summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/freescale/enetc
AgeCommit message (Collapse)Author
2022-10-27net: enetc: survive memory pressure without crashingVladimir Oltean
Under memory pressure, enetc_refill_rx_ring() may fail, and when called during the enetc_open() -> enetc_setup_rxbdr() procedure, this is not checked for. An extreme case of memory pressure will result in exactly zero buffers being allocated for the RX ring, and in such a case it is expected that hardware drops all RX packets due to lack of buffers. This does not happen, because the reset-default value of the consumer and produces index is 0, and this makes the ENETC think that all buffers have been initialized and that it owns them (when in reality none were). The hardware guide explains this best: | Configure the receive ring producer index register RBaPIR with a value | of 0. The producer index is initially configured by software but owned | by hardware after the ring has been enabled. Hardware increments the | index when a frame is received which may consume one or more BDs. | Hardware is not allowed to increment the producer index to match the | consumer index since it is used to indicate an empty condition. The ring | can hold at most RBLENR[LENGTH]-1 received BDs. | | Configure the receive ring consumer index register RBaCIR. The | consumer index is owned by software and updated during operation of the | of the BD ring by software, to indicate that any receive data occupied | in the BD has been processed and it has been prepared for new data. | - If consumer index and producer index are initialized to the same | value, it indicates that all BDs in the ring have been prepared and | hardware owns all of the entries. | - If consumer index is initialized to producer index plus N, it would | indicate N BDs have been prepared. Note that hardware cannot start if | only a single buffer is prepared due to the restrictions described in | (2). | - Software may write consumer index to match producer index anytime | while the ring is operational to indicate all received BDs prior have | been processed and new BDs prepared for hardware. Normally, the value of rx_ring->rcir (consumer index) is brought in sync with the rx_ring->next_to_use software index, but this only happens if page allocation ever succeeded. When PI==CI==0, the hardware appears to receive frames and write them to DMA address 0x0 (?!), then set the READY bit in the BD. The enetc_clean_rx_ring() function (and its XDP derivative) is naturally not prepared to handle such a condition. It will attempt to process those frames using the rx_swbd structure associated with index i of the RX ring, but that structure is not fully initialized (enetc_new_page() does all of that). So what happens next is undefined behavior. To operate using no buffer, we must initialize the CI to PI + 1, which will block the hardware from advancing the CI any further, and drop everything. The issue was seen while adding support for zero-copy AF_XDP sockets, where buffer memory comes from user space, which can even decide to supply no buffers at all (example: "xdpsock --txonly"). However, the bug is present also with the network stack code, even though it would take a very determined person to trigger a page allocation failure at the perfect time (a series of ifup/ifdown under memory pressure should eventually reproduce it given enough retries). Fixes: d4fd0404c1c9 ("enetc: Introduce basic PF and VF ENETC ethernet drivers") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20221027182925.3256653-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-10-07net: enetc: Remove duplicated include in enetc_qos.cYang Li
net/pkt_sched.h is included twice in enetc_qos.c, remove one of them. Link: https://bugzilla.openanolis.cn/show_bug.cgi?id=2334 Reported-by: Abaci Robot <abaci@linux.alibaba.com> Signed-off-by: Yang Li <yang.lee@linux.alibaba.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-09-29net: enetc: offload per-tc max SDU from tc-taprioVladimir Oltean
The driver currently sets the PTCMSDUR register statically to the max MTU supported by the interface. Keep this logic if tc-taprio is absent or if the max_sdu for a traffic class is 0, and follow the requested max SDU size otherwise. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-29net: enetc: use common naming scheme for PTGCR and PTGCAPR registersVladimir Oltean
The Port Time Gating Control Register (PTGCR) and Port Time Gating Capability Register (PTGCAPR) have definitions in the driver which aren't in line with the other registers. Rename these. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-29net: enetc: cache accesses to &priv->si->hwVladimir Oltean
The &priv->si->hw construct dereferences 2 pointers and makes lines longer than they need to be, in turn making the code harder to read. Replace &priv->si->hw accesses with a "hw" variable when there are 2 or more accesses within a function that dereference this. This includes loops, since &priv->si->hw is a loop invariant. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-28net: drop the weight argument from netif_napi_addJakub Kicinski
We tell driver developers to always pass NAPI_POLL_WEIGHT as the weight to netif_napi_add(). This may be confusing to newcomers, drop the weight argument, those who really need to tweak the weight can use netif_napi_add_weight(). Acked-by: Marc Kleine-Budde <mkl@pengutronix.de> # for CAN Link: https://lore.kernel.org/r/20220927132753.750069-1-kuba@kernel.org Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
drivers/net/ethernet/freescale/fec.h 7b15515fc1ca ("Revert "fec: Restart PPS after link state change"") 40c79ce13b03 ("net: fec: add stop mode support for imx8 platform") https://lore.kernel.org/all/20220921105337.62b41047@canb.auug.org.au/ drivers/pinctrl/pinctrl-ocelot.c c297561bc98a ("pinctrl: ocelot: Fix interrupt controller") 181f604b33cd ("pinctrl: ocelot: add ability to be used in a non-mmio configuration") https://lore.kernel.org/all/20220921110032.7cd28114@canb.auug.org.au/ tools/testing/selftests/drivers/net/bonding/Makefile bbb774d921e2 ("net: Add tests for bonding and team address list management") 152e8ec77640 ("selftests/bonding: add a test for bonding lladdr target") https://lore.kernel.org/all/20220921110437.5b7dbd82@canb.auug.org.au/ drivers/net/can/usb/gs_usb.c 5440428b3da6 ("can: gs_usb: gs_can_open(): fix race dev->can.state condition") 45dfa45f52e6 ("can: gs_usb: add RX and TX hardware timestamp support") https://lore.kernel.org/all/84f45a7d-92b6-4dc5-d7a1-072152fab6ff@tessares.net/ Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-20net: enetc: deny offload of tc-based TSN features on VF interfacesVladimir Oltean
TSN features on the ENETC (taprio, cbs, gate, police) are configured through a mix of command BD ring messages and port registers: enetc_port_rd(), enetc_port_wr(). Port registers are a region of the ENETC memory map which are only accessible from the PCIe Physical Function. They are not accessible from the Virtual Functions. Moreover, attempting to access these registers crashes the kernel: $ echo 1 > /sys/bus/pci/devices/0000\:00\:00.0/sriov_numvfs pci 0000:00:01.0: [1957:ef00] type 00 class 0x020001 fsl_enetc_vf 0000:00:01.0: Adding to iommu group 15 fsl_enetc_vf 0000:00:01.0: enabling device (0000 -> 0002) fsl_enetc_vf 0000:00:01.0 eno0vf0: renamed from eth0 $ tc qdisc replace dev eno0vf0 root taprio num_tc 8 map 0 1 2 3 4 5 6 7 \ queues 1@0 1@1 1@2 1@3 1@4 1@5 1@6 1@7 base-time 0 \ sched-entry S 0x7f 900000 sched-entry S 0x80 100000 flags 0x2 Unable to handle kernel paging request at virtual address ffff800009551a08 Internal error: Oops: 96000007 [#1] PREEMPT SMP pc : enetc_setup_tc_taprio+0x170/0x47c lr : enetc_setup_tc_taprio+0x16c/0x47c Call trace: enetc_setup_tc_taprio+0x170/0x47c enetc_setup_tc+0x38/0x2dc taprio_change+0x43c/0x970 taprio_init+0x188/0x1e0 qdisc_create+0x114/0x470 tc_modify_qdisc+0x1fc/0x6c0 rtnetlink_rcv_msg+0x12c/0x390 Split enetc_setup_tc() into separate functions for the PF and for the VF drivers. Also remove enetc_qos.o from being included into enetc-vf.ko, since it serves absolutely no purpose there. Fixes: 34c6adf1977b ("enetc: Configure the Time-Aware Scheduler via tc-taprio offload") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220916133209.3351399-2-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-20net: enetc: move enetc_set_psfp() out of the common enetc_set_features()Vladimir Oltean
The VF netdev driver shouldn't respond to changes in the NETIF_F_HW_TC flag; only PFs should. Moreover, TSN-specific code should go to enetc_qos.c, which should not be included in the VF driver. Fixes: 79e499829f3f ("net: enetc: add hw tc hw offload features for PSPF capability") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220916133209.3351399-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-19net: enetc: expose some standardized ethtool countersVladimir Oltean
Structure the code in such a way that it can be reused later for the pMAC statistics, by just changing the "mac" argument to 1. Usage: ethtool --include-statistics --show-pause eno2 ethtool -S eno0 --groups eth-mac ethtool -S eno0 --groups eth-ctrl ethtool -S eno0 --groups rmon Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-09-19net: enetc: parameterize port MAC stats to also cover the pMACVladimir Oltean
The ENETC has counters for the eMAC and for the pMAC exactly 0x1000 apart from each other. The driver only contains definitions for PM0, the eMAC. Rather than duplicating everything for PM1, modify the register definitions such that they take the MAC as argument. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-08-31net: ethernet: move from strlcpy with unused retval to strscpyWolfram Sang
Follow the advice of the below link and prefer 'strscpy' in this subsystem. Conversion is 1:1 because the return value is not used. Generated by a coccinelle script. Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/ Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2 Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5} Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-28net: enetc: Use pci_release_region() to release some resourcesChristophe JAILLET
Some resources are allocated using pci_request_region(). It is more straightforward to release them with pci_release_region(). Fixes: 231ece36f50d ("enetc: Add mdio bus driver for the PCIe MDIO endpoint") Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-05-12net: enetc: kill PHY-less mode for PFsVladimir Oltean
Right now, a PHY-less port (no phy-mode, no fixed-link, no phy-handle) doesn't register with phylink, but calls netif_carrier_on() from enetc_start(). This makes sense for a VF, but for a PF, this is braindead, because we never call enetc_mac_enable() so the MAC is left inoperational. Furthermore, commit 71b77a7a27a3 ("enetc: Migrate to PHYLINK and PCS_LYNX") put the nail in the coffin because it removed the initial netif_carrier_off() call done right after register_netdev(). Without that call, netif_carrier_on() does not call linkwatch_fire_event(), so the operstate remains IF_OPER_UNKNOWN. Just deny the broken configuration by requiring that a phy-mode is present, and always register a PF with phylink. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220511094200.558502-1-vladimir.oltean@nxp.com Signed-off-by: Paolo Abeni <pabeni@redhat.com>
2022-05-11net: enetc: count the tc-taprio window dropsPo Liu
The enetc scheduler for IEEE 802.1Qbv has 2 options (depending on PTGCR[TG_DROP_DISABLE]) when we attempt to send an oversized packet which will never fit in its allotted time slot for its traffic class: either block the entire port due to head-of-line blocking, or drop the packet and set a bit in the writeback format of the transmit buffer descriptor, allowing other packets to be sent. We obviously choose the second option in the driver, but we do not detect the drop condition, so from the perspective of the network stack, the packet is sent and no error counter is incremented. This change checks the writeback of the TX BD when tc-taprio is enabled, and increments a specific ethtool statistics counter and a generic "tx_dropped" counter in ndo_get_stats64. Signed-off-by: Po Liu <Po.Liu@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-05-11net: enetc: manage ENETC_F_QBV in priv->active_offloads only when enabledVladimir Oltean
Future work in this driver would like to look at priv->active_offloads & ENETC_F_QBV to determine whether a tc-taprio qdisc offload was installed, but this does not produce the intended effect. All the other flags in priv->active_offloads are managed dynamically, except ENETC_F_QBV which is set statically based on the probed SI capability. This change makes priv->active_offloads & ENETC_F_QBV really track the presence of a tc-taprio schedule on the port. Some existing users, like the enetc_sched_speed_set() call from phylink_mac_link_up(), are best kept using the old logic: the tc-taprio offload does not re-trigger another link mode resolve, so the scheduler needs to be functional from the get go, as long as Qbv is supported at all on the port. So to preserve functionality there, look at the static station interface capability from pf->si->hw_features instead. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-04-28net: enetc: allow tc-etf offload even with NETIF_F_CSUM_MASKVladimir Oltean
The Time-Specified Departure feature is indeed mutually exclusive with TX IP checksumming in ENETC, but TX checksumming in itself is broken and was removed from this driver in commit 82728b91f124 ("enetc: Remove Tx checksumming offload code"). The blamed commit declared NETIF_F_HW_CSUM in dev->features to comply with software TSO's expectations, and still did the checksumming in software by calling skb_checksum_help(). So there isn't any restriction for the Time-Specified Departure feature. However, enetc_setup_tc_txtime() doesn't understand that, and blindly looks for NETIF_F_CSUM_MASK. Instead of checking for things which can literally never happen in the current code base, just remove the check and let the driver offload tc-etf qdiscs. Fixes: acede3c5dad5 ("net: enetc: declare NETIF_F_HW_CSUM and do it in software") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20220427203017.1291634-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-25net: enetc: report software timestamping via SO_TIMESTAMPINGVladimir Oltean
Let user space properly determine that the enetc driver provides software timestamps. Fixes: 4caefbce06d1 ("enetc: add software timestamping") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220324161210.4122281-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-03-24Merge tag 'net-next-5.18' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next Pull networking updates from Jakub Kicinski: "The sprinkling of SPI drivers is because we added a new one and Mark sent us a SPI driver interface conversion pull request. Core ---- - Introduce XDP multi-buffer support, allowing the use of XDP with jumbo frame MTUs and combination with Rx coalescing offloads (LRO). - Speed up netns dismantling (5x) and lower the memory cost a little. Remove unnecessary per-netns sockets. Scope some lists to a netns. Cut down RCU syncing. Use batch methods. Allow netdev registration to complete out of order. - Support distinguishing timestamp types (ingress vs egress) and maintaining them across packet scrubbing points (e.g. redirect). - Continue the work of annotating packet drop reasons throughout the stack. - Switch netdev error counters from an atomic to dynamically allocated per-CPU counters. - Rework a few preempt_disable(), local_irq_save() and busy waiting sections problematic on PREEMPT_RT. - Extend the ref_tracker to allow catching use-after-free bugs. BPF --- - Introduce "packing allocator" for BPF JIT images. JITed code is marked read only, and used to be allocated at page granularity. Custom allocator allows for more efficient memory use, lower iTLB pressure and prevents identity mapping huge pages from getting split. - Make use of BTF type annotations (e.g. __user, __percpu) to enforce the correct probe read access method, add appropriate helpers. - Convert the BPF preload to use light skeleton and drop the user-mode-driver dependency. - Allow XDP BPF_PROG_RUN test infra to send real packets, enabling its use as a packet generator. - Allow local storage memory to be allocated with GFP_KERNEL if called from a hook allowed to sleep. - Introduce fprobe (multi kprobe) to speed up mass attachment (arch bits to come later). - Add unstable conntrack lookup helpers for BPF by using the BPF kfunc infra. - Allow cgroup BPF progs to return custom errors to user space. - Add support for AF_UNIX iterator batching. - Allow iterator programs to use sleepable helpers. - Support JIT of add, and, or, xor and xchg atomic ops on arm64. - Add BTFGen support to bpftool which allows to use CO-RE in kernels without BTF info. - Large number of libbpf API improvements, cleanups and deprecations. Protocols --------- - Micro-optimize UDPv6 Tx, gaining up to 5% in test on dummy netdev. - Adjust TSO packet sizes based on min_rtt, allowing very low latency links (data centers) to always send full-sized TSO super-frames. - Make IPv6 flow label changes (AKA hash rethink) more configurable, via sysctl and setsockopt. Distinguish between server and client behavior. - VxLAN support to "collect metadata" devices to terminate only configured VNIs. This is similar to VLAN filtering in the bridge. - Support inserting IPv6 IOAM information to a fraction of frames. - Add protocol attribute to IP addresses to allow identifying where given address comes from (kernel-generated, DHCP etc.) - Support setting socket and IPv6 options via cmsg on ping6 sockets. - Reject mis-use of ECN bits in IP headers as part of DSCP/TOS. Define dscp_t and stop taking ECN bits into account in fib-rules. - Add support for locked bridge ports (for 802.1X). - tun: support NAPI for packets received from batched XDP buffs, doubling the performance in some scenarios. - IPv6 extension header handling in Open vSwitch. - Support IPv6 control message load balancing in bonding, prevent neighbor solicitation and advertisement from using the wrong port. Support NS/NA monitor selection similar to existing ARP monitor. - SMC - improve performance with TCP_CORK and sendfile() - support auto-corking - support TCP_NODELAY - MCTP (Management Component Transport Protocol) - add user space tag control interface - I2C binding driver (as specified by DMTF DSP0237) - Multi-BSSID beacon handling in AP mode for WiFi. - Bluetooth: - handle MSFT Monitor Device Event - add MGMT Adv Monitor Device Found/Lost events - Multi-Path TCP: - add support for the SO_SNDTIMEO socket option - lots of selftest cleanups and improvements - Increase the max PDU size in CAN ISOTP to 64 kB. Driver API ---------- - Add HW counters for SW netdevs, a mechanism for devices which offload packet forwarding to report packet statistics back to software interfaces such as tunnels. - Select the default NIC queue count as a fraction of number of physical CPU cores, instead of hard-coding to 8. - Expose devlink instance locks to drivers. Allow device layer of drivers to use that lock directly instead of creating their own which always runs into ordering issues in devlink callbacks. - Add header/data split indication to guide user space enabling of TCP zero-copy Rx. - Allow configuring completion queue event size. - Refactor page_pool to enable fragmenting after allocation. - Add allocation and page reuse statistics to page_pool. - Improve Multiple Spanning Trees support in the bridge to allow reuse of topologies across VLANs, saving HW resources in switches. - DSA (Distributed Switch Architecture): - replay and offload of host VLAN entries - offload of static and local FDB entries on LAG interfaces - FDB isolation and unicast filtering New hardware / drivers ---------------------- - Ethernet: - LAN937x T1 PHYs - Davicom DM9051 SPI NIC driver - Realtek RTL8367S, RTL8367RB-VB switch and MDIO - Microchip ksz8563 switches - Netronome NFP3800 SmartNICs - Fungible SmartNICs - MediaTek MT8195 switches - WiFi: - mt76: MediaTek mt7916 - mt76: MediaTek mt7921u USB adapters - brcmfmac: Broadcom BCM43454/6 - Mobile: - iosm: Intel M.2 7360 WWAN card Drivers ------- - Convert many drivers to the new phylink API built for split PCS designs but also simplifying other cases. - Intel Ethernet NICs: - add TTY for GNSS module for E810T device - improve AF_XDP performance - GTP-C and GTP-U filter offload - QinQ VLAN support - Mellanox Ethernet NICs (mlx5): - support xdp->data_meta - multi-buffer XDP - offload tc push_eth and pop_eth actions - Netronome Ethernet NICs (nfp): - flow-independent tc action hardware offload (police / meter) - AF_XDP - Other Ethernet NICs: - at803x: fiber and SFP support - xgmac: mdio: preamble suppression and custom MDC frequencies - r8169: enable ASPM L1.2 if system vendor flags it as safe - macb/gem: ZynqMP SGMII - hns3: add TX push mode - dpaa2-eth: software TSO - lan743x: multi-queue, mdio, SGMII, PTP - axienet: NAPI and GRO support - Mellanox Ethernet switches (mlxsw): - source and dest IP address rewrites - RJ45 ports - Marvell Ethernet switches (prestera): - basic routing offload - multi-chain TC ACL offload - NXP embedded Ethernet switches (ocelot & felix): - PTP over UDP with the ocelot-8021q DSA tagging protocol - basic QoS classification on Felix DSA switch using dcbnl - port mirroring for ocelot switches - Microchip high-speed industrial Ethernet (sparx5): - offloading of bridge port flooding flags - PTP Hardware Clock - Other embedded switches: - lan966x: PTP Hardward Clock - qca8k: mdio read/write operations via crafted Ethernet packets - Qualcomm 802.11ax WiFi (ath11k): - add LDPC FEC type and 802.11ax High Efficiency data in radiotap - enable RX PPDU stats in monitor co-exist mode - Intel WiFi (iwlwifi): - UHB TAS enablement via BIOS - band disablement via BIOS - channel switch offload - 32 Rx AMPDU sessions in newer devices - MediaTek WiFi (mt76): - background radar detection - thermal management improvements on mt7915 - SAR support for more mt76 platforms - MBSSID and 6 GHz band on mt7915 - RealTek WiFi: - rtw89: AP mode - rtw89: 160 MHz channels and 6 GHz band - rtw89: hardware scan - Bluetooth: - mt7921s: wake on Bluetooth, SCO over I2S, wide-band-speed (WBS) - Microchip CAN (mcp251xfd): - multiple RX-FIFOs and runtime configurable RX/TX rings - internal PLL, runtime PM handling simplification - improve chip detection and error handling after wakeup" * tag 'net-next-5.18' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2521 commits) llc: fix netdevice reference leaks in llc_ui_bind() drivers: ethernet: cpsw: fix panic when interrupt coaleceing is set via ethtool ice: don't allow to run ice_send_event_to_aux() in atomic ctx ice: fix 'scheduling while atomic' on aux critical err interrupt net/sched: fix incorrect vlan_push_eth dest field net: bridge: mst: Restrict info size queries to bridge ports net: marvell: prestera: add missing destroy_workqueue() in prestera_module_init() drivers: net: xgene: Fix regression in CRC stripping net: geneve: add missing netlink policy and size for IFLA_GENEVE_INNER_PROTO_INHERIT net: dsa: fix missing host-filtered multicast addresses net/mlx5e: Fix build warning, detected write beyond size of field iwlwifi: mvm: Don't fail if PPAG isn't supported selftests/bpf: Fix kprobe_multi test. Revert "rethook: x86: Add rethook x86 implementation" Revert "arm64: rethook: Add arm64 rethook implementation" Revert "powerpc: Add rethook support" Revert "ARM: rethook: Add rethook arm implementation" netdevice: add missing dm_private kdoc net: bridge: mst: prevent NULL deref in br_mst_info_size() selftests: forwarding: Use same VRF for port and VLAN upper ...
2022-03-17enetc: use correct format charactersBill Wendling
When compiling with -Wformat, clang emits the following warning: drivers/net/ethernet/freescale/enetc/enetc_mdio.c:151:22: warning: format specifies type 'unsigned char' but the argument has type 'int' [-Wformat] phy_id, dev_addr, regnum); ^~~~~~ ./include/linux/dev_printk.h:163:47: note: expanded from macro 'dev_dbg' dev_printk(KERN_DEBUG, dev, dev_fmt(fmt), ##__VA_ARGS__); \ ~~~ ^~~~~~~~~~~ ./include/linux/dev_printk.h:129:34: note: expanded from macro 'dev_printk' _dev_printk(level, dev, fmt, ##__VA_ARGS__); \ ~~~ ^~~~~~~~~~~ The types of these arguments are unconditionally defined, so this patch updates the format character to the correct ones for ints and unsigned ints. Link: https://github.com/ClangBuiltLinux/linux/issues/378 Signed-off-by: Bill Wendling <morbo@google.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20220316213109.2352015-1-morbo@google.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-02-28flow_offload: reject offload for all drivers with invalid police parametersJianbo Liu
As more police parameters are passed to flow_offload, driver can check them to make sure hardware handles packets in the way indicated by tc. The conform-exceed control should be drop/pipe or drop/ok. Besides, for drop/ok, the police should be the last action. As hardware can't configure peakrate/avrate/overhead, offload should not be supported if any of them is configured. Signed-off-by: Jianbo Liu <jianbol@nvidia.com> Reviewed-by: Ido Schimmel <idosch@nvidia.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-17treewide: Replace zero-length arrays with flexible-array membersGustavo A. R. Silva
There is a regular need in the kernel to provide a way to declare having a dynamically sized set of trailing elements in a structure. Kernel code should always use “flexible array members”[1] for these cases. The older style of one-element or zero-length arrays should no longer be used[2]. This code was transformed with the help of Coccinelle: (next-20220214$ spatch --jobs $(getconf _NPROCESSORS_ONLN) --sp-file script.cocci --include-headers --dir . > output.patch) @@ identifier S, member, array; type T1, T2; @@ struct S { ... T1 member; T2 array[ - 0 ]; }; UAPI and wireless changes were intentionally excluded from this patch and will be sent out separately. [1] https://en.wikipedia.org/wiki/Flexible_array_member [2] https://www.kernel.org/doc/html/v5.16/process/deprecated.html#zero-length-and-one-element-arrays Link: https://github.com/KSPP/linux/issues/78 Reviewed-by: Kees Cook <keescook@chromium.org> Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
2022-02-09net:enetc: enetc qos using the CBDR dma alloc functionPo Liu
Now we can use the enetc_cbd_alloc_data_mem() to replace complicated DMA data alloc method and CBDR memory basic seting. Signed-off-by: Po Liu <po.liu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-09net:enetc: command BD ring data memory alloc as one function alonePo Liu
Separate the CBDR data memory alloc standalone. It is convenient for other part loading, for example the ENETC QOS part. Reported-and-suggested-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: Po Liu <po.liu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-02-09net:enetc: allocate CBD ring data memory using DMA coherent methodsPo Liu
To replace the dma_map_single() stream DMA mapping with DMA coherent method dma_alloc_coherent() which is more simple. dma_map_single() found by Tim Gardner not proper. Suggested by Claudiu Manoil and Jakub Kicinski to use dma_alloc_coherent(). Discussion at: https://lore.kernel.org/netdev/AM9PR04MB8397F300DECD3C44D2EBD07796BD9@AM9PR04MB8397.eurprd04.prod.outlook.com/t/ Fixes: 888ae5a3952ba ("net: enetc: add tc flower psfp offload driver") cc: Claudiu Manoil <claudiu.manoil@nxp.com> Reported-by: Tim Gardner <tim.gardner@canonical.com> Signed-off-by: Po Liu <po.liu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-26net: enetc: use .mac_select_pcs() interfaceRussell King (Oracle)
Convert the PCS selection to use mac_select_pcs, which allows the PCS to perform any validation it needs. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-09net: enetc: Remove useless DMA-32 fallback configurationChristophe JAILLET
As stated in [1], dma_set_mask() with a 64-bit mask never fails if dev->dma_mask is non-NULL. So, if it fails, the 32 bits case will also fail for the same reason. Simplify code and remove some dead code accordingly. [1]: https://lkml.org/lkml/2021/6/7/398 Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Link: https://lore.kernel.org/r/dbecd4eb49a9586ee343b5473dda4b84c42112e9.1641742884.git.christophe.jaillet@wanadoo.fr Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2022-01-02net: ethernet: enetc: name change for clarity from pcs to mdio_deviceColin Foster
A simple variable update from "pcs" to "mdio_device" for the mdio device will make things a little cleaner. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2022-01-02net: phy: lynx: refactor Lynx PCS module to use generic phylink_pcsColin Foster
Remove references to lynx_pcs structures so drivers like the Felix DSA can reference alternate PCS drivers. Signed-off-by: Colin Foster <colin.foster@in-advantage.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-31Merge git://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-nextDavid S. Miller
Alexei Starovoitov says: ==================== pull-request: bpf-next 2021-12-30 The following pull-request contains BPF updates for your *net-next* tree. We've added 72 non-merge commits during the last 20 day(s) which contain a total of 223 files changed, 3510 insertions(+), 1591 deletions(-). The main changes are: 1) Automatic setrlimit in libbpf when bpf is memcg's in the kernel, from Andrii. 2) Beautify and de-verbose verifier logs, from Christy. 3) Composable verifier types, from Hao. 4) bpf_strncmp helper, from Hou. 5) bpf.h header dependency cleanup, from Jakub. 6) get_func_[arg|ret|arg_cnt] helpers, from Jiri. 7) Sleepable local storage, from KP. 8) Extend kfunc with PTR_TO_CTX, PTR_TO_MEM argument support, from Kumar. ==================== Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-19flow_offload: add index to flow_action_entry structureBaowen Zheng
Add index to flow_action_entry structure and delete index from police and gate child structure. We make this change to offload tc action for driver to identify a tc action. Signed-off-by: Baowen Zheng <baowen.zheng@corigine.com> Signed-off-by: Simon Horman <simon.horman@corigine.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-12-13bpf: Let bpf_warn_invalid_xdp_action() report more infoPaolo Abeni
In non trivial scenarios, the action id alone is not sufficient to identify the program causing the warning. Before the previous patch, the generated stack-trace pointed out at least the involved device driver. Let's additionally include the program name and id, and the relevant device name. If the user needs additional infos, he can fetch them via a kernel probe, leveraging the arguments added here. Signed-off-by: Paolo Abeni <pabeni@redhat.com> Signed-off-by: Daniel Borkmann <daniel@iogearbox.net> Acked-by: Toke Høiland-Jørgensen <toke@redhat.com> Link: https://lore.kernel.org/bpf/ddb96bb975cbfddb1546cf5da60e77d5100b533c.1638189075.git.pabeni@redhat.com
2021-11-22ethtool: extend ringparam setting/getting API with rx_buf_lenHao Chen
Add two new parameters kernel_ringparam and extack for .get_ringparam and .set_ringparam to extend more ring params through netlink. Signed-off-by: Hao Chen <chenhao288@hisilicon.com> Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: use phylink_generic_validate()Russell King (Oracle)
enetc has no special behaviour in its validation implementation, so can be switched to phylink_generic_validate(). Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: remove interface checks in enetc_pl_mac_validate()Russell King (Oracle)
As phylink checks the interface mode against the supported_interfaces bitmap, we no longer need to validate the interface mode in the validation function. Remove this to simplify it. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-11-17net: enetc: populate supported_interfaces memberRussell King (Oracle)
Populate the phy_interface_t bitmap for the Freescale enetc driver with interfaces modes supported by the MAC. Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-24net: convert users of bitmap_foo() to linkmode_foo()Sean Anderson
This converts instances of bitmap_foo(args..., __ETHTOOL_LINK_MODE_MASK_NBITS) to linkmode_foo(args...) I manually fixed up some lines to prevent them from being excessively long. Otherwise, this change was generated with the following semantic patch: // Generated with // echo linux/linkmode.h > includes // git grep -Flf includes include/ | cut -f 2- -d / | cat includes - \ // | sort | uniq | tee new_includes | wc -l && mv new_includes includes // and repeating until the number stopped going up @i@ @@ ( #include <linux/acpi_mdio.h> | #include <linux/brcmphy.h> | #include <linux/dsa/loop.h> | #include <linux/dsa/sja1105.h> | #include <linux/ethtool.h> | #include <linux/ethtool_netlink.h> | #include <linux/fec.h> | #include <linux/fs_enet_pd.h> | #include <linux/fsl/enetc_mdio.h> | #include <linux/fwnode_mdio.h> | #include <linux/linkmode.h> | #include <linux/lsm_audit.h> | #include <linux/mdio-bitbang.h> | #include <linux/mdio.h> | #include <linux/mdio-mux.h> | #include <linux/mii.h> | #include <linux/mii_timestamper.h> | #include <linux/mlx5/accel.h> | #include <linux/mlx5/cq.h> | #include <linux/mlx5/device.h> | #include <linux/mlx5/driver.h> | #include <linux/mlx5/eswitch.h> | #include <linux/mlx5/fs.h> | #include <linux/mlx5/port.h> | #include <linux/mlx5/qp.h> | #include <linux/mlx5/rsc_dump.h> | #include <linux/mlx5/transobj.h> | #include <linux/mlx5/vport.h> | #include <linux/of_mdio.h> | #include <linux/of_net.h> | #include <linux/pcs-lynx.h> | #include <linux/pcs/pcs-xpcs.h> | #include <linux/phy.h> | #include <linux/phy_led_triggers.h> | #include <linux/phylink.h> | #include <linux/platform_data/bcmgenet.h> | #include <linux/platform_data/xilinx-ll-temac.h> | #include <linux/pxa168_eth.h> | #include <linux/qed/qed_eth_if.h> | #include <linux/qed/qed_fcoe_if.h> | #include <linux/qed/qed_if.h> | #include <linux/qed/qed_iov_if.h> | #include <linux/qed/qed_iscsi_if.h> | #include <linux/qed/qed_ll2_if.h> | #include <linux/qed/qed_nvmetcp_if.h> | #include <linux/qed/qed_rdma_if.h> | #include <linux/sfp.h> | #include <linux/sh_eth.h> | #include <linux/smsc911x.h> | #include <linux/soc/nxp/lpc32xx-misc.h> | #include <linux/stmmac.h> | #include <linux/sunrpc/svc_rdma.h> | #include <linux/sxgbe_platform.h> | #include <net/cfg80211.h> | #include <net/dsa.h> | #include <net/mac80211.h> | #include <net/selftests.h> | #include <rdma/ib_addr.h> | #include <rdma/ib_cache.h> | #include <rdma/ib_cm.h> | #include <rdma/ib_hdrs.h> | #include <rdma/ib_mad.h> | #include <rdma/ib_marshall.h> | #include <rdma/ib_pack.h> | #include <rdma/ib_pma.h> | #include <rdma/ib_sa.h> | #include <rdma/ib_smi.h> | #include <rdma/ib_umem.h> | #include <rdma/ib_umem_odp.h> | #include <rdma/ib_verbs.h> | #include <rdma/iw_cm.h> | #include <rdma/mr_pool.h> | #include <rdma/opa_addr.h> | #include <rdma/opa_port_info.h> | #include <rdma/opa_smi.h> | #include <rdma/opa_vnic.h> | #include <rdma/rdma_cm.h> | #include <rdma/rdma_cm_ib.h> | #include <rdma/rdmavt_cq.h> | #include <rdma/rdma_vt.h> | #include <rdma/rdmavt_qp.h> | #include <rdma/rw.h> | #include <rdma/tid_rdma_defs.h> | #include <rdma/uverbs_ioctl.h> | #include <rdma/uverbs_named_ioctl.h> | #include <rdma/uverbs_std_types.h> | #include <rdma/uverbs_types.h> | #include <soc/mscc/ocelot.h> | #include <soc/mscc/ocelot_ptp.h> | #include <soc/mscc/ocelot_vcap.h> | #include <trace/events/ib_mad.h> | #include <trace/events/rdma_core.h> | #include <trace/events/rdma.h> | #include <trace/events/rpcrdma.h> | #include <uapi/linux/ethtool.h> | #include <uapi/linux/ethtool_netlink.h> | #include <uapi/linux/mdio.h> | #include <uapi/linux/mii.h> ) @depends on i@ expression list args; @@ ( - bitmap_zero(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_zero(args) | - bitmap_copy(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_copy(args) | - bitmap_and(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_and(args) | - bitmap_or(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_or(args) | - bitmap_empty(args, ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_empty(args) | - bitmap_andnot(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_andnot(args) | - bitmap_equal(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_equal(args) | - bitmap_intersects(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_intersects(args) | - bitmap_subset(args, __ETHTOOL_LINK_MODE_MASK_NBITS) + linkmode_subset(args) ) Add missing linux/mii.h include to mellanox. -DaveM Signed-off-by: Sean Anderson <sean.anderson@seco.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-22Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netDavid S. Miller
Lots of simnple overlapping additions. With a build fix from Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-21net: enetc: use the skb variable directly in enetc_clean_tx_ring()Vladimir Oltean
The code checks whether the skb had one-step TX timestamping enabled, in order to schedule the work item for emptying the priv->tx_skbs queue. That code checks for "tx_swbd->skb" directly, when we already had a skb retrieved using enetc_tx_swbd_get_skb(tx_swbd) - a TX software BD can also hold an XDP_TX packet or an XDP frame. But since the direct tx_swbd dereference is in an "if" block guarded by the non-NULL quality of "skb", accessing "tx_swbd->skb" directly is not wrong, just confusing. Just use the local variable named "skb". Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-21net: enetc: remove local "priv" variable in enetc_clean_tx_ring()Vladimir Oltean
The "priv" variable is needed in the "check_writeback" scope since commit d39823121911 ("enetc: add hardware timestamping support"). Since commit 7294380c5211 ("enetc: support PTP Sync packet one-step timestamping"), we also need "priv" in the larger function scope. So the local variable from the "if" block scope is not needed, and actually shadows the other one. Delete it. Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-21net: enetc: make sure all traffic classes can send large framesVladimir Oltean
The enetc driver does not implement .ndo_change_mtu, instead it configures the MAC register field PTC{Traffic Class}MSDUR[MAXSDU] statically to a large value during probe time. The driver used to configure only the max SDU for traffic class 0, and that was fine while the driver could only use traffic class 0. But with the introduction of mqprio, sending a large frame into any other TC than 0 is broken. This patch fixes that by replicating per traffic class the static configuration done in enetc_configure_port_mac(). Fixes: cbe9e835946f ("enetc: Enable TC offloading with mqprio") Reported-by: Richie Pearn <richard.pearn@nxp.com> Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20211020173340.1089992-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-21net: enetc: fix ethtool counter name for PM0_TERRVladimir Oltean
There are two counters named "MAC tx frames", one of them is actually incorrect. The correct name for that counter should be "MAC tx error frames", which is symmetric to the existing "MAC rx error frames". Fixes: 16eb4c85c964 ("enetc: Add ethtool statistics") Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com> Reviewed-by: <Claudiu Manoil <claudiu.manoil@nxp.com> Link: https://lore.kernel.org/r/20211020165206.1069889-1-vladimir.oltean@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-20net: enetc: unmap DMA in enetc_send_cmd()Tim Gardner
Coverity complains of a possible dereference of a null return value. 5. returned_null: kzalloc returns NULL. [show details] 6. var_assigned: Assigning: si_data = NULL return value from kzalloc. 488 si_data = kzalloc(data_size, __GFP_DMA | GFP_KERNEL); 489 cbd.length = cpu_to_le16(data_size); 490 491 dma = dma_map_single(&priv->si->pdev->dev, si_data, 492 data_size, DMA_FROM_DEVICE); While this kzalloc() is unlikely to fail, I did notice that the function returned without unmapping si_data. Fix this by refactoring the error paths and checking for kzalloc() failure. Fixes: 888ae5a3952ba ("net: enetc: add tc flower psfp offload driver") Cc: Claudiu Manoil <claudiu.manoil@nxp.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Jakub Kicinski <kuba@kernel.org> Cc: netdev@vger.kernel.org Cc: linux-kernel@vger.kernel.org (open list) Signed-off-by: Tim Gardner <tim.gardner@canonical.com> Acked-by: Claudiu Manoil <claudiu.manoil@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-16ethernet: enetc: use eth_hw_addr_set()Jakub Kicinski
Commit 406f42fa0d3c ("net-next: When a bond have a massive amount of VLANs...") introduced a rbtree for faster Ethernet address look up. To maintain netdev->dev_addr in this tree we need to make all the writes to it got through appropriate helpers. Pass a netdev into the helper instead of just the address, read the address into an array on the stack, then call eth_hw_addr_set(). Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-13net: enetc: fix check for allocation failureDan Carpenter
This was supposed to be a check for if dma_alloc_coherent() failed but it has a copy and paste bug so it will not work. Fixes: fb8629e2cbfc ("net: enetc: add support for software TSO") Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Reviewed-by: Ioana Ciornei <ioana.ciornei@nxp.com> Link: https://lore.kernel.org/r/20211013080456.GC6010@kili Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-13net: enetc: include ip6_checksum.h for csum_ipv6_magicIoana Ciornei
For those architectures which do not define_HAVE_ARCH_IPV6_CSUM, we need to include ip6_checksum.h which provides the csum_ipv6_magic() function. Fixes: fb8629e2cbfc ("net: enetc: add support for software TSO") Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Link: https://lore.kernel.org/r/20211012121358.16641-1-ioana.ciornei@nxp.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-10-08net: enetc: add support for software TSOIoana Ciornei
This patch adds support for driver level TSO in the enetc driver using the TSO API. Beside using the usual tso_build_hdr(), tso_build_data() this specific implementation also has to compute the checksum, both IP and L4, for each resulted segment. This is because the ENETC controller does not support Tx checksum offload which is needed in order to take advantage of TSO. With the workaround for the ENETC MDIO erratum in place the Tx path of the driver is forced to lock/unlock for each skb sent. This is why, even though we are computing the checksum by hand we see the following improvement in TCP termination on the LS1028A SoC, on a single A72 core running at 1.3GHz: before: 1.63 Gbits/sec after: 2.34 Gbits/sec Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Claudiu Manoil <claudiu.manoil@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-08net: enetc: declare NETIF_F_HW_CSUM and do it in softwareIoana Ciornei
This is just a preparation patch for software TSO in the enetc driver. Unfortunately, ENETC does not support Tx checksum offload which would normally render TSO, even software, impossible. Declare NETIF_F_HW_CSUM as part of the feature set and do it at driver level using skb_csum_hwoffload_help() so that we can move forward and also add support for TSO in the next patch. Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Reviewed-by: Vladimir Oltean <vladimir.oltean@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-10-05ethernet: use eth_hw_addr_set() for dev->addr_len casesJakub Kicinski
Convert all Ethernet drivers from memcpy(... dev->addr_len) to eth_hw_addr_set(): @@ expression dev, np; @@ - memcpy(dev->dev_addr, np, dev->addr_len) + eth_hw_addr_set(dev, np) In theory addr_len may not be ETH_ALEN, but we don't expect non-Ethernet devices to live under this directory, and only the following cases of setting addr_len exist: - cxgb4 for mgmt device, and the drivers which set it to ETH_ALEN: s2io, mlx4, vxge. Signed-off-by: Jakub Kicinski <kuba@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2021-09-30Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/netJakub Kicinski
drivers/net/phy/bcm7xxx.c d88fd1b546ff ("net: phy: bcm7xxx: Fixed indirect MMD operations") f68d08c437f9 ("net: phy: bcm7xxx: Add EPHY entry for 72165") net/sched/sch_api.c b193e15ac69d ("net: prevent user from passing illegal stab size") 69508d43334e ("net_sched: Use struct_size() and flex_array_size() helpers") Both cases trivial - adjacent code additions. Signed-off-by: Jakub Kicinski <kuba@kernel.org>