| Age | Commit message (Collapse) | Author |
|---|
|
Enable the watchdog timer on the Spider board.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/b36b2bb5770e10d906571721a3d73ca205b6f56e.1642525158.git.geert+renesas@glider.be
|
|
Add a device node for the RCLK Watchdog Timer (RWDT) on the Renesas
R-Car S4-8 (R8A779F0) SoC.
Extracted from a larger patch in the BSP by LUU HOAI.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/556a7f41bdadceecbe8b59b79ac7e9f592ca17a2.1642525158.git.geert+renesas@glider.be
|
|
Replaces KASAN_SANITIZE with KCSAN_SANITIZE in
boot/compressed/Makefile.
Fixes: e0a8b93efa23 mips: Enable KCSAN
Signed-off-by: Nemanja Rakovic <nemanja.rakovic@syrmia.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The only usage of ar2315_pci_irq_domain_ops is to pass its address to
irq_domain_add_linear() which takes a pointer to const struct
irq_domain_ops. Make it const to allow the compiler to put it in
read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The only usage of these structs is to pass their address to either
irq_domain_add_tree() or irq_domain_create_linear(), both which takes
pointers to const struct irq_domain_ops. Make them const to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The only usage of these structs is to pass their address to either
irq_domain_add_tree() or irq_domain_create_linear(), both which takes
pointers to const struct irq_domain_ops. Make them const to allow the
compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Add missing __user annotations to fix sparse errors.
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
The major part for workaround handling has already moved to config
options. This change replaces the remaining defines by already
available config options and gets rid of war.h
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Correct a typo/pasto: setnocoherentio() should set
dma_default_coherent to false, not true.
Fixes: 14ac09a65e19 ("MIPS: refactor the runtime coherent vs noncoherent DMA indicators")
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Cc: Christoph Hellwig <hch@lst.de>
Cc: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
Cc: linux-mips@vger.kernel.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tsbogend@alpha.franken.de>
|
|
Check that size is not zero, preventing the following warning:
WARNING: CPU: 0 PID: 9692 at mm/vmalloc.c:3059 __vmalloc_node_range+0x528/0x648
Modules linked in:
CPU: 0 PID: 9692 Comm: memop Not tainted 5.17.0-rc3-e4+ #80
Hardware name: IBM 8561 T01 701 (LPAR)
Krnl PSW : 0704c00180000000 0000000082dc584c (__vmalloc_node_range+0x52c/0x648)
R:0 T:1 IO:1 EX:1 Key:0 M:1 W:0 P:0 AS:3 CC:0 PM:0 RI:0 EA:3
Krnl GPRS: 0000000000000083 ffffffffffffffff 0000000000000000 0000000000000001
0000038000000000 000003ff80000000 0000000000000cc0 000000008ebb8000
0000000087a8a700 000000004040aeb1 000003ffd9f7dec8 000000008ebb8000
000000009d9b8000 000000000102a1b4 00000380035afb68 00000380035afaa8
Krnl Code: 0000000082dc583e: d028a7f4ff80 trtr 2036(41,%r10),3968(%r15)
0000000082dc5844: af000000 mc 0,0
#0000000082dc5848: af000000 mc 0,0
>0000000082dc584c: a7d90000 lghi %r13,0
0000000082dc5850: b904002d lgr %r2,%r13
0000000082dc5854: eb6ff1080004 lmg %r6,%r15,264(%r15)
0000000082dc585a: 07fe bcr 15,%r14
0000000082dc585c: 47000700 bc 0,1792
Call Trace:
[<0000000082dc584c>] __vmalloc_node_range+0x52c/0x648
[<0000000082dc5b62>] vmalloc+0x5a/0x68
[<000003ff8067f4ca>] kvm_arch_vm_ioctl+0x2da/0x2a30 [kvm]
[<000003ff806705bc>] kvm_vm_ioctl+0x4ec/0x978 [kvm]
[<0000000082e562fe>] __s390x_sys_ioctl+0xbe/0x100
[<000000008360a9bc>] __do_syscall+0x1d4/0x200
[<0000000083618bd2>] system_call+0x82/0xb0
Last Breaking-Event-Address:
[<0000000082dc5348>] __vmalloc_node_range+0x28/0x648
Other than the warning, there is no ill effect from the missing check,
the condition is detected by subsequent code and causes a return
with ENOMEM.
Fixes: ef11c9463ae0 (KVM: s390: Add vm IOCTL for key checked guest absolute memory access)
Signed-off-by: Janis Schoetterl-Glausch <scgl@linux.ibm.com>
Link: https://lore.kernel.org/r/20220221163237.4122868-1-scgl@linux.ibm.com
Signed-off-by: Christian Borntraeger <borntraeger@linux.ibm.com>
|
|
In the i.MX6QP sabresd board(sch-28857) design, one external oscillator
is powered up by vgen3 and used as the PCIe reference clock source by
the endpoint device.
If RC uses this oscillator as reference clock too, PLL6(ENET PLL) would
has to be in bypass mode, and ENET clocks would be messed up.
To keep things simple, let RC use the internal PLL as reference clock
and set vgen3 always on to enable the external oscillator for endpoint
device on i.MX6QP sabresd board.
NOTE: This reference clock setup is used to pass the GEN2 TX compliance
tests, and isn't recommended as a setup in the end-user design.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
When handling reset and power-off PSCI calls from the guest, we
initialise X0 to PSCI_RET_INTERNAL_FAILURE in case the VMM tries to
re-run the vCPU after issuing the call.
Unfortunately, this also means that the VMM cannot see which PSCI call
was issued and therefore cannot distinguish between PSCI SYSTEM_RESET
and SYSTEM_RESET2 calls, which is necessary in order to determine the
validity of the "reset_type" in X1.
Allocate bit 0 of the previously unused 'flags' field of the
system_event structure so that we can indicate the PSCI call used to
initiate the reset.
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220221153524.15397-4-will@kernel.org
|
|
PSCI v1.1 introduces the optional SYSTEM_RESET2 call, which allows the
caller to provide a vendor-specific "reset type" and "cookie" to request
a particular form of reset or shutdown.
Expose this call to the guest and handle it in the same way as PSCI
SYSTEM_RESET, along with some basic range checking on the type argument.
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220221153524.15397-3-will@kernel.org
|
|
Expose PSCI version v1.1 to the guest by default. The only difference
for now is that an updated version number is reported by PSCI_VERSION.
Cc: Marc Zyngier <maz@kernel.org>
Cc: James Morse <james.morse@arm.com>
Cc: Alexandru Elisei <alexandru.elisei@arm.com>
Cc: Suzuki K Poulose <suzuki.poulose@arm.com>
Signed-off-by: Will Deacon <will@kernel.org>
Signed-off-by: Marc Zyngier <maz@kernel.org>
Link: https://lore.kernel.org/r/20220221153524.15397-2-will@kernel.org
|
|
The kgdb code needs to register an undef hook for the Thumb UDF
instruction that will fault in order to be functional on Thumb2
platforms.
Reported-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Johannes Stezenbach <js@sig21.net>
Fixes: 5cbad0ebf45c ("kgdb: support for ARCH=arm")
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
|
|
When an application accesses a mapped frame buffer backed by deferred
I/O, it receives a segmentation fault. Fix this by removing the check
for VM_IO in do_page_fault().
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Tested-by: Michael Schmitz <schmitzmic@gmail.com>
Link: https://lore.kernel.org/r/20220128173006.1713210-1-geert@linux-m68k.org
|
|
To avoid 'warning: no previous prototype for' errors, declare all the
parse_bootinfo and config function prototypes into asm/config.h and
include it in arch/m68k/kernel/setup_mm.c and arch/m68k/*/config.c.
Signed-off-by: Laurent Vivier <laurent@vivier.eu>
Link: https://lore.kernel.org/r/20220121200738.2577697-2-laurent@vivier.eu
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
New conflicts in sched/core due to the following upstream fixes:
44585f7bc0cb ("psi: fix "defined but not used" warnings when CONFIG_PROC_FS=n")
a06247c6804f ("psi: Fix uaf issue when psi trigger is destroyed while being polled")
Conflicts:
include/linux/psi_types.h
kernel/sched/psi.c
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
While Juno's SCP firmware initially spoke the SCPI protocol, binary
releases since 2018, and the newer open-source codebase, only speak SCMI
and thus aren't particularly compatibile with the DTs we currently have
upstream. Add a parallel set of variant DTs for boards with up-to-date
firmware, replacing the SCPI parts with their new SCMI equivalents.
Link: https://lore.kernel.org/r/f3516815104f951a05fc0f799681f77d7968f6ac.1645125063.git.robin.murphy@arm.com
Signed-off-by: Robin Murphy <robin.murphy@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
|
|
reporting
With unprivileged eBPF enabled, eIBRS (without retpoline) is vulnerable
to Spectre v2 BHB-based attacks.
When both are enabled, print a warning message and report it in the
'spectre_v2' sysfs vulnerabilities file.
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Thanks to the chaps at VUsec it is now clear that eIBRS is not
sufficient, therefore allow enabling of retpolines along with eIBRS.
Add spectre_v2=eibrs, spectre_v2=eibrs,lfence and
spectre_v2=eibrs,retpoline options to explicitly pick your preferred
means of mitigation.
Since there's new mitigations there's also user visible changes in
/sys/devices/system/cpu/vulnerabilities/spectre_v2 to reflect these
new mitigations.
[ bp: Massage commit message, trim error messages,
do more precise eIBRS mode checking. ]
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Patrick Colp <patrick.colp@oracle.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
The RETPOLINE_AMD name is unfortunate since it isn't necessarily
AMD only, in fact Hygon also uses it. Furthermore it will likely be
sufficient for some Intel processors. Therefore rename the thing to
RETPOLINE_LFENCE to better describe what it is.
Add the spectre_v2=retpoline,lfence option as an alias to
spectre_v2=retpoline,amd to preserve existing setups. However, the output
of /sys/devices/system/cpu/vulnerabilities/spectre_v2 will be changed.
[ bp: Fix typos, massage. ]
Co-developed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Josh Poimboeuf <jpoimboe@redhat.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Signed-off-by: Borislav Petkov <bp@suse.de>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Fix comment referencing salvator board, likely a copy-paste leftover.
ulcb-kf.dtsi has nothing to do with salvator.
Signed-off-by: Nikita Yushchenko <nikita.yoush@cogentembedded.com>
Fixes: 80c07701d5918928 ("arm64: dts: renesas: ulcb-kf: add pcm3168 sound codec")
Link: https://lore.kernel.org/r/20220216181003.114049-1-nikita.yoush@cogentembedded.com
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
The OSMC Vero 4K+ device is based on the Amlogic S905D (P230)
reference design with the following specifications:
- 2GB DDR4 RAM
- 16GB eMMC
- HDMI 2.1 video
- S/PDIF optical output
- AV output
- 10/100/1000 Ethernet
- AP6255 Wireless (802.11 a/b/g/n/ac, BT 4.2)
- 2x USB 2.0 ports (1x OTG)
- IR receiver (internal)
- IR extender port (external)
- 1x micro SD card slot
- 1x Power LED (red)
- 1x Reset button (in AV jack)
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Tested-by: Chad Wagner <wagnerch42@gmail.com>
Reviewed-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Link: https://lore.kernel.org/r/20220211105311.30320-4-christianshewitt@gmail.com
|
|
witherspoon hardware and p9 chips have very sensitive requirements for
the cfam-reset. We're seeing power faults with the kernel based cfam
reset due to this.
Could adapt the power application to use the new kernel based cfam reset
interface but there's not a lot to be gained there since the power
application is going away with p10 and this limitation is not present in
p10.
Signed-off-by: Eddie James <eajames@linux.ibm.com>
Link: https://lore.kernel.org/r/20210308225419.46530-17-eajames@linux.ibm.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Set the usdhc root clock to 400MHz to be able to support
HS400/HS400ES modes for eMMC on phyCORE-i.MX8MP SoM.
Signed-off-by: Jonas Kuenstler <j.kuenstler@phytec.de>
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
LDO4 is not connected so disable it. And LDO5 is used for VSEL of
the NVCC_SD2 SD-Card bus. Having it disabled seems not to have an
impact on the functionality. We enable it, as it is used.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add bindings for VDD_ARM (BUCK2) run and standby voltage.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To be able to trigger a reset also from an external source we
need to configure the WDOG pin as open drain.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Reduce drive strength on fec tx lines for signal quality improvements.
Measurements showed that TD0 and TD1 require X4 and the other lines
X2 for optimized settings.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Set eMMC drive strength for USDHC3_DATA lines (200Mhz)
to X4 for signal improvement.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Reviewed-by: Haibo Chen <haibo.chen@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
To fit spec requirements set minimum output impedance for dp83867
ethernet phy.
Signed-off-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
- https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
- has its own on-board 24MHz osc so no clock required from baseboard
- pin 11 enables 1.8V and 2.8V LDO which is connected to
GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio
Support is added via a device-tree overlay.
The IMX219 supports RAW8/RAW10 image formats.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add support for the RaspberryPi Camera v2 which is an IMX219 8MP module:
- https://datasheets.raspberrypi.com/camera/camera-v2-schematics.pdf
- has its own on-board 24MHz osc so no clock required from baseboard
- pin 11 enables 1.8V and 2.8V LDO which is connected to
GW73xx MIPI_GPIO4 (IMX8MM GPIO1_IO1) so we use this as a gpio
controlled regulator enable.
Support is added via a device-tree overlay.
The IMX219 supports RAW8/RAW10 image formats.
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx8mm-venice-gw72xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.
The default configuration per the imx8mm-venice-gw72xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
J15.1 UART2 TX out
J15.2 UART2 RX in
J15.3 UART4 TX out
J15.4 UART4 RX in
J15.5 GND
Add dt overlays to allow additional the modes of operation:
rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
J15.1 TX out
J15.2 RX in
J15.3 RTS out
J15.4 CTS in
J15.5 GND
rs485 (UART2 RS-485 half duplex)
J15.1 TXRX-
J15.2 N/C
J15.3 TXRX+
J15.4 N/C
J15.5 GND
rs422 (UART2 RS-422 full duplex)
J15.1 TX-
J15.2 RX+
J15.3 TX+
J15.4 RX-
J15.5 GND
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The imx8mm-venice-gw73xx-0x som+baseboard combination has a multi-protocol
RS-232/RS-485/RS-422 transceiver to an off-board connector which
can be configured in a number of ways via UART and GPIO configuration.
The default configuration per the imx8mm-venice-gw73xx-0x dts is for
UART2 TX/RX and UART4 TX/RX to be available as RS-232:
J15.1 UART2 TX out
J15.2 UART2 RX in
J15.3 UART4 TX out
J15.4 UART4 RX in
J15.5 GND
Add dt overlays to allow additional the modes of operation:
rs232-rts (UART2 RS-232 with RTS/CTS hardware flow control)
J15.1 TX out
J15.2 RX in
J15.3 RTS out
J15.4 CTS in
J15.5 GND
rs485 (UART2 RS-485 half duplex)
J15.1 TXRX-
J15.2 N/C
J15.3 TXRX+
J15.4 N/C
J15.5 GND
rs422 (UART2 RS-422 full duplex)
J15.1 TX-
J15.2 RX+
J15.3 TX+
J15.4 RX-
J15.5 GND
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The GW7903 is based on the i.MX 8M Mini SoC featuring:
- LPDDR4 DRAM
- eMMC FLASH
- microSD connector with UHS support
- LIS2DE12 3-axis accelerometer
- Gateworks System Controller
- IMX8M FEC
- software selectable RS232/RS485/RS422 serial transceiver
- PMIC
- 2x off-board bi-directional opto-isolated digital I/O
- 1x M.2 A-E Key Socket and 1x MiniPCIe socket with USB2.0 and PCIe
(resistor loading to route PCIe/USB2 between M.2 and MiniPCIe socket)
Signed-off-by: Tim Harvey <tharvey@gateworks.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Layerscape SoCs contain a Security Fuse Processor which is basically a
efuse controller. Add the node, so userspace can read the efuses.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This GPIO is used on the rainier system to indicate the BMC was reset
due to a physical pinhole reset.
See the following doc for more information:
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Link: https://lore.kernel.org/r/20220113211735.37861-1-geissonator@yahoo.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
This GPIO is used on the everest system to indicate the BMC was reset
due to a physical pinhole reset.
It has been verified that the previous name for this pin has not been
utilized by userspace so the name change is ok.
See the following doc for more information:
https://github.com/openbmc/docs/blob/master/designs/device-tree-gpio-naming.md
Signed-off-by: Andrew Geissler <geissonator@yahoo.com>
Link: https://lore.kernel.org/r/20220113211735.37861-2-geissonator@yahoo.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Make the Tacoma KCS nodes reflect the configuration of the Rainier and
Everest nodes.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210709151119.2683600-1-andrew@aj.id.au
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
Add support for i2c5, which is used to access the
external I2C bus on connector J22 of the imx8mp-evk.
Limit the speed to 100kHz since this is an external I2C bus.
Disabled by default, since it is shared with the CAN1 bus.
To enable i2c5, you need to disable the CAN1 function, enable the i2c5
function and also configure the CAN1/I2C5_SEL GPIO to HIGH to
select i2c5 instead of CAN1. This can be done by defining a gpio-hog
inside the pca6416 node, in your board device tree, like in this example:
&flexcan1 {
status = "disabled";
};
&i2c5 {
status = "okay";
};
&pca6416 {
can1-i2c5-sel-hog {
gpio-hog;
gpios = <2 GPIO_ACTIVE_HIGH>;
output-high;
line-name = "can1-i2c5-sel";
};
};
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add gpio-line-names for the various GPIO's connected to the PCA6416
I/O expander on the imx8mp EVK.
This helps when using the new gpiod interface to find the GPIOs by name.
Signed-off-by: Hugo Villeneuve <hvilleneuve@dimonoff.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add more serial alias to imx8qm.dtsi file
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
add compatible string for usdhc3
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: devicetree@vger.kernel.org
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Oliver Graute <oliver.graute@kococonnector.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The Quanta S6Q is a server platform with AST2600 BMC SoC
Signed-off-by: George Hung <george.hung@quantatw.com>
Reviewed-by: Alan Kuo <Alan_Kuo@quantatw.com>
Reviewed-by: P.K. Lee <p.k.lee@quantatw.com>
Link: https://lore.kernel.org/r/20220217031355.46102-1-george.hung@quantatw.com
Signed-off-by: Joel Stanley <joel@jms.id.au>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 fixes from Borislav Petkov:
- Fix the ptrace regset xfpregs_set() callback to behave according to
the ABI
- Handle poisoned pages properly in the SGX reclaimer code
* tag 'x86_urgent_for_v5.17_rc5' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/ptrace: Fix xfpregs_set()'s incorrect xmm clearing
x86/sgx: Fix missing poison handling in reclaimer
|
|
This patch enables support for PREEMPT_DYNAMIC on arm64, allowing the
preemption model to be chosen at boot time.
Specifically, this patch selects HAVE_PREEMPT_DYNAMIC_KEY, so that each
preemption function is an out-of-line call with an early return
depending upon a static key. This leaves almost all the codegen up to
the compiler, and side-steps a number of pain points with static calls
(e.g. interaction with CFI schemes). This should have no worse overhead
than using non-inline static calls, as those use out-of-line trampolines
with early returns.
For example, the dynamic_cond_resched() wrapper looks as follows when
enabled. When disabled, the first `B` is replaced with a `NOP`,
resulting in an early return.
| <dynamic_cond_resched>:
| bti c
| b <dynamic_cond_resched+0x10> // or `nop`
| mov w0, #0x0
| ret
| mrs x0, sp_el0
| ldr x0, [x0, #8]
| cbnz x0, <dynamic_cond_resched+0x8>
| paciasp
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl <preempt_schedule_common>
| mov w0, #0x1
| ldp x29, x30, [sp], #16
| autiasp
| ret
... compared to the regular form of the function:
| <__cond_resched>:
| bti c
| mrs x0, sp_el0
| ldr x1, [x0, #8]
| cbz x1, <__cond_resched+0x18>
| mov w0, #0x0
| ret
| paciasp
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl <preempt_schedule_common>
| mov w0, #0x1
| ldp x29, x30, [sp], #16
| autiasp
| ret
Since arm64 does not yet use the generic entry code, we must define our
own `sk_dynamic_irqentry_exit_cond_resched`, which will be
enabled/disabled by the common code in kernel/sched/core.c. All other
preemption functions and associated static keys are defined there.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20220214165216.2231574-8-mark.rutland@arm.com
|
|
For historical reasons, the decision of whether or not to preempt is
spread across arm64_preempt_schedule_irq() and __el1_irq(), and it would
be clearer if this were all in one place.
Also, arm64_preempt_schedule_irq() calls lockdep_assert_irqs_disabled(),
but this is redundant, as we have a subsequent identical assertion in
__exit_to_kernel_mode(), and preempt_schedule_irq() will
BUG_ON(!irqs_disabled()) anyway.
This patch removes the redundant assertion and centralizes the
preemption decision making within arm64_preempt_schedule_irq().
Other than the slight change to assertion behaviour, there should be no
functional change as a result of this patch.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Catalin Marinas <catalin.marinas@arm.com>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20220214165216.2231574-7-mark.rutland@arm.com
|
|
Where an architecture selects HAVE_STATIC_CALL but not
HAVE_STATIC_CALL_INLINE, each static call has an out-of-line trampoline
which will either branch to a callee or return to the caller.
On such architectures, a number of constraints can conspire to make
those trampolines more complicated and potentially less useful than we'd
like. For example:
* Hardware and software control flow integrity schemes can require the
addition of "landing pad" instructions (e.g. `BTI` for arm64), which
will also be present at the "real" callee.
* Limited branch ranges can require that trampolines generate or load an
address into a register and perform an indirect branch (or at least
have a slow path that does so). This loses some of the benefits of
having a direct branch.
* Interaction with SW CFI schemes can be complicated and fragile, e.g.
requiring that we can recognise idiomatic codegen and remove
indirections understand, at least until clang proves more helpful
mechanisms for dealing with this.
For PREEMPT_DYNAMIC, we don't need the full power of static calls, as we
really only need to enable/disable specific preemption functions. We can
achieve the same effect without a number of the pain points above by
using static keys to fold early returns into the preemption functions
themselves rather than in an out-of-line trampoline, effectively
inlining the trampoline into the start of the function.
For arm64, this results in good code generation. For example, the
dynamic_cond_resched() wrapper looks as follows when enabled. When
disabled, the first `B` is replaced with a `NOP`, resulting in an early
return.
| <dynamic_cond_resched>:
| bti c
| b <dynamic_cond_resched+0x10> // or `nop`
| mov w0, #0x0
| ret
| mrs x0, sp_el0
| ldr x0, [x0, #8]
| cbnz x0, <dynamic_cond_resched+0x8>
| paciasp
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl <preempt_schedule_common>
| mov w0, #0x1
| ldp x29, x30, [sp], #16
| autiasp
| ret
... compared to the regular form of the function:
| <__cond_resched>:
| bti c
| mrs x0, sp_el0
| ldr x1, [x0, #8]
| cbz x1, <__cond_resched+0x18>
| mov w0, #0x0
| ret
| paciasp
| stp x29, x30, [sp, #-16]!
| mov x29, sp
| bl <preempt_schedule_common>
| mov w0, #0x1
| ldp x29, x30, [sp], #16
| autiasp
| ret
Any architecture which implements static keys should be able to use this
to implement PREEMPT_DYNAMIC with similar cost to non-inlined static
calls. Since this is likely to have greater overhead than (inlined)
static calls, PREEMPT_DYNAMIC is only defaulted to enabled when
HAVE_PREEMPT_DYNAMIC_CALL is selected.
Signed-off-by: Mark Rutland <mark.rutland@arm.com>
Signed-off-by: Peter Zijlstra (Intel) <peterz@infradead.org>
Acked-by: Ard Biesheuvel <ardb@kernel.org>
Acked-by: Frederic Weisbecker <frederic@kernel.org>
Link: https://lore.kernel.org/r/20220214165216.2231574-6-mark.rutland@arm.com
|
