| Age | Commit message (Collapse) | Author |
|---|
|
Move to generic channels binding to ease new backend framework adoption
and prepare the convergence with MDF IP support on STM32MP2 SoC family.
Legacy binding:
DFSDM is an IIO channel consumer.
SD modulator is an IIO channels provider.
The channel phandles are provided in DT through io-channels property
and channel indexes through st,adc-channels property.
New binding:
DFSDM is an IIO channel provider.
The channel indexes are given by reg property in channel child node.
This new binding is intended to be used with SD modulator IIO backends.
It does not support SD modulator legacy IIO devices.
The st,adc-channels property presence is used to discriminate
between legacy and backend bindings.
The support of the DFSDM legacy channels and SD modulator IIO devices
is kept for backward compatibility.
Signed-off-by: Olivier Moysan <olivier.moysan@foss.st.com>
Link: https://patch.msgid.link/20240730084640.1307938-8-olivier.moysan@foss.st.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The cfg pointer is set before reading the channel number that the
configuration should point to. This causes configurations to be shifted
by one channel.
For example setting bipolar to the first channel defined in the DT will
cause bipolar mode to be active on the second defined channel.
Fix by moving the cfg pointer setting after reading the channel number.
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240806085133.114547-1-dumitru.ceclan@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
With commit 7b0c9f8fa3d2 ("iio: adc: ad_sigma_delta: Add optional irq
selection"), we can get the irq line from struct ad_sigma_delta_info
instead of the spi device. However, in devm_ad_sd_probe_trigger(), when
getting the irq_flags with irq_get_trigger_type() we are still using
the spi device irq instead of the one used for devm_request_irq().
Fixes: 7b0c9f8fa3d2 ("iio: adc: ad_sigma_delta: Add optional irq selection")
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240806-dev-fix-ad-sigma-delta-v1-1-aa25b173c063@analog.com
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Remove IRQF_TRIGGER_FALLING flag from irq request, this should come from
the platform firmware and should not be hard-coded into the driver.
Add IRQF_ONESHOT flag to the irq request, the interrupt should not be
re-activated in interrupt context, it should be done only after the
device irq handler run.
Fixes: a9306887eba4 ("iio: adc: ti-ads1119: Add driver")
Signed-off-by: Francesco Dolcini <francesco.dolcini@toradex.com>
Reviwed-by: João Paulo Gonçalves <jpaulo.silvagoncalves@gmail.com>
Link: https://patch.msgid.link/20240731140657.88265-1-francesco@dolcini.it
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
During setup the st->adc_control is 0, which corresponds to a continuous
conversion mode. The reset value for channel 1 is to enable it. The
combined effect of these two is that the ADC will start conversions for
channel 1 without them being read.
This is not neccessarily a problem, but it is an unexpected behavior.
Set the ADC state to idle during setup to avoid this.
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240731-ad7124-fix-v1-4-46a76aa4b9be@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad7124_init_config_vref() function writes the AD7124_ADC_CONTROL
register for each channel that is configured to use the internal
reference.
The ad7124_write_config()function performs 7 SPI transfers for
configuring 2 registers: config_x and filter_x.
Reduce the number of SPI transfers:
-during the probe by only setting the st->adc_control value in
ad7124_init_config_vref() and writing to the device only at the end of
ad7124_setup().
-in ad7124_write_config() by grouping writes to the same register.
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240731-ad7124-fix-v1-3-46a76aa4b9be@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad7124_find_similar_live_cfg() computes the compare size by
substracting the address of the cfg struct from the address of the live
field. Because the live field is the first field in the struct, the
result is 0.
Also, the memcmp() call is made from the start of the cfg struct, which
includes the live and cfg_slot fields, which are not relevant for the
comparison.
Fix by grouping the relevant fields with struct_group() and use the
size of the group to compute the compare size; make the memcmp() call
from the address of the group.
Fixes: 7b8d045e497a ("iio: adc: ad7124: allow more than 8 channels")
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240731-ad7124-fix-v1-2-46a76aa4b9be@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
The ad7124_soft_reset() function has the assumption that the chip will
assert the "power-on reset" bit in the STATUS register after a software
reset without any delay. The POR bit =0 is used to check if the chip
initialization is done.
A chip ID mismatch probe error appears intermittently when the probe
continues too soon and the ID register does not contain the expected
value.
Fix by adding a 200us delay after the software reset command is issued.
Fixes: b3af341bbd96 ("iio: adc: Add ad7124 support")
Signed-off-by: Dumitru Ceclan <dumitru.ceclan@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240731-ad7124-fix-v1-1-46a76aa4b9be@analog.com
Cc: <Stable@vger.kernel.org>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
One useful thing to do (in case of problems) in this high speed devices
with digital interfaces is to try different test patterns to see if the
interface is working properly (and properly calibrated). Hence add this
to debugfs.
On top of this, for some test patterns, the backend may have a matching
validator block which can be helpful in identifying possible issues. For
the other patterns some test equipment must be used so one can look into
the signal and see how it looks like.
Hence, we also add the backend debugfs interface with
iio_backend_debugfs_add().
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-8-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Group the backend configurations to be done in preparing and stopping
calibration in two new helpers analogous to ad9467_testmode_set(). This
is in preparation for adding support for debugFS test_mode where
we need similar configurations as in the calibration process.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-7-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Implement debugfs options to read/write registers and print the channel
status into a buffer (so we may know better the cause for errors) .
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-6-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add a new axi_adc_read_chan_status() helper so we get the raw register
value out of it.
This is in preparation of a future change where we really want to look
into dedicated bits of the register.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-5-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for configuring the prbs23 sequence.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-4-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Instead of only passing the backend ops when calling
devm_iio_backend_register(), pass an info like structure that will
contains the ops and additional information. Fow now, the backend name
is being added as that will be used by the debugFS interface introduced
in a later patch.
It also opens the door for further customizations passed by backends.
All users of devm_iio_backend_register() were updated accordingly.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240802-dev-iio-backend-add-debugfs-v2-1-4cb62852f0d0@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use of_property_present() to test for property presence rather than
of_find_property(). This is part of a larger effort to remove callers
of of_find_property() and similar functions. of_find_property() leaks
the DT struct property and data pointers which is a problem for
dynamically allocated nodes which may be freed.
Signed-off-by: Rob Herring (Arm) <robh@kernel.org>
Acked-by: Andrew Jeffery <andrew@codeconstruct.com.au>
Link: https://patch.msgid.link/20240731191312.1710417-5-robh@kernel.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Drop the manual access to the fwnode of the device to iterate over its
child nodes. `device_for_each_child_node` macro provides direct access
to the child nodes, and given that they are only required within the
loop, the scoped variant of the macro can be used.
Use the `device_for_each_child_node_scoped` macro to iterate over the
direct child nodes of the device.
Signed-off-by: Javier Carrasco <javier.carrasco.cruz@gmail.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240801-device_child_node_access-v1-2-ddfa21bef6f2@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ad7386/7/8(-4) single-ended parts have a 2:1 mux in front of each ADC.
>From an IIO point of view, all inputs are exported, i.e ad7386/7/8
export 4 channels and ad7386-4/7-4/8-4 export 8 channels. First inputs
of muxes correspond to the first half of IIO channels (i.e 0-1 or 0-3)
and second inputs correspond to second half (i.e 2-3 or 4-7)
Currently, the driver supports only sampling first half OR second half of
the IIO channels. To enable sampling all channels simultaneously, these
parts have an internal sequencer that automatically cycles through the
mux entries.
When enabled, the maximum throughput is divided by two. Moreover, the ADCs
need additional settling time, so we add an extra CS toggle to correctly
propagate setting, and an additional spi transfer to read the second
half.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240731-ad7380-add-single-ended-chips-v2-6-cd63bf05744c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Adding ad7386/7/8 (16/14/12 bits) unsigned, dual simultaneous sampling,
single-ended compatible parts, and the corresponding ad7386-4/7-4/8-4
4 channels.
These parts have a 2:1 multiplexer in front of each ADC. They also include
additional configuration registers that allow for either manual selection
or automatic switching (sequencer mode), of the multiplexer inputs.
This commit focus on integrating manual selection. Sequencer mode will
be implemented later.
>From an IIO point of view, all inputs are exported, i.e ad7386/7/8
export 4 channels and ad7386-4/7-4/8-4 export 8 channels.
Inputs AinX0 of multiplexers correspond to the first half of IIO channels
(i.e 0-1 or 0-3) and inputs AinX1 correspond to second half (i.e 2-3 or
4-7). Example for AD7386/7/8 (2 channels parts):
IIO | AD7386/7/8
| +----------------------------
| | _____ ______
| | | | | |
voltage0 | AinA0 --|--->| | | |
| | | mux |----->| ADCA |---
voltage2 | AinA1 --|--->| | | |
| | |_____| |_____ |
| | _____ ______
| | | | | |
voltage1 | AinB0 --|--->| | | |
| | | mux |----->| ADCB |---
voltage3 | AinB1 --|--->| | | |
| | |_____| |______|
| |
| +----------------------------
When switching channel, the ADC require an additional settling time.
According to the datasheet, data is valid on the third CS low. We already
have an extra toggle before each read (either direct reads or buffered
reads) to sample correct data, so we just add a single CS toggle at the
end of the register write.
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240731-ad7380-add-single-ended-chips-v2-5-cd63bf05744c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
ad738x family contains single-ended parts that have a 2:1 mux in front
of ADC, so the number of IIO channels is different from the number of
simultaneous channels that can be sampled.
To prepare the support for single-ended parts, introduce a new
num_simultaneous_channels variable. For currently supported parts,
num_simultaneous_channels is equal to num_channels minus 1 (the
timestamps channel)
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240731-ad7380-add-single-ended-chips-v2-4-cd63bf05744c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add missing trailing commas in iio_scan_type structures
Signed-off-by: Julien Stephan <jstephan@baylibre.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Link: https://patch.msgid.link/20240731-ad7380-add-single-ended-chips-v2-3-cd63bf05744c@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for AD4000 series of low noise, low power, high speed,
successive approximation register (SAR) ADCs.
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: David Lechner <dlechner@baylibre.com>
Signed-off-by: Marcelo Schmitt <marcelo.schmitt@analog.com>
Link: https://patch.msgid.link/356109ac61182f16f2379d5d0cadccfe017f505b.1720810545.git.marcelo.schmitt@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use devm_regulator_get_enable_read_voltage() to replace
tsc2046_adc_configure_regulator() which does the same thing.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240725-iio-regulator-refactor-round-4-v1-1-55e9dc1de325@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Add support for Microchip PAC1921 Power/Current monitor.
Implemented features:
* capture of bus voltage, sense voltage, current and power measurements
in free-run integration mode
* support for both raw and triggered buffer reading
* support for overflow events
* scale attributes to control voltage and current gains
* oversampling ratio attribute to control the number of integration
samples
* sampling rate attribute that reflects the integration period
* userspace attribute and DT parameter to control shunt resistor
* simple power management support
Limitations:
* operation mode fixed to free-run integration
* READ/INT pin and OUT pin not supported
* no controls for measurement resolutions and filters
Signed-off-by: Matteo Martelli <matteomartelli3@gmail.com>
Link: https://patch.msgid.link/20240724-iio-pac1921-v4-3-723698e903a3@gmail.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes use of the new devm_regulator_get_enable_read_voltage()
helper function to reduce boilerplate code in the MCP3564 ADC driver.
The error message is slightly changed since there are fewer error
return paths.
Setting adc->vref_mv is consolidated into a single place to make the
logic easier to follow.
A use_internal_vref_attr local variable is added to make it more
obvious what the difference between the two iio info structures is.
The return value of the "Unknown Vref" dev_err_probe() is hard-coded to
-ENODEV instead of ret since it was getting a bit far from where ret
was set and logically that is the only value it could have.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marius Cristea <marius.cristea@microchip.com>
Link: https://patch.msgid.link/20240723-iio-regulator-refactor-round-3-v2-1-ae9291201785@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-20-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_get_masklength() to access '.masklength' so it can be annotated
as __private when there are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-19-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-18-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-17-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-16-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-15-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-14-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_get_masklength() to access '.masklength' so it can be annotated
as __private when there are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: João Paulo Gonçalves <jpaulo.silvagoncalves@gmail.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-13-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_get_masklength() to access '.masklength' so it can be annotated
as __private when there are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-12-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-11-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-10-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_get_masklength() to access '.masklength' so it can be annotated
as __private when there are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-9-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_get_masklength() to access '.masklength' so it can be annotated
as __private when there are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-8-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-7-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Acked-by: Heiko Stuebner <heiko@sntech.de>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-6-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-5-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-4-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-3-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240726-dev-iio-masklength-private3-v1-2-82913fc0fb87@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240718-dev-iio-masklength-private2-v1-3-8e12cd042906@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Make use of iio_get_masklength) and iio_for_each_active_channel() to
access '.masklength' so it can be annotated as __private when there
are no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240718-dev-iio-masklength-private2-v1-2-8e12cd042906@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Use iio_for_each_active_channel() to iterate over active channels
accessing '.masklength' so it can be annotated as __private when there are
no more direct users of it.
Signed-off-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240718-dev-iio-masklength-private2-v1-1-8e12cd042906@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
Internal clock of AD719X devices can be made available on MCLK2 pin. Add
clock provider to support this functionality when clock cells property
is present.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240717212535.8348-5-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
There are actually 4 configuration modes of clock source for AD719X
devices. Either a crystal can be attached externally between MCLK1 and
MCLK2 pins, or an external CMOS-compatible clock can drive the MCLK2
pin. The other 2 modes make use of the 4.92MHz internal clock.
Undocumented properties adi,int-clock-output-enable and adi,clock-xtal
still supported for backward compatibility, but their use is highly
discouraged. Use cleaner alternative of configuring external clock by
using clock names mclk and xtal.
Functionality of AD7192_CLK_INT_CO will be implemented in complementary
patch by adding clock provider.
Signed-off-by: Alisa-Dariana Roman <alisa.roman@analog.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240717212535.8348-3-alisa.roman@analog.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This makes use of the new devm_regulator_get_enable_read_voltage()
helper function to reduce boilerplate code in the MCP3911 ADC driver.
The error message is slightly changed since there are fewer error
return paths.
An extra parameter is added to the config callback to avoid adding
state that is not used outside of the probe() function.
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Link: https://patch.msgid.link/20240712-iio-regulator-refactor-round-3-v1-6-835017bae43d@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
|
This is a new driver for Analog Devices Inc. AD4695 and similar ADCs.
The initial driver supports initializing the chip including configuring
all possible LDO and reference voltage sources as well as any possible
voltage input channel wiring configuration.
Only the 4-wire SPI wiring mode where the CNV pin is tied to the CS pin
is supported at this time. And reading sample data from the ADC can only
be done in direct mode for now.
Co-developed-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Signed-off-by: Ramona Gradinariu <ramona.gradinariu@analog.com>
Signed-off-by: David Lechner <dlechner@baylibre.com>
Reviewed-by: Nuno Sa <nuno.sa@analog.com>
Link: https://patch.msgid.link/20240711-iio-adc-ad4695-v4-2-c31621113b57@baylibre.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
|
