| Age | Commit message (Collapse) | Author |
|---|
|
The LPUART Status Register needs to be cleared when closing the uart
port to get a clean environment when reopening the uart.
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
UARTBAUD_RDMAE and UARTBAUD_TDMAE are enabled in lpuart32_startup(), but
lpuart32_shutdown() not disable them, only free the dma ring buffer and
release the dma channels, so here disable the Rx/Tx DMA first in
lpuart32_shutdown().
Fixes: 42b68768e51b ("serial: fsl_lpuart: DMA support for 32-bit variant")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For the lpuart driver, the Idle Line Interrupt Enable now is only needed
for the CPU mode, so enable the UARTCTRL_ILIE at the correct place, and
clear it when shutdown.
Also need to configure the suitable UARTCTRL_IDLECFG, now the value is
0x7, represent 128 idle characters will trigger the Idle Line Interrupt.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221125101953.18753-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Convert dmaengine_terminate_all() calls to synchronous and asynchronous
versions where appropriate.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221123023619.30173-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use pm_ptr() to remove the need to mark the pm functions as
__maybe_unused when the kernel is built without CONFIG_PM support.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-4-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add runtime pm support to manage the lpuart clock.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-3-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
LPUART supports both synchronous wakeup and asynchronous wakeup(wakeup
the system when the UART clocks are shut-off), the synchronous wakeup is
configured by UARTCTRL_RIE interrupt, and the asynchronous wakeup is
configured by UARTBAUD_RXEDGIE interrupt.
Add lpuart_uport_is_active() to determine if the uart port needs to get
into the suspend states, also add lpuart_suspend_noirq() and
lpuart_resume_noirq() to enable and disable the wakeup irq bits if the
uart port needs to be set as wakeup source.
When use lpuart with DMA mode, it still needs to switch to the cpu mode
in .suspend() that enable cpu interrupts RIE and RXEDGIE as wakeup
source, after system resume back, needs to setup DMA again, .resume()
will share the HW setup code with .startup(), so abstract the same code
to the api like lpuart32_hw_setup().
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221110113859.8485-2-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpuart_global_reset() shouldn't break the on-going transmit engine, need
to recover the on-going data transfer after reset.
This can help earlycon here, since commit 60f361722ad2 ("serial:
fsl_lpuart: Reset prior to registration") moved lpuart_global_reset()
before uart_add_one_port(), earlycon is writing during global reset,
as global reset will disable the TX and clear the baud rate register,
which caused the earlycon cannot work any more after reset, needs to
restore the baud rate and re-enable the transmitter to recover the
earlycon write.
Also move the lpuart_global_reset() down, then we can reuse the
lpuart32_tx_empty() without declaration.
Fixes: bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20221024085844.22786-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Take advantage of the new uart_xmit_advance() helper.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-17-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
uart_port_tx() is a new helper to send characters to the device. Use it
in these drivers.
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@microchip.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Link: https://lore.kernel.org/r/20221004104927.14361-3-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a UART port is newly registered, uart_configure_port() seeks to
deassert RS485 Transmit Enable by setting the RTS bit in port->mctrl.
However a number of UART drivers interpret a set RTS bit as *assertion*
instead of deassertion: Affected drivers include those using
serial8250_em485_config() (except 8250_bcm2835aux.c) and some using
mctrl_gpio (e.g. imx.c).
Since the interpretation of the RTS bit is driver-specific, it is not
suitable as a means to centrally deassert Transmit Enable in the serial
core. Instead, the serial core must call on drivers to deassert it in
their driver-specific way. One way to achieve that is to call
->rs485_config(). It implicitly deasserts Transmit Enable.
So amend uart_configure_port() and uart_resume_port() to invoke
uart_rs485_config(). That allows removing calls to uart_rs485_config()
from drivers' ->probe() hooks and declaring the function static.
Skip any invocation of ->set_mctrl() if RS485 is enabled. RS485 has no
hardware flow control, so the modem control lines are irrelevant and
need not be touched. When leaving RS485 mode, reset the modem control
lines to the state stored in port->mctrl. That way, UARTs which are
muxed between RS485 and RS232 transceivers drive the lines correctly
when switched to RS232. (serial8250_do_startup() historically raises
the OUT1 modem signal because otherwise interrupts are not signaled on
ancient PC UARTs, but I believe that no longer applies to modern,
RS485-capable UARTs and is thus safe to be skipped.)
imx.c modifies port->mctrl whenever Transmit Enable is asserted and
deasserted. Stop it from doing that so port->mctrl reflects the RS232
line state.
8250_omap.c deasserts Transmit Enable on ->runtime_resume() by calling
->set_mctrl(). Because that is now a no-op in RS485 mode, amend the
function to call serial8250_em485_stop_tx().
fsl_lpuart.c retrieves and applies the RS485 device tree properties
after registering the UART port. Because applying now happens on
registration in uart_configure_port(), move retrieval of the properties
ahead of uart_add_one_port().
Link: https://lore.kernel.org/all/20220329085050.311408-1-matthias.schiffer@ew.tq-group.com/
Link: https://lore.kernel.org/all/8f538a8903795f22f9acc94a9a31b03c9c4ccacb.camel@ginzinger.com/
Fixes: d3b3404df318 ("serial: Fix incorrect rs485 polarity on uart open")
Cc: stable@vger.kernel.org # v4.14+
Reported-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reported-by: Roosen Henri <Henri.Roosen@ginzinger.com>
Tested-by: Matthias Schiffer <matthias.schiffer@ew.tq-group.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/2de36eba3fbe11278d5002e4e501afe0ceaca039.1663863805.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty") into tty-next
We need the tty fixes and api additions in this branch.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset
for imx7ulp and imx8qxp"), certain i.MX UARTs are reset after they've
already been registered. Register state may thus be clobbered after
user space has begun to open and access the UART.
Avoid by performing the reset prior to registration.
Fixes: bd5305dcabbc ("tty: serial: fsl_lpuart: do software reset for imx7ulp and imx8qxp")
Cc: stable@vger.kernel.org # v5.15+
Cc: Fugang Duan <fugang.duan@nxp.com>
Cc: Sherry Sun <sherry.sun@nxp.com>
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/72fb646c1b0b11c989850c55f52f9ff343d1b2fa.1662884345.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
lpuart_dma_shutdown tears down lpuart dma, but lpuart_flush_buffer can
still occur which in turn tries to access dma apis if lpuart_dma_tx_use
flag is true. At this point since dma is torn down, these dma apis can
abort. Set lpuart_dma_tx_use and the corresponding rx flag
lpuart_dma_rx_use to false in lpuart_dma_shutdown so that dmas are not
accessed after they are relinquished.
Otherwise, when try to kill btattach, kernel may panic. This patch may
fix this issue.
root@imx8ulpevk:~# btattach -B /dev/ttyLP2 -S 115200
^C[ 90.182296] Internal error: synchronous external abort: 96000210 [#1] PREEMPT SMP
[ 90.189806] Modules linked in: moal(O) mlan(O)
[ 90.194258] CPU: 0 PID: 503 Comm: btattach Tainted: G O 5.15.32-06136-g34eecdf2f9e4 #37
[ 90.203554] Hardware name: NXP i.MX8ULP 9X9 EVK (DT)
[ 90.208513] pstate: 600000c5 (nZCv daIF -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
[ 90.215470] pc : fsl_edma3_disable_request+0x8/0x60
[ 90.220358] lr : fsl_edma3_terminate_all+0x34/0x20c
[ 90.225237] sp : ffff800013f0bac0
[ 90.228548] x29: ffff800013f0bac0 x28: 0000000000000001 x27: ffff000008404800
[ 90.235681] x26: ffff000008404960 x25: ffff000008404a08 x24: ffff000008404a00
[ 90.242813] x23: ffff000008404a60 x22: 0000000000000002 x21: 0000000000000000
[ 90.249946] x20: ffff800013f0baf8 x19: ffff00000559c800 x18: 0000000000000000
[ 90.257078] x17: 0000000000000000 x16: 0000000000000000 x15: 0000000000000000
[ 90.264211] x14: 0000000000000003 x13: 0000000000000000 x12: 0000000000000040
[ 90.271344] x11: ffff00000600c248 x10: ffff800013f0bb10 x9 : ffff000057bcb090
[ 90.278477] x8 : fffffc0000241a08 x7 : ffff00000534ee00 x6 : ffff000008404804
[ 90.285609] x5 : 0000000000000000 x4 : 0000000000000000 x3 : ffff0000055b3480
[ 90.292742] x2 : ffff8000135c0000 x1 : ffff00000534ee00 x0 : ffff00000559c800
[ 90.299876] Call trace:
[ 90.302321] fsl_edma3_disable_request+0x8/0x60
[ 90.306851] lpuart_flush_buffer+0x40/0x160
[ 90.311037] uart_flush_buffer+0x88/0x120
[ 90.315050] tty_driver_flush_buffer+0x20/0x30
[ 90.319496] hci_uart_flush+0x44/0x90
[ 90.323162] +0x34/0x12c
[ 90.327253] tty_ldisc_close+0x38/0x70
[ 90.331005] tty_ldisc_release+0xa8/0x190
[ 90.335018] tty_release_struct+0x24/0x8c
[ 90.339022] tty_release+0x3ec/0x4c0
[ 90.342593] __fput+0x70/0x234
[ 90.345652] ____fput+0x14/0x20
[ 90.348790] task_work_run+0x84/0x17c
[ 90.352455] do_exit+0x310/0x96c
[ 90.355688] do_group_exit+0x3c/0xa0
[ 90.359259] __arm64_sys_exit_group+0x1c/0x20
[ 90.363609] invoke_syscall+0x48/0x114
[ 90.367362] el0_svc_common.constprop.0+0xd4/0xfc
[ 90.372068] do_el0_svc+0x2c/0x94
[ 90.375379] el0_svc+0x28/0x80
[ 90.378438] el0t_64_sync_handler+0xa8/0x130
[ 90.382711] el0t_64_sync+0x1a0/0x1a4
[ 90.386376] Code: 17ffffda d503201f d503233f f9409802 (b9400041)
[ 90.392467] ---[ end trace 2f60524b4a43f1f6 ]---
[ 90.397073] note: btattach[503] exited with preempt_count 1
[ 90.402636] Fixing recursive fault but reboot is needed!
Fixes: 6250cc30c4c4 ("tty: serial: fsl_lpuart: Use scatter/gather DMA for Tx")
Reviewed-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Signed-off-by: Thara Gopinath <tgopinath@microsoft.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220920111703.1532-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
engine to complete
When the user initializes the uart port, and waits for the transmit
engine to complete in lpuart32_set_termios(), if the UART TX fifo has
dirty data and the UARTMODIR enable the flow control, the TX fifo may
never be empty. So here we should disable the flow control first to make
sure the transmit engin can complete.
Fixes: 380c966c093e ("tty: serial: fsl_lpuart: add 32-bit register interface support")
Cc: stable <stable@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220821101527.10066-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The setting of RS485 RTS polarity is inverse in the current driver.
When the property of 'rs485-rts-active-low' is enabled in the dts node,
the RTS signal should be LOW during sending. Otherwise, if there is no
such a property, the RTS should be HIGH during sending.
Fixes: 03895cf41d18 ("tty: serial: fsl_lpuart: Add support for RS-485")
Cc: stable <stable@kernel.org>
Signed-off-by: Nicolas Diaz <nicolas.diaz@nxp.com>
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220805144529.604856-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The number of bits can be calculated using tty_get_frame_size(), no
need for the driver to do it on its own. Change bits to unsigned and
baud too since we're touching the declarations line anyway (the
respective core functions are typed unsigned).
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220830084925.5608-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The double `as' is duplicated in the comment, remove one.
Signed-off-by: Jason Wang <wangborong@cdjrlc.com>
Link: https://lore.kernel.org/r/20220803104208.4127-1-wangborong@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART can't distinguish between a break signal and a framing error,
so need to count the break characters if there is a framing error and
received data is zero instead of the parity error.
Fixes: 5541a9bacfe5 ("serial: fsl_lpuart: handle break and make sysrq work")
Reviewed-by: Michael Walle <michael@walle.cc>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220725050115.12396-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART hardware doesn't zero out the parity bit on the received
characters. This behavior won't impact the use cases of CS8 because
the parity bit is the 9th bit which is not currently used by software.
But the parity bit for CS7 must be zeroed out by software in order to
get the correct raw data.
Signed-off-by: Shenwei Wang <shenwei.wang@nxp.com>
Link: https://lore.kernel.org/r/20220714185858.615373-1-shenwei.wang@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Embed rs485_supported to uart_port to allow serial core to tweak it as
needed.
Reviewed-by: Lino Sanfilippo <l.sanfilippo@kunbus.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220704094515.6831-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
To be able to alter ADDRB within ->rs485_config(), take termios_rwsem
before calling ->rs485_config() and pass termios.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Serial core handles serial_rs485 sanitization. Remove custom
sanitization from lpuart_config_rs485.
This change loses dev_err when SER_RS485_RX_DURING_TX is set due to
incorrect configuration. Other drivers do not do similar prinout for
full-duplex case and it should be done in serial core if it is
desirable to notify on this condition. Personally, I doesn't see it
important because the kernel gracefully downgrades to half-duplex.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-31-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add information on supported serial_rs485 features.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-16-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
A few serial drivers make a call to rs485_config() themselves (all
these seem to relate to init). Convert them all to use a common helper
which makes it easy to make adjustments on tasks related to it as
serial_rs485 struct sanitization is going to be added.
In pci_fintek_setup() (in 8250_pci.c), the rs485_config() call was made
with NULL, however, it can be changed to pass uart_port's rs485 struct.
No other callers should pass NULL into rs485_config() so the NULL check
can now be eliminated.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220606100433.13793-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
if (termios->c_cflag & CRTSCTS) guarantees that CRTSCTS is not ever set
in the else block so clearing it is unnecessary.
While at it, remove also one pair of extra parenthesis.
Reviewed-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220513082906.11096-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty fixes in here as well, as we need to revert one of them :(
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If an irq is pending when devm_request_irq() is called, the irq
handler will cause a NULL pointer access because initialisation
is not done yet.
Fixes: 9d7ee0e28da59 ("tty: serial: lpuart: avoid report NULL interrupt")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Indan Zupancic <Indan.Zupancic@mep-info.com>
Link: https://lore.kernel.org/r/20220505114750.45423-1-Indan.Zupancic@mep-info.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
No need to initialize the count variable in lpuart_copy_rx_to_tty(),
so let's remove it here.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220418021844.29591-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
and ida_simple_get
Now fsl_lpuart driver use both of_alias_get_id() and ida_simple_get() in
.probe(), which has the potential bug. For example, when remove the
lpuart7 alias in dts, of_alias_get_id() will return error, then call
ida_simple_get() to allocate the id 0 for lpuart7, this may confilct
with the lpuart4 which has alias 0.
aliases {
...
serial0 = &lpuart4;
serial1 = &lpuart5;
serial2 = &lpuart6;
serial3 = &lpuart7;
}
So remove the ida_simple_get() in .probe(), return an error directly
when calling of_alias_get_id() fails, which is consistent with other
uart drivers behavior.
Fixes: 3bc3206e1c0f ("serial: fsl_lpuart: Remove the alias node dependence")
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220321112211.8895-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In uart_set_rs485_config() the serial core already ensures that only one of
both options RTS on send or RTS after send is set. It also assigns the
passed serial_rs485 struct to the uart port.
So remove the check and the assignment from the drivers rs485_config()
function to avoid redundancy.
Signed-off-by: Lino Sanfilippo <LinoSanfilippo@gmx.de>
Link: https://lore.kernel.org/r/20220410104642.32195-9-LinoSanfilippo@gmx.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Added support for counting the tty buffer overruns in fsl_lpuart driver
like other uart drivers.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20220111085130.5817-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for i.MXRT1050's uart.
Cc: Giulio Benetti <giulio.benetti@benettiengineering.com>
Signed-off-by: Jesse Taube <Mr.Bossman075@gmail.com>
Link: https://lore.kernel.org/r/20211215220538.4180616-8-Mr.Bossman075@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial driver fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use wait_event_interruptible in lpuart_dma_shutdown isn't a reasonable
behavior, since it may cause the system hang here if the condition
!sport->dma_tx_in_progress never to be true in some corner case, such as
when enable the flow control, the dma tx request may never be completed
due to the peer's CTS setting when run .shutdown().
So here change to use wait_event_interruptible_timeout instead of
wait_event_interruptible, the tx dma will be forcibly terminated if the
tx dma request cannot be completed within 300ms.
Considering the worst tx dma case is to have a 4K bytes tx buffer, which
would require about 300ms to complete when the baudrate is 115200.
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20211203030441.22873-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Revert commit b4b844930f27 ("tty: serial: fsl_lpuart: drop earlycon entry
for i.MX8QXP"), because this breaks earlycon support on imx8qm/imx8qxp.
While it is true that for earlycon there is no difference between
i.MX8QXP and i.MX7ULP (for now at least), there are differences
regarding clocks and fixups for wakeup support. For that reason it was
deemed unacceptable to add the imx7ulp compatible to device tree in
order to get earlycon working again.
Reviewed-by: Peng Fan <peng.fan@nxp.com>
Signed-off-by: Alexander Stein <alexander.stein@ew.tq-group.com>
Link: https://lore.kernel.org/r/20211124073109.805088-1-alexander.stein@ew.tq-group.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Do software reset for communication port on imx7ulp and imx8qxp after
the port is registered if the UART controller support the feature.
Do partition reset with LPUART's power on, LPUART registers will
keep the previous status, like on i.MX8QXP platform, which is not
expected action, so need to set the RST bit of GLOBAL register to reset
all uart internal logic and registers.
Currently, only i.MX7ULP and i.MX8QXP LPUART controllers include
global register that support the software reset.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823091801.17447-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add two stop bits support.
User can run the command to enable two stop bits for test:
stty cstopb -F /dev/ttyLPx
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210823081733.31941-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Register offset needs to be applied on mapbase also.
dma_tx/rx_request use the physical address of UARTDATA.
Register offset is currently only applied to membase (the
corresponding virtual addr) but not on mapbase.
Fixes: 24b1e5f0e83c ("tty: serial: lpuart: add imx7ulp support")
Reviewed-by: Leonard Crestez <leonard.crestez@nxp.com>
Signed-off-by: Adriana Reus <adriana.reus@nxp.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Signed-off-by: Andy Duan <fugang.duan@nxp.com>
Link: https://lore.kernel.org/r/20210819021033.32606-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There have a corner case that tx DMA .callback() is coming after
.flush_buffer(), then .callback() should check dma_tx_in_progress
flag and return in directly.
Signed-off-by: Fugang Duan <fugang.duan@nxp.com>
Signed-off-by: Vipul Kumar <vipul_kumar@mentor.com>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210817100203.21300-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch e60c2991f18b make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.
Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.
Fixes: e60c2991f18b ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SYSRQ doesn't work with DMA. This is because there is no error
indication whether a symbol had a framing error or not. Actually,
this is not completely correct, there is a bit in the data register
which is set in this case, but we'd have to read change the DMA access
to 16 bit and we'd need to post process the data, thus make the DMA
pointless in the first place.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-10-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART can loop the RX and TX signal. Add support for it.
Please note, this was only tested on the 32 bit version of the LPUART.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-9-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The LPUART doesn't have the ability to control the RTS or CTS line
manually. Instead it will set it automatically when data is send or
handle it when data is received. Thus drop the wrong code in set_mctrl.
For the 32 bit version this was already done in the commit 2b30efe2e88a
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"). Keep
the 8-bit version in sync and remove it there, too.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-8-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The wrong code in set_mctrl() was already removed in commit 2b30efe2e88a
("tty: serial: lpuart: Remove unnecessary code from set_mctrl"), but the
code in get_mctrl() wasn't removed. It will not return the state of the
RTS or CTS line but whether automatic flow control is enabled, which is
wrong for the get_mctrl(). Thus remove it.
Fixes: 2b30efe2e88a ("tty: serial: lpuart: Remove unnecessary code from set_mctrl")
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-7-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Although there is already sysrq characters handling, a break condition
was never detected. Add support for it.
The LPUART can't distinguish between a framing error and a break
condition. We assume it is a break if the received data is all zero.
Signed-off-by: Michael Walle <michael@walle.cc>
Link: https://lore.kernel.org/r/20210512141255.18277-6-michael@walle.cc
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
