| Age | Commit message (Collapse) | Author |
|---|
|
Since de77ecd4ef02 ("bonding: improve link-status update in
mii-monitoring"), the bonding driver has utilized two separate variables
to indicate the next link state a particular slave should transition to.
Each is used to communicate to a different portion of the link state
change commit logic; one to the bond_miimon_commit function itself, and
another to the state transition logic.
Unfortunately, the two variables can become unsynchronized,
resulting in incorrect link state transitions within bonding. This can
cause slaves to become stuck in an incorrect link state until a
subsequent carrier state transition.
The issue occurs when a special case in bond_slave_netdev_event
sets slave->link directly to BOND_LINK_FAIL. On the next pass through
bond_miimon_inspect after the slave goes carrier up, the BOND_LINK_FAIL
case will set the proposed next state (link_new_state) to BOND_LINK_UP,
but the new_link to BOND_LINK_DOWN. The setting of the final link state
from new_link comes after that from link_new_state, and so the slave
will end up incorrectly in _DOWN state.
Resolve this by combining the two variables into one.
Reported-by: Aleksei Zakharov <zakharov.a.g@yandex.ru>
Reported-by: Sha Zhang <zhangsha.zhang@huawei.com>
Cc: Mahesh Bandewar <maheshb@google.com>
Fixes: de77ecd4ef02 ("bonding: improve link-status update in mii-monitoring")
Signed-off-by: Jay Vosburgh <jay.vosburgh@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since RSS hash is available from the host, record it in
the skb.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the driver needs to create a hash value because it
was not done at higher level, then the hash should be marked
as a software not hardware hash.
Fixes: f72860afa2e3 ("hv_netvsc: Exclude non-TCP port numbers from vRSS hashing")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
100GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains updates to the ice driver only.
Anirudh refactors the code to reduce the kernel configuration flags and
introduces ice_base.c file.
Maciej does additional refactoring on the configuring of transmit
rings so that we are not configuring per each traffic class flow.
Added support for XDP in the ice driver. Provides additional
re-organizing of the code in preparation for adding build_skb() support
in the driver. Adjusted the computational padding logic for headroom
and tailroom to better support build_skb(), which also aligns with the
logic in other Intel LAN drivers. Added build_skb support and make use
of the XDP's data_meta.
Krzysztof refactors the driver to prepare for AF_XDP support in the
driver and then adds support for AF_XDP.
v2: Updated patch 3 of the series based on community feedback with the
following changes...
- return -EOPNOTSUPP instead of ENOTSUPP for too large MTU which makes
it impossible to attach XDP prog
- don't check for case when there's no XDP prog currently on interface
and ice_xdp() is called with NULL bpf_prog; this happens when user
does "ip link set eth0 xdp off" and no prog is present on VSI; no need
for that as it is handled by higher layer
- drop the extack message for unknown xdp->command
- use the smp_processor_id() for accessing the XDP Tx ring for XDP_TX
action
- don't leave the interface in downed state in case of any failure
during the XDP Tx resources handling
- undo rename of ice_build_ctob
The above changes caused a ripple effect in patches 4 & 5 to update
references to ice_build_ctob() which are now build_ctob()
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/next-queue
Jeff Kirsher says:
====================
10GbE Intel Wired LAN Driver Updates 2019-11-04
This series contains old Halloween candy updates, yet still sweet, to
fm10k, ixgbe and i40e.
Jake adds the missing initializers for a couple of the TLV attribute
macros. Added support for capturing and reporting statistics for all of
the VFs in a given PF. Lastly, bump the version of the fm10k driver to
reflect the recent changes.
Alex addresses locality issues in the ixgbe driver when it is loaded on
a system supporting multiple NUMA nodes.
Manjunath Patil provides changes to the ixgbe driver, similar to those
made to igb, to prevent transmit packets to request a hardware timestamp
when the NIC has not been setup via the SIOCSHWTSTAMP ioctl.
Alice adds support for x710 by adding the missing device id's in the
appropriate places to ensure all the features are enabled in i40e.
Jesse adds support for VF stats gathering in the i40e via the kernel
via ndo_get_vf_stats function.
v2: Fixed up commit id references in patch 5's description to align with
how commit id's should be referenced.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
condition
In mcp251x_restart_work_handler() the variable to stop the interrupt
handler (priv->force_quit) is reset after the chip is restarted and thus
a interrupt might occur.
This patch fixes the potential race condition by resetting force_quit
before enabling interrupts.
Signed-off-by: Timo Schlüßler <schluessler@krause.de>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Implement the VF stats gathering via the kernel via ndo_get_vf_stats().
The driver will show per-VF stats in the output of the command:
ip -s link show dev <PF>
Testing Hints:
ip -s link show dev eth0
will return non-zero VF stats.
...
vf 0 MAC 00:55:aa:00:55:aa, spoof checking on, link-state enable, trust off
RX: bytes packets mcast bcast
128000 1000 104 104
TX: bytes packets
128000 1000
Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The I40E_DEV_ID_10G_BASE_T_BC device id was added previously,
but was not enabled in all the appropriate places. Adding it
to enable it's use.
Signed-off-by: Alice Michael <alice.michael@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
HW timestamping can only be requested for a packet if the NIC is first
setup via ioctl(SIOCSHWTSTAMP). If this step was skipped, then the ixgbe
driver still allowed TX packets to request HW timestamping. In this
situation, we see 'clearing Tx Timestamp hang' noise in the log.
Fix this by checking that the NIC is configured for HW TX timestamping
before accepting a HW TX timestamping request.
Similar-to:
commit 26bd4e2db06b ("igb: protect TX timestamping from API misuse")
commit 0a6f2f05a2f5 ("igb: Fix a test with HWTSTAMP_TX_ON")
Signed-off-by: Manjunath Patil <manjunath.b.patil@oracle.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
An upcoming out-of-tree release will be occurring which will include the
recent functionality to support virtual function statistics. Update the
kernel driver version to match this.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This patch is meant to address locality issues present in the ixgbe driver
when it is loaded on a system supporting multiple NUMA nodes and more CPUs
then the device can map in a 1:1 fashion. Instead of just arbitrarily
mapping itself to CPUs 0-62 it would make much more sense to map itself to
the local CPUs first, and then map itself to any remaining CPUs that might
be used.
The first effect of this is that queue 0 should always be allocated on the
local CPU/NUMA node. This is important as it is the default destination if
a packet doesn't match any existing flow director filter or RSS rule and as
such having it local should help to reduce QPI cross-talk in the event of
an unrecognized traffic type.
In addition this should increase the likelihood of the RSS queues being
allocated and used on CPUs local to the device while the ATR/Flow Director
queues would be able to route traffic directly to the CPU that is likely to
be processing it.
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Support capturing and reporting statistics for all of the VFs associated
with a given PF device via the ndo_get_vf_stats callback.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add the missing field initializers for a couple of the TLV attribute
macros. This resolves the last few -Wmissing-field-initializers warnings
for the fm10k Linux driver.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
At this point ice driver is able to work on order 1 pages that are split
onto two 3k buffers. Let's reflect that when user is setting new MTU
size and XDP is present on interface.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Driver is now prepared for building the skb around the existing Rx
buffer, so introduce the ice_build_skb responsible for it. Make use of
XDP's data_meta as well.
I've observed around 30% less CPU consumption with build_skb Rx path, in
comparison to legacy Rx. What stands behind such result is the avoidance
of flow_dissector (which we were diving into via eth_get_headlen) and no
memcpy calls.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Take into account the underlying architecture specific settings and
based on that calculate the possible padding that can be supplied.
Typically, for x86 and standard MTU size we will end up with 192 bytes
of headroom. This is the same behavior as our other drivers have and we
can dedicate it for XDP purposes.
Furthermore, introduce the Rx ring flag for indicating whether build_skb
is used on particular. Based on that invoke the routines for padding
calculation.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Add an ethtool "legacy-rx" priv flag for toggling the Rx path. This
control knob will be mainly used for build_skb usage as well as buffer
size/MTU manipulation.
In preparation for adding build_skb support in a way that it takes
care of how we set the values of max_frame and rx_buf_len fields of
struct ice_vsi. Specifically, in this patch mentioned fields are set to
values that will allow us to provide headroom and tailroom in-place.
This can be mostly broken down onto following:
- for legacy-rx "on" ethtool control knob, old behaviour is kept;
- for standard 1500 MTU size configure the buffer of size 1536, as
network stack is expecting the NET_SKB_PAD to be provided and
NET_IP_ALIGN can have a non-zero value (these can be typically equal
to 32 and 2, respectively);
- for larger MTUs go with max_frame set to 9k and configure the 3k
buffer in case when PAGE_SIZE of underlying arch is less than 8k; 3k
buffer is implying the need for order 1 page, so that our page
recycling scheme can still be applied;
With that said, substitute the hardcoded ICE_RXBUF_2048 and PAGE_SIZE
values in DMA API that we're making use of with rx_ring->rx_buf_len and
ice_rx_pg_size(rx_ring). The latter is an introduced helper for
determining the page size based on its order (which was figured out via
ice_rx_pg_order). Last but not least, take care of truesize calculation.
In the followup patch the headroom/tailroom computation logic will be
introduced.
This change aligns the buffer and frame configuration with other Intel
drivers, most importantly with iavf.
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While the ti_hecc has interrupts to report when the error counters increase
to a certain level and which change state it doesn't handle the case that
the error counters go down again, so the reported state can actually be
wrong. Since there is no interrupt for that, do update state based on the
error counters, when the state is not error active and goes down again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANES register handles the flags specially, it only updates
the flags after a one is written to them. Since the interrupt for
frame errors is not enabled an old error can hence been seen when a
state interrupt arrives. For example if the device is not connected
to the CAN-bus the error warning interrupt will have HECC_CANES
indicating there is no ack. The error passive interrupt thereafter
will have HECC_CANES flagging that there is a warning level. And if
thereafter there is a message successfully send HECC_CANES points to
an error passive event, while in reality it became error warning
again. In summary, the state is not always reported correctly.
So handle the state changes and frame errors separately. The state
changes are now based on the interrupt flags and handled directly
when they occur. The reporting of the frame errors is still done as
before, as a side effect of another interrupt.
note: the hecc_clear_bit will do a read, modify, write. So it will
not only clear the bit, but also reset all other bits being set as
a side affect, hence it is replaced with only clearing the flags.
note: The HECC_CANMC_CCR is no longer cleared in the state change
interrupt, it is completely unrelated.
And use net_ratelimit to make checkpatch happy.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the rx FIFO overflows the ti_hecc would silently drop them since
the overwrite protection is enabled for all mailboxes. So disable it for
the lowest priority mailbox and return a proper error value when receive
message lost is set. Drop the message itself in that case, since it
might be partially updated.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Release the mailbox after reading it, so it can be reused a bit earlier.
Since "can: rx-offload: continue on error" all pending message bits are
cleared directly, so remove clearing them in ti_hecc.
Suggested-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The HECC_CANMIM is set in the xmit path and cleared in the interrupt.
Since this is done with a read, modify, write action the register might
end up with some more MIM enabled then intended, since it is not
protected. That doesn't matter at all, since the tx interrupt disables
the mailbox with HECC_CANME (while holding a spinlock). So lets just
always keep MIM set.
While at it, since the mailbox direction never changes, don't set it
every time a message is send, ti_hecc_reset() already sets them to tx.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the interface goes down, the CPK should no longer take an active
part in the CAN-bus communication, like sending acks and error frames.
So enable configuration mode in ti_hecc_stop, so the CPK is no longer
active.
When a transceiver switch is present the acks and errors don't make it
to the bus, but disabling the CPK then does prevent oddities, like
ti_hecc_reset() failing, since the CPK can become bus-off and starts
counting the 11 bit recessive bits, which seems to block the reset. It
can also cause invalid interrupts and disrupt the CAN-bus, since
transmission can be stopped in the middle of a message, by disabling the
tranceiver while the CPK is sending.
Since the CPK is disabled after normal power on, it is typically only
seen when the interface is restarted.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
can_rx_offload_queue_sorted() fails
The call to can_rx_offload_queue_sorted() may fail and return an error
(in the current implementation due to resource shortage). The passed skb
is consumed.
This patch adds incrementing of the appropriate error counters to let
the device statistics reflect that there's a problem.
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
If the hardware FIFO is empty can_rx_offload_offload_one() will return
NULL.
In case a CAN frame was read from the hardware,
can_rx_offload_offload_one() returns the skb containing it.
Without this patch can_rx_offload_irq_offload_fifo() bails out if no skb
returned, regardless of the reason.
Similar to can_rx_offload_irq_offload_timestamp() in case of a resource
shortage the whole FIFO should be discarded, to avoid an IRQ storm and
give the system some time to recover. However if the FIFO is empty the
loop can be left.
With this patch the loop is left in case of empty FIFO, but not on
errors.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In case of a resource shortage, i.e. the rx_offload queue will overflow
or a skb fails to be allocated (due to OOM),
can_rx_offload_offload_one() will call mailbox_read() to discard the
mailbox and return an ERR_PTR.
However can_rx_offload_irq_offload_timestamp() bails out in the error
case. In case of a resource shortage all mailboxes should be discarded,
to avoid an IRQ storm and give the system some time to recover.
Since can_rx_offload_irq_offload_timestamp() is typically called from a
while loop, all message will eventually be discarded. So let's continue
on error instead to discard them directly.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
error value in case of errors
Before this patch can_rx_offload_offload_one() returns a pointer to a
skb containing the read CAN frame or a NULL pointer.
However the meaning of the NULL pointer is ambiguous, it can either mean
the requested mailbox is empty or there was an error.
This patch fixes this situation by returning:
- pointer to skb on success
- NULL pointer if mailbox is empty
- ERR_PTR() in case of an error
All users of can_rx_offload_offload_one() have been adopted, no
functional change intended.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
queue overflow or OOM
If the rx-offload skb_queue is full or the skb allocation fails (due to OOM),
the mailbox contents is discarded.
This patch adds the incrementing of the rx_fifo_errors statistics counter.
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
beyond skb_queue_len_max
The skb_queue is a linked list, holding the skb to be processed in the
next NAPI call.
Without this patch, the queue length in can_rx_offload_offload_one() is
limited to skb_queue_len_max + 1. As the skb_queue is a linked list, no
array or other resources are accessed out-of-bound, however this
behaviour is counterintuitive.
This patch limits the rx-offload skb_queue length to skb_queue_len_max.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_tail() will not
queue the skb and return with an error.
This patch frees the skb in case of a full queue, which brings
can_rx_offload_queue_tail() in line with the
can_rx_offload_queue_sorted() function, which has been adjusted in the
previous patch.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the caller.
Fixes: d254586c3453 ("can: rx-offload: Add support for HW fifo based irq offloading")
Reported-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
skb mem leak
If the rx-offload skb_queue is full can_rx_offload_queue_sorted() will
not queue the skb and return with an error.
None of the callers of this function, issue a kfree_skb() to free the
not queued skb. This results in a memory leak.
This patch fixes the problem by freeing the skb in case of a full queue.
The return value is adjusted to -ENOBUFS to better reflect the actual
problem.
The device stats handling is left to the callers, as this function might
be used in both the rx and tx path.
Fixes: 55059f2b7f86 ("can: rx-offload: introduce can_rx_offload_get_echo_skb() and can_rx_offload_queue_sorted() functions")
Cc: linux-stable <stable@vger.kernel.org>
Cc: Martin Hundebøll <martin@geanix.com>
Reported-by: Martin Hundebøll <martin@geanix.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
AXI CANIP doesn't support tx fifo empty interrupt feature(TXFEMP),
update the flags filed in the driver for AXI CAN case accordingly.
Fixes: 3281b380ec9f ("can: xilinx_can: Fix flags field initialization for axi can and canps")
Reported-by: Anssi Hannula <anssi.hannula@bitwise.fi>
Signed-off-by: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While the state is updated when the error counters increase and
decrease, there is no event when the bus recovers and the error counters
decrease again. So add that event as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Acked-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Tested-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the CAN interface is closed it the hardwre is put in power down
mode, but does not reset the error counters / state. Reset the D_CAN on
open, so the reported state and the actual state match.
According to [1], the C_CAN module doesn't have the software reset.
[1] http://www.bosch-semiconductors.com/media/ip_modules/pdf_2/c_can_fd8/users_manual_c_can_fd8_r210_1.pdf
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When the status register is read without the status IRQ pending, the
chip may not raise the interrupt line for an upcoming status interrupt
and the driver may miss a status interrupt.
It is critical that the BUSOFF status interrupt is forwarded to the
higher layers, since no more interrupts will follow without
intervention.
Thanks to Wolfgang and Joe for bringing up the first idea.
Signed-off-by: Kurt Van Dijck <dev.kurt@vandijck-laurijssen.be>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Joe Burmeister <joe.burmeister@devtank.co.uk>
Fixes: fa39b54ccf28 ("can: c_can: Get rid of pointless interrupts")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
While the state changes are reported when the error counters increase
and decrease, there is no event when the bus recovers and the error
counters decrease again. So add those as well.
Change the state going downward to be ERROR_PASSIVE -> ERROR_WARNING ->
ERROR_ACTIVE instead of directly to ERROR_ACTIVE again.
Signed-off-by: Jeroen Hofstee <jhofstee@victronenergy.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Fix a small slab info leak due to a failure to clear the command buffer
at allocation.
The first 16 bytes of the command buffer are always sent to the device
in pcan_usb_send_cmd() even though only the first two may have been
initialised in case no argument payload is provided (e.g. when waiting
for a response).
Fixes: bb4785551f64 ("can: usb: PEAK-System Technik USB adapters driver core")
Cc: stable <stable@vger.kernel.org> # 3.4
Reported-by: syzbot+863724e7128e14b26732@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
When decoding a buffer received from PCAN-USB, the first timestamp read in
a packet is a 16-bit coded time base, and the next ones are an 8-bit
offset to this base, regardless of the type of packet read.
This patch corrects a potential loss of synchronization by using a
timestamp index read from the buffer, rather than an index of received
data packets, to determine on the sizeof the timestamp to be read from the
packet being decoded.
Signed-off-by: Stephane Grosjean <s.grosjean@peak-system.com>
Fixes: 46be265d3388 ("can: usb: PEAK-System Technik PCAN-USB specific part")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The ECC (memory error detection and correction) mechanism can be
activated or not, controlled by the ECCDIS bit in CAN_MECR. When
disabled, updates on indications and reporting registers are stopped.
So if want to disable ECC completely, had better assert ECCDIS bit, not
just mask the related interrupts.
Fixes: cdce844865be ("can: flexcan: add vf610 support for FlexCAN")
Signed-off-by: Joakim Zhang <qiangqing.zhang@nxp.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver was accessing its driver data after having freed it.
Fixes: 0024d8ad1639 ("can: usb_8dev: Add support for USB2CAN interface from 8 devices")
Cc: stable <stable@vger.kernel.org> # 3.9
Cc: Bernd Krumboeck <b.krumboeck@gmail.com>
Cc: Wolfgang Grandegger <wg@grandegger.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
The driver was accessing its driver data after having freed it.
Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
In gs_can_open() if usb_submit_urb() fails the allocated urb should be
released.
Fixes: d08e973a77d1 ("can: gs_usb: Added support for the GS_USB CAN devices")
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Navid Emamdoost <navid.emamdoost@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
of_node_put() needs to be called when the device node which is got
from of_get_child_by_name() finished using.
Fixes: 2290aefa2e90 ("can: dev: Add support for limiting configured bitrate")
Cc: Franklin S Cooper Jr <fcooper@ti.com>
Signed-off-by: Wen Yang <wenyang@linux.alibaba.com>
Cc: linux-stable <stable@vger.kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
Add zero copy AF_XDP support. This patch adds zero copy support for
Tx and Rx; code for zero copy is added to ice_xsk.h and ice_xsk.c.
For Tx, implement ndo_xsk_wakeup. As with other drivers, reuse
existing XDP Tx queues for this task, since XDP_REDIRECT guarantees
mutual exclusion between different NAPI contexts based on CPU ID. In
turn, a netdev can XDP_REDIRECT to another netdev with a different
NAPI context, since the operation is bound to a specific core and each
core has its own hardware ring.
For Rx, allocate frames as MEM_TYPE_ZERO_COPY on queues that AF_XDP is
enabled.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Co-developed-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Maciej Fijalkowski <maciej.fijalkowski@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In preparation of AF XDP, move functions that will be used both by skb and
zero-copy paths to a new file called ice_txrx_lib.c. This allows us to
avoid using ifdefs to control the staticness of said functions.
Move other functions (ice_rx_csum, ice_rx_hash and ice_ptype_to_htype)
called only by the moved ones to the new file as well.
Signed-off-by: Krzysztof Kazimierczak <krzysztof.kazimierczak@intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
This driver forgets to disable and unprepare clks when remove.
Add calls to clk_disable_unprepare to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Building with W=1 (cf.scripts/Makefile.extrawarn) outputs:
warning: variable ‘ret’ set but not used [-Wunused-but-set-variable]
Drop the unused 'ret' variable.
Signed-off-by: Christophe Roullier <christophe.roullier@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
IOC3 hardware needs a 16k aligned TX ring.
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set NETIF_F_HIGHDMA together with the NETIF_F_IP_CSUM flag instead of
letting the second assignment overwrite it. Probably doesn't matter
in practice as none of the systems an IOC3 is usually found in has
highmem to start with.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Thomas Bogendoerfer <tbogendoerfer@suse.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
