| Age | Commit message (Collapse) | Author |
|---|
|
If we remove modes from EEE advertisement and disable / re-enable EEE,
then advertisement is set to all supported modes. I don't think this is
what the user expects. So respect the cached advertisement and just fall
back to all supported modes if cached advertisement is empty.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c75f7f8b-5571-429f-abd3-ce682d178a4b@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
DP83848 datasheet (section 4.7.2) indicates that the reset pin should be
toggled after the clocks are running. Add the PHY_RST_AFTER_CLK_EN to
make sure that this indication is respected.
In my experience not having this flag enabled would lead to, on some
boots, the wrong MII mode being selected if the PHY was initialized on
the bootloader and was receiving data during Linux boot.
Signed-off-by: Diogo Silva <diogompaissilva@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Fixes: 34e45ad9378c ("net: phy: dp83848: Add TI DP83848 Ethernet PHY")
Link: https://patch.msgid.link/20241102151504.811306-1-paissilva@ld-100007.ds1.internal
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These are the preferred way to copy ethtool strings.
Avoids incrementing pointers all over the place.
Signed-off-by: Rosen Penev <rosenp@gmail.com>
Link: https://patch.msgid.link/20241029234641.11448-1-rosenp@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Like the DP83826, the DP83825 can also be configured as an RMII master or
slave via a control register. The existing function responsible for this
configuration is renamed to a general dp8382x function. The DP83825 only
supports RMII so nothing more needs to be configured.
With this change, the dp83822_driver list is reorganized according to the
device name.
Signed-off-by: Erik Schumacher <erik.schumacher@iris-sensing.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/aa62d081804f44b5af0e8de2372ae6bfe1affd34.camel@iris-sensing.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
There are a few issues with how SFP PHYs are attached:
a) The phylink_sfp_connect_phy() and phylink_sfp_config_phy() code
validates the configuration three times:
1. To discover the support/advertising masks that the PHY/PCS/MAC
can support in order to select an interface.
2. To validate the selected interface.
3. When the PHY is brought up after being attached, another validation
is done.
This is needlessly complex.
b) The configuration is set prior to the PHY being attached, which
means we don't have the PHY available in phylink_major_config()
for phylink_pcs_neg_mode() to make decisions upon.
We have already added an extra step to validate the selected interface,
so we can now move the attachment and bringup of the PHY earlier,
inside phylink_sfp_config_phy(). This results in the validation at
step 2 above becoming entirely unnecessary, so remove that too.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcb-000c8H-3e@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate that the returned interface from sfp_select_interface() is
supportable by the MAC/PCS. If it isn't, print an error and return
the NA interface type. This is a preparatory step to reorganising
how a PHY on a SFP module is handled.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcV-000c8B-Vz@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Whenever we call sfp_select_interface(), we check the returned value
and print an error. There are two cases where this happens with the
same message. Provide a common function to do this.
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Tested-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/E1t3bcQ-000c85-S4@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
phylink_parse_fixedlink() wants to preserve the pause, asym_pause and
autoneg bits in pl->supported. Rather than reading the bits into
separate bools, zeroing pl->supported, and then setting them if they
were previously set, use a mask and linkmode_and() to achieve the same
result.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Simon Horman <horms@kernel.org>
Link: https://patch.msgid.link/E1t3Fh5-000aQi-Nk@rmk-PC.armlinux.org.uk
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR.
No conflicts and no adjacent changes.
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Report MDI-X resolved state after link up.
Tested on Linkstreet 88E6193X internal PHYs.
Signed-off-by: Paul Davey <paul.davey@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241017015026.255224-1-paul.davey@alliedtelesis.co.nz
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Seems Alcatel Lucent G-010S-P also have the same problem that it uses
TX_FAULT pin for SOC uart. So apply sfp_fixup_ignore_tx_fault to it.
Signed-off-by: Shengyu Qu <wiagn233@outlook.com>
Link: https://patch.msgid.link/TYCPR01MB84373677E45A7BFA5A28232C98792@TYCPR01MB8437.jpnprd01.prod.outlook.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The first boards show up with Realtek's RTL8125D. This MAC/PHY chip
comes with an integrated 2.5Gbps PHY with ID 0x001cc841. It's not
clear yet whether there's an external version of this PHY and how
Realtek calls it, therefore use the numeric id for now.
Link: https://lore.kernel.org/netdev/2ada65e1-5dfa-456c-9334-2bc51272e9da@gmail.com/T/
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Message-ID: <7d2924de-053b-44d2-a479-870dc3878170@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
This patch propagates error code correctly in cal_cycle()
and improve with FIELD_GET().
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
This patch shrinks line wrapping to 80 chars. Also, in
tx_amp_fill_result(), use FIELD_PREP() to prettify code.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
This patch fixes spelling errors, re-arrange vars with
reverse Xmas tree and remove unnecessary parens in
mediatek-ge-soc.c.
Signed-off-by: SkyLake.Huang <skylake.huang@mediatek.com>
Reviewed-by: Simon Horman <horms@kernel.org>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
This change fixes a rare issue where the PHY fails to detect a link
due to incorrect reset behavior.
The SW_RESET definition was incorrectly assigned to bit 14, which is the
Digital Restart bit according to the datasheet. This commit corrects
SW_RESET to bit 15 and assigns DIG_RESTART to bit 14 as per the
datasheet specifications.
The SW_RESET define is only used in the phy_reset function, which fully
re-initializes the PHY after the reset is performed. The change in the
bit definitions should not have any negative impact on the functionality
of the PHY.
v2:
- added Fixes tag
- improved commit message
Cc: stable@vger.kernel.org
Fixes: 5dc39fd5ef35 ("net: phy: DP83822: Add ability to advertise Fiber connection")
Signed-off-by: Alex Michel <alex.michel@wiedemann-group.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Message-ID: <AS1P250MB0608A798661549BF83C4B43EA9462@AS1P250MB0608.EURP250.PROD.OUTLOOK.COM>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
With DSA's implementation of the mac_select_pcs() method removed, we
can now remove the detection of mac_select_pcs() implementation.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
When the mac_select_pcs() method is not implemented, there is no way
for pl->pcs to be set to a non-NULL value. This was here to support
the old phylink_set_pcs() method which has been removed a few years
ago. Simplify the code in phylink_validate_mac_and_pcs().
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
phylink has historically not permitted a PCS to be removed. An attempt
to permit this with phylink_set_pcs() resulted in comments indicating
that there was no need for this. This behaviour has been propagated
forward to the mac_select_pcs() approach as it was believed from these
comments that changing this would be NAK'd.
However, with mac_select_pcs(), it takes more code and thus complexity
to maintain this behaviour, which can - and in this case has - resulted
in a bug. If mac_select_pcs() returns NULL for a particular interface
type, but there is already a PCS in-use, then we skip the pcs_validate()
method, but continue using the old PCS. Also, it wouldn't be expected
behaviour by implementers of mac_select_pcs().
Allow this by removing this old unnecessary restriction.
Signed-off-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
|
|
The Realtek RTL8125/RTL8126 NBase-T MAC/PHY chips have internal PHY's
which are register-compatible, at least for the registers we use here.
So let's use just one PHY driver to support all of them.
These internal PHY's exist also as external C45 PHY's, but on the
internal PHY's no access to MMD registers is possible. This can be
used to differentiate between the internal and external version.
As a side effect the drivers for two now external-only drivers don't
require read_mmd/write_mmd hooks any longer.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Link: https://patch.msgid.link/c57081a6-811f-4571-ab35-34f4ca6de9af@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Clear 1000Base-T link partner advertisement bits in Clause-45
read_status() function in case auto-negotiation is disabled or has not
been completed.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/9dc9b47b2d675708afef3ad366bfd78eb584d958.1728565530.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Always call rtlgen_read_status() first, so genphy_read_status() which
is called by it clears bits in case auto-negotiation has not completed.
Also clear 10GBT link-partner advertisement bits in case auto-negotiation
is disabled or has not completed.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/b15929a41621d215c6b2b57393368086589569ec.1728565530.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
The PHYSR MMD register is present and defined equally for all RTL82xx
Ethernet PHYs.
Read duplex and Gbit master bits from rtlgen_decode_speed() and rename
it to rtlgen_decode_physr().
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Link: https://patch.msgid.link/b9a76341da851a18c985bc4774fa295babec79bb.1728565530.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
of_property_read_u32() returns -EINVAL in case the property cannot be
found rather than -ENOENT. Fix the check to not abort probing in case
of the property being missing, and also in case CONFIG_OF is not set
which will result in -ENOSYS.
Fixes: a2e1ba275eae ("net: phy: aquantia: allow forcing order of MDI pairs")
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Closes: https://lore.kernel.org/all/114b4c03-5d16-42ed-945d-cf78eabea12b@nvidia.com/
Suggested-by: Hans-Frieder Vogt <hfdevel@gmx.net>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://patch.msgid.link/f8282e2fc6a5ac91fe91491edc7f1ca8f4a65a0d.1728825323.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The intel-xway PHY driver predates the PHY LED framework and currently
initializes all LED pins to equal default values.
Add PHY LED functions to the drivers and don't set default values if
LEDs are defined in device tree.
According the datasheets 3 LEDs are supported on all Intel XWAY PHYs.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/81f4717ab9acf38f3239727a4540ae96fd01109b.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
According the datasheet covering the LED (0x1b) register:
0B Active High LEDx pin driven high when activated
1B Active Low LEDx pin driven low when activated
Make use of the now available 'active-high' property and correctly
reflect the polarity setting which was previously inverted.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/180ccafa837f09908b852a8a874a3808c5ecd2d0.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Use newly defined 'active-high' property to set the
VEND1_GLOBAL_LED_DRIVE_VDD bit and let 'active-low' clear that bit. This
reflects the technical reality which was inverted in the previous
description in which the 'active-low' property was used to actually set
the VEND1_GLOBAL_LED_DRIVE_VDD bit, which means that VDD (ie. supply
voltage) of the LED is driven rather than GND.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/86a413b4387c42dcb54f587cc2433a06f16aae83.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
In addition to 'active-low' and 'inactive-high-impedance' also
support 'active-high' property for PHY LED pin configuration.
As only either 'active-high' or 'active-low' can be set at the
same time, WARN and return an error in case both are set.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/91598487773d768f254d5faf06cf65b13e972f0e.1728558223.git.daniel@makrotopia.org
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
For TJA11xx PHYs, they have the capability to output 50MHz reference
clock on REF_CLK pin in RMII mode, which is called "revRMII" mode in
the PHY data sheet.
Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
PHYs performing rate-matching using MAC-side flow-control always
perform duplex-matching as well in case they are supporting
half-duplex modes at all.
No longer remove half-duplex modes from their capabilities.
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Link: https://patch.msgid.link/b157c0c289cfba024039a96e635d037f9d946745.1728617993.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
As per LAN8650/1 Rev.B0/B1 AN1760 (Revision F (DS60001760G - June 2024))
and LAN8670/1/2 Rev.C1/C2 AN1699 (Revision E (DS60001699F - June 2024)),
under normal operation, the device should be operated in PLCA mode.
Disabling collision detection is recommended to allow the device to
operate in noisy environments or when reflections and other inherent
transmission line distortion cause poor signal quality. Collision
detection must be re-enabled if the device is configured to operate in
CSMA/CD mode.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-8-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for LAN8670/1/2 Rev.C2 as per the latest configuration note
AN1699 released (Revision E (DS60001699F - June 2024)) for Rev.C1 is also
applicable for Rev.C2. Refer hardware revisions list in the latest AN1699
Revision E (DS60001699F - June 2024).
https://www.microchip.com/en-us/application-notes/an1699
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-7-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for LAN8670/1/2 Rev.C1 as per the latest configuration note
AN1699 released (Revision E (DS60001699F - June 2024)).
https://www.microchip.com/en-us/application-notes/an1699
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-6-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move LAN867X reset handling code to a new function called
lan867x_check_reset_complete() which will be useful for the next patch
which also uses the same code to handle the reset functionality.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-5-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add support for LAN8650/1 Rev.B1. As per the latest configuration note
AN1760 released (Revision F (DS60001760G - June 2024)) for Rev.B0 is also
applicable for Rev.B1. Refer hardware revisions list in the latest AN1760
Revision F (DS60001760G - June 2024).
https://www.microchip.com/en-us/application-notes/an1760
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-4-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the new/improved initial settings from the latest configuration
application note AN1760 released for LAN8650/1 Rev.B0 Revision F
(DS60001760G - June 2024).
https://www.microchip.com/en-us/application-notes/an1760
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-3-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Restructure lan865x_write_cfg_params() and lan865x_read_cfg_params()
functions arguments to more generic which will be useful for the next
patch which updates the improved initial configuration for LAN8650/1
Rev.B0 published in the Configuration Note.
Signed-off-by: Parthiban Veerasooran <parthiban.veerasooran@microchip.com>
Link: https://patch.msgid.link/20241010082205.221493-2-parthiban.veerasooran@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The system interface connection status register is not immediately
correct upon line side link up. This results in the status being read as
OFF and then transitioning to the correct host side link mode with a
short delay. This causes the phylink framework passing the OFF status
down to all MAC config drivers, resulting in the host side link being
misconfigured, which in turn can lead to link flapping or complete
packet loss in some cases.
Mitigate this by periodically polling the register until it not showing
the OFF state. This will be done every 1ms for 10ms, using the same
poll/timeout as the processor intensive operation reads.
If the phy is still expressing the OFF state after the timeout, then set
the link to false and pass the NA interface mode onto the phylink
framework.
Signed-off-by: Aryan Srivastava <aryan.srivastava@alliedtelesis.co.nz>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241010004935.1774601-1-aryan.srivastava@alliedtelesis.co.nz
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Cross-merge networking fixes after downstream PR (net-6.12-rc3).
No conflicts and no adjacent changes.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Validate PHY LED OPs presence before registering and parsing them.
Defining LED nodes for a PHY driver that actually doesn't supports them
is redundant and useless.
It's also the case with Generic PHY driver used and a DT having LEDs
node for the specific PHY.
Skip it and report the error with debug print enabled.
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241008194718.9682-1-ansuelsmth@gmail.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
All MMD reads return 0 for the RTL8126A-integrated PHY. Therefore phylib
assumes it doesn't support EEE, what results in higher power consumption,
and a significantly higher chip temperature in my case.
To fix this split out the PHY driver for the RTL8126A-integrated PHY
and set the read_mmd/write_mmd callbacks to read from vendor-specific
registers.
Fixes: 5befa3728b85 ("net: phy: realtek: add support for RTL8126A-integrated 5Gbps PHY")
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for measuring Signal Quality Index for LAN887x T1 PHY.
Signal Quality Index (SQI) is measure of Link Channel Quality from
0 to 7, with 7 as the best. By default, a link loss event shall
indicate an SQI of 0.
Signed-off-by: Tarun Alle <Tarun.Alle@microchip.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241007063943.3233-1-tarun.alle@microchip.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The initial marvell-88q2xxx driver only supported the Marvell 88Q2110
PHY without auto negotiation support. The reason documented states that
the provided initialization sequence did not to work. Now a method to
enable auto negotiation have been found by comparing the initialization
of other supported devices and an out-of-tree PHY driver.
Perform the minimal needed initialization of the PHY to get auto
negotiation working and remove the limitation that disables the auto
negotiation feature for the mv88q2110 device.
With this change a 1000Mbps full duplex link is able to be negotiated
between two mv88q2110 and the link works perfectly. The other side also
reflects the manually configure settings of the master device.
# ethtool eth0
Settings for eth0:
Supported ports: [ ]
Supported link modes: 100baseT1/Full
1000baseT1/Full
Supported pause frame use: Symmetric Receive-only
Supports auto-negotiation: Yes
Supported FEC modes: Not reported
Advertised link modes: 100baseT1/Full
1000baseT1/Full
Advertised pause frame use: No
Advertised auto-negotiation: Yes
Advertised FEC modes: Not reported
Link partner advertised link modes: 100baseT1/Full
1000baseT1/Full
Link partner advertised pause frame use: No
Link partner advertised auto-negotiation: Yes
Link partner advertised FEC modes: Not reported
Speed: 1000Mb/s
Duplex: Full
Auto-negotiation: on
master-slave cfg: preferred master
master-slave status: slave
Port: Twisted Pair
PHYAD: 0
Transceiver: external
MDI-X: Unknown
Link detected: yes
SQI: 15/15
Before this change I was not able to manually configure 1000Mbps link,
only a 100Mpps link so this change providers an improvement in
performance for this device.
[ 5] local 10.1.0.2 port 5201 connected to 10.1.0.1 port 38346
[ ID] Interval Transfer Bitrate Retr Cwnd
[ 5] 0.00-1.00 sec 96.8 MBytes 812 Mbits/sec 0 469 KBytes
[ 5] 1.00-2.00 sec 94.3 MBytes 791 Mbits/sec 0 469 KBytes
[ 5] 2.00-3.00 sec 96.1 MBytes 806 Mbits/sec 0 469 KBytes
[ 5] 3.00-4.00 sec 98.3 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 4.00-5.00 sec 98.4 MBytes 825 Mbits/sec 0 469 KBytes
[ 5] 5.00-6.00 sec 98.4 MBytes 826 Mbits/sec 0 469 KBytes
[ 5] 6.00-7.00 sec 98.9 MBytes 830 Mbits/sec 0 469 KBytes
[ 5] 7.00-8.00 sec 91.7 MBytes 769 Mbits/sec 0 469 KBytes
[ 5] 8.00-9.00 sec 99.4 MBytes 834 Mbits/sec 0 747 KBytes
[ 5] 9.00-10.00 sec 101 MBytes 851 Mbits/sec 0 747 KBytes
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Tested-by: Stefan Eichenberger <eichest@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241005112412.544360-4-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In preparation to adding auto negotiation support to mv88q2110 move and
rename the helper function used to write an array of register values to
the PHY.
Just as for mv88q2220 devices this helper will be needed to for the
initial configuration of the mv88q2110 to support auto negotiation.
The function is moved verbatim, there is no change in behavior.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Tested-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://patch.msgid.link/20241005112412.544360-3-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The soft reset implementations for mv88q2110 and mv88q2220 differ as the
later need to consider that auto negation is supported on mv88q2220
devices. In preparation of enabling auto negotiation on mv88q2110 merge
the two rest functions into a device generic one.
The mv88q2220 behavior is kept as is but extended to wait for the reset
bit to be clears before continuing, as was done previously on mv88q2220.
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Tested-by: Dimitri Fedrau <dima.fedrau@gmail.com>
Tested-by: Stefan Eichenberger <eichest@gmail.com>
Link: https://patch.msgid.link/20241005112412.544360-2-niklas.soderlund+renesas@ragnatech.se
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Despite supporting Auto MDI-X, it looks like Aquantia only supports
swapping pair (1,2) with pair (3,6) like it used to be for MDI-X on
100MBit/s networks.
When all 4 pairs are in use (for 1000MBit/s or faster) the link does not
come up with pair order is not configured correctly, either using
MDI_CFG pin or using the "PMA Receive Reserved Vendor Provisioning 1"
register.
Normally, the order of MDI pairs being either ABCD or DCBA is configured
by pulling the MDI_CFG pin.
However, some hardware designs require overriding the value configured
by that bootstrap pin. The PHY allows doing that by setting a bit in
"PMA Receive Reserved Vendor Provisioning 1" register which allows
ignoring the state of the MDI_CFG pin and another bit configuring
whether the order of MDI pairs should be normal (ABCD) or reverse
(DCBA). Pair polarity is not affected and remains identical in both
settings.
Introduce property "marvell,mdi-cfg-order" which allows forcing either
normal or reverse order of the MDI pairs from DT.
If the property isn't present, the behavior is unchanged and MDI pair
order configuration is untouched (ie. either the result of MDI_CFG pin
pull-up/pull-down, or pair order override already configured by the
bootloader before Linux is started).
Forcing normal pair order is required on the Adtran SDG-8733A Wi-Fi 7
residential gateway.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/9ed760ff87d5fc456f31e407ead548bbb754497d.1728058550.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Fold the separate call to clk_set_rate() into the clock getter.
Signed-off-by: Bartosz Golaszewski <bartosz.golaszewski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241007134100.107921-1-brgl@bgdev.pl
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Introduce support for configuring the master/slave role of PHYs based on
the `timing-role` property in the device tree. While this functionality
is necessary for Single Pair Ethernet (SPE) PHYs (1000/100/10Base-T1)
where hardware strap pins may be unavailable or incorrectly set, it
works for any PHY type.
Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Reviewed-by: Florian Fainelli <florian.fainelli@broadcom.com>
Reviewed-by: Divya Koppera <divya.koppera@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
|
|
Commit c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct
ordering") correctly fixed a problem with using devm_ but missed
removing the LED entry from the LEDs list.
This cause kernel panic on specific scenario where the port for the PHY
is torn down and up and the kmod for the PHY is removed.
On setting the port down the first time, the assosiacted LEDs are
correctly unregistered. The associated kmod for the PHY is now removed.
The kmod is now added again and the port is now put up, the associated LED
are registered again.
On putting the port down again for the second time after these step, the
LED list now have 4 elements. With the first 2 already unregistered
previously and the 2 new one registered again.
This cause a kernel panic as the first 2 element should have been
removed.
Fix this by correctly removing the element when LED is unregistered.
Reported-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Daniel Golle <daniel@makrotopia.org>
Cc: stable@vger.kernel.org
Fixes: c938ab4da0eb ("net: phy: Manual remove LEDs to ensure correct ordering")
Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/20241004182759.14032-1-ansuelsmth@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The PHY also support 10MBit/s links as well as the corresponding link
indication trigger to be offloaded. Add TRIGGER_NETDEV_LINK_10 to the
supported triggers.
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://patch.msgid.link/cc5da0a989af8b0d49d823656d88053c4de2ab98.1728057367.git.daniel@makrotopia.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
