| Age | Commit message (Collapse) | Author |
|---|
|
Declare pin for LSCO in stm32-pinctrl provider node to reserve this pin
for RTC OUT2_RMP, in stm32mp15-pinctrl.dtsi.
Signed-off-by: Valentin Caron <valentin.caron@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
DHCOR SoM DT
The STM32MP13xx DHCOR SoM is populated with M24256E EEPROM which has
Additional Write lockable page at separate I2C address. Describe the
page in DT to make it available.
Note that the WLP page on this device is hardware write-protected by
R37 which pulls the nWC signal high to VDD_3V3_1V8 power rail.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The IWDG2 is capable of generating pre-timeout interrupt, which can be used
to wake the system up from suspend to mem. Add the EXTI interrupt mapping
and mark the IWDG2 as wake up source.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The eMMC interface was configured to configure the FBCLK
into the Alt A setting, but this should be in GPIO mode
and available for use as a reset line. Move it to the new
mc_a_2 setting, and define this config in the generic
options.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241019-ux500-dts-updates-v1-2-a89bfbd0f680@linaro.org
|
|
The Codina Zinitix touchscreens have touchkeys for HOME and
BACK, add these now that the driver and bindings support it.
Cc: Nikita Travkin <nikita@trvn.ru>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Link: https://lore.kernel.org/r/20241019-ux500-dts-updates-v1-1-a89bfbd0f680@linaro.org
|
|
DHCOM PDK2
By default the SGTL5000 derives bit and frame clock from MCLK, which
does not produce particularly accurate results. The SGTL5000 PLL does
improve the accuracy, but also increases power consumption. Using the
SoC SAI interface as bit and frame clock source results in the best
accuracy without the power consumption increase downside. Switch the
bit and frame clock direction from SAI to SGTL5000, reduce mclk-fs to
match.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Switch the bitclock-master and frame-master properties from phandle to
flag on STM32MP15xx DHCOM PDK2. There is no real reason to use phandle
in this system DT, since the phandle points to the endpoint node which
contains the property itself. Simplify the DT. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Sort properties alphabetically in audio endpoints of STM32MP15xx
DHCOM PDK2 DT. No functional change.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Introduce device tree support for the MECIO1 and MECT1S board variants.
MECIO1 is an I/O and motor control board used in blood sample analysis
machines. MECT1S is a 1000Base-T1 switch for internal machine networks
of blood sample analysis machines.
Signed-off-by: David Jander <david@protonic.nl>
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Rename 'pins1' to 'pins' in the qspi_bk1_pins_a node to correct the
subnode name. The incorrect name caused the configuration to be
applied to the wrong subnode, resulting in QSPI not working properly.
Some additional changes was made:
- To avoid this kind of regression, all references to pin configuration
nodes are now referenced directly using the format &{label/subnode}.
- /delete-property/ bias-disable; was added everywhere where bias-pull-up
is used
- redundant properties like driver-push-pull are removed
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The RTL8211 PHY on DH STM32MP13xx DHCOR DHSBC carrier board supports HW
LED offload, the LEDs can be configured on link at 10/100/1000 line rate
and on RXTX activity. There are two PHYs on this board, each only has two
out of three LEDs connected to the PHY LED outputs. Describe this hardware
configuration in DT.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This enables DDR50 mode for the eMMC on Octavo OSD32MP1-RED board.
Fixes: be78ab4f632c ("ARM: dts: stm32: add initial support for stm32mp157-odyssey board")
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Reviewed-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
board
Describe ethernet MAC address nvmem cells in DH STM32MP13xx DHCOR DHSBC
board DT. The MAC address can be fused in BSEC OTP fuses and used to set
up MAC address for both ethernet MACs on this board.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
The RTL8211F PHY clock output is not used on DH STM32MP13xx DHCOR DHSBC
board, disable it to improve EMI characteristics.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
DHSBC board
The RTL8211F PHY gets confused when the MDIO bus lines get switched
to ANALOG during suspend/resume cycle. Keep the MDIO and MDC lines
in AF during suspend/resume to avoid confusing the PHY. The PHY can
be brought out of the confused state by restarting auto-negotiation
too, but that seems like an odd workaround and shouldn't be in the
PHY driver.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.11, round 1
Highlights:
----------
-MCU:
- Add syscfg missing clock on stm32f429.
- MPU:
- STM32MP13:
- Add camera support on stm32mp135f-dk bord using DCMIPP and
GC2145 sensor.
- Document PWM output for stm32mp135f-dk
- Add goodix touchscreen support on stm32mp135f-dk board.
- Add new DH DHCOR / DHSBC board (Som + carrier board) based on
STM32MP135F SoC.
SOM part contains: STM32MP135F SoC, 512MB DDR2L RAM and
eMMC/SDIO wifi module.
The carrier boards embedds 2 RGMII ETH ports, USB-A,USB-C
and an extansion connector.
- Add Ethernet controller support on stm32mp135f-dk.
It uses LAN8742A PHY based on RMII.
- STMP32MP15:
- Rework Octavo OSD32MP1 split for USB phy.
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- STM32MP25:
- Add OP-TEE IRQ for asynchronous notification support.
It allows OP-TEE to trig Linux.
- Enable firewall for RCC.
- Add all U(s)ART nodes for stm32mp25.
- Add 3 power domains for low power modes.
- Add HPDMA support.
- Add Ethernet controller (ETH2) support on stm32mp257f-ev1.
It uses Realtek PHY based on RGMII.
- Add and enable SCMI regulator support.
* tag 'stm32-dt-for-v6.11-1' of https://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32: (31 commits)
arm64: dts: st: describe power supplies for stm32mp257f-ev1 board
arm64: dts: st: add scmi regulators on stm32mp25
regulator: Add STM32MP25 regulator bindings
ARM: dts: stm32: omit unused pinctrl groups from stm32mp13 dtb files
arm64: dts: st: enable Ethernet2 on stm32mp257f-ev1 board
arm64: dts: st: add eth2 pinctrl entries in stm32mp25-pinctrl.dtsi
arm64: dts: st: add ethernet1 and ethernet2 support on stm32mp25
arm64: dts: st: add HPDMA nodes on stm32mp251
ARM: dts: stm32: Add ethernet support for DH STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: order stm32mp13-pinctrl nodes
ARM: dts: stm32: add ethernet1 for STM32MP135F-DK board
ARM: dts: stm32: add ethernet1/2 RMII pins for STM32MP13F-DK board
ARM: dts: stm32: add ethernet1 and ethernet2 support on stm32mp13
ARM: dts: stm32: Document output pins for PWMs on stm32mp135f-dk
ARM: dts: stm32: OP-TEE async notif interrupt for ST STM32MP15x boards
ARM: dts: stm32: Missing clocks for stm32f429's syscfg.
ARM: dts: stm32: Add support for STM32MP13xx DHCOR SoM and DHSBC board
ARM: dts: stm32: Add pinmux nodes for DH electronics STM32MP13xx DHCOR SoM and DHSBC board
dt-bindings: arm: stm32: Add compatible string for DH electronics STM32MP13xx DHCOR DHSBC board
ARM: dts: stm32: osd32: move pwr_regulators to common
...
Link: https://lore.kernel.org/r/8f10bd29-d067-4060-89ff-2e1a605f3141@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
stm32mp13-pinctrl.dtsi contains nearly all pinctrl groups collected from
all boards. Most of them end up unused by a board and only waste binary
space. Add /omit-if-no-ref/ to the groups to scrub the unused groups
from the dtbs.
Use the following regex to update the file and drop two useless newlines too:
s@^\t[^:]\+: [^ ]\+ {$@\t/omit-if-no-ref/\r&@
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add ethernet support for the DH STM32MP13xx DHCOR DHSBC carrier board.
This carrier board is populated with two gigabit ethernet ports and two
Realtek RTL8211F PHYs, both are described in this DT patch.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Keep alphabetic order for pins definition nodes for a better read.
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Ethernet1: RMII with crystal
Ethernet2: RMII with no cristal, need "phy-supply" property to work,
today this property was managed by Ethernet glue, but should be present
and managed in PHY node. So I will push second Ethernet in next step.
PHYs used are SMSC (LAN8742A)
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Those pins are used for Ethernet 1 and 2 on STM32MP13F-DK board.
ethernet1: RMII with crystal.
ethernet2: RMII without crystal.
Add analog gpio pin configuration ("sleep") to manage power mode on
stm32mp13.
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Reviewed-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Both instances ethernet based on GMAC SNPS IP on stm32mp13.
GMAC IP version is SNPS 4.20.
Signed-off-by: Christophe Roullier <christophe.roullier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
To simplify identifying the pins where the PWM output is routed to,
add a comment to each PWM device about the respective pin on the
expansion connector.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Define the GIC interrupt (PPI 15) to be used on ST STM32MP15x boards
for OP-TEE async notif.
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Without clock definition, SYSCFG will not work, EXTI interrupt for
port other than GPIOA will fail to operate.
Signed-off-by: Yanjun Yang <yangyj.ee@gmail.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This stm32mp135f-dhcor-dhsbc board is a stack of DHCOR SoM based on
STM32MP135F SoC (900MHz / crypto capabilities) populated on DHSBC
carrier board.
The SoM contains the following peripherals:
- STPMIC (power delivery)
- 512MB DDR3L memory
- eMMC and SDIO WiFi module
The DHSBC carrier board contains the following peripherals:
- Two RGMII Ethernet ports
- USB-A Host port, USB-C peripheral port, USB-C power supply plug
- Expansion connector
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
and DHSBC board
Add new pinmux nodes for DH electronics STM32MP13xx DHCOR SoM and DHSBC board.
The following pinmux nodes are added:
- ADC pins
- ADC CC pins
- ETH1 pins
- ETH2 pins
- I2C5 pins
- MCAN1 pins
- MCAN2 pins
- PWM13 pins
- PWM5 pins
- QSPI pins
- SAI1 pins
- SDMMC2 D4..D7 pins
- SPI2 pins
- SPI3 pins
- UART4 pins
- UART7 pins
- USART1 pins
- USART2 pins
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add a 'thermal-zones' node for stih418.
A thermal-zone needs three components:
- thermal sensors, described in an earlier commit[1]
- cooling devices, specified for each CPU
- a thermal zone, describing the overall behavior.
The thermal zone needs references to both CPUs and thermal sensors,
which phandle are also added. The thermal management will then be
achieved on CPUs using the cpufreq framework.
[1] https://lore.kernel.org/lkml/20240320-thermal-v3-2-700296694c4a@gmail.com/
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
"#thermal-sensor-cells" is required and missing in thermal nodes.
Add it.
Signed-off-by: Raphael Gallais-Pou <rgallaispou@gmail.com>
Reviewed-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
|
|
According to the OSD32MP1 Power System overview[1] pwr_regulators;
vdd-supply and vdd_3v3_usbfs-supply are hard-wired internally in
the SIP module to vdd and ldo4.
[1]:
https://octavosystems.com/app_notes/osd32mp1-power-system-overview/#connections
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
According to the OSD32MP1 Power System overview[1] usb phy power is
hard-wired internally in the SIP module to ldo4.
[1]:
https://octavosystems.com/app_notes/osd32mp1-power-system-overview/#connections
Signed-off-by: Sean Nyekjaer <sean@geanix.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
STM32MP15xx RM0436 Rev 6 section 46.3 System timer generator (STGEN) states
"
Arm recommends that the system counter is in an always-on power domain.
This is not supported in the current implementation, therefore STGEN should
be saved and restored before Standby mode entry, and restored at Standby
exit by secure software.
...
"
Instead of piling up workarounds in the firmware which is difficult to
update, add "arm,no-tick-in-suspend" DT property into the timer node to
indicate the timer is stopped in suspend, and let the kernel fix the
timer up.
Fixes: 8471a20253eb ("ARM: dts: stm32: add stm32mp157c initial support")
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Touchscreen reset needs to be configured
via the pinctrl not the driver (a pull-down resistor
has been soldered onto the reset line which forces
the touchscreen to reset state).
Interrupt line must have a pull-down resistor
in order to freeze the i2c address at 0x5D.
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
On STM32MP135F-DK board the camera support is made of the
CSI based GC2145 sensor, connected to the ST-MIPID02 CSI to parallel
bridge, connected to the DCMIPP parallel input.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Adds DCMIPP pinctrl support and assigns dedicated GPIO pins.
Signed-off-by: Alain Volmat <alain.volmat@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull interrupt subsystem updates from Thomas Gleixner:
"Core code:
- Interrupt storm detection for the lockup watchdog:
Lockups which are caused by interrupt storms are not easy to debug
because there is no information about the events which make the
lockup detector trigger.
To make this more user friendly, provide an extenstion to interrupt
statistics which allows to take snapshots and an interface to
retrieve the delta to the snapshot. Use this new mechanism in the
watchdog code to do a two stage lockup analysis by taking the
snapshot and printing the deltas for the topmost active interrupts
on the second trigger.
Note: This contains both the interrupt and the watchdog changes as
the latter depend on the former obviously.
- Avoid summation loops in the /proc/interrupts output and use the
global counter when possible
- Skip suspended interrupts on CPU hotplug operations to ensure that
they are not delivered before the system resumes the device drivers
when coming out of suspend.
- On CPU hot-unplug interrupts which are affine to the outgoing CPU
are migrated to a different CPU in the affinity mask. This can fail
when the CPUs have no vectors left. Instead of giving up try to
migrate it to any online CPU and thereby breaking the affinity
setting in order to prevent a stale device interrupt which targets
an offline CPU
- The usual small cleanups
Driver code:
- Support for the RISCV AIA MSI controller
- Make the interrupt allocation for the Loongson PCH controller more
flexible to prevent vector exhaustion
- The usual set of cleanups and fixes all over the place"
* tag 'irq-core-2024-05-12' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (51 commits)
irqchip/gic-v3-its: Remove BUG_ON in its_vpe_irq_domain_alloc
cpuidle: Avoid explicit cpumask allocation on stack
irqchip/sifive-plic: Avoid explicit cpumask allocation on stack
irqchip/riscv-aplic-direct: Avoid explicit cpumask allocation on stack
irqchip/loongson-eiointc: Avoid explicit cpumask allocation on stack
irqchip/gic-v3-its: Avoid explicit cpumask allocation on stack
irqchip/irq-bcm6345-l1: Avoid explicit cpumask allocation on stack
cpumask: Introduce cpumask_first_and_and()
irqchip/irq-brcmstb-l2: Avoid saving mask on shutdown
genirq: Reuse irq_is_nmi()
genirq/cpuhotplug: Retry with cpu_online_mask when migration fails
genirq/cpuhotplug: Skip suspended interrupts when restoring affinity
arm64: dts: st: Add interrupt parent to pinctrl on stm32mp251
arm64: dts: st: Add exti1 and exti2 nodes on stm32mp251
ARM: dts: stm32: List exti parent interrupts on stm32mp131
ARM: dts: stm32: List exti parent interrupts on stm32mp151
arm64: Kconfig.platforms: Enable STM32_EXTI for ARCH_STM32
irqchip/stm32-exti: Mark events reserved with RIF configuration check
irqchip/stm32-exti: Skip secure events
irqchip/stm32-exti: Convert driver to standard PM
...
|
|
Link panel and display controller.
Enable panel, backlight and display controller.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Adds LTDC pinctrl support and assigns dedicated GPIO pins.
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
STM32MP13x SoC family embeds a new version of LTDC (Liquid crystal
display - Thin film transistor) Display Controller.
It provides a parallel digital RGB (red, green, blue) and signals for
horizontal, vertical synchronization, pixel clock and data enable as
output to interface directly to a variety of LCD-TFT panels.
Main features
* 2 input layers blended together to compose the display
* Cropping of layers from any input size and location
* Multiple input pixel formats:
– Predefined ARGB, with 7 formats: ARGB8888, ABGR8888, RGBA8888,
BGRA8888, RGB565, BGR565, RGB888packed.
– Flexible ARGB, allowing any width and location for A,R,G,B
components.
– Predefined YUV, with 3 formats: YUV422-1L (FourCC: YUYV,
Interleaved), YUV420-2L (FourCC: NV12, semi planar), YUV420-3L
(FourCC: Yxx, full planar) with some flexibility on the sequence of
the component.
* Color look-up table (CLUT) up to 256 colors (256x24 bits) per layer
* Color transparency keying
* Composition with flexible window position and size versus output
display
* Blending with flexible layer order and alpha value (per pixel or
constant)
* Background underlying color
* Gamma with non-linear configurable table
* Dithering for output with less bits per component (pseudo-random on
2 bits)
* Polarity inversion for HSync, VSync, and DataEnable outputs
* Output as RGB888 24 bpp or YUV422 16 bpp
* Secure layer (using Layer2) capability, with grouped regs and
additional interrupt set
* Interrupts based on 7 different events
* AXI master interface with long efficient bursts (64 or 128 bytes)
Signed-off-by: Raphael Gallais-Pou <raphael.gallais-pou@foss.st.com>
Signed-off-by: Yannick Fertre <yannick.fertre@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
This patch adds STM32 PWR regulators DT support on stm32mp131.
This requires TFA to clear RCC_SECCFGR, is disabled by default
and can only be enabled on board DT level.
Signed-off-by: Marek Vasut <marex@denx.de>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Add heartbeat led for stm32mp157c-ed1.
Signed-off-by: Patrice Chotard <patrice.chotard@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
According to documents [1], [2] and [3], we have 2 CAN devices on the
stm32f746 platform and 3 on the stm32f769 platform. So let's move the
can3 node from stm32f746.dtsi to stm32f769.dtsi.
[1] https://www.st.com/en/microcontrollers-microprocessors/stm32f7-series.html
[2] RM0385: STM32F75xxx and STM32F74xxx advanced Arm®-based 32-bit MCUs
[3] RM0410: STM32F76xxx and STM32F77xxx advanced Arm®-based 32-bit MCUs
Fixes: df362914eead ("ARM: dts: stm32: re-add CAN support on stm32f746")
Signed-off-by: Dario Binacchi <dario.binacchi@amarulasolutions.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Reference ETZPC as an access-control-provider.
For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP13 reference manual
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and keep the "simple-bus" compatible for
backward compatibility.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Reference ETZPC as an access-control-provider.
For more information on which peripheral is securable or supports MCU
isolation, please read the STM32MP15 reference manual
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
ETZPC is a firewall controller. Put all peripherals filtered by the
ETZPC as ETZPC subnodes and keep the "simple-bus" compatible for
backward compatibility.
Signed-off-by: Gatien Chevallier <gatien.chevallier@foss.st.com>
Signed-off-by: Alexandre Torgue <alexandre.torgue@foss.st.com>
|
|
Stop using the table inside the EXTI driver and list in DT the mapping
between EXTI events and its parent interrupts.
By switching away from using the internal table, there is no need anymore
to use the specific compatible "st,stm32mp13-exti", which was introduced to
select the proper internal table.
Convert the driver's table for stm32mp131 to the DT property
interrupts-extended.
Switch the compatible string to the generic "st,stm32mp1-exti", in place of
the specific "st,stm32mp13-exti".
Older DT using compatible "st,stm32mp13-exti" will still work as the driver
remains backward compatible.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-10-antonio.borneo@foss.st.com
|
|
Stop using the table inside the EXTI driver and list in DT the mapping
between EXTI events and its parent interrupts.
Convert the driver's table for stm32mp151 to the DT property
interrupts-extended.
Signed-off-by: Antonio Borneo <antonio.borneo@foss.st.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Link: https://lore.kernel.org/r/20240415134926.1254428-9-antonio.borneo@foss.st.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32 into soc/dt
STM32 DT for v6.9, round 1
Highlights:
----------
- MCU:
- Add DSI support on stm32f769.
- Add display support on stm32f769-disco.
- Add stm32f769-disco-mb1166-reva09 board support which belongs to
the novatek NT35510 panel.
- MPU:
- STM32MP13:
- Add CRC support an enable it on stm32mp135f-dk.
- Enable CRYP on stm32mp135f-dk.
- STMP32MP15:
- Fix DSI peripheral clock: use bus clock instead of kernel clock
for pclk.
- LXA: driver powerboard lines as open drain.
- LXA: reduce RGMII drive strenght to reduce EMI emmissions.
- STM32MP25:
- Add video encoder / video decoder support.
* tag 'stm32-dt-for-v6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/atorgue/stm32:
arm64: dts: st: add video encoder support to stm32mp255
arm64: dts: st: add video decoder support to stm32mp255
ARM: dts: stm32: enable crypto accelerator on stm32mp135f-dk
ARM: dts: stm32: enable CRC on stm32mp135f-dk
ARM: dts: stm32: add CRC on stm32mp131
ARM: dts: add stm32f769-disco-mb1166-reva09
ARM: dts: stm32: add display support on stm32f769-disco
ARM: dts: stm32: rename mmc_vcard to vcc-3v3 on stm32f769-disco
ARM: dts: stm32: add DSI support on stm32f769
dt-bindings: mfd: stm32f7: Add binding definition for DSI
dt-bindings: nt35510: document 'port' property
ARM: dts: stm32: lxa-tac: reduce RGMII interface drive strength
ARM: dts: stm32: fix DSI peripheral clock on stm32mp15 boards
ARM: dts: stm32: lxa-tac: drive powerboard lines as open-drain
Link: https://lore.kernel.org/r/a7ae1058-e24d-4a6b-900f-401f0e3ae17c@foss.st.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt into soc/dt
Minor improvements in ARM DTS for v6.9
1. Marvell MMP2: Very old issue, for which I sent patch back in 2014.
Patch was never picked up and now another try to fix the same
happened, so here it goes: use proper compatible MAX8925.
2. Marvell Dove: add proper unit-addresses.
3. TI DA850: add MMC interrupts.
4. STI: minor white-space fixes.
* tag 'dt-cleanup-6.9' of https://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux-dt:
ARM: dts: sti: minor whitespace cleanup around '='
ARM: dts: da850: add MMD SDIO interrupts
ARM: dts: marvell: dove-cubox: fix si5351 node names
arm: dts: marvell: Fix maxium->maxim typo in brownstone dts
Link: https://lore.kernel.org/r/20240218182656.32103-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
