| Age | Commit message (Collapse) | Author |
|---|
|
In contrast to the commit message of the fixed commit VFs whose parent
PF is not configured are not always isolated, that is put on their own
PCI domain. This is because for VFs to be added to an existing PCI
domain it is enough for that PCI domain to share the same topology ID or
PCHID. Such a matching PCI domain without a parent PF may exist when
a PF from the same PCI card created the domain with the VF being a child
of a different, non accessible, PF. While not causing technical issues
it makes the rules which VFs are isolated inconsistent.
Fix this by explicitly checking that the parent PF exists on the PCI
domain determined by the topology ID or PCHID before registering the VF.
This works because a parent PF which is under control of this Linux
instance must be enabled and configured at the point where its child VFs
appear because otherwise SR-IOV could not have been enabled on the
parent.
Fixes: 25f39d3dcb48 ("s390/pci: Ignore RID for isolated VFs")
Cc: stable@vger.kernel.org
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
This creates a new zpci_iov_find_parent_pf() function which a future
commit can use to find if a VF has a configured parent PF. Use
zdev->rid instead of zdev->devfn such that the new function can be used
before it has been decided if the RID will be exposed and zdev->devfn is
set. Also handle the hypotheical case that the RID is not available but
there is an otherwise matching zbus.
Fixes: 25f39d3dcb48 ("s390/pci: Ignore RID for isolated VFs")
Cc: stable@vger.kernel.org
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Since commit 25f39d3dcb48 ("s390/pci: Ignore RID for isolated VFs") PFs
which are not initially configured but in standby are considered
isolated. That is they create only a single function PCI domain. Due to
the PCI domains being created on discovery, this means that even if they
are configured later on, sibling PFs and their child VFs will not be
added to their PCI domain breaking SR-IOV expectations.
The reason the referenced commit ignored standby PFs for the creation of
multi-function PCI subhierarchies, was to work around a PCI domain
renumbering scenario on reboot. The renumbering would occur after
removing a previously in standby PF, whose domain number is used for its
configured sibling PFs and their child VFs, but which itself remained in
standby. When this is followed by a reboot, the sibling PF is used
instead to determine the PCI domain number of it and its child VFs.
In principle it is not possible to know which standby PFs will be
configured later and which may be removed. The PCI domain and root bus
are pre-requisites for hotplug slots so the decision of which functions
belong to which domain can not be postponed. With the renumbering
occurring only in rare circumstances and being generally benign, accept
it as an oddity and fix SR-IOV for initially standby PFs simply by
allowing them to create PCI domains.
Cc: stable@vger.kernel.org
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Fixes: 25f39d3dcb48 ("s390/pci: Ignore RID for isolated VFs")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
The sysfs core now allows instances of 'struct bin_attribute' to be
moved into read-only memory. Make use of that to protect them against
accidental or malicious modifications.
Signed-off-by: Thomas Weißschuh <linux@weissschuh.net>
Acked-by: Alexander Gordeev <agordeev@linux.ibm.com>
Link: https://lore.kernel.org/r/20241211-sysfs-const-bin_attr-s390-v1-3-be01f66bfcf7@weissschuh.net
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Using the newly introduced debug_dump() mechanism add formatted content
of pci_debug_msg_id to the PCI report. The formatting is based on the
existing sprintf format but removes caller pointer and area index and
adds an column header. This will allow the platform to collect this log
data together with hardware errors. This sets the reverse flag such that
the newest log entries get added to the PCI report even if not all debug
log entries fit.
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Co-developed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Add a mechanism with which the status of PCI error recovery runs
is reported to the platform. Together with the status supply additional
information that may aid in problem determination.
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull more s390 updates from Heiko Carstens:
- Add swap entry for hugetlbfs support
- Add PTE_MARKER support for hugetlbs mappings; this fixes a regression
(possible page fault loop) which was introduced when support for
UFFDIO_POISON for hugetlbfs was added
- Add ARCH_HAS_PREEMPT_LAZY and PREEMPT_DYNAMIC support
- Mark IRQ entries in entry code, so that stack tracers can filter out
the non-IRQ parts of stack traces. This fixes stack depot capacity
limit warnings, since without filtering the number of unique stack
traces is huge
- In PCI code fix leak of struct zpci_dev object, and fix potential
double remove of hotplug slot
- Fix pagefault_disable() / pagefault_enable() unbalance in
arch_stack_user_walk_common()
- A couple of inline assembly optimizations, more cmpxchg() to
try_cmpxchg() conversions, and removal of usages of xchg() and
cmpxchg() on one and two byte memory areas
- Various other small improvements and cleanups
* tag 's390-6.13-2' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (27 commits)
Revert "s390/mm: Allow large pages for KASAN shadow mapping"
s390/spinlock: Use flag output constraint for arch_cmpxchg_niai8()
s390/spinlock: Use R constraint for arch_load_niai4()
s390/spinlock: Generate shorter code for arch_spin_unlock()
s390/spinlock: Remove condition code clobber from arch_spin_unlock()
s390/spinlock: Use symbolic names in inline assemblies
s390: Support PREEMPT_DYNAMIC
s390/pci: Fix potential double remove of hotplug slot
s390/pci: Fix leak of struct zpci_dev when zpci_add_device() fails
s390/mm/hugetlbfs: Add missing includes
s390/mm: Add PTE_MARKER support for hugetlbfs mappings
s390/mm: Introduce region-third and segment table swap entries
s390/mm: Introduce region-third and segment table entry present bits
s390/mm: Rearrange region-third and segment table entry SW bits
KVM: s390: Increase size of union sca_utility to four bytes
KVM: s390: Remove one byte cmpxchg() usage
KVM: s390: Use try_cmpxchg() instead of cmpxchg() loops
s390/ap: Replace xchg() with WRITE_ONCE()
s390/mm: Allow large pages for KASAN shadow mapping
s390: Add ARCH_HAS_PREEMPT_LAZY support
...
|
|
In commit 6ee600bfbe0f ("s390/pci: remove hotplug slot when releasing the
device") the zpci_exit_slot() was moved from zpci_device_reserved() to
zpci_release_device() with the intention of keeping the hotplug slot
around until the device is actually removed.
Now zpci_release_device() is only called once all references are
dropped. Since the zPCI subsystem only drops its reference once the
device is in the reserved state it follows that zpci_release_device()
must only deal with devices in the reserved state. Despite that it
contains code to tear down from both configured and standby state. For
the standby case this already includes the removal of the hotplug slot
so would cause a double removal if a device was ever removed in
either configured or standby state.
Instead of causing a potential double removal in a case that should
never happen explicitly WARN_ON() if a device in non-reserved state is
released and get rid of the dead code cases.
Fixes: 6ee600bfbe0f ("s390/pci: remove hotplug slot when releasing the device")
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Tested-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Prior to commit 0467cdde8c43 ("s390/pci: Sort PCI functions prior to
creating virtual busses") the IOMMU was initialized and the device was
registered as part of zpci_create_device() with the struct zpci_dev
freed if either resulted in an error. With that commit this was moved
into a separate function called zpci_add_device().
While this new function logs when adding failed, it expects the caller
not to use and to free the struct zpci_dev on error. This difference
between it and zpci_create_device() was missed while changing the
callers and the incompletely initialized struct zpci_dev may get used in
zpci_scan_configured_device in the error path. This then leads to
a crash due to the device not being registered with the zbus. It was
also not freed in this case. Fix this by handling the error return of
zpci_add_device(). Since in this case the zdev was not added to the
zpci_list it can simply be discarded and freed. Also make this more
explicit by moving the kref_init() into zpci_add_device() and document
that zpci_zdev_get()/zpci_zdev_put() must be used after adding.
Cc: stable@vger.kernel.org
Fixes: 0467cdde8c43 ("s390/pci: Sort PCI functions prior to creating virtual busses")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull PCI updates from Bjorn Helgaas:
"Enumeration:
- Make pci_stop_dev() and pci_destroy_dev() safe so concurrent
callers can't stop a device multiple times, even as we migrate from
the global pci_rescan_remove_lock to finer-grained locking (Keith
Busch)
- Improve pci_walk_bus() implementation by making it recursive and
moving locking up to avoid need for a 'locked' parameter (Keith
Busch)
- Unexport pci_walk_bus_locked(), which is only used internally by
the PCI core (Keith Busch)
- Detect some Thunderbolt chips that are built-in and hence
'trustworthy' by a heuristic since the 'ExternalFacingPort' and
'usb4-host-interface' ACPI properties are not quite enough (Esther
Shimanovich)
Resource management:
- Use PCI bus addresses (not CPU addresses) in 'ranges' properties
when building dynamic DT nodes so systems where PCI and CPU
addresses differ work correctly (Andrea della Porta)
- Tidy resource sizing and assignment with helpers to reduce
redundancy (Ilpo Järvinen)
- Improve pdev_sort_resources() 'bogus alignment' warning to be more
specific (Ilpo Järvinen)
Driver binding:
- Convert driver .remove_new() callbacks to .remove() again to finish
the conversion from returning 'int' to being 'void' (Sergio
Paracuellos)
- Export pcim_request_all_regions(), a managed interface to request
all BARs (Philipp Stanner)
- Replace pcim_iomap_regions_request_all() with
pcim_request_all_regions(), and pcim_iomap_table()[n] with
pcim_iomap(n), in the following drivers: ahci, crypto qat, crypto
octeontx2, intel_th, iwlwifi, ntb idt, serial rp2, ALSA korg1212
(Philipp Stanner)
- Remove the now unused pcim_iomap_regions_request_all() (Philipp
Stanner)
- Export pcim_iounmap_region(), a managed interface to unmap and
release a PCI BAR (Philipp Stanner)
- Replace pcim_iomap_regions(mask) with pcim_iomap_region(n), and
pcim_iounmap_regions(mask) with pcim_iounmap_region(n), in the
following drivers: fpga dfl-pci, block mtip32xx, gpio-merrifield,
cavium (Philipp Stanner)
Error handling:
- Add sysfs 'reset_subordinate' to reset the entire hierarchy below a
bridge; previously Secondary Bus Reset could only be used when
there was a single device below a bridge (Keith Busch)
- Warn if we reset a running device where the driver didn't register
pci_error_handlers notification callbacks (Keith Busch)
ASPM:
- Disable ASPM L1 before touching L1 PM Substates to follow the spec
closer and avoid a CPU load timeout on some platforms (Ajay
Agarwal)
- Set devices below Intel VMD to D0 before enabling ASPM L1 Substates
as required per spec for all L1 Substates changes (Jian-Hong Pan)
Power management:
- Enable starfive controller runtime PM before probing host bridge
(Mayank Rana)
- Enable runtime power management for host bridges (Krishna chaitanya
chundru)
Power control:
- Use of_platform_device_create() instead of of_platform_populate()
to create pwrctl platform devices so we can control it based on the
child nodes (Manivannan Sadhasivam)
- Create pwrctrl platform devices only if there's a relevant power
supply property (Manivannan Sadhasivam)
- Add device link from the pwrctl supplier to the PCI dev to ensure
pwrctl drivers are probed before the PCI dev driver; this avoids a
race where pwrctl could change device power state while the PCI
driver was active (Manivannan Sadhasivam)
- Find pwrctl device for removal with of_find_device_by_node()
instead of searching all children of the parent (Manivannan
Sadhasivam)
- Rename 'pwrctl' to 'pwrctrl' to match new bandwidth controller
('bwctrl') and hotplug files (Bjorn Helgaas)
Bandwidth control:
- Add read/modify/write locking for Link Control 2, which is used to
manage Link speed (Ilpo Järvinen)
- Extract Link Bandwidth Management Status check into
pcie_lbms_seen(), where it can be shared between the bandwidth
controller and quirks that use it to help retrain failed links
(Ilpo Järvinen)
- Re-add Link Bandwidth notification support with updates to address
the reasons it was previously reverted (Alexandru Gagniuc, Ilpo
Järvinen)
- Add pcie_set_target_speed() and related functionality so drivers
can manage PCIe Link speed based on thermal or other constraints
(Ilpo Järvinen)
- Add a thermal cooling driver to throttle PCIe Links via the
existing thermal management framework (Ilpo Järvinen)
- Add a userspace selftest for the PCIe bandwidth controller (Ilpo
Järvinen)
PCI device hotplug:
- Add hotplug controller driver for Marvell OCTEON multi-function
device where function 0 has a management console interface to
enable/disable and provision various personalities for the other
functions (Shijith Thotton)
- Retain a reference to the pci_bus for the lifetime of a pci_slot to
avoid a use-after-free when the thunderbolt driver resets USB4 host
routers on boot, causing hotplug remove/add of downstream docks or
other devices (Lukas Wunner)
- Remove unused cpcihp struct cpci_hp_controller_ops.hardware_test
(Guilherme Giacomo Simoes)
- Remove unused cpqphp struct ctrl_dbg.ctrl (Christophe JAILLET)
- Use pci_bus_read_dev_vendor_id() instead of hand-coded presence
detection in cpqphp (Ilpo Järvinen)
- Simplify cpqphp enumeration, which is already simple-minded and
doesn't handle devices below hot-added bridges (Ilpo Järvinen)
Virtualization:
- Add ACS quirk for Wangxun FF5xxx NICs, which don't advertise an ACS
capability but do isolate functions as though PCI_ACS_RR and
PCI_ACS_CR were set, so the functions can be in independent IOMMU
groups (Mengyuan Lou)
TLP Processing Hints (TPH):
- Add and document TLP Processing Hints (TPH) support so drivers can
enable and disable TPH and the kernel can save/restore TPH
configuration (Wei Huang)
- Add TPH Steering Tag support so drivers can retrieve Steering Tag
values associated with specific CPUs via an ACPI _DSM to improve
performance by directing DMA writes closer to their consumers (Wei
Huang)
Data Object Exchange (DOE):
- Wait up to 1 second for DOE Busy bit to clear before writing a
request to the mailbox to avoid failures if the mailbox is still
busy from a previous transfer (Gregory Price)
Endpoint framework:
- Skip attempts to allocate from endpoint controller memory window if
the requested size is larger than the window (Damien Le Moal)
- Add and document pci_epc_mem_map() and pci_epc_mem_unmap() to
handle controller-specific size and alignment constraints, and add
test cases to the endpoint test driver (Damien Le Moal)
- Implement dwc pci_epc_ops.align_addr() so pci_epc_mem_map() can
observe DWC-specific alignment requirements (Damien Le Moal)
- Synchronously cancel command handler work in endpoint test before
cleaning up DMA and BARs (Damien Le Moal)
- Respect endpoint page size in dw_pcie_ep_align_addr() (Niklas
Cassel)
- Use dw_pcie_ep_align_addr() in dw_pcie_ep_raise_msi_irq() and
dw_pcie_ep_raise_msix_irq() instead of open coding the equivalent
(Niklas Cassel)
- Avoid NULL dereference if Modem Host Interface Endpoint lacks
'mmio' DT property (Zhongqiu Han)
- Release PCI domain ID of Endpoint controller parent (not controller
itself) and before unregistering the controller, to avoid
use-after-free (Zijun Hu)
- Clear secondary (not primary) EPC in pci_epc_remove_epf() when
removing the secondary controller associated with an NTB (Zijun Hu)
Cadence PCIe controller driver:
- Lower severity of 'phy-names' message (Bartosz Wawrzyniak)
Freescale i.MX6 PCIe controller driver:
- Fix suspend/resume support on i.MX6QDL, which has a hardware
erratum that prevents use of L2 (Stefan Eichenberger)
Intel VMD host bridge driver:
- Add 0xb60b and 0xb06f Device IDs for client SKUs (Nirmal Patel)
MediaTek PCIe Gen3 controller driver:
- Update mediatek-gen3 DT binding to require the exact number of
clocks for each SoC (Fei Shao)
- Add support for DT 'max-link-speed' and 'num-lanes' properties to
restrict the link speed and width (AngeloGioacchino Del Regno)
Microchip PolarFlare PCIe controller driver:
- Add DT and driver support for using either of the two PolarFire
Root Ports (Conor Dooley)
NVIDIA Tegra194 PCIe controller driver:
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
Qualcomm PCIe controller driver:
- Add qcom SAR2130P DT binding with an additional clock (Dmitry
Baryshkov)
- Enable MSI interrupts if 'global' IRQ is supported, since a
previous commit unintentionally masked them (Manivannan Sadhasivam)
- Move endpoint controller cleanups that depend on refclk from the
host to the notifier that tells us the host has deasserted PERST#,
when refclk should be valid (Manivannan Sadhasivam)
- Add DT binding and driver support for IPQ9574, with Synopsys IP
v5.80a and Qcom IP 1.27.0 (devi priya)
- Move the OPP "operating-points-v2" table from the
qcom,pcie-sm8450.yaml DT binding to qcom,pcie-common.yaml, where it
can be used by other Qcom platforms (Qiang Yu)
- Add 'global' SPI interrupt for events like link-up, link-down to
qcom,pcie-x1e80100 DT binding so we can start enumeration when the
link comes up (Qiang Yu)
- Disable ASPM L0s for qcom,pcie-x1e80100 since the PHY is not tuned
to support this (Qiang Yu)
- Add ops_1_21_0 for SC8280X family SoC, which doesn't use the
'iommu-map' DT property and doesn't need BDF-to-SID translation
(Qiang Yu)
Rockchip PCIe controller driver:
- Define ROCKCHIP_PCIE_AT_SIZE_ALIGN to replace magic 256 endpoint
.align value (Damien Le Moal)
- When unmapping an endpoint window, compute the region index instead
of searching for it, and verify that the address was mapped (Damien
Le Moal)
- When mapping an endpoint window, verify that the address hasn't
been mapped already (Damien Le Moal)
- Implement pci_epc_ops.align_addr() for rockchip-ep (Damien Le Moal)
- Fix MSI IRQ data mapping to observe the alignment constraint, which
fixes intermittent page faults in memcpy_toio() and memcpy_fromio()
(Damien Le Moal)
- Rename rockchip_pcie_parse_ep_dt() to
rockchip_pcie_ep_get_resources() for consistency with similar DT
interfaces (Damien Le Moal)
- Skip the unnecessary link train in rockchip_pcie_ep_probe() and do
it only in the endpoint start operation (Damien Le Moal)
- Implement pci_epc_ops.stop_link() to disable link training and
controller configuration (Damien Le Moal)
- Attempt link training at 5 GT/s when both partners support it
(Damien Le Moal)
- Add a handler for PERST# signal so we can detect host-initiated
resets and start link training after PERST# is deasserted (Damien
Le Moal)
Synopsys DesignWare PCIe controller driver:
- Clear outbound address on unmap so dw_pcie_find_index() won't match
an ATU index that was already unmapped (Damien Le Moal)
- Use of_property_present() instead of of_property_read_bool() when
testing for presence of non-boolean DT properties (Rob Herring)
- Advertise 1MB size if endpoint supports Resizable BARs, which was
inadvertently lost in v6.11 (Niklas Cassel)
TI J721E PCIe driver:
- Add PCIe support for J722S SoC (Siddharth Vadapalli)
- Delay PCIE_T_PVPERL_MS (100 ms), not just PCIE_T_PERST_CLK_US (100
us), before deasserting PERST# to ensure power and refclk are
stable (Siddharth Vadapalli)
TI Keystone PCIe controller driver:
- Set the 'ti,keystone-pcie' mode so v3.65a devices work in Root
Complex mode (Kishon Vijay Abraham I)
- Try to avoid unrecoverable SError for attempts to issue config
transactions when the link is down; this is racy but the best we
can do (Kishon Vijay Abraham I)
Miscellaneous:
- Reorganize kerneldoc parameter names to match order in function
signature (Julia Lawall)
- Fix sysfs reset_method_store() memory leak (Todd Kjos)
- Simplify pci_create_slot() (Ilpo Järvinen)
- Fix incorrect printf format specifiers in pcitest (Luo Yifan)"
* tag 'pci-v6.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (127 commits)
PCI: rockchip-ep: Handle PERST# signal in EP mode
PCI: rockchip-ep: Improve link training
PCI: rockship-ep: Implement the pci_epc_ops::stop_link() operation
PCI: rockchip-ep: Refactor endpoint link training enable
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() MSI-X hiding
PCI: rockchip-ep: Refactor rockchip_pcie_ep_probe() memory allocations
PCI: rockchip-ep: Rename rockchip_pcie_parse_ep_dt()
PCI: rockchip-ep: Fix MSI IRQ data mapping
PCI: rockchip-ep: Implement the pci_epc_ops::align_addr() operation
PCI: rockchip-ep: Improve rockchip_pcie_ep_map_addr()
PCI: rockchip-ep: Improve rockchip_pcie_ep_unmap_addr()
PCI: rockchip-ep: Use a macro to define EP controller .align feature
PCI: rockchip-ep: Fix address translation unit programming
PCI/pwrctrl: Rename pwrctrl functions and structures
PCI/pwrctrl: Rename pwrctl files to pwrctrl
PCI/pwrctl: Remove pwrctl device without iterating over all children of pwrctl parent
PCI/pwrctl: Ensure that pwrctl drivers are probed before PCI client drivers
PCI/pwrctl: Create pwrctl device only if at least one power supply is present
PCI/pwrctl: Use of_platform_device_create() to create pwrctl devices
tools: PCI: Fix incorrect printf format specifiers
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux
Pull iommu updates from Joerg Roedel:
"Core Updates:
- Convert call-sites using iommu_domain_alloc() to more specific
versions and remove function
- Introduce iommu_paging_domain_alloc_flags()
- Extend support for allocating PASID-capable domains to more drivers
- Remove iommu_present()
- Some smaller improvements
New IOMMU driver for RISC-V
Intel VT-d Updates:
- Add domain_alloc_paging support
- Enable user space IOPFs in non-PASID and non-svm cases
- Small code refactoring and cleanups
- Add domain replacement support for pasid
AMD-Vi Updates:
- Adapt to iommu_paging_domain_alloc_flags() interface and alloc V2
page-tables by default
- Replace custom domain ID allocator with IDA allocator
- Add ops->release_domain() support
- Other improvements to device attach and domain allocation code
paths
ARM-SMMU Updates:
- SMMUv2:
- Return -EPROBE_DEFER for client devices probing before their
SMMU
- Devicetree binding updates for Qualcomm MMU-500 implementations
- SMMUv3:
- Minor fixes and cleanup for NVIDIA's virtual command queue
driver
- IO-PGTable:
- Fix indexing of concatenated PGDs and extend selftest coverage
- Remove unused block-splitting support
S390 IOMMU:
- Implement support for blocking domain
Mediatek IOMMU:
- Enable 35-bit physical address support for mt8186
OMAP IOMMU driver:
- Adapt to recent IOMMU core changes and unbreak driver"
* tag 'iommu-updates-v6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/iommu/linux: (92 commits)
iommu/tegra241-cmdqv: Fix alignment failure at max_n_shift
iommu: Make set_dev_pasid op support domain replacement
iommu/arm-smmu-v3: Make set_dev_pasid() op support replace
iommu/vt-d: Add set_dev_pasid callback for nested domain
iommu/vt-d: Make identity_domain_set_dev_pasid() to handle domain replacement
iommu/vt-d: Make intel_svm_set_dev_pasid() support domain replacement
iommu/vt-d: Limit intel_iommu_set_dev_pasid() for paging domain
iommu/vt-d: Make intel_iommu_set_dev_pasid() to handle domain replacement
iommu/vt-d: Add iommu_domain_did() to get did
iommu/vt-d: Consolidate the struct dev_pasid_info add/remove
iommu/vt-d: Add pasid replace helpers
iommu/vt-d: Refactor the pasid setup helpers
iommu/vt-d: Add a helper to flush cache for updating present pasid entry
iommu: Pass old domain to set_dev_pasid op
iommu/iova: Fix typo 'adderss'
iommu: Add a kdoc to iommu_unmap()
iommu/io-pgtable-arm-v7s: Remove split on unmap behavior
iommu/io-pgtable-arm: Remove split on unmap behavior
iommu/vt-d: Drain PRQs when domain removed from RID
iommu/vt-d: Drop pasid requirement for prq initialization
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Add firmware sysfs interface which allows user space to retrieve the
dump area size of the machine
- Add 'measurement_chars_full' CHPID sysfs attribute to make the
complete associated Channel-Measurements Characteristics Block
available
- Add virtio-mem support
- Move gmap aka KVM page fault handling from the main fault handler to
KVM code. This is the first step to make s390 KVM page fault handling
similar to other architectures. With this first step the main fault
handler does not have any special handling anymore, and therefore
convert it to support LOCK_MM_AND_FIND_VMA
- With gcc 14 s390 support for flag output operand support for inline
assemblies was added. This allows for several optimizations:
- Provide a cmpxchg inline assembly which makes use of this, and
provide all variants of arch_try_cmpxchg() so that the compiler
can generate slightly better code
- Convert a few cmpxchg() loops to try_cmpxchg() loops
- Similar to x86 add a CC_OUT() helper macro (and other macros),
and convert all inline assemblies to make use of them, so that
depending on compiler version better code can be generated
- List installed host-key hashes in sysfs if the machine supports the
Query Ultravisor Keys UVC
- Add 'Retrieve Secret' ioctl which allows user space in protected
execution guests to retrieve previously stored secrets from the
Ultravisor
- Add pkey-uv module which supports the conversion of Ultravisor
retrievable secrets to protected keys
- Extend the existing paes cipher to exploit the full AES-XTS hardware
acceleration introduced with message-security assist extension 10
- Convert hopefully all sysfs show functions to use sysfs_emit() so
that the constant flow of such patches stop
- For PCI devices make use of the newly added Topology ID attribute to
enable whole card multi-function support despite the change to PCHID
per port. Additionally improve the overall robustness and usability
of the multifunction support
- Various other small improvements, fixes, and cleanups
* tag 's390-6.13-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (133 commits)
s390/cio/ioasm: Convert to use flag output macros
s390/cio/qdio: Convert to use flag output macros
s390/sclp: Convert to use flag output macros
s390/dasd: Convert to use flag output macros
s390/boot/physmem: Convert to use flag output macros
s390/pci: Convert to use flag output macros
s390/kvm: Convert to use flag output macros
s390/extmem: Convert to use flag output macros
s390/string: Convert to use flag output macros
s390/diag: Convert to use flag output macros
s390/irq: Convert to use flag output macros
s390/smp: Convert to use flag output macros
s390/uv: Convert to use flag output macros
s390/pai: Convert to use flag output macros
s390/mm: Convert to use flag output macros
s390/cpu_mf: Convert to use flag output macros
s390/cpcmd: Convert to use flag output macros
s390/topology: Convert to use flag output macros
s390/time: Convert to use flag output macros
s390/pageattr: Convert to use flag output macros
...
|
|
into next
|
|
Use flag output macros in inline asm to allow for better code generation if
the compiler has support for the flag output constraint.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Tested-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Juergen Christ <jchrist@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
While pci_iov.h has include guards it doesn't include the necessary
header for struct zpci_dev, pci_bus.h on the other hand lacks even basic
include guards. This isn't only fragile and breaks convention but also
confuses tooling such as clang-analyzer. Add both include guards and the
necessary includes.
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
2fe2abf896c1 ("PCI: augment bus resource table with a list") added
PCI_SUBTRACTIVE_DECODE which is put into the struct pci_bus_resource flags
field but is never read. There seems to never have been users for it.
Remove both PCI_SUBTRACTIVE_DECODE and the flags field from the struct
pci_bus_resource.
Link: https://lore.kernel.org/r/20241017141111.44612-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This fixes a crash when surprise hot-unplugging a PCI device. This crash
happens because during hot-unplug __iommu_group_set_domain_nofail()
attaching the default domain fails when the platform no longer
recognizes the device as it has already been removed and we end up with
a NULL domain pointer and UAF. This is exactly the case referred to in
the second comment in __iommu_device_set_domain() and just as stated
there if we can instead attach the blocking domain the UAF is prevented
as this can handle the already removed device. Implement the blocking
domain to use this handling. With this change, the crash is fixed but
we still hit a warning attempting to change DMA ownership on a blocked
device.
Fixes: c76c067e488c ("s390/pci: Use dma-iommu layer")
Co-developed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Matthew Rosato <mjrosato@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/20240910211516.137933-1-mjrosato@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
This attribute will be used to communicate function type specific
firmware controlled flag bits.
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Alexandra Winter <wintera@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Per Documentation/filesystems/sysfs.rst, sysfs_emit() is preferred over
sprintf for presenting attributes to user space. Convert over two
left-over uses in the s390 PCI code.
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Ensure that VFs used in isolation, that is with their parent PF not
visible to the configuration but with their RID exposed, are treated
compatibly with existing isolated VF use cases without exposed RID
including RoCE Express VFs. This allows creating configurations where
one LPAR manages PFs while their child VFs are used by other LPARs. This
gives the LPAR managing the PFs a role analogous to that of the
hypervisor in a typical use case of passing child VFs to guests.
Instead of creating a multifunction struct zpci_bus whenever a PCI
function with RID exposed is discovered only create such a bus for
configured physical functions and only consider multifunction busses
when searching for an existing bus. Additionally only set zdev->devfn to
the devfn part of the RID once the function is added to a multifunction
bus.
This also fixes probing of more than 7 such isolated VFs from the same
physical bus. This is because common PCI code in pci_scan_slot() only
looks for more functions when pdev->multifunction is set which somewhat
counter intutively is not the case for VFs.
Note that PFs are looked at before their child VFs is guaranteed because
we sort the zpci_list by RID ascending.
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The newly introduced topology ID (TID) field in the CLP Query PCI
Function explicitly identifies groups of PCI functions whose RIDs belong
to the same (sub-)topology. When available use the TID instead of the
PCHID to match zPCI busses/domains for multi-function devices. Note that
currently only a single PCI bus per TID is supported. This change is
required because in future machines the PCHID will not identify a PCI
card but a specific port in the case of some multi-port NICs while from
a PCI point of view the entire card is a subtopology.
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Instead of relying on the observed but not architected firmware behavior
that PCI functions from the same card are listed in ascending RID order
in clp_list_pci() ensure this by sorting. To allow for sorting separate
the initial clp_list_pci() and creation of the virtual PCI busses.
Note that fundamentally in our per-PCI function hotplug design non RID
order of discovery is still possible. For example when the two PFs of
a two port NIC are hotplugged after initial boot and in descending RID
order. In this case the virtual PCI bus would be created by the second
PF using that PF's UID as domain number instead of that of the first PF.
Thus the domain number would then change from the UID of the second PF
to that of the first PF on reboot but there is really nothing we can do
about that since changing domain numbers at runtime seems even worse.
This only impacts the domain number as the RIDs are consistent and thus
even with just the second PF visible it will show up in the correct
position on the virtual bus.
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The Linux implementation of PCI error recovery for s390 was based on the
understanding that firmware error recovery is a two step process with an
optional initial error event to indicate the cause of the error if known
followed by either error event 0x3A (Success) or 0x3B (Failure) to
indicate whether firmware was able to recover. While this has been the
case in testing and the error cases seen in the wild it turns out this
is not correct. Instead firmware only generates 0x3A for some error and
service scenarios and expects the OS to perform recovery for all PCI
events codes except for those indicating permanent error (0x3B, 0x40)
and those indicating errors on the function measurement block (0x2A,
0x2B, 0x2C). Align Linux behavior with these expectations.
Fixes: 4cdf2f4e24ff ("s390/pci: implement minimal PCI error recovery")
Reviewed-by: Gerd Bayer <gbayer@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
no_llseek had been defined to NULL two years ago, in commit 868941b14441
("fs: remove no_llseek")
To quote that commit,
At -rc1 we'll need do a mechanical removal of no_llseek -
git grep -l -w no_llseek | grep -v porting.rst | while read i; do
sed -i '/\<no_llseek\>/d' $i
done
would do it.
Unfortunately, that hadn't been done. Linus, could you do that now, so
that we could finally put that thing to rest? All instances are of the
form
.llseek = no_llseek,
so it's obviously safe.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Wait for device readiness after reset by polling Vendor ID and
looking for Configuration RRS instead of polling the Command
register and looking for non-error completions, to avoid hardware
retries done for RRS on non-Vendor ID reads (Bjorn Helgaas)
- Rename CRS Completion Status to RRS ('Request Retry Status') to
match PCIe r6.0 spec usage (Bjorn Helgaas)
- Clear LBMS bit after a manual link retrain so we don't try to
retrain a link when there's no downstream device anymore (Maciej W.
Rozycki)
- Revert to the original link speed after retraining fails instead of
leaving it restricted to 2.5GT/s, so a future device has a chance
to use higher speeds (Maciej W. Rozycki)
- Wait for each level of downstream bus, not just the first, to
become accessible before restoring devices on that bus (Ilpo
Järvinen)
- Add ARCH_PCI_DEV_GROUPS so s390 can add its own attribute_groups
without having to stomp on the core's pdev->dev.groups (Lukas
Wunner)
Driver binding:
- Export pcim_request_region(), a managed counterpart of
pci_request_region(), for use by drivers (Philipp Stanner)
- Export pcim_iomap_region() and deprecate pcim_iomap_regions()
(Philipp Stanner)
- Request the PCI BAR used by xboxvideo (Philipp Stanner)
- Request and map drm/ast BARs with pcim_iomap_region() (Philipp
Stanner)
MSI:
- Add MSI_FLAG_NO_AFFINITY flag for devices that mux MSIs onto a
single IRQ line and cannot set the affinity of each MSI to a
specific CPU core (Marek Vasut)
- Use MSI_FLAG_NO_AFFINITY and remove unnecessary .irq_set_affinity()
implementations in aardvark, altera, brcmstb, dwc, mediatek-gen3,
mediatek, mobiveil, plda, rcar, tegra, vmd, xilinx-nwl,
xilinx-xdma, and xilinx drivers to avoid 'IRQ: set affinity failed'
warnings (Marek Vasut)
Power management:
- Add pwrctl support for ATH11K inside the WCN6855 package (Konrad
Dybcio)
PCI device hotplug:
- Remove unnecessary hpc_ops struct from shpchp (ngn)
- Check for PCI_POSSIBLE_ERROR(), not 0xffffffff, in cpqphp
(weiyufeng)
Virtualization:
- Mark Creative Labs EMU20k2 INTx masking as broken (Alex Williamson)
- Add an ACS quirk for Qualcomm SA8775P, which doesn't advertise ACS
but does provide ACS-like features (Subramanian Ananthanarayanan)
IOMMU:
- Add function 0 DMA alias quirk for Glenfly Arise audio function,
which uses the function 0 Requester ID (WangYuli)
NPEM:
- Add Native PCIe Enclosure Management (NPEM) support for sysfs
control of NVMe RAID storage indicators (ok/fail/locate/
rebuild/etc) (Mariusz Tkaczyk)
- Add support for the ACPI _DSM PCIe SSD status LED management, which
is functionally similar to NPEM but mediated by platform firmware
(Mariusz Tkaczyk)
Device trees:
- Drop minItems and maxItems from ranges in PCI generic host binding
since host bridges may have several MMIO and I/O port apertures
(Frank Li)
- Add kirin, rcar-gen2, uniphier DT binding top-level constraints for
clocks (Krzysztof Kozlowski)
Altera PCIe controller driver:
- Convert altera DT bindings from text to YAML (Matthew Gerlach)
- Replace TLP_REQ_ID() with macro PCI_DEVID(), which does the same
thing and is what other drivers use (Jinjie Ruan)
Broadcom STB PCIe controller driver:
- Add DT binding maxItems for reset controllers (Jim Quinlan)
- Use the 'bridge' reset method if described in the DT (Jim Quinlan)
- Use the 'swinit' reset method if described in the DT (Jim Quinlan)
- Add 'has_phy' so the existence of a 'rescal' reset controller
doesn't imply software control of it (Jim Quinlan)
- Add support for many inbound DMA windows (Jim Quinlan)
- Rename SoC 'type' to 'soc_base' express the fact that SoCs come in
families of multiple similar devices (Jim Quinlan)
- Add Broadcom 7712 DT description and driver support (Jim Quinlan)
- Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings for
maintainability (Bjorn Helgaas)
Freescale i.MX6 PCIe controller driver:
- Add imx6q-pcie 'dbi2' and 'atu' reg-names for i.MX8M Endpoints
(Richard Zhu)
- Fix a code restructuring error that caused i.MX8MM and i.MX8MP
Endpoints to fail to establish link (Richard Zhu)
- Fix i.MX8MP Endpoint occasional failure to trigger MSI by enforcing
outbound alignment requirement (Richard Zhu)
- Call phy_power_off() in the .probe() error path (Frank Li)
- Rename internal names from imx6_* to imx_* since i.MX7/8/9 are also
supported (Frank Li)
- Manage Refclk by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Manage core reset by using SoC-specific callbacks instead of switch
statements (Frank Li)
- Expand comments for erratum ERR010728 workaround (Frank Li)
- Use generic PHY APIs to configure mode, speed, and submode, which
is harmless for devices that implement their own internal PHY
management and don't set the generic imx_pcie->phy (Frank Li)
- Add i.MX8Q (i.MX8QM, i.MX8QXP, and i.MX8DXL) DT binding and driver
Root Complex support (Richard Zhu)
Freescale Layerscape PCIe controller driver:
- Replace layerscape-pcie DT binding compatible fsl,lx2160a-pcie with
fsl,lx2160ar2-pcie (Frank Li)
- Add layerscape-pcie DT binding deprecated 'num-viewport' property
to address a DT checker warning (Frank Li)
- Change layerscape-pcie DT binding 'fsl,pcie-scfg' to phandle-array
(Frank Li)
Loongson PCIe controller driver:
- Increase max PCI hosts to 8 for Loongson-3C6000 and newer chipsets
(Huacai Chen)
Marvell Aardvark PCIe controller driver:
- Fix issue with emulating Configuration RRS for two-byte reads of
Vendor ID; previously it only worked for four-byte reads (Bjorn
Helgaas)
MediaTek PCIe Gen3 controller driver:
- Add per-SoC struct mtk_gen3_pcie_pdata to support multiple SoC
types (Lorenzo Bianconi)
- Use reset_bulk APIs to manage PHY reset lines (Lorenzo Bianconi)
- Add DT and driver support for Airoha EN7581 PCIe controller
(Lorenzo Bianconi)
Qualcomm PCIe controller driver:
- Update qcom,pcie-sc7280 DT binding with eight interrupts (Rayyan
Ansari)
- Add back DT 'vddpe-3v3-supply', which was incorrectly removed
earlier (Johan Hovold)
- Drop endpoint redundant masking of global IRQ events (Manivannan
Sadhasivam)
- Clarify unknown global IRQ message and only log it once to avoid a
flood (Manivannan Sadhasivam)
- Add 'linux,pci-domain' property to endpoint DT binding (Manivannan
Sadhasivam)
- Assign PCI domain number for endpoint controllers (Manivannan
Sadhasivam)
- Add 'qcom_pcie_ep' and the PCI domain number to IRQ names for
endpoint controller (Manivannan Sadhasivam)
- Add global SPI interrupt for PCIe link events to DT binding
(Manivannan Sadhasivam)
- Add global RC interrupt handler to handle 'Link up' events and
automatically enumerate hot-added devices (Manivannan Sadhasivam)
- Avoid mirroring of DBI and iATU register space so it doesn't
overlap BAR MMIO space (Prudhvi Yarlagadda)
- Enable controller resources like PHY only after PERST# is
deasserted to partially avoid the problem that the endpoint SoC
crashes when accessing things when Refclk is absent (Manivannan
Sadhasivam)
- Add 16.0 GT/s equalization and RX lane margining settings (Shashank
Babu Chinta Venkata)
- Pass domain number to pci_bus_release_domain_nr() explicitly to
avoid a NULL pointer dereference (Manivannan Sadhasivam)
Renesas R-Car PCIe controller driver:
- Make the read-only const array 'check_addr' static (Colin Ian King)
- Add R-Car V4M (R8A779H0) PCIe host and endpoint to DT binding
(Yoshihiro Shimoda)
TI DRA7xx PCIe controller driver:
- Request IRQF_ONESHOT for 'dra7xx-pcie-main' IRQ since the primary
handler is NULL (Siddharth Vadapalli)
- Handle IRQ request errors during root port and endpoint probe
(Siddharth Vadapalli)
TI J721E PCIe driver:
- Add DT 'ti,syscon-acspcie-proxy-ctrl' and driver support to enable
the ACSPCIE module to drive Refclk for the Endpoint (Siddharth
Vadapalli)
- Extract the cadence link setup from cdns_pcie_host_setup() so link
setup can be done separately during resume (Thomas Richard)
- Add T_PERST_CLK_US definition for the mandatory delay between
Refclk becoming stable and PERST# being deasserted (Thomas Richard)
- Add j721e suspend and resume support (Théo Lebrun)
TI Keystone PCIe controller driver:
- Fix NULL pointer checking when applying MRRS limitation quirk for
AM65x SR 1.0 Errata #i2037 (Dan Carpenter)
Xilinx NWL PCIe controller driver:
- Fix off-by-one error in INTx IRQ handler that caused INTx
interrupts to be lost or delivered as the wrong interrupt (Sean
Anderson)
- Rate-limit misc interrupt messages (Sean Anderson)
- Turn off the clock on probe failure and device removal (Sean
Anderson)
- Add DT binding and driver support for enabling/disabling PHYs (Sean
Anderson)
- Add PCIe phy bindings for the ZCU102 (Sean Anderson)
Xilinx XDMA PCIe controller driver:
- Add support for Xilinx QDMA Soft IP PCIe Root Port Bridge to DT
binding and xilinx-dma-pl driver (Thippeswamy Havalige)
Miscellaneous:
- Fix buffer overflow in kirin_pcie_parse_port() (Alexandra Diupina)
- Fix minor kerneldoc issues and typos (Bjorn Helgaas)
- Use PCI_DEVID() macro in aer_inject() instead of open-coding it
(Jinjie Ruan)
- Check pcie_find_root_port() return in x86 fixups to avoid NULL
pointer dereferences (Samasth Norway Ananda)
- Make pci_bus_type constant (Kunwu Chan)
- Remove unused declarations of __pci_pme_wakeup() and
pci_vpd_release() (Yue Haibing)
- Remove any leftover .*.cmd files with make clean (zhang jiao)
- Remove unused BILLION macro (zhang jiao)"
* tag 'pci-v6.12-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/pci/pci: (132 commits)
PCI: Fix typos
dt-bindings: PCI: qcom: Allow 'vddpe-3v3-supply' again
tools: PCI: Remove unused BILLION macro
tools: PCI: Remove .*.cmd files with make clean
PCI: Pass domain number to pci_bus_release_domain_nr() explicitly
PCI: dra7xx: Fix error handling when IRQ request fails in probe
PCI: dra7xx: Fix threaded IRQ request for "dra7xx-pcie-main" IRQ
PCI: qcom: Add RX lane margining settings for 16.0 GT/s
PCI: qcom: Add equalization settings for 16.0 GT/s
PCI: dwc: Always cache the maximum link speed value in dw_pcie::max_link_speed
PCI: dwc: Rename 'dw_pcie::link_gen' to 'dw_pcie::max_link_speed'
PCI: qcom-ep: Enable controller resources like PHY only after refclk is available
PCI: Mark Creative Labs EMU20k2 INTx masking as broken
dt-bindings: PCI: imx6q-pcie: Add reg-name "dbi2" and "atu" for i.MX8M PCIe Endpoint
dt-bindings: PCI: altera: msi: Convert to YAML
PCI: imx6: Add i.MX8Q PCIe Root Complex (RC) support
PCI: Rename CRS Completion Status to RRS
PCI: aardvark: Correct Configuration RRS checking
PCI: Wait for device readiness with Configuration RRS
PCI: brcmstb: Sort enums, pcie_offsets[], pcie_cfg_data, .compatible strings
...
|
|
Use the new API that can understand huge pfn mappings.
Link: https://lkml.kernel.org/r/20240826204353.2228736-12-peterx@redhat.com
Signed-off-by: Peter Xu <peterx@redhat.com>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Vasily Gorbik <gor@linux.ibm.com>
Cc: Alexander Gordeev <agordeev@linux.ibm.com>
Cc: Christian Borntraeger <borntraeger@linux.ibm.com>
Cc: Sven Schnelle <svens@linux.ibm.com>
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Aneesh Kumar K.V <aneesh.kumar@linux.ibm.com>
Cc: Borislav Petkov <bp@alien8.de>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dave Hansen <dave.hansen@linux.intel.com>
Cc: David Hildenbrand <david@redhat.com>
Cc: Gavin Shan <gshan@redhat.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Jason Gunthorpe <jgg@nvidia.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Ryan Roberts <ryan.roberts@arm.com>
Cc: Sean Christopherson <seanjc@google.com>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: Will Deacon <will@kernel.org>
Cc: Zi Yan <ziy@nvidia.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
Bjorn suggests using pdev->dev.groups for attribute_groups constructed on
PCI device enumeration:
"Is it feasible to build an attribute group in pci_doe_init() and
add it to dev->groups so device_add() will automatically add them?"
https://lore.kernel.org/r/20231019165829.GA1381099@bhelgaas
Unfortunately on s390, pcibios_device_add() usurps pdev->dev.groups for
arch-specific attribute_groups, preventing its use for anything else.
Introduce an ARCH_PCI_DEV_GROUPS macro which arches can define in
<asm/pci.h>. The macro is visible in drivers/pci/pci-sysfs.c through the
inclusion of <linux/pci.h>, which in turn includes <asm/pci.h>.
On s390, define the macro to the three attribute_groups previously assigned
to pdev->dev.groups. Thereby pdev->dev.groups is made available for use by
the PCI core.
As a side effect, arch/s390/pci/pci_sysfs.c no longer needs to be compiled
into the kernel if CONFIG_SYSFS=n.
Link: https://lore.kernel.org/r/7b970f7923e373d1b23784721208f93418720485.1722870934.git.lukas@wunner.de
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
|
|
On a PCI adapter that provides up to 8 MSI interrupt sources the s390
implementation of PCI interrupts rejected to accommodate them, although
the underlying hardware is able to support that.
For MSI-X it is sufficient to allocate a single irq_desc per msi_desc,
but for MSI multiple irq descriptors are attached to and controlled by
a single msi descriptor. Add the appropriate loops to maintain multiple
irq descriptors and tie/untie them to/from the appropriate AIBV bit, if
a device driver allocates more than 1 MSI interrupt.
Common PCI code passes on requests to allocate a number of interrupt
vectors based on the device drivers' demand and the PCI functions'
capabilities. However, the root-complex of s390 systems support just a
limited number of interrupt vectors per PCI function.
Produce a kernel log message to inform about any architecture-specific
capping that might be done.
With this change, we had a PCI adapter successfully raising
interrupts to its device driver via all 8 sources.
Fixes: a384c8924a8b ("s390/PCI: Fix single MSI only check")
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Factor out adapter interrupt allocation from arch_setup_msi_irqs() in
preparation for enabling registration of multiple MSIs. Code movement
only, no change of functionality intended.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Remove restrictions on PAI NNPA and crypto counters, enabling
concurrent per-task and system-wide sampling and counting events
- Switch to GENERIC_CPU_DEVICES by setting up the CPU present mask in
the architecture code and letting the generic code handle CPU
bring-up
- Add support for the diag204 busy indication facility to prevent
undesirable blocking during hypervisor logical CPU utilization
queries. Implement results caching
- Improve the handling of Store Data SCLP events by suppressing
unnecessary warning, preventing buffer release in I/O during
failures, and adding timeout handling for Store Data requests to
address potential firmware issues
- Provide optimized __arch_hweight*() implementations
- Remove the unnecessary CPU KOBJ_CHANGE uevents generated during
topology updates, as they are unused and also not present on other
architectures
- Cleanup atomic_ops, optimize __atomic_set() for small values and
__atomic_cmpxchg_bool() for compilers supporting flag output
constraint
- Couple of cleanups for KVM:
- Move and improve KVM struct definitions for DAT tables from
gaccess.c to a new header
- Pass the asce as parameter to sie64a()
- Make the crdte() and cspg() page table handling wrappers return a
boolean to indicate success, like the other existing "compare and
swap" wrappers
- Add documentation for HWCAP flags
- Switch to obtaining total RAM pages from memblock instead of
totalram_pages() during mm init, to ensure correct calculation of
zero page size, when defer_init is enabled
- Refactor lowcore access and switch to using the get_lowcore()
function instead of the S390_lowcore macro
- Cleanups for PG_arch_1 and folio handling in UV and hugetlb code
- Add missing MODULE_DESCRIPTION() macros
- Fix VM_FAULT_HWPOISON handling in do_exception()
* tag 's390-6.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (54 commits)
s390/mm: Fix VM_FAULT_HWPOISON handling in do_exception()
s390/kvm: Move bitfields for dat tables
s390/entry: Pass the asce as parameter to sie64a()
s390/sthyi: Use cached data when diag is busy
s390/sthyi: Move diag operations
s390/hypfs_diag: Diag204 busy loop
s390/diag: Add busy-indication-facility requirements
s390/diag: Diag204 add busy return errno
s390/diag: Return errno's from diag204
s390/sclp: Diag204 busy indication facility detection
s390/atomic_ops: Make use of flag output constraint
s390/atomic_ops: Improve __atomic_set() for small values
s390/atomic_ops: Use symbolic names
s390/smp: Switch to GENERIC_CPU_DEVICES
s390/hwcaps: Add documentation for HWCAP flags
s390/pgtable: Make crdte() and cspg() return a value
s390/topology: Remove CPU KOBJ_CHANGE uevents
s390/sclp: Add timeout to Store Data requests
s390/sclp: Prevent release of buffer in I/O
s390/sclp: Suppress unnecessary Store Data warning
...
|
|
Replace all S390_lowcore usages in arch/s390/ by get_lowcore().
Acked-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Sven Schnelle <svens@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
In commit 4e4dc65ab578 ("s390/pci: use phys_to_virt() for AIBVs/DIBVs")
the setting of dibv_addr was missed when adding virt_to_phys(). This
only affects systems with directed interrupt delivery enabled which are
not generally available.
Fixes: 4e4dc65ab578 ("s390/pci: use phys_to_virt() for AIBVs/DIBVs")
Reviewed-by: Heiko Carstens <hca@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm
Pull mm updates from Andrew Morton:
"The usual shower of singleton fixes and minor series all over MM,
documented (hopefully adequately) in the respective changelogs.
Notable series include:
- Lucas Stach has provided some page-mapping cleanup/consolidation/
maintainability work in the series "mm/treewide: Remove pXd_huge()
API".
- In the series "Allow migrate on protnone reference with
MPOL_PREFERRED_MANY policy", Donet Tom has optimized mempolicy's
MPOL_PREFERRED_MANY mode, yielding almost doubled performance in
one test.
- In their series "Memory allocation profiling" Kent Overstreet and
Suren Baghdasaryan have contributed a means of determining (via
/proc/allocinfo) whereabouts in the kernel memory is being
allocated: number of calls and amount of memory.
- Matthew Wilcox has provided the series "Various significant MM
patches" which does a number of rather unrelated things, but in
largely similar code sites.
- In his series "mm: page_alloc: freelist migratetype hygiene"
Johannes Weiner has fixed the page allocator's handling of
migratetype requests, with resulting improvements in compaction
efficiency.
- In the series "make the hugetlb migration strategy consistent"
Baolin Wang has fixed a hugetlb migration issue, which should
improve hugetlb allocation reliability.
- Liu Shixin has hit an I/O meltdown caused by readahead in a
memory-tight memcg. Addressed in the series "Fix I/O high when
memory almost met memcg limit".
- In the series "mm/filemap: optimize folio adding and splitting"
Kairui Song has optimized pagecache insertion, yielding ~10%
performance improvement in one test.
- Baoquan He has cleaned up and consolidated the early zone
initialization code in the series "mm/mm_init.c: refactor
free_area_init_core()".
- Baoquan has also redone some MM initializatio code in the series
"mm/init: minor clean up and improvement".
- MM helper cleanups from Christoph Hellwig in his series "remove
follow_pfn".
- More cleanups from Matthew Wilcox in the series "Various
page->flags cleanups".
- Vlastimil Babka has contributed maintainability improvements in the
series "memcg_kmem hooks refactoring".
- More folio conversions and cleanups in Matthew Wilcox's series:
"Convert huge_zero_page to huge_zero_folio"
"khugepaged folio conversions"
"Remove page_idle and page_young wrappers"
"Use folio APIs in procfs"
"Clean up __folio_put()"
"Some cleanups for memory-failure"
"Remove page_mapping()"
"More folio compat code removal"
- David Hildenbrand chipped in with "fs/proc/task_mmu: convert
hugetlb functions to work on folis".
- Code consolidation and cleanup work related to GUP's handling of
hugetlbs in Peter Xu's series "mm/gup: Unify hugetlb, part 2".
- Rick Edgecombe has developed some fixes to stack guard gaps in the
series "Cover a guard gap corner case".
- Jinjiang Tu has fixed KSM's behaviour after a fork+exec in the
series "mm/ksm: fix ksm exec support for prctl".
- Baolin Wang has implemented NUMA balancing for multi-size THPs.
This is a simple first-cut implementation for now. The series is
"support multi-size THP numa balancing".
- Cleanups to vma handling helper functions from Matthew Wilcox in
the series "Unify vma_address and vma_pgoff_address".
- Some selftests maintenance work from Dev Jain in the series
"selftests/mm: mremap_test: Optimizations and style fixes".
- Improvements to the swapping of multi-size THPs from Ryan Roberts
in the series "Swap-out mTHP without splitting".
- Kefeng Wang has significantly optimized the handling of arm64's
permission page faults in the series
"arch/mm/fault: accelerate pagefault when badaccess"
"mm: remove arch's private VM_FAULT_BADMAP/BADACCESS"
- GUP cleanups from David Hildenbrand in "mm/gup: consistently call
it GUP-fast".
- hugetlb fault code cleanups from Vishal Moola in "Hugetlb fault
path to use struct vm_fault".
- selftests build fixes from John Hubbard in the series "Fix
selftests/mm build without requiring "make headers"".
- Memory tiering fixes/improvements from Ho-Ren (Jack) Chuang in the
series "Improved Memory Tier Creation for CPUless NUMA Nodes".
Fixes the initialization code so that migration between different
memory types works as intended.
- David Hildenbrand has improved follow_pte() and fixed an errant
driver in the series "mm: follow_pte() improvements and acrn
follow_pte() fixes".
- David also did some cleanup work on large folio mapcounts in his
series "mm: mapcount for large folios + page_mapcount() cleanups".
- Folio conversions in KSM in Alex Shi's series "transfer page to
folio in KSM".
- Barry Song has added some sysfs stats for monitoring multi-size
THP's in the series "mm: add per-order mTHP alloc and swpout
counters".
- Some zswap cleanups from Yosry Ahmed in the series "zswap
same-filled and limit checking cleanups".
- Matthew Wilcox has been looking at buffer_head code and found the
documentation to be lacking. The series is "Improve buffer head
documentation".
- Multi-size THPs get more work, this time from Lance Yang. His
series "mm/madvise: enhance lazyfreeing with mTHP in madvise_free"
optimizes the freeing of these things.
- Kemeng Shi has added more userspace-visible writeback
instrumentation in the series "Improve visibility of writeback".
- Kemeng Shi then sent some maintenance work on top in the series
"Fix and cleanups to page-writeback".
- Matthew Wilcox reduces mmap_lock traffic in the anon vma code in
the series "Improve anon_vma scalability for anon VMAs". Intel's
test bot reported an improbable 3x improvement in one test.
- SeongJae Park adds some DAMON feature work in the series
"mm/damon: add a DAMOS filter type for page granularity access recheck"
"selftests/damon: add DAMOS quota goal test"
- Also some maintenance work in the series
"mm/damon/paddr: simplify page level access re-check for pageout"
"mm/damon: misc fixes and improvements"
- David Hildenbrand has disabled some known-to-fail selftests ni the
series "selftests: mm: cow: flag vmsplice() hugetlb tests as
XFAIL".
- memcg metadata storage optimizations from Shakeel Butt in "memcg:
reduce memory consumption by memcg stats".
- DAX fixes and maintenance work from Vishal Verma in the series
"dax/bus.c: Fixups for dax-bus locking""
* tag 'mm-stable-2024-05-17-19-19' of git://git.kernel.org/pub/scm/linux/kernel/git/akpm/mm: (426 commits)
memcg, oom: cleanup unused memcg_oom_gfp_mask and memcg_oom_order
selftests/mm: hugetlb_madv_vs_map: avoid test skipping by querying hugepage size at runtime
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_wp
mm/hugetlb: add missing VM_FAULT_SET_HINDEX in hugetlb_fault
selftests: cgroup: add tests to verify the zswap writeback path
mm: memcg: make alloc_mem_cgroup_per_node_info() return bool
mm/damon/core: fix return value from damos_wmark_metric_value
mm: do not update memcg stats for NR_{FILE/SHMEM}_PMDMAPPED
selftests: cgroup: remove redundant enabling of memory controller
Docs/mm/damon/maintainer-profile: allow posting patches based on damon/next tree
Docs/mm/damon/maintainer-profile: change the maintainer's timezone from PST to PT
Docs/mm/damon/design: use a list for supported filters
Docs/admin-guide/mm/damon/usage: fix wrong schemes effective quota update command
Docs/admin-guide/mm/damon/usage: fix wrong example of DAMOS filter matching sysfs file
selftests/damon: classify tests for functionalities and regressions
selftests/damon/_damon_sysfs: use 'is' instead of '==' for 'None'
selftests/damon/_damon_sysfs: find sysfs mount point from /proc/mounts
selftests/damon/_damon_sysfs: check errors from nr_schemes file reads
mm/damon/core: initialize ->esz_bp from damos_quota_init_priv()
selftests/damon: add a test for DAMOS quota goal
...
|
|
Pull rdma updates from Jason Gunthorpe:
"Aside from the usual things this has an arch update for
__iowrite64_copy() used by the RDMA drivers.
This API was intended to generate large 64 byte MemWr TLPs on PCI.
These days most processors had done this by just repeating writel() in
a loop. S390 and some new ARM64 designs require a special helper to
get this to generate.
- Small improvements and fixes for erdma, efa, hfi1, bnxt_re
- Fix a UAF crash after module unload on leaking restrack entry
- Continue adding full RDMA support in mana with support for EQs,
GID's and CQs
- Improvements to the mkey cache in mlx5
- DSCP traffic class support in hns and several bug fixes
- Cap the maximum number of MADs in the receive queue to avoid OOM
- Another batch of rxe bug fixes from large scale testing
- __iowrite64_copy() optimizations for write combining MMIO memory
- Remove NULL checks before dev_put/hold()
- EFA support for receive with immediate
- Fix a recent memleaking regression in a cma error path"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (70 commits)
RDMA/cma: Fix kmemleak in rdma_core observed during blktests nvme/rdma use siw
RDMA/IPoIB: Fix format truncation compilation errors
bnxt_re: avoid shift undefined behavior in bnxt_qplib_alloc_init_hwq
RDMA/efa: Support QP with unsolicited write w/ imm. receive
IB/hfi1: Remove generic .ndo_get_stats64
IB/hfi1: Do not use custom stat allocator
RDMA/hfi1: Use RMW accessors for changing LNKCTL2
RDMA/mana_ib: implement uapi for creation of rnic cq
RDMA/mana_ib: boundary check before installing cq callbacks
RDMA/mana_ib: introduce a helper to remove cq callbacks
RDMA/mana_ib: create and destroy RNIC cqs
RDMA/mana_ib: create EQs for RNIC CQs
RDMA/core: Remove NULL check before dev_{put, hold}
RDMA/ipoib: Remove NULL check before dev_{put, hold}
RDMA/mlx5: Remove NULL check before dev_{put, hold}
RDMA/mlx5: Track DCT, DCI and REG_UMR QPs as diver_detail resources.
RDMA/core: Add an option to display driver-specific QPs in the rdmatool
RDMA/efa: Add shutdown notifier
RDMA/mana_ib: Fix missing ret value
IB/mlx5: Use __iowrite64_copy() for write combining stores
...
|
|
... and centralize the VM_IO/VM_PFNMAP sanity check in there. We'll
now also perform these sanity checks for direct follow_pte()
invocations.
For generic_access_phys(), we might now check multiple times: nothing to
worry about, really.
Link: https://lkml.kernel.org/r/20240410155527.474777-3-david@redhat.com
Signed-off-by: David Hildenbrand <david@redhat.com>
Acked-by: Sean Christopherson <seanjc@google.com> [KVM]
Cc: Alex Williamson <alex.williamson@redhat.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Fei Li <fei1.li@intel.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Cc: Heiko Carstens <hca@linux.ibm.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Paolo Bonzini <pbonzini@redhat.com>
Cc: Yonghua Huang <yonghua.huang@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
|
|
The S/390 architecture doesn't support SMBIOS, so CONFIG_DMI will
never be defined there. So we can simply omit these preprocessing
directives and speed up the build a bit.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Cc: Niklas Schnelle <schnelle@linux.ibm.com>
Cc: Gerald Schaefer <gerald.schaefer@linux.ibm.com>
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20240423162724.3966265a@endymion.delvare
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
Complete switching the __iowriteXX_copy() routines over to use #define and
arch provided inline/macro functions instead of weak symbols.
S390 has an implementation that simply calls another memcpy
function. Inline this so the callers don't have to do two jumps.
Link: https://lore.kernel.org/r/3-v3-1893cd8b9369+1925-mlx5_arm_wc_jgg@nvidia.com
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Heiko Carstens:
- Various virtual vs physical address usage fixes
- Fix error handling in Processor Activity Instrumentation device
driver, and export number of counters with a sysfs file
- Allow for multiple events when Processor Activity Instrumentation
counters are monitored in system wide sampling
- Change multiplier and shift values of the Time-of-Day clock source to
improve steering precision
- Remove a couple of unneeded GFP_DMA flags from allocations
- Disable mmap alignment if randomize_va_space is also disabled, to
avoid a too small heap
- Various changes to allow s390 to be compiled with LLVM=1, since
ld.lld and llvm-objcopy will have proper s390 support witch clang 19
- Add __uninitialized macro to Compiler Attributes. This is helpful
with s390's FPU code where some users have up to 520 byte stack
frames. Clearing such stack frames (if INIT_STACK_ALL_PATTERN or
INIT_STACK_ALL_ZERO is enabled) before they are used contradicts the
intention (performance improvement) of such code sections.
- Convert switch_to() to an out-of-line function, and use the generic
switch_to header file
- Replace the usage of s390's debug feature with pr_debug() calls
within the zcrypt device driver
- Improve hotplug support of the Adjunct Processor device driver
- Improve retry handling in the zcrypt device driver
- Various changes to the in-kernel FPU code:
- Make in-kernel FPU sections preemptible
- Convert various larger inline assemblies and assembler files to
C, mainly by using singe instruction inline assemblies. This
increases readability, but also allows makes it easier to add
proper instrumentation hooks
- Cleanup of the header files
- Provide fast variants of csum_partial() and
csum_partial_copy_nocheck() based on vector instructions
- Introduce and use a lock to synchronize accesses to zpci device data
structures to avoid inconsistent states caused by concurrent accesses
- Compile the kernel without -fPIE. This addresses the following
problems if the kernel is compiled with -fPIE:
- It uses dynamic symbols (.dynsym), for which the linker refuses
to allow more than 64k sections. This can break features which
use '-ffunction-sections' and '-fdata-sections', including
kpatch-build and function granular KASLR
- It unnecessarily uses GOT relocations, adding an extra layer of
indirection for many memory accesses
- Fix shared_cpu_list for CPU private L2 caches, which incorrectly were
reported as globally shared
* tag 's390-6.9-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (117 commits)
s390/tools: handle rela R_390_GOTPCDBL/R_390_GOTOFF64
s390/cache: prevent rebuild of shared_cpu_list
s390/crypto: remove retry loop with sleep from PAES pkey invocation
s390/pkey: improve pkey retry behavior
s390/zcrypt: improve zcrypt retry behavior
s390/zcrypt: introduce retries on in-kernel send CPRB functions
s390/ap: introduce mutex to lock the AP bus scan
s390/ap: rework ap_scan_bus() to return true on config change
s390/ap: clarify AP scan bus related functions and variables
s390/ap: rearm APQNs bindings complete completion
s390/configs: increase number of LOCKDEP_BITS
s390/vfio-ap: handle hardware checkstop state on queue reset operation
s390/pai: change sampling event assignment for PMU device driver
s390/boot: fix minor comment style damages
s390/boot: do not check for zero-termination relocation entry
s390/boot: make type of __vmlinux_relocs_64_start|end consistent
s390/boot: sanitize kaslr_adjust_relocs() function prototype
s390/boot: simplify GOT handling
s390: vmlinux.lds.S: fix .got.plt assertion
s390/boot: workaround current 'llvm-objdump -t -j ...' behavior
...
|
|
The signature for __iowrite64_copy() requires the number of 64 bit
quantities, not bytes. Multiple by 8 to get to a byte length before
invoking zpci_memcpy_toio()
Fixes: 87bc359b9822 ("s390/pci: speed up __iowrite64_copy by using pci store block insn")
Acked-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Jason Gunthorpe <jgg@nvidia.com>
Link: https://lore.kernel.org/r/0-v1-9223d11a7662+1d7785-s390_iowrite64_jgg@nvidia.com
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Found and fixed these while working on synchronizing the state
handling of zpci_dev's.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Centralize the removal so all paths are covered and the hotplug slot
will remain active until the device is really destroyed.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
There's a number of tasks that need the state of a zpci device
to be stable. Other tasks need to be synchronized as they change the state.
State changes could be generated by the system as availability or error
events, or be requested by the user through manipulations in sysfs.
Some other actions accessible through sysfs - like device resets - need the
state to be stable.
Unsynchronized state handling could lead to unusable devices. This has
been observed in cases of concurrent state changes through systemd udev
rules and DPM boot control. Some breakage can be provoked by artificial
tests, e.g. through repetitively injecting "recover" on a PCI function
through sysfs while running a "hotplug remove/add" in a loop through a
PCI slot's "power" attribute in sysfs. After a few iterations this could
result in a kernel oops.
So introduce a new mutex "state_lock" to guard the state property of the
struct zpci_dev. Acquire this lock in all task that modify the state:
- hotplug add and remove, through the PCI hotplug slot entry,
- avaiability events, as reported by the platform,
- error events, as reported by the platform,
- during device resets, explicit through sysfs requests or
implict through the common PCI layer.
Break out an inner _do_recover() routine out of recover_store() to
separte the necessary synchronizations from the actual manipulations of
the zpci_dev required for the reset.
With the following changes I was able to run the inject loops for hours
without hitting an error.
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
Since this guards only the Function Measurement Block, rename from
generic lock to fmb_lock in preparation to introduce another lock
that guards the state member
Signed-off-by: Gerd Bayer <gbayer@linux.ibm.com>
Reviewed-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Heiko Carstens <hca@linux.ibm.com>
|
|
The zpci_get_max_write_size() helper is used to determine the maximum
size a PCI store or load can use at a given __iomem address.
For the PCI block store the following restrictions apply:
1. The dst + len must not cross a 4K boundary in the (pseudo-)MMIO space
2. len must not exceed ZPCI_MAX_WRITE_SIZE
3. len must be a multiple of 8 bytes
4. The src address must be double word (8 byte) aligned
5. The dst address must be double word (8 byte) aligned
Otherwise only a normal PCI store which takes its src value from
a register can be used. For these PCI store restriction 1 still applies.
Similarly 1 also applies to PCI loads.
It turns out zpci_max_write_size() instead implements stricter
conditions which prevents PCI block stores from being used where they
can and should be used. In particular instead of conditions 4 and 5 it
wrongly enforces both dst and src to be size aligned. This indirectly
covers condition 1 but also prevents many legal PCI block stores.
On top of the functional shortcomings the zpci_get_max_write_size() is
misnamed as it is used for both read and write size calculations. Rename
it to zpci_get_max_io_size() and implement the listed conditions
explicitly.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Fixes: cd24834130ac ("s390/pci: base support")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
[agordeev@linux.ibm.com replaced spaces with tabs]
Signed-off-by: Alexander Gordeev <agordeev@linux.ibm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
"Core changes:
- Make default-domains mandatory for all IOMMU drivers
- Remove group refcounting
- Add generic_single_device_group() helper and consolidate drivers
- Cleanup map/unmap ops
- Scaling improvements for the IOVA rcache depot
- Convert dart & iommufd to the new domain_alloc_paging()
ARM-SMMU:
- Device-tree binding update:
- Add qcom,sm7150-smmu-v2 for Adreno on SM7150 SoC
- SMMUv2:
- Support for Qualcomm SDM670 (MDSS) and SM7150 SoCs
- SMMUv3:
- Large refactoring of the context descriptor code to move the CD
table into the master, paving the way for '->set_dev_pasid()'
support on non-SVA domains
- Minor cleanups to the SVA code
Intel VT-d:
- Enable debugfs to dump domain attached to a pasid
- Remove an unnecessary inline function
AMD IOMMU:
- Initial patches for SVA support (not complete yet)
S390 IOMMU:
- DMA-API conversion and optimized IOTLB flushing
And some smaller fixes and improvements"
* tag 'iommu-updates-v6.7' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (102 commits)
iommu/dart: Remove the force_bypass variable
iommu/dart: Call apple_dart_finalize_domain() as part of alloc_paging()
iommu/dart: Convert to domain_alloc_paging()
iommu/dart: Move the blocked domain support to a global static
iommu/dart: Use static global identity domains
iommufd: Convert to alloc_domain_paging()
iommu/vt-d: Use ops->blocked_domain
iommu/vt-d: Update the definition of the blocking domain
iommu: Move IOMMU_DOMAIN_BLOCKED global statics to ops->blocked_domain
Revert "iommu/vt-d: Remove unused function"
iommu/amd: Remove DMA_FQ type from domain allocation path
iommu: change iommu_map_sgtable to return signed values
iommu/virtio: Add __counted_by for struct viommu_request and use struct_size()
iommu/vt-d: debugfs: Support dumping a specified page table
iommu/vt-d: debugfs: Create/remove debugfs file per {device, pasid}
iommu/vt-d: debugfs: Dump entry pointing to huge page
iommu/vt-d: Remove unused function
iommu/arm-smmu-v3-sva: Remove bond refcount
iommu/arm-smmu-v3-sva: Remove unused iommu_sva handle
iommu/arm-smmu-v3: Rename cdcfg to cd_table
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux
Pull s390 updates from Vasily Gorbik:
- Get rid of private VM_FAULT flags
- Add word-at-a-time implementation
- Add DCACHE_WORD_ACCESS support
- Cleanup control register handling
- Disallow CPU hotplug of CPU 0 to simplify its handling complexity,
following a similar restriction in x86
- Optimize pai crypto map allocation
- Update the list of crypto express EP11 coprocessor operation modes
- Fixes and improvements for secure guests AP pass-through
- Several fixes to address incorrect page marking for address
translation with the "cmma no-dat" feature, preventing potential
incorrect guest TLB flushes
- Fix early IPI handling
- Several virtual vs physical address confusion fixes
- Various small fixes and improvements all over the code
* tag 's390-6.7-1' of git://git.kernel.org/pub/scm/linux/kernel/git/s390/linux: (74 commits)
s390/cio: replace deprecated strncpy with strscpy
s390/sclp: replace deprecated strncpy with strtomem
s390/cio: fix virtual vs physical address confusion
s390/cio: export CMG value as decimal
s390: delete the unused store_prefix() function
s390/cmma: fix handling of swapper_pg_dir and invalid_pg_dir
s390/cmma: fix detection of DAT pages
s390/sclp: handle default case in sclp memory notifier
s390/pai_crypto: remove per-cpu variable assignement in event initialization
s390/pai: initialize event count once at initialization
s390/pai_crypto: use PERF_ATTACH_TASK define for per task detection
s390/mm: add missing arch_set_page_dat() call to gmap allocations
s390/mm: add missing arch_set_page_dat() call to vmem_crst_alloc()
s390/cmma: fix initial kernel address space page table walk
s390/diag: add missing virt_to_phys() translation to diag224()
s390/mm,fault: move VM_FAULT_ERROR handling to do_exception()
s390/mm,fault: remove VM_FAULT_BADMAP and VM_FAULT_BADACCESS
s390/mm,fault: remove VM_FAULT_SIGNAL
s390/mm,fault: remove VM_FAULT_BADCONTEXT
s390/mm,fault: simplify kfence fault handling
...
|
|
Since the fixed commits both zdev->iommu_bitmap and zdev->lazy_bitmap
are allocated as vzalloc(zdev->iommu_pages / 8). The problem is that
zdev->iommu_bitmap is a pointer to unsigned long but the above only
yields an allocation that is a multiple of sizeof(unsigned long) which
is 8 on s390x if the number of IOMMU pages is a multiple of 64.
This in turn is the case only if the effective IOMMU aperture is
a multiple of 64 * 4K = 256K. This is usually the case and so didn't
cause visible issues since both the virt_to_phys(high_memory) reduced
limit and hardware limits use nice numbers.
Under KVM, and in particular with QEMU limiting the IOMMU aperture to
the vfio DMA limit (default 65535), it is possible for the reported
aperture not to be a multiple of 256K however. In this case we end up
with an iommu_bitmap whose allocation is not a multiple of
8 causing bitmap operations to access it out of bounds.
Sadly we can't just fix this in the obvious way and use bitmap_zalloc()
because for large RAM systems (tested on 8 TiB) the zdev->iommu_bitmap
grows too large for kmalloc(). So add our own bitmap_vzalloc() wrapper.
This might be a candidate for common code, but this area of code will
be replaced by the upcoming conversion to use the common code DMA API on
s390 so just add a local routine.
Fixes: 224593215525 ("s390/pci: use virtual memory for iommu bitmap")
Fixes: 13954fd6913a ("s390/pci_dma: improve lazy flush for unmap")
Cc: stable@vger.kernel.org
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Together with enabling the Function Measurement Block
zpci_fmb_enable_device() also resets the software counters. This allows
to use "echo 0 > /sys/kernel/debug/pci/<dev>/statistics" followed by
echo "1 > /../statistics" to reset all counters. In commit c76c067e488c
("s390/pci: Use dma-iommu layer") this use of the now obsolete counters
in struct zpci_device was missed as was their removal. Fix this by
resetting the new counters and removing the old ones.
Fixes: c76c067e488c ("s390/pci: Use dma-iommu layer")
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Link: https://lore.kernel.org/r/20231004-dma_iommu_fix-v1-1-129777cd8232@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
While s390 already has a standard IOMMU driver and previous changes have
added I/O TLB flushing operations this driver is currently only used for
user-space PCI access such as vfio-pci. For the DMA API s390 instead
utilizes its own implementation in arch/s390/pci/pci_dma.c which drives
the same hardware and shares some code but requires a complex and
fragile hand over between DMA API and IOMMU API use of a device and
despite code sharing still leads to significant duplication and
maintenance effort. Let's utilize the common code DMAP API
implementation from drivers/iommu/dma-iommu.c instead allowing us to
get rid of arch/s390/pci/pci_dma.c.
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230928-dma_iommu-v13-3-9e5fc4dacc36@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
With the IOMMU always controlled through the IOMMU driver testing for
zdev->s390_domain is not a valid indication of the device being
passed-through. Instead test if zdev->kzdev is set.
Reviewed-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Matthew Rosato <mjrosato@linux.ibm.com>
Signed-off-by: Niklas Schnelle <schnelle@linux.ibm.com>
Link: https://lore.kernel.org/r/20230928-dma_iommu-v13-2-9e5fc4dacc36@linux.ibm.com
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
