| Age | Commit message (Collapse) | Author |
|---|
|
Add NULL check before variable dereference to fix static checker warning.
Fixes: d76d22b5096c ("mtd: rawnand: cadence: use dma_map_resource for sdma address")
Reported-by: Dan Carpenter <dan.carpenter@linaro.org>
Closes: https://lore.kernel.org/all/e448a22c-bada-448d-9167-7af71305130d@stanley.mountain/
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix broken config in qcom_param_page_type_exec caused by copy-paste error
from commit 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
In qcom_param_page_type_exec the value needs to be set to
nandc->regs->cfg0 instead of host->cfg0. This wrong configuration caused
the Qcom NANDC driver to malfunction on any device that makes use of it
(IPQ806x, IPQ40xx, IPQ807x, IPQ60xx) with the following error:
[ 0.885369] nand: device found, Manufacturer ID: 0x2c, Chip ID: 0xaa
[ 0.885909] nand: Micron NAND 256MiB 1,8V 8-bit
[ 0.892499] nand: 256 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64
[ 0.896823] nand: ECC (step, strength) = (512, 8) does not fit in OOB
[ 0.896836] qcom-nandc 79b0000.nand-controller: No valid ECC settings possible
[ 0.910996] bam-dma-engine 7984000.dma-controller: Cannot free busy channel
[ 0.918070] qcom-nandc: probe of 79b0000.nand-controller failed with error -28
Restore original configuration fix the problem and makes the driver work
again.
Also restore the wrongly dropped cpu_to_le32 to correctly support BE
systems.
Cc: stable@vger.kernel.org
Fixes: 0c08080fd71c ("mtd: rawnand: qcom: use FIELD_PREP and GENMASK")
Tested-by: Robert Marko <robimarko@gmail.com> # IPQ8074 and IPQ6018
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
dma_map_single is using physical/bus device (DMA) but dma_unmap_single
is using framework device(NAND controller), which is incorrect.
Fixed dma_unmap_single to use correct physical/bus device.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Remap the slave DMA I/O resources to enhance driver portability.
Using a physical address causes DMA translation failure when the
ARM SMMU is enabled.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Replace dma_request_channel() with dma_request_chan_by_mask() and use
helper functions to return proper error code instead of fixed -EBUSY.
Fixes: ec4ba01e894d ("mtd: rawnand: Add new Cadence NAND driver to MTD subsystem")
Cc: stable@vger.kernel.org
Signed-off-by: Niravkumar L Rabara <niravkumar.l.rabara@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The SPINAND_PAGE_READ_FROM_CACHE_OP macro has just been changed to stop
encoding the "fast" parameter (the macro has been duplicated and
renamed). The Skyhigh driver is new and is still using the old style
macro.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202501161302.bQqBGjJ5-lkp@intel.com/
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Closes: https://lore.kernel.org/linux-kernel/20250116132010.4948547d@canb.auug.org.au/
Fixes: 042087247835d ("mtd: spinand: Create distinct fast and slow read from cache variants")
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Tested-by: Stephen Rothwell <sfr@canb.auug.org.au> # build tested
|
|
W25N01JW and W25N02JW support many DTR read modes in single, dual and
quad configurations.
DTR modes however cannot be used at 166MHz, as the bus frequency in
this case must be lowered to 80MHz.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Make the link between the core macros and the datasheet.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
W25N01JW and W25N02JW use a different technology with higher frequencies
supported (up to 166MHz). There is one drawback though, the slowest
READ_FROM_CACHE command cannot run above 54MHz. Because of that, we need
to set a limit for these chips on the basic READ_FROM_CACHE variant.
Duplicating this list is not a problem because these chips have DTR
support, and the list of supported variants will diverge from all the
other chips when adding support for it.
Cc: stable+noautosel@kernel.org # New feature being added
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently the best variant picked in the first one in the list provided
in the manufacturer driver. This worked well while all operations where
performed at the same speed, but with the introduction of DTR transfers
and per operation maximum frequencies, this no longer works correctly.
Let's continue iterating over all the alternatives, even if we find a
match, keeping a reference over the theoretically fastest
operation. Only at the end we can tell which variant is the best.
This logic happening only once at boot, the extra computing needed
compared to the previous version is acceptable wrt. the expected
improvements.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
So far, the SPINAND_PAGE_READ_FROM_CACHE_OP macro was taking a first
argument, "fast", which was inducing the possibility to support higher
bus frequencies than with the normal (slower) read from cache
alternative. In practice, without frequency change on the bus, this was
likely without effect, besides perhaps allowing another variant of the
same command, that could run at the default highest speed. If we want to
support this fully, we need to add a frequency parameter to the slowest
command. But before we do that, let's drop the "fast" boolean from the
macro and duplicate it, this will further help supporting having
different frequencies allowed for each variant.
The change is also of course propagated to all users. It has the nice
effect to have all macros aligned on the same pattern.
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
spi: Support DTR in spi-mem
Changes to support DTR with spi-mem.
|
|
Add support for the OOB layout used by the ROM bootloader.
The same layout is used by both Keystone [1] and OMAPL138/DA850 [2]
which currently is the only users of davinci-nand.
Only select this layout if the `nand-is-boot-medium` property is set.
This to avoid breaking any existing devices out there.
[1] https://www.ti.com/lit/ug/spruhj3/spruhj3.pdf
[2] https://www.ti.com/lit/an/sprab41f/sprab41f.pdf
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
In the spi subsystem, the bus frequency is derived as follows:
- the controller may expose a minimum and maximum operating frequency
- the hardware description, through the spi peripheral properties,
advise what is the maximum acceptable frequency from a device/wiring
point of view.
Transfers must be observed at a frequency which fits both (so in
practice, the lowest maximum).
Actually, this second point mixes two information and already takes the
lowest frequency among:
- what the spi device is capable of (what is written in the component
datasheet)
- what the wiring allows (electromagnetic sensibility, crossovers,
terminations, antenna effect, etc).
This logic works until spi devices are no longer capable of sustaining
their highest frequency regardless of the operation. Spi memories are
typically subject to such variation. Some devices are capable of
spitting their internally stored data (essentially in read mode) at a
very fast rate, typically up to 166MHz on Winbond SPI-NAND chips, using
"fast" commands. However, some of the low-end operations, such as
regular page read-from-cache commands, are more limited and can only be
executed at 54MHz at most. This is currently a problem in the SPI-NAND
subsystem. Another situation, even if not yet supported, will be with
DTR commands, when the data is latched on both edges of the clock. The
same chips as mentioned previously are in this case limited to
80MHz. Yet another example might be continuous reads, which, under
certain circumstances, can also run at most at 104 or 120MHz.
As a matter of fact, the "one frequency per chip" policy is outdated and
more fine grain configuration is needed: we need to allow per-operation
frequency limitations. So far, all datasheets I encountered advertise a
maximum default frequency, which need to be lowered for certain specific
operations. So based on the current infrastructure, we can still expect
firmware (device trees in general) to continued advertising the same
maximum speed which is a mix between the PCB limitations and the chip
maximum capability, and expect per-operation lower frequencies when this
is relevant.
Add a `struct spi_mem_op` member to carry this information. Not
providing this field explicitly from upper layers means that there is no
further constraint and the default spi device maximum speed will be
carried instead. The SPI_MEM_OP() macro is also expanded with an
optional frequency argument, because virtually all operations can be
subject to such a limitation, and this will allow for a smooth and
discrete transition.
For controller drivers which do not implement the spi-mem interface, the
per-transfer speed is also set acordingly to a lower (than the maximum
default) speed when relevant.
Acked-by: Pratyush Yadav <pratyush@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://patch.msgid.link/20241224-winbond-6-11-rc1-quad-support-v2-1-ad218dbc406f@bootlin.com
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
For each NAND_OP_WAITRDY_INSTR operation, the NANDFSR register is
polled only once every 100 us to check for the EMA_WAIT pin. This
isn't frequent enough and causes delays in NAND accesses.
Set the polling interval to 5 us. It increases the page read speed
reported by flash_speed by ~30% (~10% on page writes).
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fix a buffer overflow issue in qcom_clear_bam_transaction by using
struct_group to group related fields and avoid FORTIFY_SOURCE warnings.
On x86 architecture, the following error occurs due to warnings being
treated as errors:
In function ‘fortify_memset_chk’,
inlined from ‘qcom_clear_bam_transaction’ at
drivers/mtd/nand/qpic_common.c:88:2:
./include/linux/fortify-string.h:480:25: error: call to ‘__write_overflow_field’
declared with attribute warning: detected write beyond size of field
(1st parameter); maybe use struct_group()? [-Werror=attribute-warning]
480 | __write_overflow_field(p_size_field, size);
| ^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
LD [M] drivers/mtd/nand/nandcore.o
CC [M] drivers/w1/masters/mxc_w1.o
cc1: all warnings being treated as errors
This patch addresses the issue by grouping the related fields in
struct bam_transaction using struct_group and updating the memset call
accordingly.
Fixes: 8c52932da5e6 ("mtd: rawnand: qcom: cleanup qcom_nandc driver")
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Topic branch with preparation changes from Qcom in order to apply on top
the spi bits adding the Qcom SPI-NAND controller driver re-using a lot
of code that has been shared.
With this goal in mind, the raw NAND controller driver has been cleaned
up and reorganized, and only the relevant structures/helpers which have
nothing raw NAND specific should now be exported.
|
|
Use the bitfield macro FIELD_PREP, and GENMASK to
do the shift and mask in one go. This makes the code
more readable.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add qpic_common.c file which hold all the common
qpic APIs which will be used by both qpic raw nand
driver and qpic spi nand driver.
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add qcom prefix to all the api which will be commonly
used by spi nand driver and raw nand driver.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Perform a global cleanup of the Qualcomm NAND
controller driver with the following improvements:
- Remove register value indirection API
- Remove set_reg() API
- Convert read_loc_first & read_loc_last macro to functions
- Rename multiple variables
Signed-off-by: Md Sadre Alam <quic_mdalam@quicinc.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The setup_interface() operation isn't implemented. It forces the driver
to use the ONFI mode 0, though it could use more optimal modes.
Implement the setup_interface() operation. It uses the
aemif_set_cs_timings() function from the AEMIF driver to update the
chip select timings. The calculation of the register's contents is
directly extracted from §20.3.2.3 of the DaVinci TRM [1]
MAX_TH_PS and MAX_TSU_PS are the worst case timings based on the
Keystone2 and DaVinci datasheets.
[1] : https://www.ti.com/lit/ug/spruh77c/spruh77c.pdf
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
NAND controller has a reference clock inherited from the AEMIF
(cf. Documentation/devicetree/bindings/memory-controllers/ti-aemif.txt)
This clock isn't used yet by the driver.
Add a struct clock in the struct davinci_nand_info so it can be used
to compute timings.
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
DAVINCI_NAND depends on TI_AEMIF only when ARCH_KEYSTONE is selected
while the NAND controller is also always a part of the AEMIF controller
on DaVinci SoCs.
Set a dependency on TI_AEMIF regardless of the selected architecture.
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202411020140.3wsKJOSB-lkp@intel.com/
Closes: https://lore.kernel.org/oe-kbuild-all/202411020957.X1T8T9ZR-lkp@intel.com/
Signed-off-by: Bastien Curutchet <bastien.curutchet@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Nuvoton MA35 SoCs NAND Flash Interface Controller
supports 2kiB, 4kiB and 8kiB page size, and up to
8-bit, 12-bit, and 24-bit hardware ECC calculation
circuit to protect data.
Signed-off-by: Hui-Ping Chen <hpchen0nvt@gmail.com>
[Miquel Raynal: Fixed compatible and driver name to match latest bindings]
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
This change fixes an issue where an error return value may be mistakenly
used as NAND status.
Fixes: f504551b7f15 ("mtd: rawnand: Propagate error and simplify ternary operators for brcmstb_nand_wait_for_completion()")
Signed-off-by: david regan <dregan@broadcom.com>
Reviewed-by: William Zhang <william.zhang@broadcom.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add kernel-doc for functions to get rid of below warnings
when built with W=1.
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:260: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:304: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:446: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_in_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'chip' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'buf' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'len' not described in 'omap_nand_data_out_dma_pref'
drivers/mtd/nand/raw/omap2.c:467: warning: Function parameter or struct member 'force_8bit' not described in 'omap_nand_data_out_dma_pref'
Reported-by: kernel test robot <lkp@intel.com>
Closes: https://lore.kernel.org/oe-kbuild-all/202412031716.JfNIh1Uu-lkp@intel.com/
Signed-off-by: Roger Quadros <rogerq@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SkyHigh S35ML01G300, S35ML01G301, S35ML02G300, and S35ML04G300 are 1Gb,
2Gb, and 4Gb SLC SPI NAND flash family. This family of devices has
on-die ECC which parity bits are stored to hidden area. In this family
the on-die ECC cannot be disabled so raw access needs to be prevented.
Link: https://www.skyhighmemory.com/download/SPI_S35ML01_04G3_002_19205.pdf?v=P
Co-developed-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: KR Kim <kr.kim@skyhighmemory.com>
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
SkyHigh spinand device has ECC enable bit in configuration register but
it must be always enabled. If ECC is disabled, read and write ops
results in undetermined state. For such devices, a way to avoid raw
access is needed.
Introduce SPINAND_NO_RAW_ACCESS flag to advertise the device does not
support raw access. In such devices, the on-die ECC engine ops returns
error to I/O request in raw mode.
Checking and marking BBM need to be cared as special case, by adding
fallback mechanism that tries read/write OOB with ECC enabled.
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
We don't have to call spinand_write_enable_op() in spinand_markbad() as
it is called in spinand_write_page().
Fixes: b645ad39d568 ("mtd: spinand: Do not erase the block before writing a bad block marker")
Signed-off-by: Takahiro Kuwano <Takahiro.Kuwano@infineon.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The NAND chip-selects are registered for the Arasan driver during
initialization but are not de-registered when the driver is unloaded. As a
result, if the driver is loaded again, the chip-selects remain registered
and busy, making them unavailable for use.
Fixes: 197b88fecc50 ("mtd: rawnand: arasan: Add new Arasan NAND controller")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski ICEYE <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
When two chip-selects are configured in the device tree, and the second is
a non-native GPIO, both the GPIO-based chip-select and the first native
chip-select may be asserted simultaneously. This double assertion causes
incorrect read and write operations.
The issue occurs because when nfc->ncs <= 2, nfc->spare_cs is always
initialized to 0 due to static initialization. Consequently, when the
second chip-select (GPIO-based) is selected in anfc_assert_cs(), it is
detected by anfc_is_gpio_cs(), and nfc->native_cs is assigned the value 0.
This results in both the GPIO-based chip-select being asserted and the
NAND controller register receiving 0, erroneously selecting the native
chip-select.
This patch resolves the issue, as confirmed by oscilloscope testing with
configurations involving two or more chip-selects in the device tree.
Fixes: acbd3d0945f9 ("mtd: rawnand: arasan: Leverage additional GPIO CS")
Cc: stable@vger.kernel.org
Signed-off-by: Maciej Andrzejewski <maciej.andrzejewski@m-works.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The function do_otp_read() does not set the output parameter *retlen,
which is expected to contain the number of bytes actually read.
As a result, in onenand_otp_walk(), the tmp_retlen variable remains
uninitialized after calling do_otp_walk() and used to change
the values of the buf, len and retlen variables.
Found by Linux Verification Center (linuxtesting.org) with SVACE.
Fixes: 49dc08eeda70 ("[MTD] [OneNAND] fix numerous races")
Cc: stable@vger.kernel.org
Signed-off-by: Ivan Stepchenko <sid@itb.spb.ru>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add support for FORESEE F35SQA001G SPI NAND.
Similar to F35SQA002G, but differs in capacity.
Datasheet:
- https://cdn.ozdisan.com/ETicaret_Dosya/704795_871495.pdf
Tested on Xiaomi AX3000T flashed with OpenWRT.
Signed-off-by: Bohdan Chubuk <chbgdn@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
There may be a potential integer overflow issue in inftl_partscan().
parts[0].size is defined as "uint64_t" while mtd->erasesize and
ip->firstUnit are defined as 32-bit unsigned integer. The result of
the calculation will be limited to 32 bits without correct casting.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Zichen Xie <zichenxie0106@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Some chips, e.g. Micron MT29F1G08ABBFAH4, has a mandatory on-die ECC.
Add "on-die" as ECC engine type in order to be compatible with those.
Signed-off-by: Marcus Folkesson <marcus.folkesson@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The "user" pointer was converted from being allocated with kzalloc() to
being allocated by devm_kzalloc(). Calling kfree(user) will lead to a
double free.
Fixes: 6d734f1bfc33 ("mtd: rawnand: atmel: Fix possible memory leak")
Signed-off-by: Dan Carpenter <dan.carpenter@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD device changes:
- switch platform_driver back to remove()
- misc fixes
SPI-NAND changes:
- a load of fixes to Winbond manufacturer driver
- structure constification
Raw NAND changes:
- improve the power management of the GPMI driver
- Davinci driver clean-ups
- fix leak in the Atmel driver
- fix some typos in the core
SPI NOR changes:
- Introduce byte swap support for 8D-8D-8D mode and a user for it:
macronix.
SPI NOR flashes may swap the bytes on a 16-bit boundary when
configured in Octal DTR mode. For such cases the byte order is
propagated through SPI MEM to the SPI controllers so that the
controllers swap the bytes back at runtime. This avoids breaking
the boot sequence because of the endianness problems that appear
when the bootloaders use 1-1-1 and the kernel uses 8D-8D-8D with
byte swap support. Along with the SPI MEM byte swap support we
queue a patch for the SPI MXIC controller that swaps the bytes back
at runtime"
* tag 'mtd/for-6.13' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (25 commits)
mtd: spi-nor: core: replace dummy buswidth from addr to data
mtd: spi-nor: winbond: add "w/ and w/o SFDP" comment
mtd: spi-nor: spansion: Use nor->addr_nbytes in octal DTR mode in RD_ANY_REG_OP
mtd: Switch back to struct platform_driver::remove()
mtd: cfi_cmdset_0002: remove redundant assignment to variable ret
mtd: spinand: Constify struct nand_ecc_engine_ops
MAINTAINERS: add mailing list for GPMI NAND driver
mtd: spinand: winbond: Sort the devices
mtd: spinand: winbond: Ignore the last ID characters
mtd: spinand: winbond: Fix 512GW, 01GW, 01JW and 02JW ECC information
mtd: spinand: winbond: Fix 512GW and 02JW OOB layout
mtd: nand: raw: gpmi: improve power management handling
mtd: nand: raw: gpmi: switch to SYSTEM_SLEEP_PM_OPS
mtd: rawnand: davinci: use generic device property helpers
mtd: rawnand: davinci: break the line correctly
mtd: rawnand: davinci: order headers alphabetically
mtd: rawnand: atmel: Fix possible memory leak
mtd: rawnand: Correct multiple typos in comments
mtd: hyperbus: rpc-if: Add missing MODULE_DEVICE_TABLE
mtd: spi-nor: add support for Macronix Octal flash
...
|
|
SPI-NAND changes:
A load of fixes to Winbond manufacturer driver have been done, plus a
structure constification.
Raw NAND changes:
The GPMI driver has been improved on the power management side.
The Davinci driver has been cleaned up.
A leak in the Atmel driver plus some typos in the core have been fixed.
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/mtd to use .remove(), with
the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007205803.444994-10-u.kleine-koenig@baylibre.com
|
|
'struct nand_ecc_engine_ops' are not modified in these drivers.
Constifying this structure moves some data to a read-only section, so
increases overall security, especially when the structure holds some
function pointers.
Update the prototype of mxic_ecc_get_pipelined_ops() accordingly.
On a x86_64, with allmodconfig, as an example:
Before:
======
text data bss dec hex filename
16709 1374 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
After:
=====
text data bss dec hex filename
16789 1294 16 18099 46b3 drivers/mtd/nand/ecc-mxic.o
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/72597e9de2320a4109be2112e696399592edacd4.1729271136.git.christophe.jaillet@wanadoo.fr
|
|
Use alphabetical order, not because it's pretty, but because it makes
sense. This way the devices are listed by density, and then by hardware
feature set. Add comments to make the list more understandable.
There is no intended functional change.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-5-miquel.raynal@bootlin.com
|
|
The last 4 characters in Winbond's branding indicate:
- the package type (ZE/SF/TB),
- the temperature grade (I/J),
- special options, typically the continuous read vs. page read feature
support and its default (G/T/F/R),
None of these information impact us, at the software level (well, the
continuous read mode by default is impacting, but is already handled
gracefully by disabling it in the initialization phase), so let's get
rid of it.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-4-miquel.raynal@bootlin.com
|
|
These four chips:
* W25N512GW
* W25N01GW
* W25N01JW
* W25N02JW
all require a single bit of ECC strength and thus feature an on-die
Hamming-like ECC engine. There is no point in filling a ->get_status()
callback for them because the main ECC status bytes are located in
standard places, and retrieving the number of bitflips in case of
corrected chunk is both useless and unsupported (if there are bitflips,
then there is 1 at most, so no need to query the chip for that).
Without this change, a kernel warning triggers every time a bit flips.
Fixes: 6a804fb72de5 ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-3-miquel.raynal@bootlin.com
|
|
Both W25N512GW and W25N02JW chips have 64 bytes of OOB and thus cannot
use the layout for 128 bytes OOB. Reference the correct layout instead.
Fixes: 6a804fb72de5 ("mtd: spinand: winbond: add support for serial NAND flash")
Cc: stable@vger.kernel.org
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Reviewed-by: Frieder Schrempf <frieder.schrempf@kontron.de>
Link: https://lore.kernel.org/linux-mtd/20241009125002.191109-2-miquel.raynal@bootlin.com
|
|
Refactor the power management handling in the gpmi nand driver. Remove
redundant pm_runtime calls in the driver probe function. Handle the pad
control and use the leverage runtime suspend and resume calls to take
care of clocks in system suspend and resume functions.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007191319.220775-2-han.xu@nxp.com
|
|
Replace the SET_SYSTEM_SLEEP_PM_OPS with modern SYSTEM_SLEEP_PM_OPS
alternatives.
Signed-off-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007191319.220775-1-han.xu@nxp.com
|
|
There's no reason for this driver to be using OF-specific property
accessors. Switch to using generic device property interfaces and
replace the of.h include with property.h. This allows us to no longer
check the existence of the associated of_node.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-3-brgl@bgdev.pl
|
|
The line in nand_davinci_get_pdata() prototype is broken in a weird and
unreadable way. Make it consistent with the rest of the code.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-2-brgl@bgdev.pl
|
|
For better readability, put all includes in alphabetical order.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Link: https://lore.kernel.org/linux-mtd/20241007122350.75285-1-brgl@bgdev.pl
|
