| Age | Commit message (Collapse) | Author |
|---|
|
This was left as TODO in commit 01e23b2b3bad ("net: enetc: add support
for preemptible traffic classes") since it's relatively complicated.
Where this makes a difference is with a configuration as follows:
ethtool --set-mm eno0 pmac-enabled on tx-enabled on verify-enabled on
Preemptible packets should only be sent when the MAC Merge TX direction
becomes active (i.o.w. when the verification process succeeds, aka when
the link partner confirms it can process preemptible traffic). But the
tc qdisc with the preemptible traffic classes is offloaded completely
asynchronously w.r.t. the MM becoming active.
The ENETC manual does suggest that this should be handled in the driver:
"On startup, software should wait for the verification process to
complete (MMCSR[VSTS]=011) before initiating traffic".
Adding the necessary logic allows future selftests to uphold the claim
that an inactive or disabled MAC Merge layer should never send data
packets through the pMAC.
This change moves enetc_set_ptcfpr() from enetc.c to enetc_ethtool.c,
where its only caller is now - enetc_mm_commit_preemptible_tcs().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The MMCSR register contains 2 fields with overlapping meaning:
- LPA (Local preemption active):
This read-only status bit indicates whether preemption is active for
this port. This bit will be set if preemption is both enabled and has
completed the verification process.
- TXSTS (Merge status):
This read-only status field provides the state of the MAC Merge sublayer
transmit status as defined in IEEE Std 802.3-2018 Clause 99.
00 Transmit preemption is inactive
01 Transmit preemption is active
10 Reserved
11 Reserved
However none of these 2 fields offer reliable reporting to software.
When connecting ENETC to a link partner which is not capable of Frame
Preemption, the expectation is that ENETC's verification should fail
(VSTS=4) and its MM TX direction should be inactive (LPA=0, TXSTS=00)
even though the MM TX is enabled (ME=1). But surprise, the LPA bit of
MMCSR stays set even if VSTS=4 and ME=1.
OTOH, the TXSTS field has the opposite problem. I cannot get its value
to change from 0, even when connecting to a link partner capable of
frame preemption, which does respond to its verification frames (ME=1
and VSTS=3, "SUCCEEDED").
The only option with such buggy hardware seems to be to reimplement the
formula for calculating tx-active in software, which is for tx-enabled
to be true, and for the verify-status to be either SUCCEEDED, or
DISABLED.
Without reliable tx-active reporting, we have no good indication when
to commit the preemptible traffic classes to hardware, which makes it
possible (but not desirable) to send preemptible traffic to a link
partner incapable of receiving it. However, currently we do not have the
logic to wait for TX to be active yet, so the impact is limited.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Current enetc_set_mm() is designed to set the priv->active_offloads bit
ENETC_F_QBU for enetc_mm_link_state_update() to act on, but if the link
is already up, it modifies the ENETC_MMCSR_ME ("Merge Enable") bit
directly.
The problem is that it only *sets* ENETC_MMCSR_ME if the link is up, it
doesn't *clear* it if needed. So subsequent enetc_get_mm() calls still
see tx-enabled as true, up until a link down event, which is when
enetc_mm_link_state_update() will get called.
This is not a functional issue as far as I can assess. It has only come
up because I'd like to uphold a simple API rule in core ethtool code:
the pMAC cannot be disabled if TX is going to be enabled. Currently,
the fact that TX remains enabled for longer than expected (after the
enetc_set_mm() call that disables it) is going to violate that rule,
which is how it was caught.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
PFs which support the MAC Merge layer also have a set of 8 registers
called "Port traffic class N frame preemption register (PTC0FPR - PTC7FPR)".
Through these, a traffic class (group of TX rings of same dequeue
priority) can be mapped to the eMAC or to the pMAC.
There's nothing particularly spectacular here. We should probably only
commit the preemptible TCs to hardware once the MAC Merge layer became
active, but unlike Felix, we don't have an IRQ that notifies us of that.
We'd have to sleep for up to verifyTime (127 ms) to wait for a
resolution coming from the verification state machine; not only from the
ndo_setup_tc() code path, but also from enetc_mm_link_state_update().
Since it's relatively complicated and has a relatively small benefit,
I'm not doing it.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
To gain access to the larger encapsulating structure which has the type
tc_mqprio_qopt_offload, rename just the "qopt" field as "qopt".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Ferenc Fejes <fejes@inf.elte.hu>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
tools/testing/selftests/net/config
62199e3f1658 ("selftests: net: Add VXLAN MDB test")
3a0385be133e ("selftests: add the missing CONFIG_IP_SCTP in net config")
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
I have observed an issue where the RX direction of the LS1028A ENETC pMAC
seems unresponsive. The minimal procedure to reproduce the issue is:
1. Connect ENETC port 0 with a loopback RJ45 cable to one of the Felix
switch ports (0).
2. Bring the ports up (MAC Merge layer is not enabled on either end).
3. Send a large quantity of unidirectional (express) traffic from Felix
to ENETC. I tried altering frame size and frame count, and it doesn't
appear to be specific to either of them, but rather, to the quantity
of octets received. Lowering the frame count, the minimum quantity of
packets to reproduce relatively consistently seems to be around 37000
frames at 1514 octets (w/o FCS) each.
4. Using ethtool --set-mm, enable the pMAC in the Felix and in the ENETC
ports, in both RX and TX directions, and with verification on both
ends.
5. Wait for verification to complete on both sides.
6. Configure a traffic class as preemptible on both ends.
7. Send some packets again.
The issue is at step 5, where the verification process of ENETC ends
(meaning that Felix responds with an SMD-R and ENETC sees the response),
but the verification process of Felix never ends (it remains VERIFYING).
If step 3 is skipped or if ENETC receives less traffic than
approximately that threshold, the test runs all the way through
(verification succeeds on both ends, preemptible traffic passes fine).
If, between step 4 and 5, the step below is also introduced:
4.1. Disable and re-enable PM0_COMMAND_CONFIG bit RX_EN
then again, the sequence of steps runs all the way through, and
verification succeeds, even if there was the previous RX traffic
injected into ENETC.
Traffic sent *by* the ENETC port prior to enabling the MAC Merge layer
does not seem to influence the verification result, only received
traffic does.
The LS1028A manual does not mention any relationship between
PM0_COMMAND_CONFIG and MMCSR, and the hardware people don't seem to
know for now either.
The bit that is toggled to work around the issue is also toggled
by enetc_mac_enable(), called from phylink's mac_link_down() and
mac_link_up() methods - which is how the workaround was found:
verification would work after a link down/up.
Fixes: c7b9e8086902 ("net: enetc: add support for MAC Merge layer")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230411192645.1896048-1-vladimir.oltean@nxp.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
A number of MDIO drivers make use of devm_mdiobus_alloc_size(). This
is only available when CONFIG_MDIO_DEVRES is enabled. Add missing
depends or selects, depending on if there are circular dependencies or
not. This avoids linker errors, especially for randconfig builds.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Link: https://lore.kernel.org/r/20230409150204.2346231-1-andrew@lunn.ch
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When running "ethtool -S eno0 --groups rmon" without an explicit "--src
emac|pmac" argument, the kernel will not report
rx-rmon-etherStatsPkts64to64Octets, rx-rmon-etherStatsPkts65to127Octets,
etc. This is because on ETHTOOL_MAC_STATS_SRC_AGGREGATE, we do not
populate the "ranges" argument.
ocelot_port_get_rmon_stats() does things differently and things work
there. I had forgotten to make sure that the code is structured the same
way in both drivers, so do that now.
Fixes: cf52bd238b75 ("net: enetc: add support for MAC Merge statistics counters")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Link: https://lore.kernel.org/r/20230321232831.1200905-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
====================
pull-request: bpf-next 2023-02-11
We've added 96 non-merge commits during the last 14 day(s) which contain
a total of 152 files changed, 4884 insertions(+), 962 deletions(-).
There is a minor conflict in drivers/net/ethernet/intel/ice/ice_main.c
between commit 5b246e533d01 ("ice: split probe into smaller functions")
from the net-next tree and commit 66c0e13ad236 ("drivers: net: turn on
XDP features") from the bpf-next tree. Remove the hunk given ice_cfg_netdev()
is otherwise there a 2nd time, and add XDP features to the existing
ice_cfg_netdev() one:
[...]
ice_set_netdev_features(netdev);
netdev->xdp_features = NETDEV_XDP_ACT_BASIC | NETDEV_XDP_ACT_REDIRECT |
NETDEV_XDP_ACT_XSK_ZEROCOPY;
ice_set_ops(netdev);
[...]
Stephen's merge conflict mail:
https://lore.kernel.org/bpf/20230207101951.21a114fa@canb.auug.org.au/
The main changes are:
1) Add support for BPF trampoline on s390x which finally allows to remove many
test cases from the BPF CI's DENYLIST.s390x, from Ilya Leoshkevich.
2) Add multi-buffer XDP support to ice driver, from Maciej Fijalkowski.
3) Add capability to export the XDP features supported by the NIC.
Along with that, add a XDP compliance test tool,
from Lorenzo Bianconi & Marek Majtyka.
4) Add __bpf_kfunc tag for marking kernel functions as kfuncs,
from David Vernet.
5) Add a deep dive documentation about the verifier's register
liveness tracking algorithm, from Eduard Zingerman.
6) Fix and follow-up cleanups for resolve_btfids to be compiled
as a host program to avoid cross compile issues,
from Jiri Olsa & Ian Rogers.
7) Batch of fixes to the BPF selftest for xdp_hw_metadata which resulted
when testing on different NICs, from Jesper Dangaard Brouer.
8) Fix libbpf to better detect kernel version code on Debian, from Hao Xiang.
9) Extend libbpf to add an option for when the perf buffer should
wake up, from Jon Doron.
10) Follow-up fix on xdp_metadata selftest to just consume on TX
completion, from Stanislav Fomichev.
11) Extend the kfuncs.rst document with description on kfunc
lifecycle & stability expectations, from David Vernet.
12) Fix bpftool prog profile to skip attaching to offline CPUs,
from Tonghao Zhang.
====================
Link: https://lore.kernel.org/r/20230211002037.8489-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PF driver support for the following:
- Viewing the standardized MAC Merge layer counters.
- Viewing the standardized Ethernet MAC and RMON counters associated
with the pMAC.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230206094531.444988-2-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add PF driver support for viewing and changing the MAC Merge sublayer
parameters, and seeing the verification state machine's current state.
The verification handshake with the link partner is driven by hardware.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20230206094531.444988-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We assume that the mqprio queue configuration from taprio has a simple
1:1 mapping between prio and traffic class, and one TX queue per TC.
That might not be the case. Actually parse and act upon the mqprio
config.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Regardless of the requested queue count per traffic class, the enetc
driver allocates a number of TX rings equal to the number of TCs, and
hardcodes a queue configuration of "1@0 1@1 ... 1@max-tc". Other
configurations are silently ignored and treated the same.
Improve that by allowing what the user requests to be actually
fulfilled. This allows more than one TX ring per traffic class.
For example:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 4 \
map 0 0 1 1 2 2 3 3 queues 2@0 2@2 2@4 2@6
[ 146.267648] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 146.273451] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 146.283280] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 1
[ 146.293987] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 1
[ 146.300467] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 2
[ 146.306866] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 2
[ 146.313261] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 3
[ 146.319622] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 3
$ tc qdisc del dev eno0 root
[ 178.238418] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 178.244369] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 0
[ 178.251486] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 0
[ 178.258006] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 0
[ 178.265038] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 0
[ 178.271557] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 0
[ 178.277910] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 0
[ 178.284281] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 0
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
[ 186.113162] fsl_enetc 0000:00:00.0 eno0: TX ring 0 prio 0
[ 186.118764] fsl_enetc 0000:00:00.0 eno0: TX ring 1 prio 1
[ 186.124374] fsl_enetc 0000:00:00.0 eno0: TX ring 2 prio 2
[ 186.130765] fsl_enetc 0000:00:00.0 eno0: TX ring 3 prio 3
[ 186.136404] fsl_enetc 0000:00:00.0 eno0: TX ring 4 prio 4
[ 186.142049] fsl_enetc 0000:00:00.0 eno0: TX ring 5 prio 5
[ 186.147674] fsl_enetc 0000:00:00.0 eno0: TX ring 6 prio 6
[ 186.153305] fsl_enetc 0000:00:00.0 eno0: TX ring 7 prio 7
The driver used to set TC_MQPRIO_HW_OFFLOAD_TCS, near which there is
this comment in the UAPI header:
TC_MQPRIO_HW_OFFLOAD_TCS, /* offload TCs, no queue counts */
which is what enetc was doing up until now (and no longer is; we offload
queue counts too), remove that assignment.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The enetc driver does not validate the mqprio queue configuration, so it
currently allows things like this:
$ tc qdisc add dev swp0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 queues 3@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 hw 1
But also things like this, completely omitting the queue configuration:
$ tc qdisc add dev eno0 root handle 1: mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 hw 1
By requesting validation via the mqprio capability structure, this is no
longer allowed, and we bring what is accepted by hardware in line with
what is accepted by software.
The check that num_tc <= real_num_tx_queues also becomes superfluous and
can be dropped, because mqprio_validate_queue_counts() validates that no
TXQ range exceeds real_num_tx_queues. That is a stronger check, because
there is at least 1 TXQ per TC, so there are at least as many TXQs as TCs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Jacob Keller <jacob.e.keller@intel.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently it can happen that an mqprio qdisc is installed with num_tc 8,
and this will reserve 8 (out of 8) TXQs for the network stack. Then we
can attach an XDP program, and this will crop 2 TXQs, leaving just 6 for
mqprio. That's not what the user requested, and we should fail it.
On the other hand, if mqprio isn't requested, we still give the 8 TXQs
to the network stack (with hashing among a single traffic class), but
then, cropping 2 TXQs for XDP is fine, because the user didn't
explicitly ask for any number of TXQs, so no expectations are violated.
Simply put, the logic that mqprio should impose a minimum number of TXQs
for the network never existed. Let's say (more or less arbitrarily) that
without mqprio, the driver expects a minimum number of TXQs equal to the
number of CPUs (on NXP LS1028A, that is either 1, or 2). And with mqprio,
mqprio gives the minimum required number of TXQs.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Since the blamed net-next commit, enetc_setup_xdp_prog() no longer goes
through enetc_open(), and therefore, the function which was supposed to
detect whether a BPF program exists (in order to crop some TX queues
from network stack usage), enetc_num_stack_tx_queues(), no longer gets
called.
We can move the netif_set_real_num_rx_queues() call to enetc_alloc_msix()
(probe time), since it is a runtime invariant. We can do the same thing
with netif_set_real_num_tx_queues(), and let enetc_reconfigure_xdp_cb()
explicitly recalculate and change the number of stack TX queues.
Fixes: c33bfaf91c4c ("net: enetc: set up XDP program under enetc_reconfigure()")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
enetc_reconfigure() was modified in commit c33bfaf91c4c ("net: enetc:
set up XDP program under enetc_reconfigure()") to take an optional
callback that runs while the netdev is down, but this callback currently
cannot fail.
Code up the error handling so that the interface is restarted with the
old resources if the callback fails.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We keep a pointer to the xdp_prog in the private netdev structure as
well; what's replicated per RX ring is done so just for more convenient
access from the NAPI poll procedure.
Simplify enetc_num_stack_tx_queues() by looking at priv->xdp_prog rather
than iterating through the information replicated per RX ring.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A summary of the flags being set for various drivers is given below.
Note that XDP_F_REDIRECT_TARGET and XDP_F_FRAG_TARGET are features
that can be turned off and on at runtime. This means that these flags
may be set and unset under RTNL lock protection by the driver. Hence,
READ_ONCE must be used by code loading the flag value.
Also, these flags are not used for synchronization against the availability
of XDP resources on a device. It is merely a hint, and hence the read
may race with the actual teardown of XDP resources on the device. This
may change in the future, e.g. operations taking a reference on the XDP
resources of the driver, and in turn inhibiting turning off this flag.
However, for now, it can only be used as a hint to check whether device
supports becoming a redirection target.
Turn 'hw-offload' feature flag on for:
- netronome (nfp)
- netdevsim.
Turn 'native' and 'zerocopy' features flags on for:
- intel (i40e, ice, ixgbe, igc)
- mellanox (mlx5).
- stmmac
- netronome (nfp)
Turn 'native' features flags on for:
- amazon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2, enetc)
- funeth
- intel (igb)
- marvell (mvneta, mvpp2, octeontx2)
- mellanox (mlx4)
- mtk_eth_soc
- qlogic (qede)
- sfc
- socionext (netsec)
- ti (cpsw)
- tap
- tsnep
- veth
- xen
- virtio_net.
Turn 'basic' (tx, pass, aborted and drop) features flags on for:
- netronome (nfp)
- cavium (thunder)
- hyperv.
Turn 'redirect_target' feature flag on for:
- amanzon (ena)
- broadcom (bnxt)
- freescale (dpaa, dpaa2)
- intel (i40e, ice, igb, ixgbe)
- ti (cpsw)
- marvell (mvneta, mvpp2)
- sfc
- socionext (netsec)
- qlogic (qede)
- mellanox (mlx5)
- tap
- veth
- virtio_net
- xen
Reviewed-by: Gerhard Engleder <gerhard@engleder-embedded.com>
Reviewed-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Stanislav Fomichev <sdf@google.com>
Acked-by: Jakub Kicinski <kuba@kernel.org>
Co-developed-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Signed-off-by: Kumar Kartikeya Dwivedi <memxor@gmail.com>
Co-developed-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Signed-off-by: Marek Majtyka <alardam@gmail.com>
Link: https://lore.kernel.org/r/3eca9fafb308462f7edb1f58e451d59209aa07eb.1675245258.git.lorenzo@kernel.org
Signed-off-by: Alexei Starovoitov <ast@kernel.org>
|
|
The pMAC (ENETC_PFPMR_PMACE) is probably unconditionally enabled in the
enetc driver to allow RX of preemptible packets and not see them as
error frames. I don't know why TX preemption (ENETC_MMCSR_ME) is enabled
though. With no way to say which traffic classes are preemptible (all
are express by default), no preemptible frames would be transmitted
anyway.
Lastly, it may have been believed that the register write lock-step mode
(now deleted) needed the pMAC to be enabled at all times. I don't know
if that's true. However, I've checked that driver writes to PM1
registers do propagate through to the ENETC IP even when the pMAC is
disabled.
With such incomplete support for frame preemption, it's best to just
remove whatever exists right now and come with something more coherent
later.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the enetc driver duplicates its writes to the PM0 registers
also to PM1, but it doesn't do this consistently - for example we write
to ENETC_PM0_MAXFRM but not to ENETC_PM1_MAXFRM.
Create enetc_port_mac_wr() which writes both the PM0 and PM1 register
with the same value (if frame preemption is supported on this port).
Also create enetc_port_mac_rd() which reads from PM0 - the assumption
being that PM1 contains just the same value.
This will be necessary when we enable the MAC Merge layer properly, and
the pMAC becomes operational.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MWLM bit (MAC write lock-step mode) allows register writes to the
pMAC to be auto-performed whenever the corresponding eMAC register is
written by the driver. This allows their configuration to remain
in sync.
The driver has set this bit since the initial commit, but it doesn't do
anything, since the hardware feature doesn't work (and the bit has been
removed from more recent versions of the documentation).
The driver does attempt, more or less, to keep those MAC registers in
sync by writing the same value once to e.g. ENETC_PM0_CMD_CFG (eMAC) and
once to ENETC_PM1_CMD_CFG (pMAC). Because the lockstep feature doesn't
work, that's what it will stick to.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a preliminary patch which replaces the hardcoded 0x1000 present
in other PM1 (port MAC 1, aka pMAC) register definitions, which is an
offset to the PM0 (port MAC 0, aka eMAC) equivalent register.
This definition will be used in more places by future code.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similar to other TSN features, query the Station Interface capability
register to see whether preemption is supported on this port or not.
On LS1028A, preemption is available on ports 0 and 2, but not on 1
and 3.
This will allow us in the future to write the pMAC registers only on the
ENETC ports where a pMAC actually exists.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The build system is complaining about the following:
enetc.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_cbdr.o is added to multiple modules: fsl-enetc fsl-enetc-vf
enetc_ethtool.o is added to multiple modules: fsl-enetc fsl-enetc-vf
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/ipa/ipa_interrupt.c
drivers/net/ipa/ipa_interrupt.h
9ec9b2a30853 ("net: ipa: disable ipa interrupt during suspend")
8e461e1f092b ("net: ipa: introduce ipa_interrupt_enable()")
d50ed3558719 ("net: ipa: enable IPA interrupt handlers separate from registration")
https://lore.kernel.org/all/20230119114125.5182c7ab@canb.auug.org.au/
https://lore.kernel.org/all/79e46152-8043-a512-79d9-c3b905462774@tessares.net/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
napi_synchronize() from enetc_stop() waits until the softirq has
finished execution and no longer wants to be rescheduled. However under
high traffic load, this will never happen, and the interface can never
be closed.
The problem is the fact that the NAPI poll routine is written to update
the consumer index which makes the device want to put more buffers in
the RX ring, which restarts the madness again.
Browsing around, it seems that some drivers like i40e keep a bit
(__I40E_VSI_DOWN) which they use as communication between the control
path and the data path. But that isn't my first choice, because
complications ensue - since the enetc hardirq may trigger while we are
in a theoretical ENETC_DOWN state, it may happen that enetc_msix() masks
it, but enetc_poll() never unmasks it. To prevent a stall in that case,
one would need to schedule all NAPI instances when ENETC_DOWN gets
cleared, to process what's pending.
I find it more desirable for the control path - enetc_stop() - to just
quiesce the RX ring and let the softirq finish what remains there,
without any explicit communication, just by making hardware not provide
any more packets.
This seems possible with the Enable bit of the RX BD ring (RBaMR[EN]).
I can't seem to find an exact definition of what this bit does, but when
the RX ring is disabled, the port seems to no longer update the producer
index, and not react to software updates of the consumer index.
In fact, the RBaMR[EN] bit is already toggled by the driver, but too
late for what we want:
enetc_close()
-> enetc_stop()
-> napi_synchronize()
-> enetc_clear_bdrs()
-> enetc_clear_rxbdr()
The enetc_clear_bdrs() function contains not only logic to disable the
RX and TX rings, but also logic to wait for the TX ring stop being busy.
We split enetc_clear_bdrs() into enetc_disable_bdrs() and
enetc_wait_bdrs(). One needs to run before napi_synchronize() and the
other after (NAPI also processes TX completions, so we maximize our
chances of not waiting for the ENETC_TBSR_BUSY bit - unless a packet is
stuck for some reason, ofc).
We also split off enetc_enable_bdrs() from enetc_setup_bdrs(), and call
this from the mirror position in enetc_start() compared to enetc_stop(),
i.e. right before netif_tx_start_all_queues().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Offloading a BPF program to the RX path of the driver suffers from the
same problems as the PTP reconfiguration - improper error checking can
leave the driver in an invalid state, and the link on the PHY is lost.
Reuse the enetc_reconfigure() procedure, but here, we need to run some
code in the middle of the ring reconfiguration procedure - while the
interface is still down. Introduce a callback which makes that possible.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Follow the convention from this driver, which is to name "struct
net_device *" as "ndev", and the convention from other drivers, to name
"struct netdev_bpf *" as "bpf".
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The crude enetc_stop() -> enetc_open() mechanism suffers from 2
problems:
1. improper error checking
2. it involves phylink_stop() -> phylink_start() which loses the link
Right now, the driver is prepared to offer a better alternative: a ring
reconfiguration procedure which takes the RX BD size (normal or
extended) as argument. It allocates new resources (failing if that
fails), stops the traffic, and assigns the new resources to the rings.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We want to introduce a fast interface reconfiguration procedure, which
involves temporarily stopping the rings.
But we want enetc_start() and enetc_stop() to not restart PHY autoneg,
because that can take a few seconds until it completes again.
So we need part of enetc_start() and enetc_stop(), but not all of them.
Move phylink_start() right next to phylink_of_phy_connect(), and
phylink_stop() right next to phylink_disconnect_phy(), both still in
ndo_open() and ndo_stop().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We have a few instances in the enetc driver where the ring resources
(BD ring iomem, software BD ring, software TSO headers, basically
everything except RX buffers) need to be reallocated. For example, when
RX timestamping is enabled, the RX BD format changes to an extended one
(twice as large).
Currently, this is done using a simplistic enetc_close() -> enetc_open()
procedure. But this is quite crude, since it also invokes phylink_stop()
-> phylink_start(), the link is lost, and a few seconds need to pass for
autoneg to complete again.
In fact it's bad also due to the improper (yolo) error checking. In case
we fail to allocate new resources, we've already freed the old ones, so
the interface is more or less stuck.
To avoid that, we need a system where reconfiguration is possible in a
way in which resources are allocated upfront. This means that there will
be a higher memory usage temporarily, but the assignment of resources to
rings can be done when both the old and new resources are still available.
Introduce a struct enetc_bdr_resource which holds the resources for a
ring, be it RX or TX. This structure duplicates a lot of fields from
struct enetc_bdr (and access to the same fields in the ring structure
was left duplicated, to not change cache characteristics in the fast
path).
When enetc_alloc_tx_resources() runs, it returns an array of resource
elements (one per TX ring), in addition to the existing priv->tx_res.
To populate priv->tx_res with that array, one must call
enetc_assign_tx_resources(), and this also frees the old resources.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extended RX buffer descriptors are necessary if they carry RX
timestamps, which will be true when PTP timestamping is enabled.
Right now, the rx_ring->ext_en is set from the function that allocates
ring resources (enetc_alloc_rx_resources() -> enetc_alloc_rxbdr()), and
also used later, in enetc_setup_rxbdr(). It is also used in the
enetc_rxbd() and enetc_rxbd_next() fast path helpers.
We want to decouple resource allocation from BD ring setup, but both
procedures depend on BD size (extended or not). Move the "extended"
boolean to enetc_open() and pass it both to the RX allocation procedure
as well as to the RX ring setup procedure. The latter will set
rx_ring->ext_en from now on.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call path in enetc_close() is:
enetc_close()
-> enetc_free_rxtx_rings()
-> enetc_free_tx_ring()
-> enetc_free_tx_frame()
-> enetc_free_tx_resources()
-> enetc_free_txbdr()
-> enetc_free_tx_frame()
The enetc_free_tx_frame() function is written such that the second call
exits without doing anything, but nonetheless, it is completely
redundant. Delete it. This makes the TX teardown path more similar to
the RX one, where rx_swbd freeing is done in enetc_free_rx_ring(), not
in enetc_free_rxbdr().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The call path in enetc_close() is:
enetc_close()
-> enetc_free_rxtx_rings()
-> enetc_free_rx_ring()
-> tests whether rx_ring->rx_swbd is NULL
-> enetc_free_tx_ring()
-> tests whether tx_ring->tx_swbd is NULL
-> enetc_free_rx_resources()
-> enetc_free_rxbdr()
-> sets rxr->rx_swbd to NULL
-> enetc_free_tx_resources()
-> enetc_free_txbdr()
-> setx txr->tx_swbd to NULL
From the above, it is clear that due to the function ordering, the
checks for NULL are redundant, since the software buffer descriptor
arrays have not yet been set to NULL. Drop these checks.
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This is a refactoring change which introduces the opposite function of
enetc_dma_alloc_bdr().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
There is only one place which needs to set up indices in the RX ring.
Be consistent with what was done in the TX path and do this in
enetc_setup_rxbdr().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
enetc_alloc_txbdr() deals with allocating resources necessary for a TX
ring to work (the array of software BDs and the array of TSO headers).
The next_to_clean and next_to_use pointers are overwritten with proper
values which are read from hardware here:
enetc_open
-> enetc_alloc_tx_resources
-> enetc_alloc_txbdr
-> set to zero
-> enetc_setup_bdrs
-> enetc_setup_txbdr
-> read from hardware
So their initialization with zeroes is pointless and confusing.
Delete it.
Consequently, since enetc_setup_txbdr() has no opposite cleanup
function, also delete the resetting of these indices from
enetc_free_tx_ring().
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The enetc MDIO bus driver can perform both C22 and C45 transfers.
Create separate functions for each and register the C45 versions using
the new API calls where appropriate.
This driver is shared with the Felix DSA switch, so update that at the
same time.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This lockdep splat says it better than I could:
================================
WARNING: inconsistent lock state
6.2.0-rc2-07010-ga9b9500ffaac-dirty #967 Not tainted
--------------------------------
inconsistent {IN-SOFTIRQ-W} -> {SOFTIRQ-ON-W} usage.
kworker/1:3/179 [HC0[0]:SC0[0]:HE1:SE1] takes:
ffff3ec4036ce098 (_xmit_ETHER#2){+.?.}-{3:3}, at: netif_freeze_queues+0x5c/0xc0
{IN-SOFTIRQ-W} state was registered at:
_raw_spin_lock+0x5c/0xc0
sch_direct_xmit+0x148/0x37c
__dev_queue_xmit+0x528/0x111c
ip6_finish_output2+0x5ec/0xb7c
ip6_finish_output+0x240/0x3f0
ip6_output+0x78/0x360
ndisc_send_skb+0x33c/0x85c
ndisc_send_rs+0x54/0x12c
addrconf_rs_timer+0x154/0x260
call_timer_fn+0xb8/0x3a0
__run_timers.part.0+0x214/0x26c
run_timer_softirq+0x3c/0x74
__do_softirq+0x14c/0x5d8
____do_softirq+0x10/0x20
call_on_irq_stack+0x2c/0x5c
do_softirq_own_stack+0x1c/0x30
__irq_exit_rcu+0x168/0x1a0
irq_exit_rcu+0x10/0x40
el1_interrupt+0x38/0x64
irq event stamp: 7825
hardirqs last enabled at (7825): [<ffffdf1f7200cae4>] exit_to_kernel_mode+0x34/0x130
hardirqs last disabled at (7823): [<ffffdf1f708105f0>] __do_softirq+0x550/0x5d8
softirqs last enabled at (7824): [<ffffdf1f7081050c>] __do_softirq+0x46c/0x5d8
softirqs last disabled at (7811): [<ffffdf1f708166e0>] ____do_softirq+0x10/0x20
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock(_xmit_ETHER#2);
<Interrupt>
lock(_xmit_ETHER#2);
*** DEADLOCK ***
3 locks held by kworker/1:3/179:
#0: ffff3ec400004748 ((wq_completion)events){+.+.}-{0:0}, at: process_one_work+0x1f4/0x6c0
#1: ffff80000a0bbdc8 ((work_completion)(&priv->tx_onestep_tstamp)){+.+.}-{0:0}, at: process_one_work+0x1f4/0x6c0
#2: ffff3ec4036cd438 (&dev->tx_global_lock){+.+.}-{3:3}, at: netif_tx_lock+0x1c/0x34
Workqueue: events enetc_tx_onestep_tstamp
Call trace:
print_usage_bug.part.0+0x208/0x22c
mark_lock+0x7f0/0x8b0
__lock_acquire+0x7c4/0x1ce0
lock_acquire.part.0+0xe0/0x220
lock_acquire+0x68/0x84
_raw_spin_lock+0x5c/0xc0
netif_freeze_queues+0x5c/0xc0
netif_tx_lock+0x24/0x34
enetc_tx_onestep_tstamp+0x20/0x100
process_one_work+0x28c/0x6c0
worker_thread+0x74/0x450
kthread+0x118/0x11c
but I'll say it anyway: the enetc_tx_onestep_tstamp() work item runs in
process context, therefore with softirqs enabled (i.o.w., it can be
interrupted by a softirq). If we hold the netif_tx_lock() when there is
an interrupt, and the NET_TX softirq then gets scheduled, this will take
the netif_tx_lock() a second time and deadlock the kernel.
To solve this, use netif_tx_lock_bh(), which blocks softirqs from
running.
Fixes: 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Link: https://lore.kernel.org/r/20230112105440.1786799-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
While reviewing dependencies in some Kconfig files, I noticed the redundant
dependency "depends on PCI && PCI_MSI". The config PCI_MSI has always,
since its introduction, been dependent on the config PCI. So, it is
sufficient to just depend on PCI_MSI, and know that the dependency on PCI
is implicitly implied.
Reduce the dependencies of some network driver configs.
No functional change and effective change of Kconfig dependendencies.
Signed-off-by: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Acked-by: Simon Horman <simon.horman@corigine.com>
Acked-by: Dimitris Michailidis <dmichail@fungible.com>
Link: https://lore.kernel.org/r/20230111125855.19020-1-lukas.bulwahn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move XDP skb_shared_info structure initialization in from
enetc_map_rx_buff_to_xdp() to enetc_add_rx_buff_to_xdp() and do not always
access skb_shared_info in the xdp_buff/xdp_frame since it is located in a
different cacheline with respect to hard_start and data xdp pointers.
Rely on XDP_FLAGS_HAS_FRAGS flag to check if it really necessary to access
non-linear part of the xdp_buff/xdp_frame.
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Remove xdp_redirect_sg counter and the related ethtool entry since it is
no longer used.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Even if full XDP_REDIRECT is not supported yet for non-linear XDP buffers
since we allow redirecting just into CPUMAPs, unlock XDP_REDIRECT for
S/G XDP buffer and rely on XDP stack to properly take care of the
frames.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Lorenzo Bianconi <lorenzo@kernel.org>
Reviewed-by: Leon Romanovsky <leonro@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A remove callback just returning 0 is equivalent to no remove callback
at all. So drop the useless function.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Before enetc_clean_rx_ring_xdp() calls xdp_do_redirect(), each software
BD in the RX ring between index orig_i and i can have one of 2 refcount
values on its page.
We are the owner of the current buffer that is being processed, so the
refcount will be at least 1.
If the current owner of the buffer at the diametrically opposed index
in the RX ring (i.o.w, the other half of this page) has not yet called
kfree(), this page's refcount could even be 2.
enetc_page_reusable() in enetc_flip_rx_buff() tests for the page
refcount against 1, and [ if it's 2 ] does not attempt to reuse it.
But if enetc_flip_rx_buff() is put after the xdp_do_redirect() call,
the page refcount can have one of 3 values. It can also be 0, if there
is no owner of the other page half, and xdp_do_redirect() for this
buffer ran so far that it triggered a flush of the devmap/cpumap bulk
queue, and the consumers of those bulk queues also freed the buffer,
all by the time xdp_do_redirect() returns the execution back to enetc.
This is the reason why enetc_flip_rx_buff() is called before
xdp_do_redirect(), but there is a big flaw with that reasoning:
enetc_flip_rx_buff() will set rx_swbd->page = NULL on both sides of the
enetc_page_reusable() branch, and if xdp_do_redirect() returns an error,
we call enetc_xdp_free(), which does not deal gracefully with that.
In fact, what happens is quite special. The page refcounts start as 1.
enetc_flip_rx_buff() figures they're reusable, transfers these
rx_swbd->page pointers to a different rx_swbd in enetc_reuse_page(), and
bumps the refcount to 2. When xdp_do_redirect() later returns an error,
we call the no-op enetc_xdp_free(), but we still haven't lost the
reference to that page. A copy of it is still at rx_ring->next_to_alloc,
but that has refcount 2 (and there are no concurrent owners of it in
flight, to drop the refcount). What really kills the system is when
we'll flip the rx_swbd->page the second time around. With an updated
refcount of 2, the page will not be reusable and we'll really leak it.
Then enetc_new_page() will have to allocate more pages, which will then
eventually leak again on further errors from xdp_do_redirect().
The problem, summarized, is that we zeroize rx_swbd->page before we're
completely done with it, and this makes it impossible for the error path
to do something with it.
Since the packet is potentially multi-buffer and therefore the
rx_swbd->page is potentially an array, manual passing of the old
pointers between enetc_flip_rx_buff() and enetc_xdp_free() is a bit
difficult.
For the sake of going with a simple solution, we accept the possibility
of racing with xdp_do_redirect(), and we move the flip procedure to
execute only on the redirect success path. By racing, I mean that the
page may be deemed as not reusable by enetc (having a refcount of 0),
but there will be no leak in that case, either.
Once we accept that, we have something better to do with buffers on
XDP_REDIRECT failure. Since we haven't performed half-page flipping yet,
we won't, either (and this way, we can avoid enetc_xdp_free()
completely, which gives the entire page to the slab allocator).
Instead, we'll call enetc_xdp_drop(), which will recycle this half of
the buffer back to the RX ring.
Fixes: 9d2b68cc108d ("net: enetc: add support for XDP_REDIRECT")
Suggested-by: Lorenzo Bianconi <lorenzo.bianconi@redhat.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/20221213001908.2347046-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
tools/lib/bpf/ringbuf.c
927cbb478adf ("libbpf: Handle size overflow for ringbuf mmap")
b486d19a0ab0 ("libbpf: checkpatch: Fixed code alignments in ringbuf.c")
https://lore.kernel.org/all/20221121122707.44d1446a@canb.auug.org.au/
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the blamed commit, a rudimentary reallocation procedure for RX buffer
descriptors was implemented, for the situation when their format changes
between normal (no PTP) and extended (PTP).
enetc_hwtstamp_set() calls enetc_close() and enetc_open() in a sequence,
and this sequence loses information which was previously configured in
the TX BDR Mode Register, specifically via the enetc_set_bdr_prio() call.
The TX ring priority is configured by tc-mqprio and tc-taprio, and
affects important things for TSN such as the TX time of packets. The
issue manifests itself most visibly by the fact that isochron --txtime
reports premature packet transmissions when PTP is first enabled on an
enetc interface.
Save the TX ring priority in a new field in struct enetc_bdr (occupies a
2 byte hole on arm64) in order to make this survive a ring reconfiguration.
Fixes: 434cebabd3a2 ("enetc: Add dynamic allocation of extended Rx BD rings")
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Reviewed-by: Alexander Lobakin <alexandr.lobakin@intel.com>
Link: https://lore.kernel.org/r/20221122130936.1704151-1-vladimir.oltean@nxp.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Virtually all conventional network drivers are now converted to use
phylink_generic_validate() - only DSA drivers and fman_memac remain,
so lets remove the necessity for network drivers to explicitly set
this member, and default to phylink_generic_validate() when unset.
This is possible as .validate must currently be set.
Any remaining instances that have not been addressed by this patch can
be fixed up later.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Link: https://lore.kernel.org/r/E1or0FZ-001tRa-DI@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
