| Age | Commit message (Collapse) | Author |
|---|
|
Drop dmtimer usage for pulse timer in favor of hrtimer. That allows
removing PWM dmitimer platform data usage.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
With the upcoming removal of legacy boot, lets add support to one of the
last N900 drivers remaining without it. As the driver still uses omap
dmtimer, add auxdata as well.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Convert driver to use PWM framework instead of calling dmtimer functions
directly for PWM timer. Remove paragraph about writing to the Free Software
Foundation's mailing address while at it.
Signed-off-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Acked-by: Pali Rohár <pali.rohar@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Looks like I only partially fixed up things if CONFIG_SMP
is not set for the recent kexec changes. We don't have
boot_secondary available without SMP as reported by Arnd.
Fixes: 0573b957fc21 ("ARM: OMAP4+: Prevent CPU1 related hang with kexec")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Kexec needs omap4_cpu_kill, otherwise kexec will produce on SMP:
kexec_load failed: Invalid argument
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
We need to reset CPU1 properly for kexec when booting different
kernel versions. Otherwise CPU1 will attempt to boot the the
previous kernel's start_secondary(). Note that the restctrl
register is different from the low-power mode wakeup register
CPU1_WAKEUP_NS_PA_ADDR. We need to configure both.
Let's fix the issue by defining SoC specific data to initialize
things in a more generic way. And let's also standardize omap-smp.c
to use soc_is instead of cpu_is while at it.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Kexec booted kernels on omap4 will hang early during the boot if the
booted kernel is different version from the previous kernel.
This is because the previous kernel may have configured low-power mode
using CPU1_WAKEUP_NS_PA_ADDR. In that case it points to the previous
kernel's omap4_secondary_startup(), and CPU1 can be in low power mode
from the previous kernel. When the new kernel configures the CPU1
clockdomain, CPU1 can wake from low power state prematurely during
omap44xx_clockdomains_init() running random code.
Let's fix the issue by configuring CPU1_WAKEUP_NS_PA_ADDR before we
call omap44xx_clockdomains_init(). Note that this is very early during
the init, and we will do proper CPU1 reset during SMP init a bit later
on in omap4_smp_prepare_cpus(). And we need to do this when SMP is
not enabled as the previous kernel may have had it enabled.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Prepare things for making kexec work on SMP omap variants by initializing
SARM RAM base early. This allows us to configure CPU1 for kexec in case
the previous kernel has put CPU1 in low power mode.
Note that this should not prevent moving other SAR RAM code to live
under drivers. However for kexec, we will need this very early.
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Tested-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
As per the TRM: http://www.ti.com/lit/ug/spruh73m/spruh73m.pdf
offset 0x4 is reserved for PRM_PER. Hence removing the wrongly
defined address offset.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The ti81xx_rtc_hwmod is not exported, or declared outside the file
arch/arm/mach-omap2/omap_hwmod_81xx_data.c so make it static to
avoid the following warning:
arch/arm/mach-omap2/omap_hwmod_81xx_data.c:246:19: warning: symbol 'ti81xx_rtc_hwmod' was not declared. Should it be static?
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
pruss hwmod RSTST register wrongly points to PWRSTCTRL register in case of
am43xx. Fix the RSTST register offset value.
This can lead to setting of wrong power state values for PER domain.
Fixes: 1c7e224d ("ARM: OMAP2+: hwmod: AM335x: runtime register update")
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Fix dra7 for hardware issues limiting L4Per and L3init power domains
to on state. Without this the devices may not work correctly after
some time of use because of asymmetric aging. And related to this,
let's also remove the unusable states.
- Always select omap interconnect for am43x as otherwise the am43x
only configurations will not boot properly. This can happen easily
for any product kernels that leave out other SoCs to save memory.
- Fix DSS PLL2 addresses that have gone unused for now
- Select erratum 430973 for omap3, this is now safe to do and can
save quite a bit of debugging time for people who may have left
it out.
* tag 'omap-for-v4.7/fixes-powedomain' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_mem_ret
ARM: OMAP: DRA7: powerdomain data: Remove unused pwrsts_logic_ret
ARM: OMAP: DRA7: powerdomain data: Set L3init and L4per to ON
ARM: OMAP2+: Select OMAP_INTERCONNECT for SOC_AM43XX
ARM: dts: DRA74x: fix DSS PLL2 addresses
ARM: OMAP2: Enable Errata 430973 for OMAP3
+ Linux 4.7-rc2
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Fixes for omaps for v4.7-rc cycle:
- Two boot warning fixes from the RCU tree that should have gotten
merged several weeks ago already but did not because of issues
with who merges them. Paul has now split the RCU warning fixes into
sets for various maintainers.
- Fix ams-delta FIQ regression caused by omap1 sparse IRQ changes
- Fix PM for omap3 boards using timer12 and gptimer, like the
original beagleboard
- Fix hangs on am437x-sk-evm by lowering the I2C bus speed
* tag 'fixes-rcu-fiq-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: dts: am437x-sk-evm: Reduce i2c0 bus speed for tps65218
ARM: OMAP2+: timer: add probe for clocksources
ARM: OMAP1: fix ams-delta FIQ handler to work with sparse IRQ
arm: Use _rcuidle for smp_cross_call() tracepoints
arm: Use _rcuidle tracepoint to allow use from idle
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
A few platforms are currently missing clocksource_probe() completely
in their time_init functionality. On OMAP3430 for example, this is
causing cpuidle to be pretty much dead, as the counter32k is not
going to be registered and instead a gptimer is used as a clocksource.
This will tick in periodic mode, preventing any deeper idle states.
While here, also drop one unnecessary check for populated DT before
existing clocksource_probe() call.
Signed-off-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), with the exception of MPU power domain, all
other power domains do not have memories capable of retention since
they all operate in either "ON" or "OFF" mode. For these power states,
the retention state for memories are basically ignored by PRCM and does
not require to be programmed.
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), with the exception of MPU power domain (and
CPUx sub power domains), all other power domains can either operate
in "ON" mode OR in some cases, "OFF" mode. For these power states,
the logic retention state is basically ignored by PRCM and does not
require to be programmed.
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
As per the latest revision F of public TRM for DRA7/AM57xx SoCs
SPRUHZ6F[1] (April 2016), L4Per and L3init power domains now operate in
always "ON" mode due to asymmetric aging limitations. Update the same
[1] http://www.ti.com/lit/pdf/spruhz6
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The addresses for DSS are provided in the DT data, so they can be
removed from the hwmod.
Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
QSPI address space information is passed from device tree. Therefore
remove legacy way of passing address space via hwmod data.
Signed-off-by: Vignesh R <vigneshr@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The new pdata callback (force_ick_on) is now used by the driver and the old
callback related code can be removed.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. To prevent the iclk idling the driver expects to have pdata callback
to call. With this patch the callback is going to be set up for DT boot
also.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
McBSP2/3 module's sidetone module operates using the module's ICLK clock.
When the Sidetone is in use the interface clock of the module must not
idle. The new callback expects to receive the *clk of the module's ick and
not the id number of the McBSP. This will allow us more cleanups and going
to simplify the ICLK handling.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
The McBSPLP's sidetone main clock is the McBSPLP's ICLK, not FCLK as the
sidetone only receives the ICLK from the main McBSP module.
Since the McBSP and sidetone is using the very same clock from PRCM level
the sidetone must not have the prcm section to check the clock status since
the sidetone is only used when McBSP is already configured.
If two separate hwmods looking at the same bit and they would use
pm_runtime in nested way (as it must happen with McBSP and it's ST module)
the hwmod would warn, because the idlest will not match what it is expected
after enable/disable of the clocks.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Devices that utilize the OCP registers and/or PRCM registers and
register bit fields should be modeled using hwmod. Since eQEP, ePWM and
eCAP don't fall under this category, remove their hwmod entries.
Instead these clocks simply use the clock that is passed through by its
parent PWMSS. Therefore, PWMSS handles the clock for itself and its
subdevices.
Signed-off-by: Franklin S Cooper Jr <fcooper@ti.com>
Acked-by: Paul Walmsley <paul@pwsan.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Signed-off-by: Andrea Gelmini <andrea.gelmini@gelma.net>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
AM43XX SoCs make use of the omap_l3_noc driver so explicitly select
OMAP_INTERCONNECT in the Kconfig for SOC_AM43XX to ensure it always gets
enabled for AM43XX only builds.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Enable Erratum 430973 similar to commit 5c86c5339c56 ("ARM:
omap2plus_defconfig: Enable ARM erratum 430973 for omap3") - Since
multiple defconfigs can exist from various points of view (multi_v7,
omap2plus etc.. it is always better to enable the erratum from the
Kconfig selection point of view so that downstream kernels dont have
to rediscover this all over again.
Reported-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Two fixes for omaps for v4.7 merge window, one to enable
ARM errata for am437x, and the other to add ARM errtum
workaround for dra7.
AFAIK these both can wait for v4.7, we can then request them
for stable kernels as needed.
* tag 'omap-for-v4.7/fixes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: AM43XX: Enable fixes for Cortex-A9 errata
ARM: OMAP5 / DRA7: Introduce workaround for 801819
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This replaces:
- "select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB" as this can
now be selected directly.
- "select ARCH_WANT_OPTIONAL_GPIOLIB" with no dependency: GPIOLIB
is now selectable by everyone, so we need not declare our
intent to select it.
When ordering the symbols the following rationale was used:
if the selects were in alphabetical order, I moved select GPIOLIB
to be in alphabetical order, but if the selects were not
maintained in alphabetical order, I just replaced
"select ARCH_REQUIRE_GPIOLIB" with "select GPIOLIB".
Cc: Michael Büsch <m@bues.ch>
Cc: arm@kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Instead of the full omapdss internal header, include only the platform_data
header.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
The omap_display_init() is implemented in the mach-omap2/display.c so the
declaration should have been there as well.
Change the board files to include display.h to avoid build breakage at the
same time.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAP_DSS_VENC_TYPE_COMPOSITE is 0. There is no need to explicitly set the
connector_type.
This change is needed for the omapdss header cleanup.
Signed-off-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC platform updates from Arnd Bergmann:
"We get support for three new 32-bit SoC platforms this time.
The amount of changes in arch/arm for any of them is miniscule, as all
the interesting code is in device driver subsystems (irqchip, clk,
pinctrl, ...) these days. I'm listing them here, as the addition of
the Kconfig statement is the main relevant milestone for a new
platform. In each case, some drivers are are shared with existing
platforms, while other drivers are added for v4.7 as well, or come in
a later release.
- The Aspeed platform is probably the most interesting one, this is
what most whitebox servers use as their baseboard management
controller. We get support for the very common ast2400 and ast2500
SoCs. The OpenBMC project focuses on this chip, and the LWN
article about their ELC 2016 presentation at
https://lwn.net/Articles/683320/
triggered the submission, but the code comes from IBM's OpenPOWER
team rather than the team at Facebook. There are still a lot more
drivers that need to get added over time, and I hope both teams can
work together on that.
- OXNAS is an old platform for Network Attached Storage devices from
Oxford Semiconductor. There are models with ARM10 (!) and
ARM11MPCore cores, but for now, we only support the original ARM9
based versions. The product lineup was subsequently part of PLX,
Avago and now the new Broadcom Ltd.
https://wiki.openwrt.org/doc/hardware/soc/soc.oxnas
has some more information.
- V2M-MPS2 is a prototyping platform from ARM for their Cortex-M
cores and is related to the existing Realview / Versatile Express
lineup, but without MMU.
We now support various NOMMU platforms, so adding a new one is
fairly straightforward.
http://infocenter.arm.com/help/topic/com.arm.doc.100112_0100_03_en/
has detailed information about the platform.
Other noteworthy updates:
- Work on LPC32xx has resumed, and Vladimir Zapolskiy and Sylvain
Lemieux are now maintaining the platform.
This is an older ARM9 based platform from NXP (not Freescale), but
it remains in use in embedded markets.
- Kevin Hilman is now co-maintaining the Amlogic Meson platform for
both 32-bit and 64-bit ARM, and started contributing some patches.
- As is often the case, work on the OMAP platforms makes up the bulk
of the actual SoC code changes in arch/arm, but there isn't a lot
of that either"
* tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (42 commits)
MAINTAINERS: ARM/Amlogic: add co-maintainer, misc. updates
MAINTAINERS: add ARM/NXP LPC32XX SoC specific drivers to the section
MAINTAINERS: add new maintainers of NXP LPC32xx SoC
MAINTAINERS: move ARM/NXP LPC32xx record to ARM section
arm: Add Aspeed machine
ARM: lpc32xx: remove duplicate const on lpc32xx_auxdata_lookup
ARM: lpc32xx: remove leftovers of legacy clock source and provider drivers
ARM: lpc32xx: remove reboot header file
ARM: dove: Remove CLK_IS_ROOT
ARM: orion5x: Remove CLK_IS_ROOT
ARM: mv78xx0: Remove CLK_IS_ROOT
ARM: davinci: da850: use clk->set_parent for async3
ARM: davinci: Move clock init after ioremap.
MAINTAINERS: Update ARM Versatile Express platform entry
ARM: vexpress/mps2: introduce MPS2 platform
MAINTAINERS: add maintainer entry for ARM/OXNAS platform
ARM: Add new mach-oxnas
irqchip: versatile-fpga: add new compatible for OX810SE SoC
ARM: uniphier: correct the call order of of_node_put()
MAINTAINERS: fix stale TI DaVinci entries
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC cleanups and fixes from Arnd Bergmann:
"Traditionally we've had two separate branches for cleanups and
non-critical bug fixes, but both of these got smaller with each
release and the differences are rather unclear now, so it seems more
appropriate to have a combined branch.
The most notable change is for OMAP, which gets a small rework to
simplify handling of the AUXDATA mechanism used on machines that are
not completely DT based yet, along with other work that is used as
preparation for dropping the legacy board files"
* tag 'armsoc-cleanups-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: Add interrupt line to MAX8997 PMIC on exynos4210-trats
ARM: dts: exynos: Fix regulator name to avoid forbidden character on exynos4210-trats
ARM: dts: exynos: Add MFC memory banks for Peach boards
ARM: OMAP2+: n900 needs MMC slot names for legacy user space
ARM: OMAP2+: Add more functions to pwm pdata for ir-rx51
ARM: debug: remove extraneous DEBUG_HI3716_UART option
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
ARM: davinci: use IRQCHIP_DECLARE for cp_intc
ARM: davinci: remove unused DA8XX_NUM_UARTS
ARM: davinci: simplify call to of populate
ARM: DaVinci USB: removed deprecated properties from MUSB config
ARM: rockchip: Fix use of plain integer as NULL pointer
ARM: realview: hide unused 'pmu_device' object
soc: versatile: dynamically detect RealView HBI numbers
|
|
* pm-cpufreq: (63 commits)
intel_pstate: Clean up get_target_pstate_use_performance()
intel_pstate: Use sample.core_avg_perf in get_avg_pstate()
intel_pstate: Clarify average performance computation
intel_pstate: Avoid unnecessary synchronize_sched() during initialization
cpufreq: schedutil: Make default depend on CONFIG_SMP
cpufreq: powernv: del_timer_sync when global and local pstate are equal
cpufreq: powernv: Move smp_call_function_any() out of irq safe block
intel_pstate: Clean up intel_pstate_get()
cpufreq: schedutil: Make it depend on CONFIG_SMP
cpufreq: governor: Fix handling of special cases in dbs_update()
cpufreq: intel_pstate: Ignore _PPC processing under HWP
cpufreq: arm_big_little: use generic OPP functions for {init, free}_opp_table
cpufreq: tango: Use generic platdev driver
cpufreq: Fix GOV_LIMITS handling for the userspace governor
cpufreq: mvebu: Move cpufreq code into drivers/cpufreq/
cpufreq: dt: Kill platform-data
mvebu: Use dev_pm_opp_set_sharing_cpus() to mark OPP tables as shared
cpufreq: dt: Identify cpu-sharing for platforms without operating-points-v2
cpufreq: governor: Change confusing struct field and variable names
cpufreq: intel_pstate: Enable PPC enforcement for servers
...
|
|
This patch explicitly enables the fixes for the below errata applicable
for AM43x Socs as was done for OMAP4.
754322: Faulty MMU translations following ASID switch
775420: A data cache maintenance operation which aborts,
followed by an ISB, without any DSB in-between,
might lead to deadlock
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Add workaround for Cortex-A15 ARM erratum 801819 which says in summary
that "A livelock can occur in the L2 cache arbitration that might
prevent a snoop from completing. Under certain conditions this can
cause the system to deadlock. "
Recommended workaround is as follows:
Do both of the following:
1) Do not use the write-back no-allocate memory type.
2) Do not issue write-back cacheable stores at any time when the cache
is disabled (SCTLR.C=0) and the MMU is enabled (SCTLR.M=1). Because it
is implementation defined whether cacheable stores update the cache when
the cache is disabled it is not expected that any portable code will
execute cacheable stores when the cache is disabled.
For implementations of Cortex-A15 configured without the “L2 arbitration
register slice” option (typically one or two core systems), you must
also do the following:
3) Disable write-streaming in each CPU by setting ACTLR[28:25] = 0b1111
So, we provide an option to disable write streaming on OMAP5 and DRA7.
It is a rare condition to occur and may be enabled selectively based
on platform acceptance of risk.
Applies to: A15 revisions r2p0, r2p1, r2p2, r2p3 or r2p4 and REVIDR[3]
is set to 0.
Based on ARM errata Document revision 18.0 (22 Nov 2013)
Note: the configuration for the workaround needs to be done with
each CPU bringup, since CPU0 bringup is done by bootloader, it is
recommended to have the workaround in the bootloader, kernel also does
ensure that CPU0 has the workaround and makes the workaround active
when CPU1 gets active.
With CONFIG_SMP disabled, it is expected to be done by the bootloader.
This does show significant degradation in synthetic tests such as
mbw (https://packages.qa.debian.org/m/mbw.html)
mbw -n 100 100|grep AVG (on a test platform)
Without enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13406 MiB: 100.00000 Copy: 745.913 MiB/s
AVG Method: DUMB Elapsed: 0.06746 MiB: 100.00000 Copy: 1482.357 MiB/s
AVG Method: MCBLOCK Elapsed: 0.03058 MiB: 100.00000 Copy: 3270.569 MiB/s
After enabling the erratum:
AVG Method: MEMCPY Elapsed: 0.13757 MiB: 100.00000 Copy: 726.913 MiB/s
AVG Method: DUMB Elapsed: 0.12024 MiB: 100.00000 Copy: 831.668 MiB/s
AVG Method: MCBLOCK Elapsed: 0.09243 MiB: 100.00000 Copy: 1081.942 MiB/s
Most benchmarks are designed for specific performance analysis, so
overall usecase must be considered before making a decision to
enable/disable the erratum workaround.
Pending internal investigation, the erratum is kept disabled by default.
Cc: Russell King <rmk+kernel@arm.linux.org.uk>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Tony Lindgren <tony@atomide.com>
Suggested-by: Richard Woodruff <r-woodruff2@ti.com>
Suggested-by: Brad Griffis <bgriffis@ti.com>
Signed-off-by: Nishanth Menon <nm@ti.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into next/fixes-non-critical
Merge "non urgent auxdata fix for v4.7 merge window" from Tony Lindgren:
Device tree auxdata handling fix that allows a match based on the
compatible string if no exact match based on the IO address is found.
This leaves out the need to patch auxdata for each driver when adding
new SoCs. And it also reprotedly fixes the issue of passing auxdata
to a child if the parent instantiates the child from DT as discussed
in the "[PATCH] of/platform: Allow secondary compatible match in
of_dev_lookup" mailing list thread.
As a minimal use case, let's also convert omap pinctrl auxdatato
use a generic match.
There is no need to get this in to the v4.6-rc cycle and it can wait
for v4.7 merge window. Note that these changes have now been sitting
in Linux next for about two weeks so far as I wanted to make sure no
new issues are popping up.
* tag 'omap-for-v4.7/auxdata-signed' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP2+: Simplify auxdata by using the generic match
of/platform: Allow secondary compatible match in of_dev_lookup
|
|
Testing on ARM encountered the following pair of lockdep-RCU splats:
------------------------------------------------------------------------
===============================
[ INFO: suspicious RCU usage. ]
4.6.0-rc4-next-20160422 #1 Not tainted
-------------------------------
include/trace/events/power.h:328 suspicious rcu_dereference_check() usage!
other info that might help us debug this:
RCU used illegally from idle CPU!
rcu_scheduler_active = 1, debug_locks = 0
RCU used illegally from extended quiescent state!
no locks held by swapper/0/0.
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.6.0-rc4-next-20160422 #1
Hardware name: Generic OMAP3-GP (Flattened Device Tree)
[<c010f55c>] (unwind_backtrace) from [<c010b64c>] (show_stack+0x10/0x14)
[<c010b64c>] (show_stack) from [<c047acbc>] (dump_stack+0xa8/0xe0)
[<c047acbc>] (dump_stack) from [<c012bc10>] (pwrdm_set_next_pwrst+0xf8/0x1cc)
[<c012bc10>] (pwrdm_set_next_pwrst) from [<c01269fc>] (omap3_enter_idle_bm+0x1b8/0x1e8)
[<c01269fc>] (omap3_enter_idle_bm) from [<c05fa0b8>] (cpuidle_enter_state+0x84/0x408)
[<c05fa0b8>] (cpuidle_enter_state) from [<c0182c1c>] (cpu_startup_entry+0x1c8/0x3f0)
[<c0182c1c>] (cpu_startup_entry) from [<c0b00c20>] (start_kernel+0x354/0x3cc)
------------------------------------------------------------------------
[<c010f55c>] (unwind_backtrace) from [<c010b64c>] (show_stack+0x10/0x14)
[<c010b64c>] (show_stack) from [<c047ac3c>] (dump_stack+0xa8/0xe0)
[<c047ac3c>] (dump_stack) from [<c012c340>] (_pwrdm_state_switch+0x188/0x32c)
[<c012c340>] (_pwrdm_state_switch) from [<c012c4f0>] (_pwrdm_post_transition_cb+0xc/0x14)
[<c012c4f0>] (_pwrdm_post_transition_cb) from [<c012ba74>] (pwrdm_for_each+0x30/0x5c)
[<c012ba74>] (pwrdm_for_each) from [<c012c72c>] (pwrdm_post_transition+0x24/0x30)
[<c012c72c>] (pwrdm_post_transition) from [<c012548c>] (omap_sram_idle+0xfc/0x240)
[<c012548c>] (omap_sram_idle) from [<c0126934>] (omap3_enter_idle_bm+0xf0/0x1e8)
[<c0126934>] (omap3_enter_idle_bm) from [<c05fa038>] (cpuidle_enter_state+0x84/0x408)
[<c05fa038>] (cpuidle_enter_state) from [<c0182b90>] (cpu_startup_entry+0x1c8/0x3f0)
[<c0182b90>] (cpu_startup_entry) from [<c0b00c20>] (start_kernel+0x354/0x3cc)
------------------------------------------------------------------------
These are caused by event tracing from the idle loop, and they were
exposed by commit 293e2421fe25 ("rcu: Remove superfluous versions of
rcu_read_lock_sched_held()"), which suppressed some false negatives.
The current commit therefore adds the _rcuidle suffix to make RCU aware
of this implicit use of RCU by event tracing, thus preventing both splats.
Reported-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Paul E. McKenney <paulmck@linux.vnet.ibm.com>
Tested-by: Guenter Roeck <linux@roeck-us.net>
Tested-by: Tony Lindgren <tony@atomide.com>
Cc: Russell King <linux@arm.linux.org.uk>
Reviewed-by: Steven Rostedt <rostedt@goodmis.org>
Cc: <linux-omap@vger.kernel.org>
Cc: <linux-arm-kernel@lists.infradead.org>
|
|
Let's pass the slot names in pdata like the legacy code does.
Once we have a generic DT binding for the slot names we can
switch to that.
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
Before we start removing omap3 legacy booting support, let's make n900
DT booting behave the same way for ir-rx51 as the legacy booting does.
For now, we need to pass pdata to the ir-rx51 driver. This means that
the n900 tree can move to using DT based booting without having to carry
all the legacy platform data with it when it gets dropped from the mainline
tree.
Note that the ir-rx51 driver is currently disabled because of the
dependency to !ARCH_MULTIPLATFORM. This will get sorted out later
with the help of drivers/pwm/pwm-omap-dmtimer.c. But first we need
to add chained IRQ support to dmtimer code to avoid introducing new
custom frameworks.
So let's just pass the necessary dmtimer functions to ir-rx51 so we
can get it working in the following patch.
Cc: Neil Armstrong <narmstrong@baylibre.com>
Tested-by: Ivaylo Dimitrov <ivo.g.dimitrov.75@gmail.com>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
|
|
The cpufreq-dt-platdev driver supports creation of cpufreq-dt platform
device now, reuse that and remove similar code from platform code.
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap into fixes
Merge "omap fixes for v4.6-rc cycle" from Tony Lindgren:
Fixes for omaps for v4.6-rc cycle:
- Clockdomain fix for dra7 timer interrupts
- Two fixes for GPMC EDMA binding, I missed the need for a merge with
GPMC changes and EDMA changes
- Fix beagle-x15 eSATA by dropping misconfigured extcon_usb1
- Fix occasional external aborts on 36xx with PM that we've been
chasing for past few months. It turned out to be duplicate restore
of INTC registers that can in some cases cause us to hit erratum 1.106.
* tag 'omap-for-v4.6/fixes-rc3' of git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap:
ARM: OMAP3: Fix external abort on 36xx waking from off mode idle
ARM: dts: am57xx-beagle-x15: remove extcon_usb1
ARM: dts: am437x: Fix GPMC dma properties
ARM: dts: am33xx: Fix GPMC dma properties
ARM: DRA7: clockdomain: Implement timer workaround for errata i874
|
