| Age | Commit message (Collapse) | Author |
|---|
|
When clearing the DMA channel, clear all status bits.
When handling a DMA interrupt, clear only the interrupt
status bits that have been read and are passed to the
channel's interrupt handler, not every status bit.
Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com>
Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
Acked-by: G, Manjunath Kondaiah <manjugk@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
gpio7 on the tps65930 is used as an output on the devkit8000 and
gpio1 is not connected. Remove gpio7 and change gpio1 to pulldown
Signed-off-by: Daniel Morsing <daniel.morsing@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
commit 0363466866d901fbc (net offloading: Convert checksums to use
centrally computed features.) mistakenly swapped can_checksum_protocol()
arguments.
This broke IPv6 on bnx2 for instance, on NIC without TCPv6 checksum
offloads.
Reported-by: Hans de Bruin <jmdebruin@xmsnet.nl>
Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com>
Acked-by: Jesse Gross <jesse@nicira.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
offsets in the comment were wrong - fix this.
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Fix rtc gpios and mux
Signed-off-by: Igor Grinberg <grinberg@compulab.co.il>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
This reverts commit 0ab03c2b1478f2438d2c80204f7fef65b1bca9cf.
It breaks several things including the avahi daemon.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
user, group, and other
If a DACL has entries for ACEs for SID Everyone and Authenticated Users,
factor in mask in respective entries during calculation of permissions
for all three, user, group, and other.
http://technet.microsoft.com/en-us/library/bb463216.aspx
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Reviewed-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
When NOHZ=y and high res timers are disabled (via cmdline or
Kconfig) tick_nohz_switch_to_nohz() will notify the user about
switching into NOHZ mode. Nothing is printed for the case where
HIGH_RES_TIMERS=y. Fix this for the HIGH_RES_TIMERS=y case by
duplicating the printk from the low res NOHZ path in the high
res NOHZ path.
This confused me since I was thinking 'dmesg | grep -i NOHZ' would
tell me if NOHZ was enabled, but if I have hrtimers there is
nothing.
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <1295419594-13085-1-git-send-email-sboyd@codeaurora.org>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
When fixing the frequency calculations for perf on powerpc I
forgot to fix the FSL version.
If we dont set event->hw.last_period the frequency to period
calculations in perf go haywire and we continually
throttle/unthrottle the PMU.
Signed-off-by: Anton Blanchard <anton@samba.org>
Acked-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Scott Wood <scottwood@freescale.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Arnaldo Carvalho de Melo <acme@ghostprotocols.net>
Cc: linuxppc-dev@lists.ozlabs.org
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
LKML-Reference: <20110118214404.2f42e634@kryten>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
perf_event_init_task() should clear child->perf_event_ctxp[]
before anything else. Otherwise, if
perf_event_init_context(perf_hw_context) fails,
perf_event_free_task() can free perf_event_ctxp[perf_sw_context]
copied from parent->perf_event_ctxp[] by dup_task_struct().
Also move the initialization of perf_event_mutex and
perf_event_list from perf_event_init_context() to
perf_event_init_context().
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
LKML-Reference: <20110119182228.GC12183@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
find_get_context() must not install the new perf_event_context
if the task has already passed perf_event_exit_task().
If nothing else, this means the memory leak. Initially
ctx->refcount == 2, it is supposed that
perf_event_exit_task_context() should participate and do the
necessary put_ctx().
find_lively_task_by_vpid() checks PF_EXITING but this buys
nothing, by the time we call find_get_context() this task can be
already dead. To the point, cmpxchg() can succeed when the task
has already done the last schedule().
Change find_get_context() to populate task->perf_event_ctxp[]
under task->perf_event_mutex, this way we can trust PF_EXITING
because perf_event_exit_task() takes the same mutex.
Also, change perf_event_exit_task_context() to use
rcu_dereference(). Probably this is not strictly needed, but
with or without this change find_get_context() can race with
setup_new_exec()->perf_event_exit_task(), rcu_dereference()
looks better.
Signed-off-by: Oleg Nesterov <oleg@redhat.com>
Acked-by: Peter Zijlstra <a.p.zijlstra@chello.nl>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: Arnaldo Carvalho de Melo <acme@redhat.com>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Prasad <prasad@linux.vnet.ibm.com>
Cc: Roland McGrath <roland@redhat.com>
LKML-Reference: <20110119182207.GB12183@redhat.com>
Signed-off-by: Ingo Molnar <mingo@elte.hu>
|
|
Earlier patches select HAVE_SCHED_CLOCK for omaps. To have working sched_clock
also for MPU timer, we need to implement it in a way where the right one gets
selected during the runtime.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
For omap15xx and 730 we need to use the MPU timer
as the 32K timer is not available. For omap16xx
we want to use the 32K timer because of PM. Fix this
by allowing to build in both timers.
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
NTLM response length was changed to 16 bytes instead of 24 bytes
that are sent in Tree Connection Request during share-level security
share mounts. Revert it back to 24 bytes.
Reported-and-Tested-by: Grzegorz Ozanski <grzegorz.ozanski@intel.com>
Acked-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Shirish Pargaonkar <shirishpargaonkar@gmail.com>
Acked-by: Suresh Jayaraman <sjayaraman@suse.de>
Cc: stable@kernel.org
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
In later patches, we're going to need to have finer-grained control
over the addition and removal of these structs from the pending_mid_q
and we'll need to be able to call the destructor while holding the
spinlock. Move the locked sections out of both routines and into
the callers. Fix up current callers of DeleteMidQEntry to call a new
routine that dequeues the entry and then destroys it.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
It's an atomic_t and the code accesses the "counter" field in it directly
instead of using atomic_read(). It also is sometimes accessed under a
spinlock and sometimes not. Move it out of the spinlock since we don't need
belt-and-suspenders for something that's just informational.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The cifsSesInfo pointer is only used to get at the server.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The TCP_Server_Info is refcounted and every SMB session holds a
reference to it. Thus, smb_ses_list is always going to be empty when
cifsd is coming down. This is dead code.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
If CIFSSMBWrite2 returns -EAGAIN, then the error should be considered
temporary. CIFS should retry the write instead of setting an error on
the mapping and returning.
For WB_SYNC_ALL, just retry the write immediately. In the WB_SYNC_NONE
case, call redirty_page_for_writeback on all of the pages that didn't
get written out and then move on.
Also, fix up the handling of a short write with a successful return
code. MS-CIFS says that 0 bytes_written means ENOSPC or EFBIG. It
doesn't mention what a short, but non-zero write means, so for now
treat it as we would an -EAGAIN return.
Reviewed-by: Suresh Jayaraman <sjayaraman@suse.de>
Reviewed-by: Pavel Shilovsky <piastryyy@gmail.com>
Signed-off-by: Jeff Layton <jlayton@redhat.com>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
When we get oplock break notification we should set the appropriate
value of OplockLevel field in oplock break acknowledge according to
the oplock level held by the client in this time. As we only can have
level II oplock or no oplock in the case of oplock break, we should be
aware only about clientCanCacheRead field in cifsInodeInfo structure.
Also fix bug connected with wrong interpretation of OplockLevel field
during oplock break notification processing.
Signed-off-by: Pavel Shilovsky <piastryyy@gmail.com>
Cc: <stable@kernel.org>
Signed-off-by: Steve French <sfrench@us.ibm.com>
|
|
The conn->sec_level value is supposed to represent the current level of
security that the connection has. However, by assigning to it before
requesting authentication it will have the wrong value during the
authentication procedure. To fix this a pending_sec_level variable is
added which is used to track the desired security level while making
sure that sec_level always represents the current level of security.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
When there is an existing connection l2cap_check_security needs to be
called to ensure that the security level of the new socket is fulfilled.
Normally l2cap_do_start takes care of this, but that function doesn't
get called for SOCK_RAW type sockets. This patch adds the necessary
l2cap_check_security call to the appropriate branch in l2cap_do_connect.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The logic for determining the needed auth_type for an L2CAP socket is
rather complicated and has so far been duplicated in
l2cap_check_security as well as l2cap_do_connect. Additionally the
l2cap_check_security code was completely missing the handling of
SOCK_RAW type sockets. This patch creates a unified function for the
evaluation and makes l2cap_do_connect and l2cap_check_security use that
function.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
If an existing connection has a MITM protection requirement (the first
bit of the auth_type) then that requirement should not be cleared by new
sockets that reuse the ACL but don't have that requirement.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
This reverts commit 045309820afe047920a50de25634dab46a1e851d. That
commit is wrong for two reasons:
- The conn->sec_level shouldn't be updated without performing
authentication first (as it's supposed to represent the level of
security that the existing connection has)
- A higher auth_type value doesn't mean "more secure" like the commit
seems to assume. E.g. dedicated bonding with MITM protection is 0x03
whereas general bonding without MITM protection is 0x04. hci_conn_auth
already takes care of updating conn->auth_type so hci_connect doesn't
need to do it.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
Fix a bug introduced in commit 9cf5b0ea3a7f1432c61029f7aaf4b8b338628884:
function rfcomm_recv_ua calls rfcomm_session_put without checking that
the session is not referenced by some DLC. If the session is freed, that
DLC would refer to deallocated memory, causing an oops later, as shown
in this bug report: https://bugzilla.kernel.org/show_bug.cgi?id=15994
Signed-off-by: Lukas Turek <8an@praha12.net>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
The blacklist should be freed before the hci device gets unregistered.
Signed-off-by: Johan Hedberg <johan.hedberg@nokia.com>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
CC: Marcel Holtmann <marcel@holtmann.org>
CC: "Gustavo F. Padovan" <padovan@profusion.mobi>
CC: João Paulo Rechi Vita <jprvita@profusion.mobi>
Signed-off-by: David Sterba <dsterba@suse.cz>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
There is no need to hold the firmware in memory.
Signed-off-by: Alexander Holler <holler@ahsoftware.de>
Signed-off-by: Gustavo F. Padovan <padovan@profusion.mobi>
|
|
sound/pci/hda/patch_realtek.c: In function ‘alc_apply_fixup’:
sound/pci/hda/patch_realtek.c:1724:14: warning: unused variable ‘modelname’
snd_printdd() is evaluated only when CONFIG_SND_DEBUG_VERBOSE=y.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
Commit a4f740cf, "of/flattree: Add of_flat_dt_match() helper function"
introduced build failures in arch/powerpc/platform/83xx by mistyping
'static' as 'struct' in the compatible string list, and omitting a few
semicolons. This patch fixes it.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
|
|
It seems working well with model=hp-bpc.
Signed-off-by: Takashi Iwai <tiwai@suse.de>
|
|
When the lirc drivers were converted over to using memdup_user, I
mistakenly also removed corresponding calls to kfree. Add those back. I
also screwed up on the allocation error check in lirc_serial, using if
(PTR_ERR()) instead of if (IS_ERR()), which broke transmit.
Reported-by: Jiri Fojtasek <jiri.fojtasek@hlohovec.net>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The current hdpvr code kmalloc's a new buffer for every i2c read and
write. Rather than do that, lets allocate a buffer in the driver's
device struct and just use that every time.
The size I've chosen for the buffer is the maximum size I could
ascertain might be used by either ir-kbd-i2c or lirc_zilog, plus a bit
of padding (lirc_zilog may use up to 100 bytes on tx, rounded that up
to 128).
Note that this might also remedy user reports of very sluggish behavior
of IR receive with hdpvr hardware.
v2: make sure (len <= (dev->i2c_buf)) [Jean Delvare]
Reported-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
A number of things going on here, but the end result is that the IR part
on the hdpvr gets enabled, and can be used with ir-kbd-i2c and/or
lirc_zilog.
First up, there are some conditional build fixes that come into play
whether i2c is built-in or modular. Second, we're swapping out
i2c_new_probed_device() for i2c_new_device(), as in my testing, probing
always fails, but we *know* that all hdpvr devices have a z8 chip at
0x70 and 0x71. Third, we're poking at an i2c address directly without a
client, and writing some magic bits to actually turn on this IR part
(this could use some improvement in the future). Fourth, some of the
i2c_adapter storage has been reworked, as the existing implementation
used to lead to an oops following i2c changes c. 2.6.31.
Earlier editions of this patch have been floating around the 'net for a
while, including being patched into Fedora kernels, and they *do* work.
This specific version isn't yet tested, beyond loading ir-kbd-i2c and
confirming that it does bind to the RX address of the hdpvr.
[mchehab@redhat.com: I2C_CLASS_TV_ANALOG is not defined. Fix compilation bug]
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Acked-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes an egregious bug in mceusb driver, where the receiver was being
put into idle mode far sooner than it should have, thanks to storing a
timeout value that in us where it should be ns. Basically, the receiver
kept going into idle mode before a trailing space had been fully
received, which was causing problems for some protocols, most notably
manifesting as lirc userspace never receiving a trailing space for any
rc5 signals.
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fix a bug in v4l2_device_unregister where the sd pointer can be dereferenced
after it was freed.
Normally the i2c adapter is removed before this function is called. Removing
the adapter will also unregister all subdevs on that adapter, so generally
v4l2_device_unregister has nothing to do. However, in the case of a platform
i2c bus that bus is generally not freed.
In that case, after freeing the i2c subdevice the code will fall into the
second block when it tests if the subdev is a SPI device. But by that time
the subdev is already freed and the kernel oopses.
The fix is trivial: continue with the loop after freeing the i2c or spi
subdevice.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Reported-by: Daniel Drake <dsd@laptop.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Zeroing video_device.dev causes a memory leak if video_set_drvdata
was called before video_register_device was called. video_set_drvdata
calls dev_set_drvdata which allocates video_device.dev.p.
memsetting this will prevent freeing of that memory.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
After a detach zero the whole device state to ensure a clean slate
on the next attach.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
v4l2_queryctrl sets the step value based on the control type. That would
be fine if it used the control type stored in the V4L2 kernel control
object, not the one stored in the userspace ioctl structure that has
just been memset to 0. Fix this.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The later makes extensive use of structures defined in the former.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
V4L2_CID_PRIVATE_BASE IDs
When queryctrl is called with a V4L2_CID_PRIVATE_BASE control ID, then
currently it is replaced by the real internal ID. This is not according to
the spec so keep the V4L2_CID_PRIVATE_BASE ID in this case.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
VIDIOC_S_CTRL did not check against read-only controls. Even worse, for
controls of type CTRL_CLASS it would cause a kernel oops since those controls
do not have a s_ctrl op.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
ir-kbd-i2c
When registering an IR Rx device with the I2C subsystem, provide more detailed
information about the IR device and default remote configuration for the IR
driver modules.
Also explicitly register any IR Tx device with the I2C subsystem.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Acked-by: Mike Isely <isely@pobox.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This reverts a portion of commit
44243fc2ef99948bc9b046901880885616dd5e89
A commit for which I errantly recommended that defaults for I2C address
0x71 not be set by ir-kbd-i2c.c
The pvrusb2 and bttv drivers currently rely on ir-kbd-i2c setting
defaults for that address. Until I can get those bridge drivers fixed
to properly send IR_i2c_init_data for boards with Zilog Z8 chips,
just add back the default settings for I2C address 0x71.
Signed-off-by: Andy Walls <awalls@md.metrocast.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
