summaryrefslogtreecommitdiff
AgeCommit message (Collapse)Author
2018-10-01mt76: add stbc entries to mt76_rate_powerFelix Fietkau
Add stbc tx power eeprom parsing support for mt76x2 driver. When writing power entries, make a distinction between rates that are read from the same EEPROM value, but have separate register entries. No effect on runtime behavior, but preparation for unification with mt76x0 and for placing restrictions on individual rate power limits Signed-off-by: Felix Fietkau <nbd@nbd.name> Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-01mt76: move seq_put_array in mt76-core moduleLorenzo Bianconi
Move seq_put_array utility routine in mt76-core module in order to be reused in mt76x0 driver Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-01mt76x0: pci: add fw uploading routineLorenzo Bianconi
Add pci load firmware routine. Move some shared mcu definitions in mt76x02_mcu.h Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-01mt76x0: pci: add mt7650 PCI IDLorenzo Bianconi
Add mt7650 PCI id found on ASUS rt-51ac to pci_device_id table Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-10-01mt76x2: fix tx power configuration for VHT mcs 9Lorenzo Bianconi
Fix tx power configuration for VHT 1SS/STBC mcs 9 since in MT_TX_PWR_CFG_{8,9} mcs 8,9 bits are GENMASK(21,16) and GENMASK(29,24) while GENMASK(15,6) are marked as reserved Fixes: 7bc04215a66b ("mt76: add driver code for MT76x2e") Signed-off-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com> Signed-off-by: Felix Fietkau <nbd@nbd.name>
2018-09-29openvswitch: Use correct reply values in datapath and vport opsYifeng Sun
This patch fixes the bug that all datapath and vport ops are returning wrong values (OVS_FLOW_CMD_NEW or OVS_DP_CMD_NEW) in their replies. Signed-off-by: Yifeng Sun <pkusunyifeng@gmail.com> Acked-by: Pravin B Shelar <pshelar@ovn.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tls: Remove redundant vars from tls record structureVakul Garg
Structure 'tls_rec' contains sg_aead_in and sg_aead_out which point to a aad_space and then chain scatterlists sg_plaintext_data, sg_encrypted_data respectively. Rather than using chained scatterlists for plaintext and encrypted data in aead_req, it is efficient to store aad_space in sg_encrypted_data and sg_plaintext_data itself in the first index and get rid of sg_aead_in, sg_aead_in and further chaining. This requires increasing size of sg_encrypted_data & sg_plaintext_data arrarys by 1 to accommodate entry for aad_space. The code which uses sg_encrypted_data and sg_plaintext_data has been modified to skip first index as it points to aad_space. Signed-off-by: Vakul Garg <vakul.garg@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29Merge branch 'tipc-next'David S. Miller
Jon Maloy says: ==================== tipc: make connection setup more robust In this series we make a few improvements to the connection setup and probing mechanism, culminating in the last commit where we make it possible for a client socket to make multiple setup attempts in case it encounters receive buffer overflow at the listener socket. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tipc: buffer overflow handling in listener socketTung Nguyen
Default socket receive buffer size for a listener socket is 2Mb. For each arriving empty SYN, the linux kernel allocates a 768 bytes buffer. This means that a listener socket can serve maximum 2700 simultaneous empty connection setup requests before it hits a receive buffer overflow, and much fewer if the SYN is carrying any significant amount of data. When this happens the setup request is rejected, and the client receives an ECONNREFUSED error. This commit mitigates this problem by letting the client socket try to retransmit the SYN message multiple times when it sees it rejected with the code TIPC_ERR_OVERLOAD. Retransmission is done at random intervals in the range of [100 ms, setup_timeout / 4], as many times as there is room for within the setup timeout limit. Signed-off-by: Tung Nguyen <tung.q.nguyen@dektech.com.au> Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tipc: add SYN bit to connection setup messagesJon Maloy
Messages intended for intitating a connection are currently indistinguishable from regular datagram messages. The TIPC protocol specification defines bit 17 in word 0 as a SYN bit to allow sanity check of such messages in the listening socket, but this has so far never been implemented. We do that in this commit. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tipc: refactor function tipc_sk_filter_connect()Jon Maloy
We refactor the function tipc_sk_filter_connect(), both to make it more readable and as a preparation for the next commit. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tipc: refactor function tipc_sk_timeout()Jon Maloy
We refactor this function as a preparation for the coming commits in the same series. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tipc: refactor function tipc_msg_reverse()Jon Maloy
The function tipc_msg_reverse() is reversing the header of a message while reusing the original buffer. We have seen at several occasions that this may have unfortunate side effects when the buffer to be reversed is a clone. In one of the following commits we will again need to reverse cloned buffers, so this is the right time to permanently eliminate this problem. In this commit we let the said function always consume the original buffer and replace it with a new one when applicable. Acked-by: Ying Xue <ying.xue@windriver.com> Signed-off-by: Jon Maloy <jon.maloy@ericsson.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29tcp: up initial rmem to 128KB and SYN rwin to around 64KBYuchung Cheng
Previously TCP initial receive buffer is ~87KB by default and the initial receive window is ~29KB (20 MSS). This patch changes the two numbers to 128KB and ~64KB (rounding down to the multiples of MSS) respectively. The patch also simplifies the calculations s.t. the two numbers are directly controlled by sysctl tcp_rmem[1]: 1) Initial receiver buffer budget (sk_rcvbuf): while this should be configured via sysctl tcp_rmem[1], previously tcp_fixup_rcvbuf() always override and set a larger size when a new connection establishes. 2) Initial receive window in SYN: previously it is set to 20 packets if MSS <= 1460. The number 20 was based on the initial congestion window of 10: the receiver needs twice amount to avoid being limited by the receive window upon out-of-order delivery in the first window burst. But since this only applies if the receiving MSS <= 1460, connection using large MTU (e.g. to utilize receiver zero-copy) may be limited by the receive window. With this patch TCP memory configuration is more straight-forward and more properly sized to modern high-speed networks by default. Several popular stacks have been announcing 64KB rwin in SYNs as well. Signed-off-by: Yuchung Cheng <ycheng@google.com> Signed-off-by: Wei Wang <weiwan@google.com> Signed-off-by: Neal Cardwell <ncardwell@google.com> Signed-off-by: Eric Dumazet <edumazet@google.com> Reviewed-by: Soheil Hassas Yeganeh <soheil@google.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29hns3: Another build fix.David S. Miller
drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c: In function ‘hclge_get_sset_count’: drivers/net/ethernet/hisilicon/hns3/hns3pf/hclge_main.c:496:31: error: ‘HNAE3_REVISION_ID_21’ undeclared (first use in this function); did you mean ‘FADT2_REVISION_ID’? if (hdev->pdev->revision >= HNAE3_REVISION_ID_21 || ^~~~~~~~~~~~~~~~~~~~ FADT2_REVISION_ID Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-29hns3: Fix the build.David S. Miller
drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c: In function ‘hns3_self_test’: drivers/net/ethernet/hisilicon/hns3/hns3_ethtool.c:278:15: error: ‘HNS3_SELF_TEST_TYPE_NUM’ undeclared (first use in this function); did you mean ‘HNS3_SELF_TEST_TPYE_NUM’? int st_param[HNS3_SELF_TEST_TYPE_NUM][2]; ^~~~~~~~~~~~~~~~~~~~~~~ HNS3_SELF_TEST_TPYE_NUM Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28Bluetooth: Fix debugfs NULL pointer dereferenceMatias Karhumaa
Fix crash caused by NULL pointer dereference when debugfs functions le_max_key_read, le_max_key_size_write, le_min_key_size_read or le_min_key_size_write and Bluetooth adapter was powered off. Fix is to move max_key_size and min_key_size from smp_dev to hci_dev. At the same time they were renamed to le_max_key_size and le_min_key_size. BUG: unable to handle kernel NULL pointer dereference at 00000000000002e8 PGD 0 P4D 0 Oops: 0000 [#24] SMP PTI CPU: 2 PID: 6255 Comm: cat Tainted: G D OE 4.18.9-200.fc28.x86_64 #1 Hardware name: LENOVO 4286CTO/4286CTO, BIOS 8DET76WW (1.46 ) 06/21/2018 RIP: 0010:le_max_key_size_read+0x45/0xb0 [bluetooth] Code: 00 00 00 48 83 ec 10 65 48 8b 04 25 28 00 00 00 48 89 44 24 08 31 c0 48 8b 87 c8 00 00 00 48 8d 7c 24 04 48 8b 80 48 0a 00 00 <48> 8b 80 e8 02 00 00 0f b6 48 52 e8 fb b6 b3 ed be 04 00 00 00 48 RSP: 0018:ffffab23c3ff3df0 EFLAGS: 00010246 RAX: 0000000000000000 RBX: 00007f0b4ca2e000 RCX: ffffab23c3ff3f08 RDX: ffffffffc0ddb033 RSI: 0000000000000004 RDI: ffffab23c3ff3df4 RBP: 0000000000020000 R08: 0000000000000000 R09: 0000000000000000 R10: ffffab23c3ff3ed8 R11: 0000000000000000 R12: ffffab23c3ff3f08 R13: 00007f0b4ca2e000 R14: 0000000000020000 R15: ffffab23c3ff3f08 FS: 00007f0b4ca0f540(0000) GS:ffff91bd5e280000(0000) knlGS:0000000000000000 CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033 CR2: 00000000000002e8 CR3: 00000000629fa006 CR4: 00000000000606e0 Call Trace: full_proxy_read+0x53/0x80 __vfs_read+0x36/0x180 vfs_read+0x8a/0x140 ksys_read+0x4f/0xb0 do_syscall_64+0x5b/0x160 entry_SYSCALL_64_after_hwframe+0x44/0xa9 Signed-off-by: Matias Karhumaa <matias.karhumaa@gmail.com> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-28ice: fix changing of ring descriptor size (ethtool -G)Bruce Allan
rx_mini_pending was set to an incorrect value. This was causing EINVAL to always be returned to 'ethtool -G'. The driver does not support mini or jumbo rings so the respective settings should be zero. Also, change the valid range of the number of descriptors in the rings to make the code simpler and easier for users to understand (this removes the valid settings of 8 and 16). Add a system log message indicating when the number is rounded-up from what the user specifies with the 'ethtool -G' command (i.e. when it is not a multiple of 32), and update the log message when a user-provided value is out of range to also indicate the stride. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: Update to capabilities admin queue commandAnirudh Venkataramanan
This patch makes a couple of changes in the way the driver uses the "get capabilities" command. 1. Get device capabilities in addition to function capabilities 2. Align to latest spec by using cap_count to determine size of the buffer in case of length error. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: Query the Tx scheduler node before adding itAnirudh Venkataramanan
Query the Tx scheduler tree node information from FW before adding it to the driver's software database. This will keep the node information current in driver. Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: Update comment for ice_fltr_mgmt_list_entryBrett Creeley
Previously the comment stated that VSI lists should be used when a second VSI becomes a subscriber to the "VLAN address". VSI lists are always used for VLAN membership, so replace "VLAN address" with "MAC address". Also note that VLAN(s) always use VSI list rules. Signed-off-by: Brett Creeley <brett.creeley@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: update fw version check logicJacob Keller
We have MAX_FW_API_VER_BRANCH, MAX_FW_API_VER_MAJOR, and MAX_FW_API_VER_MINOR that we use in ice_controlq.h to test when a firmware version is newer than expected. This is currently tested by comparing each field separately. Thus, we compare the branch field against the MAX_FW_API_VER_BRANCH, and so forth. This means that currently, if we suppose that the max firmware version is defined as 0.2.1, i.e. Then firmware 0.1.3 will fail to load. This is because the minor version 3 is greater than the max minor version 1. This is not intuitive, because of the notion that increasing the major firmware version to 2 should mean any firmware version with a major version is less than 2 should be considered older than 2... In order to allow both 0.2.1 and 0.1.3 to load, you would have to define the "max" firmware version as 0.2.3.. It is possible that such a firmware version doesn't even exist yet! Fix this by replacing the current logic with an updated check that behaves as follows: First, we check the major version. If it is greater than the expected version, then we prevent driver load. Additionally, a warning message is logged to indicate to the system administrator that they need to update their driver. This is now the only case where the driver will refuse to load. Second, if the major version is less than the expected version, we log an information message indicating the NVM should be updated. Third, if the major version is exact, we'll then check the minor version. If the minor version is more than two versions less than expected, we log an information message indicating the NVM should be updated. If it is more than two versions greater than the expected version, we log an information message that the driver should be updated. To support this, the ice_aq_ver_check function needs its signature updated to pass the HW structure. Since we now pass this structure, there is no need to pass the firmware API versions separately. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: update branding strings and supported device idsBruce Allan
Update branding strings and remove device ids 0x1594 and 0x1595. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: replace unnecessary memcpy with direct assignmentBruce Allan
Direct assignment is preferred over a memcpy() Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28ice: use [sr]q.count when checking if queue is initializedJacob Keller
When shutting down the controlqs, we check if they are initialized before we shut them down and destroy the lock. This is important, as it prevents attempts to access the lock of an already shutdown queue. Unfortunately, we checked rq.head and sq.head as the value to determine if the queue was initialized. This doesn't work, because head is not reset when the queue is shutdown. In some flows, the adminq will have already been shut down prior to calling ice_shutdown_all_ctrlqs. This can result in a crash due to attempting to access the already destroyed mutex. Fix this by using rq.count and sq.count instead. Indeed, ice_shutdown_sq and ice_shutdown_rq already indicate that this is the value we should be using to determine of the queue was initialized. Signed-off-by: Jacob Keller <jacob.e.keller@intel.com> Signed-off-by: Anirudh Venkataramanan <anirudh.venkataramanan@intel.com> Tested-by: Andrew Bowers <andrewx.bowers@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2018-09-28qed: fix spelling mistake "b_cb_registred" -> "b_cb_registered"Colin Ian King
Trivial fix to spelling mistake struct field name, rename it. Signed-off-by: Colin Ian King <colin.king@canonical.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28Merge branch '100GbE' of ↵David S. Miller
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue Jeff Kirsher says: ==================== 100GbE Intel Wired LAN Driver Updates 2018-09-27 This series contains fixes to the ice driver only. Jake fixes a potential crash due to attempting to access the mutex which is already destroyed. Fix this by using rq.count and sq.count to determine if the queue was initialized. Fixed the current logic for checking the firmware version to properly handle situations when firmware major/minor versions differ and when the branch version differs. Bruce replaces a memcpy() with a direct assignment, which is preferred. Also updated the branding strings and device ids supported by the driver. Fixed the "ethtool -G" command in the driver, which was always returning EINVAL when changing the descriptor ring size. Brett update and clarified code comments. Anirudh updates the driver to ensure we query the firmware for the transmit scheduler node information before adding it to the driver database, to ensure we have the current information. Also update the "get capabilities" command to get device and function capabilities. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: sched: make function qdisc_free_cb() staticWei Yongjun
Fixes the following sparse warning: net/sched/sch_generic.c:944:6: warning: symbol 'qdisc_free_cb' was not declared. Should it be static? Fixes: 3a7d0d07a386 ("net: sched: extend Qdisc with rcu") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28selftests: forwarding: test for bridge sticky flagNikolay Aleksandrov
This test adds an fdb entry with the sticky flag and sends traffic from a different port with the same mac as a source address expecting the entry to not change ports if the flag is operating correctly. Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: bridge: explicitly zero is_sticky in fdb_createNikolay Aleksandrov
We need to explicitly zero is_sticky when creating a new fdb, otherwise we might get a stale value for a new entry. Fixes: 435f2e7cc0b7 ("net: bridge: add support for sticky fdb entries") Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28Merge branch 'hns3-next'David S. Miller
Salil Mehta says: ==================== Cleanups, minor additions & fixes for HNS3 driver This patch-set contains cleans-ups, minor changes and fixes to the HNS3 driver. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Fix loss of coal configuration while doing resetHuazhong Tan
The user's coal configuration will be lost after reset, so the tx_coal and rx_coal fields are added to the struct hns_nic_priv to save the coal configuration and used to restore the user's configuration after the reset is complete. Fixes: bb6b94a896d4 ("net: hns3: Add reset interface implementation in client") Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Modify hns3_get_max_available_channelsHuazhong Tan
The current hns3_get_max_available_channels returns the total number of queues for the device, which makes ethtool -L set the number of queues per channel queues incorrectly, so hns3_get_max_available_channels should return the maximum available number of queues per channel, depending on the total number of queues allocated and the hardware configurations. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Change return type of hclge_tm_schd_info_update()Huazhong Tan
hclge_tm_schd_info_update should return an error when num_tc is greater than alloc_tqps. This patch changes the return type of hnae3_register_ae_algo from void to int. Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com> Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Fix for netdev not up problem when setting mtuYunsheng Lin
Currently hns3_nic_change_mtu will try to down the netdev before setting mtu, and it does not up the netdev when the setting fails, which causes netdev not up problem. This patch fixes it by not returning when the setting fails. Fixes: a8e8b7ff3517 ("net: hns3: Add support to change MTU in HNS3 hardware") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Fix for packet buffer setting bugYunsheng Lin
The hardware expects a unit of 128 bytes when setting packet buffer. When calculating the packet buffer size, hclge_rx_buffer_calc does not round up the size as a unit of 128 byte, which may casue packet lost problem when stress testing. This patch fixes it by rounding up packet size when calculating. Fixes: 46a3df9f9718 ("net: hns3: Add HNS3 Acceleration Engine & Compatibility Layer Support") Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Add serdes parallel inner loopback supportFuyun Liang
This patch adds serdes parallel inner loopback support for self test. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Rename mac loopback to app loopbackFuyun Liang
In fact, our implementation of mac loopback is the implementation of app loopback now. Current name is wrong. This patch renames mac loopback to app loopback. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Rename loop modeFuyun Liang
Our loop mode includes mac loop, serdes loop and phy loop. Not all of them are related with mac. This patch corrects their names. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Set extra mac address of pause param for HWFuyun Liang
The extra mac address of pause param is used to do double check for pause frame. This patch set it to HW. If we do not do that, pfc pause frame will be transferred protocol stack when normal flow control mode is enabled. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: hns3: Add support for sctp checksum offloadPeng Li
This patch adds support for sctp checksum offload. Signed-off-by: Fuyun Liang <liangfuyun1@huawei.com> Signed-off-by: Peng Li <lipeng321@huawei.com> Signed-off-by: Salil Mehta <salil.mehta@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: dsa: b53: Fix build with B53_SRAB enabled and B53_SERDES=mArnd Bergmann
When B53_SERDES is a loadable module, a built-in srab driver still cannot reach it, so the previous fix is incomplete: b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init' drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state' drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set' drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart' drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate' drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config' Add a Kconfig dependency that forces srab to also be a module in this case, but allow it to be built-in when serdes is disabled or built-in. Fixes: 7a8c7f5c30f9 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28Bluetooth: ath3k: add more information to error messageLuiz Carlos Ramos
When there is an error in either ath3k_load_firmware() or ath3k_load_fwfile(), the inlined function ath3k_log_failed_loading() is called receiving the error returned and both the block size requested to load and the size actually loaded. These values are printed in an error message using the macro BT_ERR. This patch changes that function in order to print the variable "count" as well, to show more information when a failing firmware loading operation happens. The calls to the older function were changed to the new one. This event is being monitored in a laptop with an adapter which identifies itself as 0cf3:0036, where sometimes there are errors in the firmware loading process. Signed-off-by: Luiz Carlos Ramos <lramos.prof@yahoo.com.br> Signed-off-by: Marcel Holtmann <marcel@holtmann.org>
2018-09-28net: phy: mdio-bcm-unimac: mark PM functions as __maybe_unusedArnd Bergmann
The newly added runtime-pm support causes a harmless warning when CONFIG_PM is disabled: drivers/net/phy/mdio-bcm-unimac.c:330:12: error: 'unimac_mdio_resume' defined but not used [-Werror=unused-function] static int unimac_mdio_resume(struct device *d) drivers/net/phy/mdio-bcm-unimac.c:321:12: error: 'unimac_mdio_suspend' defined but not used [-Werror=unused-function] static int unimac_mdio_suspend(struct device *d) Marking the functions as __maybe_unused is the easiest workaround and avoids adding #ifdef checks. Fixes: b78ac6ecd1b6 ("net: phy: mdio-bcm-unimac: Allow configuring MDIO clock divider") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28phy: mscc: fix printf formatArnd Bergmann
gcc points out that the length of the temporary buffer may not be sufficient for large numbers of leds: drivers/net/phy/mscc.c: In function 'vsc85xx_probe': drivers/net/phy/mscc.c:460:45: error: '-mode' directive writing 5 bytes into a region of size between 0 and 9 [-Werror=format-overflow=] ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i); ^~~~~ drivers/net/phy/mscc.c:460:9: note: 'sprintf' output between 19 and 28 bytes into a destination of size 22 ret = sprintf(led_dt_prop, "vsc8531,led-%d-mode", i); ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~ While we can make a reasonable assumption that the number of LEDs is small, the cost of making the buffer a little bigger is insignificant as well. Fixes: 11bfdabb7ff5 ("net: phy: mscc: factorize code for LEDs mode") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Alexandre Belloni <alexandre.belloni@bootlin.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: ethernet: dpaa: remove unused variablesArnd Bergmann
The patch that removed the only users of the oldadv/newadv variables accidentally left the now-unused declarations behind: drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c: In function 'dpaa_set_pauseparam': drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:14: error: unused variable 'oldadv' [-Werror=unused-variable] drivers/net/ethernet/freescale/dpaa/dpaa_ethtool.c:185:6: error: unused variable 'newadv' [-Werror=unused-variable] Fixes: 70814e819c11 ("net: ethernet: Add helper for set_pauseparam for Asym Pause") Signed-off-by: Arnd Bergmann <arnd@arndb.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: aquantia: Make function aq_fw1x_set_power() staticWei Yongjun
Fixes the following sparse warning: drivers/net/ethernet/aquantia/atlantic/hw_atl/hw_atl_utils.c:873:5: warning: symbol 'aq_fw1x_set_power' was not declared. Should it be static? Fixes: a0da96c08cfa ("net: aquantia: implement WOL support") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net/tls: Make function get_rec() staticWei Yongjun
Fixes the following sparse warning: net/tls/tls_sw.c:655:16: warning: symbol 'get_rec' was not declared. Should it be static? Fixes: a42055e8d2c3 ("net/tls: Add support for async encryption of records for performance") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net/core: make function ___gnet_stats_copy_basic() staticWei Yongjun
Fixes the following sparse warning: net/core/gen_stats.c:166:1: warning: symbol '___gnet_stats_copy_basic' was not declared. Should it be static? Fixes: 5e111210a443 ("net/core: Add new basic hardware counter") Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Acked-by: Eelco Chaudron <echaudro@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-28net: xen-netback: fix return type of ndo_start_xmit functionYueHaibing
The method ndo_start_xmit() is defined as returning an 'netdev_tx_t', which is a typedef for an enum type, so make sure the implementation in this driver has returns 'netdev_tx_t' value, and change the function return type to netdev_tx_t. Found by coccinelle. Signed-off-by: YueHaibing <yuehaibing@huawei.com> Acked-by: Wei Liu <wei.liu2@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit (git 2.34.1) at 2025-09-12 07:54:27 +0000