summaryrefslogtreecommitdiff
path: root/drivers/net/wireless/ath/ath12k
AgeCommit message (Collapse)Author
2025-02-03wifi: ath12k: update beacon template function to use arvif structureAditya Kumar Singh
The current code has ath12k_wmi_bcn_tmpl() accepting separate ar and vdev_id parameters. However, ath12k_link_vif structure can be used to derive both of these. Hence, simplify the function signature. Later change needs arvif pointer access within the function hence it is better if arvif is directly passed now. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250124-ath12k_mlo_csa-v2-1-420c42fcfecf@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-31wifi: ath12k: remove return for empty tx bitrate in mac_op_sta_statisticsRemi Pommarel
Currently in ath12k_mac_op_sta_statistics() there is the following logic: if (!arsta->txrate.legacy && !arsta->txrate.nss) return; Because ath12k_sta_statistics is used to report many info to iw wlan0 link, if it return for empty legacy and nss of arsta->txrate, then the other stats after it will not be set. To address this issue remove the return and instead invert the logic to set the txrate logic if (arsta->txrate.legacy || arsta->txrate.nss). The same was done also in both ath10k with commit 1cd6ba8ae33e ("ath10k: remove return for NL80211_STA_INFO_TX_BITRATE") and ath11k as well with commit 1d795645e1ee ("ath11k: remove return for empty tx bitrate in mac_op_sta_statistics"). Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Remi Pommarel <repk@triplefau.lt> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/38c2a7c4f7eaf57b9306bb95a9e6c42b7d987e05.1738169458.git.repk@triplefau.lt Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-31wifi: ath12k: fix ath12k_hal_tx_cmd_ext_desc_setup() info1 overrideNicolas Escande
Since inception there is an obvious typo laying around in ath12k_hal_tx_cmd_ext_desc_setup(). Instead of initializing + adding flags to tcl_ext_cmd->info1, we initialize + override. This will be needed in the future to make broadcast frames work with ethernet encapsulation. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.4.1-00199-QCAHKSWPL_SILICONZ-1 Signed-off-by: Nicolas Escande <nico.escande@gmail.com> Reviewed-by: Vasanthakumar Thiagarajan <vasanthakumar.thiagarajan@oss.qualcomm.com> Link: https://patch.msgid.link/20250127071306.1454699-1-nico.escande@gmail.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-29wifi: ath12k: Fetch regdb.bin file from board-2.binAaradhana Sahu
Currently, ath12k_core_fetch_regdb() finds regdb.bin file through board id's but in board-2.bin file regdb.bin file is present with default board id because of which regdb.bin is not fetched. Add support to fetch regdb.bin file from board-2.bin through default board id. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250116032835.118397-1-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-28Merge tag 'ath-current-20250124' of ↵Kalle Valo
git://git.kernel.org/pub/scm/linux/kernel/git/ath/ath ath.git patch for v6.14-rc Fix an issue in the ath12k driver where 6 GHz operation no longer works with new firmware.
2025-01-26wifi: ath12k: Enable monitor ring mask for QCN9274P Praneesh
QCN9274's monitor related rings are initialized properly. Hence enabling the corresponding ring mask in the hardware params. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-15-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Handle monitor drop TLVs scenarioP Praneesh
During monitor destination ring back-pressure, hardware failed to send HAL_RX_PPDU_END_STATUS_DONE TLV. But driver uses this TLV as a delimiter to complete one PPDU worth of data parsing. This causes driver to overwrite the existing PPDU information with the new PPDU information. Fix it by recording the end reason which is provided under each buffer's descriptor in skb->cb and uses it while parsing TLV tags to mark the PPDU end delimiter. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-14-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Avoid memory leak while enabling statisticsP Praneesh
Driver uses monitor destination rings for extended statistics mode and standalone monitor mode. In extended statistics mode, TLVs are parsed from the buffer received from the monitor destination ring and assigned to the ppdu_info structure to update per-packet statistics. In standalone monitor mode, along with per-packet statistics, the packet data (payload) is captured, and the driver updates per MSDU to mac80211. When the AP interface is enabled, only extended statistics mode is activated. As part of enabling monitor rings for collecting statistics, the driver subscribes to HAL_RX_MPDU_START TLV in the filter configuration. This TLV is received from the monitor destination ring, and kzalloc for the mon_mpdu object occurs, which is not freed, leading to a memory leak. The kzalloc for the mon_mpdu object is only required while enabling the standalone monitor interface. This causes a memory leak while enabling extended statistics mode in the driver. Fix this memory leak by removing the kzalloc for the mon_mpdu object in the HAL_RX_MPDU_START TLV handling. Additionally, remove the standalone monitor mode handlings in the HAL_MON_BUF_ADDR and HAL_RX_MSDU_END TLVs. These TLV tags will be handled properly when enabling standalone monitor mode in the future. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-13-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Handle PPDU spread across multiple buffersP Praneesh
Each PPDU contains numerous TLV tags. HAL_RX_PPDU_START marks the start of the PPDU, and HAL_RX_PPDU_END_STATUS_DONE marks the end. From the monitor destination rings, the driver retrieves skb containing these TLV tags and their corresponding data. Sometimes, one PPDU’s information spreads across multiple skbs. The current parsing logic uses memset on struct hal_rx_mon_ppdu_info after parsing each skb, leading to information loss if a PPDU spans multiple skbs. Fix this by setting the ppdu_continuation flag when the driver fails to get HAL_RX_PPDU_END_STATUS_DONE, and do memset on struct hal_rx_mon_ppdu_info only when the ppdu_continuation flag is not set. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-12-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Optimize NAPI budget by adjusting PPDU processingP Praneesh
In the current implementation, when PPDU spans multiple ring descriptors, leading to inefficient use of the NAPI budget. The budget counter is decremented for each ring descriptor, causing rapid depletion of the budget even though the processing of a single PPDU might not be complete. To address this issue, modify the code to decrement the budget counter only when the driver receives HAL_MON_END_OF_PPDU as the end reason. This change ensures that the budget is decremented only once per PPDU, resulting in more efficient utilization of the NAPI budget and better handling of monitor destination ring. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-11-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Handle end reason for the monitor destination ringP Praneesh
Currently, the monitor destination ring's descriptor includes a 2-bit field for the end reason. Out of all the end reason values, hardware uses HAL_MON_FLUSH_DETECTED and HAL_MON_PPDU_TRUNCATED to indicate buffers that should not be processed due to system level errors. Driver should not process entries with these end reasons, as they contain junk values. However, the current code lacks end reason-specific checks for the monitor destination ring, leading to the processing of invalid buffers. Fix this by adding checks for these two end reasons during the reaping phase. Free the skb if either HAL_MON_FLUSH_DETECTED or HAL_MON_PPDU_TRUNCATED is detected, preventing the driver from processing invalid entries. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-10-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Add drop descriptor handling for monitor ringP Praneesh
When monitor block in Hardware experiences internal backpressure, a ring entry with the EMPTY_DESC reason is received in the monitor destination ring descriptor. The cookie field for this corresponding entry is invalid. Currently driver attempts to process this cookie resulting in invalid buf_id warning logs flooding the console. To fix this, skip processing the destination descriptor when the EMPTY_DESCRIPTOR bit is set to true in ring descriptor, thereby avoiding the processing of junk cookies. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-9-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Fix end offset bit definition in monitor ring descriptorP Praneesh
End offset for the monitor destination ring descriptor is defined as 16 bits, while the firmware definition specifies only 12 bits. The remaining bits (bit 12 to bit 15) are reserved and may contain junk values, leading to invalid information retrieval. Fix this issue by updating the correct genmask values. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-8-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Fix invalid entry fetch in ath12k_dp_mon_srng_processP Praneesh
Currently, ath12k_dp_mon_srng_process uses ath12k_hal_srng_src_get_next_entry to fetch the next entry from the destination ring. This is incorrect because ath12k_hal_srng_src_get_next_entry is intended for source rings, not destination rings. This leads to invalid entry fetches, causing potential data corruption or crashes due to accessing incorrect memory locations. This happens because the source ring and destination ring have different handling mechanisms and using the wrong function results in incorrect pointer arithmetic and ring management. To fix this issue, replace the call to ath12k_hal_srng_src_get_next_entry with ath12k_hal_srng_dst_get_next_entry in ath12k_dp_mon_srng_process. This ensures that the correct function is used for fetching entries from the destination ring, preventing invalid memory accesses. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-7-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Restructure the code for monitor ring processingP Praneesh
Currently, monitor ring reaping and processing occur in the same loop, which requires holding ring locks until skb processing is complete. However, only the ring reaping part requires the ring lock; the skb processing part does not need it. This approach is problematic because it unnecessarily extends the duration for which the ring locks are held, leading to increased contention and potential backpressure issues. Fix it by holding ring locks only during the reaping phase, as skb processing does not require them. First, reap the monitor destination ring with the ring lock and queue the skbs into an skb list. Then, process the skbs in this list in a separate loop without holding the ring lock. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-6-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Avoid code duplication in monitor ring processingP Praneesh
The current implementation processes the monitor destination ring using two separate functions, ath12k_dp_mon_srng_process() for standalone monitor mode and ath12k_dp_mon_rx_process_stats() for statistics. However, both functions contain same code which performs monitor ring reaping and skb data processing. To eliminate redundancy, remove the duplicate code and use a single function to handle both the cases. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-5-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Avoid multiple times configuring monitor filterP Praneesh
ath12k_mac_op_configure_filter() gets called multiple times during interface bringup. Applying filter configuration from this function leads to writing same filter configurations multiple times. Resolve this issue by relocating the filter configuration to ath12k_mac_config_mon_status_default(), which is invoked by both ath12k_mac_op_start() and ath12k_mac_op_stop(). Additionally, set the rxmon_disable flag to true when called from ath12k_mac_op_stop() to disable the monitor destination ring. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-4-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Enable filter config for monitor destination ringP Praneesh
Add provision to configure monitor filter for the destination ring. These filters are used for requesting statistics or monitor mode through the monitor destination ring. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-3-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Add HTT source ring ID for monitor ringsP Praneesh
Add source buffer ring and destination buffer ring ID for monitor rings. These IDs are used for ring configuration during initial ring setup. Since monitor rings are enabled based on the rxdma1_enable flag, enable it in the hardware param for the QCN9274 version 2 hardware and increase the destination ring size to handle MSDU data buffers. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: P Praneesh <quic_ppranees@quicinc.com> Link: https://patch.msgid.link/20241223060132.3506372-2-quic_ppranees@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Fix pdev lookup in WBM error processingRameshkumar Sundaram
Currently in ath12k_dp_rx_process_wbm_err(), when processing packets received on the WBM error ring, pdev validation is done based upon the hw_link_id. But hw_link_id corresponds to link id of a given partner pdev in a MLO hardware group, and is not the correct index to use to lookup a pdev in an SoC(ab). As a result, pdev validation fails, and the reaped packets are dropped instead of being processed. The correct index to use is the pdev_id, which is already derived in the function. So update the logic to validate the pdev based upon the pdev_id instead of the hw_link_id. This matches the logic used in other Rx ring processing functions. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: 1a73acb5fba4 ("wifi: ath12k: move to HW link id based receive handling") Signed-off-by: Rameshkumar Sundaram <quic_ramess@quicinc.com> Link: https://patch.msgid.link/20250102043048.2596791-1-quic_ramess@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Request pdev stats from firmwareRamya Gnanasekar
Add support to request pdev stats from firmware through WMI and print the information Sample Output: ------------- cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/fw_stats/pdev_stats ath12k PDEV stats ================= Channel noise floor -85 Channel TX power 126 TX frame count 0 RX frame count 8637 RX clear count 37424 Cycle count 4372024 PHY error count 0 soc drop count 0 ath12k PDEV TX stats ==================== HTT cookies queued 0 HTT cookies disp. 0 MSDU queued 0 MPDU queued 0 MSDUs dropped 0 Local enqued 0 Local freed 0 HW queued 0 PPDUs reaped 0 Num underruns 0 PPDUs cleaned 0 MPDUs requeued 0 Excessive retries 0 HW rate 0 Sched self triggers 0 Dropped due to SW retries 0 Illegal rate phy errors 0 PDEV continuous xretry 0 TX timeout 9 PDEV resets 0 Stateless TIDs alloc failures 0 PHY underrun 0 MPDU is more than txop limit 0 ath12k PDEV RX stats ==================== Mid PPDU route change 0 Tot. number of statuses 0 Extra frags on rings 0 0 Extra frags on rings 1 0 Extra frags on rings 2 0 Extra frags on rings 3 0 MSDUs delivered to HTT 0 MPDUs delivered to HTT 0 MSDUs delivered to stack 0 MPDUs delivered to stack 0 Oversized AMSUs 0 PHY errors 0 PHY errors drops 0 MPDU errors (FCS, MIC, ENC) 0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250124185330.1244585-4-ramya.gnanasekar@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Request beacon stats from firmwareRamya Gnanasekar
Add support to request and dump beacon statistics from firmware Sample output: ------------- cat /sys/kernel/debug/ath12k/pci-0000:06:00.0/mac0/fw_stats/beacon_stats ath12k Beacon stats (1) =================== VDEV ID 0 VDEV MAC address 00:03:7f:04:37:58 ================ Num of beacon tx success 20 Num of beacon tx failures 0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250124185330.1244585-3-ramya.gnanasekar@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: Request vdev stats from firmwareRamya Gnanasekar
Add support to request and print vdev stats from firmware through WMI. Sample output: ------------- cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/fw_stats/vdev_stats ath12k VDEV stats ================= VDEV ID 0 VDEV MAC address 00:03:7f:6c:9c:1a beacon snr 96 data snr 255 num rx frames 0 num rts fail 0 num rts success 0 num rx err 0 num rx discard 0 num tx not acked 0 num tx frames [00] 0 num tx frames [01] 0 num tx frames [02] 0 num tx frames [03] 2 num tx frames retries [00] 0 num tx frames retries [01] 0 num tx frames retries [02] 0 num tx frames retries [03] 0 num tx frames failures [00] 0 num tx frames failures [01] 0 num tx frames failures [02] 0 num tx frames failures [03] 0 tx rate history [00] 0x00000000 tx rate history [01] 0x00000000 tx rate history [02] 0x00000000 tx rate history [03] 0x00000000 tx rate history [04] 0x00000000 tx rate history [05] 0x00000000 tx rate history [06] 0x00000000 tx rate history [07] 0x00000000 tx rate history [08] 0x00000000 tx rate history [09] 0x00000000 beacon rssi history [00] 0 beacon rssi history [01] 0 beacon rssi history [02] 0 beacon rssi history [03] 0 beacon rssi history [04] 0 beacon rssi history [05] 0 beacon rssi history [06] 0 beacon rssi history [07] 0 beacon rssi history [08] 0 beacon rssi history [09] 0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Ramya Gnanasekar <ramya.gnanasekar@oss.qualcomm.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250124185330.1244585-2-ramya.gnanasekar@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: fix memory leak in ath12k_pci_remove()Miaoqing Pan
Kmemleak reported this error: unreferenced object 0xffff1c165cec3060 (size 32): comm "insmod", pid 560, jiffies 4296964570 (age 235.596s) backtrace: [<000000005434db68>] __kmem_cache_alloc_node+0x1f4/0x2c0 [<000000001203b155>] kmalloc_trace+0x40/0x88 [<0000000028adc9c8>] _request_firmware+0xb8/0x608 [<00000000cad1aef7>] firmware_request_nowarn+0x50/0x80 [<000000005011a682>] local_pci_probe+0x48/0xd0 [<00000000077cd295>] pci_device_probe+0xb4/0x200 [<0000000087184c94>] really_probe+0x150/0x2c0 The firmware memory was allocated in ath12k_pci_probe(), but not freed in ath12k_pci_remove() in case ATH12K_FLAG_QMI_FAIL bit is set. So call ath12k_fw_unmap() to free the memory. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.2.0-02280-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1 Signed-off-by: Miaoqing Pan <quic_miaoqing@quicinc.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250123080226.1116479-1-quic_miaoqing@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: encode max Tx power in scan channel list commandSathishkumar Muruganandam
Currently, when sending the scan channel list command to the firmware, the maximum Tx power is not encoded in the reg2 member. This omission causes the firmware to be unaware of the host's maximum Tx power, leading to incorrect Tx power derivation at firmware level. To resolve this issue, encode the maximum Tx power in the scan channel list command before sending it to firmware. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com> Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Tested-by: Nicolas Escande <nico.escande@gmail.com> Link: https://patch.msgid.link/20250107-add_max_reg_pwr_in_scan_ch_list_cmd-v1-1-70d9963a21e4@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: report station mode signal strengthLingbo Kong
Currently, the signal strength of "iw dev xxx station dump" always show an invalid value. This is because signal strength is only set in ath12k_mgmt_rx_event() function, and not set for received data packet. So, change to get signal from firmware and report to mac80211. After that, "iw dev xxx station dump" show the correct signal strength. Such as: Station 00:03:7f:12:03:03 (on wlo1) inactive time: 36 ms rx bytes: 61571 rx packets: 336 tx bytes: 28204 tx packets: 205 tx retries: 49 tx failed: 0 beacon loss: 0 beacon rx: 83 rx drop misc: 66 signal: -24 dBm beacon signal avg: -22 dBm For WCN7850, the firmware supports db2dbm, so not need to add noise floor. For QCN9274, the firmware not support db2dbm, so need to add noise floor. This patch affects the station mode of WCN7850 and QCN9274. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Link: https://patch.msgid.link/20250115063537.35797-4-quic_lingbok@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: report station mode receive rate for IEEE 802.11beLingbo Kong
Currently, the receive rate of EHT of "iw dev xxx station dump" command always show an invalid value. This is because ath12k does not pass information about the rx_status of EHT to mac80211. So, mac80211 not calculate the receive rate. To address this issue, add logic for handling rx_status of EHT to the ath12k_dp_rx_h_rate() function. After that, "iw dev xxx station dump" show the correct receive rate. Such as: Station 00:03:7f:12:03:03 (on wlo1) inactive time: 48 ms rx bytes: 59226 rx packets: 320 tx bytes: 26556 tx packets: 191 tx retries: 99 tx failed: 0 beacon loss: 0 beacon rx: 79 rx drop misc: 68 signal: -95 dBm beacon signal avg: -20 dBm tx bitrate: 688.2 MBit/s 40MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0 tx duration: 0 us rx bitrate: 619.5 MBit/s 40MHz EHT-MCS 8 EHT-NSS 3 EHT-GI 0 This patch affects the station mode of WCN7850 and QCN9274. Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715 Link: https://patch.msgid.link/20250115063537.35797-3-quic_lingbok@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-26wifi: ath12k: report station mode transmit rateLingbo Kong
Currently, the transmit rate of "iw dev xxx station dump" command always show an invalid value. To address this issue, ath12k parse the info of transmit complete report from firmware and indicate the transmit rate to mac80211. This patch affects the station mode of WCN7850 and QCN9274. After that, "iw dev xxx station dump" show the correct transmit rate. Such as: Station 00:03:7f:12:03:03 (on wlo1) inactive time: 872 ms rx bytes: 219111 rx packets: 1133 tx bytes: 53767 tx packets: 462 tx retries: 51 tx failed: 0 beacon loss: 0 beacon rx: 403 rx drop misc: 74 signal: -95 dBm beacon signal avg: -18 dBm tx bitrate: 1441.1 MBit/s 80MHz EHT-MCS 13 EHT-NSS 2 EHT-GI 0 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Signed-off-by: Lingbo Kong <quic_lingbok@quicinc.com> Closes: https://bugzilla.kernel.org/show_bug.cgi?id=219715 Link: https://patch.msgid.link/20250115063537.35797-2-quic_lingbok@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-24wifi: ath12k: fix handling of 6 GHz rulesAditya Kumar Singh
In the US country code, to avoid including 6 GHz rules in the 5 GHz rules list, the number of 5 GHz rules is set to a default constant value of 4 (REG_US_5G_NUM_REG_RULES). However, if there are more than 4 valid 5 GHz rules, the current logic will bypass the legitimate 6 GHz rules. For example, if there are 5 valid 5 GHz rules and 1 valid 6 GHz rule, the current logic will only consider 4 of the 5 GHz rules, treating the last valid rule as a 6 GHz rule. Consequently, the actual 6 GHz rule is never processed, leading to the eventual disabling of 6 GHz channels. To fix this issue, instead of hardcoding the value to 4, use a helper function to determine the number of 6 GHz rules present in the 5 GHz rules list and ignore only those rules. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Cc: stable@vger.kernel.org Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Signed-off-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250123-fix_6ghz_rules_handling-v1-1-d734bfa58ff4@oss.qualcomm.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-23wifi: ath12k: fix skb_ext_desc leak in ath12k_dp_tx() error pathNicolas Escande
When vlan support was added, we missed that when ath12k_dp_prepare_htt_metadata() returns an error we also need to free the skb holding the metadata before going on with the cleanup process. Compile tested only. Fixes: 26dd8ccdba4d ("wifi: ath12k: dynamic VLAN support") Signed-off-by: Nicolas Escande <nico.escande@gmail.com> Reviewed-by: Aditya Kumar Singh <aditya.kumar.singh@oss.qualcomm.com> Link: https://patch.msgid.link/20250122160112.3234558-1-nico.escande@gmail.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-22wifi: ath12k: Disable MLO in Factory Test ModeAaradhana Sahu
Factory test mode(FTM) is supported only in non-MLO(multi-link operation) mode. Therefore, disable MLO when driver boots in FTM mode. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250119083657.1937557-5-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-22wifi: ath12k: add factory test mode supportAaradhana Sahu
Add support to process factory test mode commands(FTM) for calibration. By default firmware start with MISSION mode and to process the FTM commands firmware needs to be restarted in FTM mode using module parameter ftm_mode. The pre-request is all the radios should be down before starting the test. All ath12k test mode interface related commands specified in enum ath_tm_cmd. When start command ATH_TM_CMD_TESTMODE_START is received, ar state is set to test Mode and FTM daemon sends test mode command to wifi driver via cfg80211. Wifi driver sends these command to firmware as wmi events. If it is segmented commands it will be broken down into multiple segments and encoded with TLV header else it is sent to firmware as it is. Firmware response via UTF events, wifi driver creates skb and send to cfg80211, cfg80211 sends firmware response to FTM daemon via netlink message. Command to boot in ftm mode insmod ath12k ftm_mode=1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250119083657.1937557-4-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-22wifi: ath12k: export ath12k_wmi_tlv_hdr for testmodeAaradhana Sahu
Export ath12k_wmi_tlv_hdr() to further use in the testmode command processing. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aaradhana Sahu <quic_aarasahu@quicinc.com> Reviewed-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Link: https://patch.msgid.link/20250119083657.1937557-3-quic_aarasahu@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-17wifi: ath12k: Refactor Rx status TLV parsing procedure argumentKarthikeyan Periyasamy
Currently, ath12k_dp_mon_rx_parse_status_tlv() takes the TLV tag, TLV data and TLV userid as separate arguments from the caller. In the future, the TLV length will be needed for parsing the EHT TLV tag. Therefore, instead of increasing the number of arguments, pass the TLV header and retrieve the necessary fields from the TLV header itself. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241224143613.164921-4-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-17wifi: ath12k: Refactor the monitor Tx/RX handler procedure argumentsKarthikeyan Periyasamy
Currently, the pdev handle is given along with the mac id to all the monitor Tx/Rx handler procedure arguments. The mac id information is derived from the pdev handle itself. Therefore, remove the unnecessary mac id argument from the handler. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241224143613.164921-3-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-17wifi: ath12k: Refactor the monitor Rx parser handler argumentKarthikeyan Periyasamy
Currently, the monitor Rx parser handlers ath12k_dp_mon_rx_parse_status_tlv() and ath12k_dp_mon_parse_rx_dest() take the device handle from the caller. However, these handlers functionality is technically pdev specific. Additionally, the device handle can be retrieved from the pdev handle. Therefore, for better code understanding, change the monitor Rx parser handlers argument from the device handle to the pdev handle. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241224143613.164921-2-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: fix key cache handlingAditya Kumar Singh
Currently, an interface is created in the driver during channel assignment. If mac80211 attempts to set a key for an interface before this assignment, the driver caches the key. Once the interface is created, the driver installs the cached key to the hardware. This sequence is exemplified in mesh mode operation where the group key is set before channel assignment. However, in ath12k_mac_update_key_cache(), after caching the key, due to incorrect logic, it is deleted from the cache during the subsequent loop iteration. As a result, after the interface is created, the driver does not find any cached key, and the key is not installed to the hardware which is wrong. This leads to issue in mesh, where broadcast traffic is not encrypted over the air. Fix this issue by adjusting the logic of ath12k_mac_update_key_cache() properly. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3-03253.1-QCAHKSWPL_SILICONZ-29 # Nicolas Escande <nico.escande@gmail.com> Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 # Nicolas Escande <nico.escande@gmail.com> Fixes: 25e18b9d6b4b ("wifi: ath12k: modify ath12k_mac_op_set_key() for MLO") Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Tested-by: Nicolas Escande <nico.escande@gmail.com> Link: https://patch.msgid.link/20250112-fix_key_cache_handling-v2-1-70e142c6153e@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Fix uninitialized variable access in ath12k_mac_allocate() ↵Karthikeyan Periyasamy
function Currently, the uninitialized variable 'ab' is accessed in the ath12k_mac_allocate() function. Initialize 'ab' with the first radio device present in the hardware abstraction handle (ah). Additionally, move the default setting procedure from the pdev mapping iteration to the total radio calculating iteration for better code readability. Perform the maximum radio validation check for total_radio to ensure that both num_hw and radio_per_hw are validated indirectly, as these variables are derived from total_radio. This also fixes the below Smatch static checker warning. Smatch warning: ath12k_mac_allocate() error: uninitialized symbol 'ab' Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group") Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20250112071630.4059410-5-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Remove ath12k_get_num_hw() helper functionKarthikeyan Periyasamy
Currently, the ath12k_get_num_hw() helper function takes the device handle as an argument. Here, the number of hardware is retrieved from the group handle. Demanding the device handle from the caller is unnecessary since in some cases the group handle is already available. Additionally, there is no longer a need for multiple indirections to get the number of hardware. Therefore, remove this helper function and directly use ag->num_hw. This change also fixes the below Smatch static checker warning. Smatch warning: ath12k_mac_destroy() error: we previously assumed 'ab' could be null Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Reported-by: Dan Carpenter <dan.carpenter@linaro.org> Closes: https://lore.kernel.org/ath12k/3e705de0-67d1-4437-97ff-4828d83ae2af@stanley.mountain/ Closes: https://scan7.scan.coverity.com/#/project-view/52682/11354?selectedIssue=1602340 Fixes: a343d97f27f5 ("wifi: ath12k: move struct ath12k_hw from per device to group") Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Link: https://patch.msgid.link/20250112071630.4059410-4-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Refactor the ath12k_hw get helper function argumentKarthikeyan Periyasamy
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the ath12k_hw get helper function takes the device handle and the index as parameters. Here, the index parameter is specific to the group handle. Therefore, change this helper function argument from the device handle to the group handle. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20250112071630.4059410-3-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-14wifi: ath12k: Refactor ath12k_hw set helper function argumentKarthikeyan Periyasamy
Currently, ath12k_hw is placed inside the ath12k_hw_group. However, the ath12k_hw set helper function takes the device handle and the index as parameters. Here, the index parameter is specific to the group handle. Therefore, change this helper function argument from the device handle to the group handle. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Karthikeyan Periyasamy <quic_periyasa@quicinc.com> Acked-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20250112071630.4059410-2-quic_periyasa@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-10wifi: ath12k: Support pdev Puncture StatsRajat Soni
Add support to request pdev puncture stats from firmware through HTT stats type 46. These stats give the count of number of subbands used in different wifi standards. Sample output: ------------- echo 46 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats HTT_PDEV_PUNCTURE_STATS_TLV: mac_id = 0 tx_ofdm_su_last_used_pattern_mask = 0x00000001 tx_ofdm_su_num_subbands_used_cnt_01 = 217 tx_ofdm_su_num_subbands_used_cnt_02 = 0 tx_ofdm_su_num_subbands_used_cnt_03 = 0 ..... HTT_PDEV_PUNCTURE_STATS_TLV: mac_id = 0 tx_ax_dl_mu_ofdma_last_used_pattern_mask = 0x00000000 tx_ax_dl_mu_ofdma_num_subbands_used_cnt_01 = 0 tx_ax_dl_mu_ofdma_num_subbands_used_cnt_02 = 0 tx_ax_dl_mu_ofdma_num_subbands_used_cnt_03 = 0 ..... HTT_PDEV_PUNCTURE_STATS_TLV: mac_id = 0 tx_be_dl_mu_ofdma_last_used_pattern_mask = 0x00000000 tx_be_dl_mu_ofdma_num_subbands_used_cnt_01 = 0 tx_be_dl_mu_ofdma_num_subbands_used_cnt_02 = 0 tx_be_dl_mu_ofdma_num_subbands_used_cnt_03 = 0 ..... HTT_PDEV_PUNCTURE_STATS_TLV: mac_id = 0 rx_ax_ul_mu_ofdma_last_used_pattern_mask = 0x00000000 rx_ax_ul_mu_ofdma_num_subbands_used_cnt_01 = 0 rx_ax_ul_mu_ofdma_num_subbands_used_cnt_02 = 0 rx_ax_ul_mu_ofdma_num_subbands_used_cnt_03 = 0 ..... HTT_PDEV_PUNCTURE_STATS_TLV: mac_id = 0 rx_be_ul_mu_ofdma_last_used_pattern_mask = 0x00000000 rx_be_ul_mu_ofdma_num_subbands_used_cnt_01 = 0 rx_be_ul_mu_ofdma_num_subbands_used_cnt_02 = 0 rx_be_ul_mu_ofdma_num_subbands_used_cnt_03 = 0 ..... Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Rajat Soni <quic_rajson@quicinc.com> Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241218035711.2573584-3-quic_rdevanat@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-10wifi: ath12k: Support AST Entry StatsRoopni Devanathan
Add support to request Address Search Table(AST) entries stats from firmware through HTT stats type 41. These stats give AST entries related information such as software peer id, MAC address, pdev id, vdev, id, next hop, etc. Sample output: ------------- echo 41 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats HTT_AST_ENTRY_TLV: ast_index = 10 mac_addr = 00:00:00:01:00:00 sw_peer_id = 0 pdev_id = 3 vdev_id = 255 next_hop = 0 mcast = 0 monitor_direct = 0 mesh_sta = 0 mec = 0 intra_bss = 0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241218035711.2573584-2-quic_rdevanat@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-10wifi: ath12k: Support Transmit Buffer OFDMA StatsPradeep Kumar Chitrapu
Add support to request OFDMA stats of transmit buffers from firmware through HTT stats type 32. These stats give information about NDPA, NDP, BRP and steering mechanisms. Note: WCN7850 firmware version - WLAN.HMT.1.0-03427-QCAHMTSWPL_V1.0_V2.0_SILICONZ-1.15378.4 does not support HTT stats type 32. Sample output: ------------- echo 32 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats HTT_TXBF_OFDMA_AX_NDPA_STATS_TLV: ax_ofdma_ndpa_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ax_ofdma_ndpa_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ..... HTT_TXBF_OFDMA_AX_NDP_STATS_TLV: ax_ofdma_ndp_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ax_ofdma_ndp_tried = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ..... HTT_TXBF_OFDMA_AX_BRP_STATS_TLV: ax_ofdma_brpoll_queued = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ax_ofdma_brpoll_tied = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ..... HTT_TXBF_OFDMA_AX_STEER_STATS_TLV: ax_ofdma_num_ppdu_steer = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ax_ofdma_num_usrs_prefetch = 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0, 14:0, 15:0, 16:0, 17:0, 18:0, 19:0, 20:0, 21:0, 22:0, 23:0, 24:0, 25:0, 26:0, 27:0, 28:0, 29:0, 30:0, 31:0, 32:0, 33:0, 34:0, 35:0, 36:0, 37:0 ..... HTT_TXBF_OFDMA_AX_STEER_MPDU_STATS_TLV: rbo_steer_mpdus_tried = 0 rbo_steer_mpdus_failed = 0 sifs_steer_mpdus_tried = 0 sifs_steer_mpdus_failed = 0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com> Acked-by: Jeff Johnson <jjohnson@kernel.org> Link: https://patch.msgid.link/20241128110949.3672364-3-quic_rdevanat@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-10wifi: ath12k: Support Transmit Rate Buffer StatsPradeep Kumar Chitrapu
Add support to request transmit rate buffer stats from firmware through HTT stats type 31. These stats give information such as MCS, NSS and bandwidth of transmit and input buffer. Sample output: ------------- echo 31 > /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats_type cat /sys/kernel/debug/ath12k/pci-0000\:06\:00.0/mac0/htt_stats HTT_STATS_PDEV_TX_RATE_TXBF_STATS: Legacy OFDM Rates: 6 Mbps: 0, 9 Mbps: 0, 12 Mbps: 0, 18 Mbps: 0 24 Mbps: 0, 36 Mbps: 0, 48 Mbps: 0, 54 Mbps: 0 tx_ol_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0 tx_ibf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0 tx_txbf_mcs = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0, 8:0, 9:0, 10:0, 11:0, 12:0, 13:0 tx_ol_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0 tx_ibf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0 tx_txbf_nss = 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0 tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0 half_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0 quarter_tx_ol_bw = 0:0, 1:0, 2:0, 3:0, 4:0 tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 half_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 quarter_tx_ibf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 half_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 quarter_tx_txbf_bw = 0:0, 1:0, 2:0, 3:0, 4:0 HTT_STATS_PDEV_TXBF_FLAG_RETURN_STATS: TXBF_reason_code_stats: 0:0, 1:0, 2:0, 3:0, 4:0, 5:0, 6:0, 7:0 Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Pradeep Kumar Chitrapu <quic_pradeepc@quicinc.com> Signed-off-by: Roopni Devanathan <quic_rdevanat@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Acked-by: Jeff Johnson <jjohnson@kernel.org> Link: https://patch.msgid.link/20241128110949.3672364-2-quic_rdevanat@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-07wifi: ath12k: fix tx power, max reg power update to firmwareSathishkumar Muruganandam
Currently, when the vdev start WMI cmd is sent from host, vdev related parameters such as max_reg_power, max_power, and max_antenna_gain are multiplied by 2 before being sent to the firmware. This is incorrect because the firmware uses 1 dBm steps for power calculations. This leads to incorrect power values being used in the firmware and radio, potentially causing incorrect behavior. Fix the update of max_reg_power, max_power, and max_antenna_gain values in the ath12k_mac_vdev_start_restart function, ensuring accurate power settings in the firmware by sending these values as-is, without multiplication. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.1.1-00214-QCAHKSWPL_SILICONZ-1 Tested-on: WCN7850 hw2.0 PCI WLAN.HMT.1.0.c5-00481-QCAHMTSWPL_V1.0_V2.0_SILICONZ-3 Signed-off-by: Sathishkumar Muruganandam <quic_murugana@quicinc.com> Signed-off-by: Santhosh Ramesh <quic_santrame@quicinc.com> Fixes: d889913205cf ("wifi: ath12k: driver for Qualcomm Wi-Fi 7 devices") Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20240909073049.3423035-1-quic_santrame@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-07wifi: ath12k: set flag for mgmt no-ack frames in Tx completionRamya Gnanasekar
IEEE80211_TX_STAT_NOACK_TRANSMITTED flag signifies that frame was successfully transmitted without any errors when no-ack is requested. In WMI Tx management completion path, driver is not setting IEEE80211_TX_STAT_NOACK_TRANSMITTED flag for the frames with IEEE80211_TX_CTL_NO_ACK. Without this flag, the management frame statistics will not track such frames. Add IEEE80211_TX_STAT_NOACK_TRANSMITTED flag as part of the flags in skb transmit information when WMI is processing Tx completion for management frames. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.0.1-00029-QCAHKSWPL_SILICONZ-1 Signed-off-by: Ramya Gnanasekar <quic_rgnanase@quicinc.com> Signed-off-by: Muna Sinada <quic_msinada@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241219190845.605116-1-quic_msinada@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-07wifi: ath12k: Include MLO memory in firmware coredump collectionRaj Kumar Bhagat
The current firmware coredump collection in ath12k does not include the MLO_GLOBAL_MEM_REGION_TYPE memory. This memory region is essential for debugging issues related to Multi-Link Operation (MLO). Hence, add support to include MLO_GLOBAL_MEM_REGION_TYPE memory in firmware coredump collection. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Raj Kumar Bhagat <quic_rajkbhag@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241218040149.4041728-1-quic_rajkbhag@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-07wifi: ath12k: handle radar detection with MLOAditya Kumar Singh
ieee80211_radar_detected() expects the driver to pass a channel context configuration during MLO. This is used to identify exactly which link detected the radar. Add support to pass this to mac80211. Since the link arvif is not known in the WMI event, introduce a helper iterator API, ath12k_mac_get_any_chanctx_conf_iter(), to get the channel context configuration. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-3-058e783bcfc7@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
2025-01-07wifi: ath12k: fix CAC running state during virtual interface startAditya Kumar Singh
Currently, the DFS CAC time and the usable state of the primary channel in the channel definition are used to set the CAC_RUNNING flag for the ath12k radio structure. However, this approach is flawed because there are channel definitions where the primary channel is not a DFS channel, but the secondary channel is. For example, in 5 GHz band, channel 36 with 160 MHz bandwidth. In such cases, the flag is not set correctly and hence places where this flag is tested will not operate as expected. For example, Rx packets will not be dropped. To fix this issue, use the cfg80211_chandef_dfs_usable() function from cfg80211, which returns true if at least one channel is in a usable state. This will ensure the CAC_RUNNING flag is set properly. Additionally, update the CAC running debug log message to include the CAC time in milliseconds and also print the center frequency segment 1. Tested-on: QCN9274 hw2.0 PCI WLAN.WBE.1.3.1-00173-QCAHKSWPL_SILICONZ-1 Signed-off-by: Aditya Kumar Singh <quic_adisi@quicinc.com> Acked-by: Kalle Valo <kvalo@kernel.org> Link: https://patch.msgid.link/20241218-ath12k_mlo_dfs-v1-2-058e783bcfc7@quicinc.com Signed-off-by: Jeff Johnson <jeff.johnson@oss.qualcomm.com>
generated by cgit (git 2.34.1) at 2025-09-21 20:30:55 +0000