived output clocks from the IVA DPLL have to be initialized as well
to avoid initializing these divider outputs to incorrect frequencies.
The clock rates are chosen based on the OPP100 values as defined in the
OMAP4430 ES2.x Public TRM vAP, section "3.6.3.8.7 DPLL_IVA Preferred
Settings". The DPLL locked frequency is 1862.4 MHz (value for
DPLL_IVA_X2_CLK), so the dpll_iva_ck clock rate used is half of
this value.
Signed-off-by: Suman Anna <s-anna@ti.com>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Renesas Salvator-XS (Salvator-X 2nd version) development board can
be equipped with either an R-Car H3 ES2.0 or M3-W ES1.x SiP, which are
pin-compatible.
Document board part number and compatible values for the version with
R-Car H3.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The board part numbers for the R-Car H3 and M3 ULCB boards corresponded
to versions predating mass production. Update them for mass production.
Note that the H3 ULCB board can be equipped with either revision ES1.1
or ES2.0 of the R-Car H3 SoC. While these have different board part
numbers, no new compatible values are needed, as the revision can be
detected at runtime using the PRR register.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Vladimir Barinov <vladimir.barinov+renesas@cogentembedded.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G20D-Qseven-RZG1M device tree bindings,
listing it as a supported board.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Document the iW-RainboW-G20M-Qseven-RZG1M device tree bindings,
listing it as a supported system on module.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
The bogus 'device_type = "pci"' confuses dtc, causing lots of totally
unrelated warnings. After fixing that, real warnings like
arch/arm/boot/dts/r8a7790-lager.dtb: Warning (pci_device_reg): Node /pci@ee090000/usb@0,1 PCI unit address format error, expected "1,0"
are left. Correct the unit-addresses and reg properties of the subnodes
to fix these.
Signed-off-by: Rob Herring <robh@kernel.org>
[geert: Improve description]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for iWave RainboW-G20D-Qseven board based on RZ/G1M.
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add support for iWave RZG1M Qseven System On Module.
http://www.iwavesystems.com/rz-g1m-qseven-module.html
Signed-off-by: Biju Das <biju.das@bp.renesas.com>
Reviewed-by: Chris Paterson <chris.paterson2@renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Adds VIN, decoder and connector.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Add device tree source for Renesas GR-Peach board.
GR-Peach is an RZ/A1H based board with 10MB of on-chip SRAM and 8MB
QSPI flash storage.
Add support for the board, and create a 2MB partition to use as rootfs.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Motorola Droid 4 uses a WL1285C, so use proper compatible value.
To avoid regressions while support for the new compatible value
is added to the Linux kernel, the old compatible value is preserved
as fallback.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Droid 4 has a isl29030 to measure ambient light (e.g. for
automatically adapting display brightness) and proximity.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The Orange Pi Plus 2E, unlike the Orange Pi PC and PC Plus which its
schematics are based on, uses an external Realtek RTL8211E PHY in
RGMII mode, with a GPIO enabling the regulator for I/O signalling
power supplies. The PHY's main power supply is enabled by the main
5V power supply.
Add the regulator and PHY nodes, and override the PHY phandle under
the EMAC node, so that the EMAC works properly on this board.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>
|
|
This removes the dummy clk81 gate and replaces it with the actual clock
controller's CLKID_CLK81. This will also allow us to pass the real clock
IDs to all devices where the clock is controlled by clkc in the future.
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
The at24 driver allows to register I2C EEPROM chips using different vendor
and devices, but the I2C subsystem does not take the vendor into account
when matching using the I2C table since it only has device entries.
But when matching using an OF table, both the vendor and device has to be
taken into account so the driver defines only a set of compatible strings
using the "atmel" vendor as a generic fallback for compatible I2C devices.
So add this generic fallback to the device node compatible string to make
the device to match the driver using the OF device ID table.
Signed-off-by: Javier Martinez Canillas <javier@dowhile0.org>
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
Add basic support for stm32h743i-discovery board
This board offers :
_ 2MBytes Flash
_ 1 x micro USB OTG port
_ 1 x STLink connector (micro USB)
_ 1 x micro SD card slot
_ 1 x RJ45 connector
_ 1 x RCA connector
_ 2 x Audio jack connectors (in and out)
_ 2 x speaker connectors (left and right)
_ 1 x joystick
_ 1 x DCMI connector (Digital camera interface)
_ 1 x 4 inch DSI LCD (Display Serial Interface)
_ Arduino Uno Connectors
_ 2 x PIO connectors (PMOD and PMOD+)
_ 1 x wakeup button
_ 1 x reset button
Signed-off-by: Patrice Chotard <patrice.chotard@st.com>
Signed-off-by: Alexandre TORGUE <alexandre.torgue@st.com>
|
