| Age | Commit message (Collapse) | Author |
|---|
|
In the sh-sci driver, serial ports are mapped to the sci_ports[] array,
with earlycon mapped at index zero.
The uart_add_one_port() function eventually calls __device_attach(),
which, in turn, calls pm_request_idle(). The identified code path is as
follows:
uart_add_one_port() ->
serial_ctrl_register_port() ->
serial_core_register_port() ->
serial_core_port_device_add() ->
serial_base_port_add() ->
device_add() ->
bus_probe_device() ->
device_initial_probe() ->
__device_attach() ->
// ...
if (dev->p->dead) {
// ...
} else if (dev->driver) {
// ...
} else {
// ...
pm_request_idle(dev);
// ...
}
The earlycon device clocks are enabled by the bootloader. However, the
pm_request_idle() call in __device_attach() disables the SCI port clocks
while earlycon is still active.
The earlycon write function, serial_console_write(), calls
sci_poll_put_char() via serial_console_putchar(). If the SCI port clocks
are disabled, writing to earlycon may sometimes cause the SR.TDFE bit to
remain unset indefinitely, causing the while loop in sci_poll_put_char()
to never exit. On single-core SoCs, this can result in the system being
blocked during boot when this issue occurs.
To resolve this, increment the runtime PM usage counter for the earlycon
SCI device before registering the UART port.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-6-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The early_console_setup() function initializes sci_ports[0].port with an
object of type struct uart_port obtained from the struct earlycon_device
passed as an argument to early_console_setup().
Later, during serial port probing, the serial port used as earlycon
(e.g., port A) might be remapped to a different position in the sci_ports[]
array, and a different serial port (e.g., port B) might be assigned to slot
0. For example:
sci_ports[0] = port B
sci_ports[X] = port A
In this scenario, the new port mapped at index zero (port B) retains the
data associated with the earlycon configuration. Consequently, after the
Linux boot process, any access to the serial port now mapped to
sci_ports[0] (port B) will block the original earlycon port (port A).
To address this, introduce an early_console_exit() function to clean up
sci_ports[0] when earlycon is exited.
To prevent the cleanup of sci_ports[0] while the serial device is still
being used by earlycon, introduce the struct sci_port::probing flag and
account for it in early_console_exit().
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-5-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
in use
In the sh-sci driver, sci_ports[0] is used by earlycon. If the earlycon is
still active when sci_probe() is called and the new serial port is supposed
to map to sci_ports[0], return -EBUSY to prevent breaking the earlycon.
This situation should occurs in debug scenarios, and users should be
aware of the potential conflict.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Relocate the runtime PM enable operation to sci_probe_single(). This change
prepares the codebase for upcoming fixes.
While at it, replace the existing logic with a direct call to
devm_pm_runtime_enable() and remove sci_cleanup_single(). The
devm_pm_runtime_enable() function automatically handles disabling runtime
PM during driver removal.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20250116182249.3828577-3-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The port_cfg object is used by serial_console_write(), which serves as
the write function for the earlycon device. Marking port_cfg as __initdata
causes it to be freed after kernel initialization, resulting in earlycon
becoming unavailable thereafter. Remove the __initdata macro from port_cfg
to resolve this issue.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Fixes: 0b0cced19ab15c9e ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Link: https://lore.kernel.org/r/20250116182249.3828577-2-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On the Renesas RZ/G3S, when doing suspend to RAM, the uart_suspend_port()
is called. The uart_suspend_port() calls 3 times the
struct uart_port::ops::tx_empty() before shutting down the port.
According to the documentation, the struct uart_port::ops::tx_empty()
API tests whether the transmitter FIFO and shifter for the port is
empty.
The Renesas RZ/G3S SCIFA IP reports the number of data units stored in the
transmit FIFO through the FDR (FIFO Data Count Register). The data units
in the FIFOs are written in the shift register and transmitted from there.
The TEND bit in the Serial Status Register reports if the data was
transmitted from the shift register.
In the previous code, in the tx_empty() API implemented by the sh-sci
driver, it is considered that the TX is empty if the hardware reports the
TEND bit set and the number of data units in the FIFO is zero.
According to the HW manual, the TEND bit has the following meaning:
0: Transmission is in the waiting state or in progress.
1: Transmission is completed.
It has been noticed that when opening the serial device w/o using it and
then switch to a power saving mode, the tx_empty() call in the
uart_port_suspend() function fails, leading to the "Unable to drain
transmitter" message being printed on the console. This is because the
TEND=0 if nothing has been transmitted and the FIFOs are empty. As the
TEND=0 has double meaning (waiting state, in progress) we can't
determined the scenario described above.
Add a software workaround for this. This sets a variable if any data has
been sent on the serial console (when using PIO) or if the DMA callback has
been called (meaning something has been transmitted). In the tx_empty()
API the status of the DMA transaction is also checked and if it is
completed or in progress the code falls back in checking the hardware
registers instead of relying on the software variable.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241125115856.513642-1-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Using memcpy() prevents the compiler from doing any checking on the
types of the passed pointer parameters. Copy the structure using struct
assignment instead, to increase type-safety.
No change in generated code on all relevant architectures
(arm/arm64/riscv/sh).
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/e097e5c11afe5bd4c01135779c9a40e707ef6374.1733243287.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 3791ea69a4858b81e0277f695ca40f5aae40f312.
It was reported to cause boot-time issues, so revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Fixes: 3791ea69a485 ("serial: sh-sci: Clean sci_ports[0] after at earlycon exit")
Cc: stable <stable@kernel.org>
Cc: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The early_console_setup() function initializes the sci_ports[0].port with
an object of type struct uart_port obtained from the object of type
struct earlycon_device received as argument by the early_console_setup().
It may happen that later, when the rest of the serial ports are probed,
the serial port that was used as earlycon (e.g., port A) to be mapped to a
different position in sci_ports[] and the slot 0 to be used by a different
serial port (e.g., port B), as follows:
sci_ports[0] = port A
sci_ports[X] = port B
In this case, the new port mapped at index zero will have associated data
that was used for earlycon.
In case this happens, after Linux boot, any access to the serial port that
maps on sci_ports[0] (port A) will block the serial port that was used as
earlycon (port B).
To fix this, add early_console_exit() that clean the sci_ports[0] at
earlycon exit time.
Fixes: 0b0cced19ab1 ("serial: sh-sci: Add CONFIG_SERIAL_EARLYCON support")
Cc: stable@vger.kernel.org
Signed-off-by: Claudiu Beznea <claudiu.beznea.uj@bp.renesas.com>
Link: https://lore.kernel.org/r/20241106120118.1719888-4-claudiu.beznea.uj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After commit 0edb555a65d1 ("platform: Make platform_driver::remove()
return void") .remove() is (again) the right callback to implement for
platform drivers.
Convert all platform drivers below drivers/tty/serial to use .remove(),
with the eventual goal to drop struct platform_driver::remove_new(). As
.remove() and .remove_new() have the same prototypes, conversion is done
by just changing the structure member name in the driver initializer.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@baylibre.com>
Link: https://lore.kernel.org/r/20241007205803.444994-7-u.kleine-koenig@baylibre.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add serial support for RZ/V2H(P) SoC with earlycon.
The SCIF interface in the Renesas RZ/V2H(P) is similar to that available
in the RZ/G2L (R9A07G044) SoC, with the following differences:
- RZ/V2H(P) SoC has three additional interrupts: one for Tx end/Rx ready
and two for Rx and Tx buffer full, all of which are edge-triggered.
- RZ/V2H(P) supports asynchronous mode, whereas RZ/G2L supports both
synchronous and asynchronous modes.
- There are differences in the configuration of certain registers such
as SCSMR, SCFCR, and SCSPTR between the two SoCs.
To handle these differences on RZ/V2H(P) SoC SCIx_RZV2H_SCIF_REGTYPE
is added.
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20240604170513.522631-6-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Avoid a superfluous unlock/lock-pair by simply moving the printout to
the end of bailing out.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-10-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The hrtimer for RXDMA timeout was unconditionally restarted in the RXDMA
complete handler ignoring the fact that setting up DMA may fail and PIO
is used instead. Explicitly stop the timer when DMA is completed and
only restart it when setting up DMA was successful. This makes the
intention of the timer much clearer, the driver easier to understand and
simplifies assumptions about the timer. The latter avoids race
conditions if these assumptions were not met or confused.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-9-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure everyone knows that calling this function needs protection.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-8-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The to-be-fixed commit removed locking when invalidating the DMA RX
descriptors on shutdown. It overlooked that there is still a rx_timer
running which may still access the protected data. So, re-add the
locking.
Reported-by: Dirk Behme <dirk.behme@de.bosch.com>
Closes: https://lore.kernel.org/r/ee6c9e16-9f29-450e-81da-4a8dceaa8fc7@de.bosch.com
Fixes: 2c4ee23530ff ("serial: sh-sci: Postpone DMA release when falling back to PIO")
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Link: https://lore.kernel.org/r/20240506114016.30498-7-wsa+renesas@sang-engineering.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Switch from struct circ_buf to proper kfifo. kfifo provides much better
API, esp. when wrap-around of the buffer needs to be taken into account.
Look at pl011_dma_tx_refill() or cpm_uart_tx_pump() changes for example.
Kfifo API can also fill in scatter-gather DMA structures, so it easier
for that use case too. Look at lpuart_dma_tx() for example. Note that
not all drivers can be converted to that (like atmel_serial), they
handle DMA specially.
Note that usb-serial uses kfifo for TX for ages.
omap needed a bit more care as it needs to put a char into FIFO to start
the DMA transfer when OMAP_DMA_TX_KICK is set. In that case, we have to
do kfifo_dma_out_prepare twice: once to find out the tx_size (to find
out if it is worths to do DMA at all -- size >= 4), the second time for
the actual transfer.
All traces of circ_buf are removed from serial_core.h (and its struct
uart_state).
Signed-off-by: Jiri Slaby (SUSE) <jirislaby@kernel.org>
Cc: Al Cooper <alcooperx@gmail.com>
Cc: Matthias Brugger <matthias.bgg@gmail.com>
Cc: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com>
Cc: Kumaravel Thiagarajan <kumaravel.thiagarajan@microchip.com>
Cc: Tharun Kumar P <tharunkumar.pasumarthi@microchip.com>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Richard Genoud <richard.genoud@gmail.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Claudiu Beznea <claudiu.beznea@tuxon.dev>
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: Maciej W. Rozycki <macro@orcam.me.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: Neil Armstrong <neil.armstrong@linaro.org>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Bjorn Andersson <andersson@kernel.org>
Cc: Konrad Dybcio <konrad.dybcio@linaro.org>
Cc: Pali Rohár <pali@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Nicholas Piggin <npiggin@gmail.com>
Cc: Christophe Leroy <christophe.leroy@csgroup.eu>
Cc: Aneesh Kumar K.V <aneesh.kumar@kernel.org>
Cc: Naveen N. Rao <naveen.n.rao@linux.ibm.com>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Cc: Alim Akhtar <alim.akhtar@samsung.com>
Cc: Laxman Dewangan <ldewangan@nvidia.com>
Cc: Thierry Reding <thierry.reding@gmail.com>
Cc: Jonathan Hunter <jonathanh@nvidia.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang@linux.alibaba.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Hammer Hsieh <hammerh0314@gmail.com>
Cc: Peter Korsgaard <jacmet@sunsite.dk>
Cc: Timur Tabi <timur@kernel.org>
Cc: Michal Simek <michal.simek@amd.com>
Cc: Sumit Semwal <sumit.semwal@linaro.org>
Cc: Christian König <christian.koenig@amd.com>
Link: https://lore.kernel.org/r/20240405060826.2521-13-jirislaby@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Unlike the 8250 serial driver complex, the sh-sci driver uses only a
single pair of functions to read and write serial port registers.
Hence there is no need to incur the overhead of calling them through
indirection, like the serial_port_{in,out}() wrappers do.
Replace all calls to these wrappers by direct calls to
sci_serial_{in,out}().
Remove the setup of the uart_port.serial_{in,out}() callbacks. After
removal of all calls to serial_port_{in,out}() in the sh-sci driver, the
only remaining user is uart_xchar_out(), which the sh-sci driver does
not use.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Acked-by: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: https://lore.kernel.org/r/51e79d601cb9d9d63822d3773d3cf05a96868612.1709548811.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
dma_request_slave_channel() is deprecated. dma_request_chan() should
be used directly instead.
Switch to the preferred function and update the error handling accordingly.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/d6773b9bd88dbbbea06bc6d5cd59aa117b1ee2ee.1700416841.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The .remove() callback for a platform driver returns an int which makes
many driver authors wrongly assume it's possible to do error handling by
returning an error code. However the value returned is ignored (apart
from emitting a warning) and this typically results in resource leaks.
To improve here there is a quest to make the remove callback return
void. In the first step of this quest all drivers are converted to
.remove_new(), which already returns void. Eventually after all drivers
are converted, .remove_new() will be renamed to .remove().
Trivially convert this driver from always returning zero in the remove
callback to the void returning variant.
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20231110152927.70601-39-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
When a serial port is used for kernel console output, then all
modifications to the UART registers which are done from other contexts,
e.g. getty, termios, are interference points for the kernel console.
So far this has been ignored and the printk output is based on the
principle of hope. The rework of the console infrastructure which aims to
support threaded and atomic consoles, requires to mark sections which
modify the UART registers as unsafe. This allows the atomic write function
to make informed decisions and eventually to restore operational state. It
also allows to prevent the regular UART code from modifying UART registers
while printk output is in progress.
All modifications of UART registers are guarded by the UART port lock,
which provides an obvious synchronization point with the console
infrastructure.
To avoid adding this functionality to all UART drivers, wrap the
spin_[un]lock*() invocations for uart_port::lock into helper functions
which just contain the spin_[un]lock*() invocations for now. In a
subsequent step these helpers will gain the console synchronization
mechanisms.
Converted with coccinelle. No functional change.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Link: https://lore.kernel.org/r/20230914183831.587273-61-john.ogness@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the serial/tty fixes in here as well for testing and future
development.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix sleeping in atomic context warning as reported by the Smatch static
checker tool by replacing disable_irq->disable_irq_nosync.
Reported by: Dan Carpenter <dan.carpenter@linaro.org>
Fixes: 8749061be196 ("tty: serial: sh-sci: Add RZ/G2L SCIFA DMA tx support")
Cc: stable@kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/20230704154818.406913-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The DT of_device.h and of_platform.h date back to the separate
of_platform_bus_type before it as merged into the regular platform bus.
As part of that merge prepping Arm DT support 13 years ago, they
"temporarily" include each other. They also include platform_device.h
and of.h. As a result, there's a pretty much random mix of those include
files used throughout the tree. In order to detangle these headers and
replace the implicit includes with struct declarations, users need to
explicitly include the correct includes.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> # for imx
Link: https://lore.kernel.org/r/20230724205440.767071-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need to set TE to "0" (i.e., disable serial transmission) to
get the expected behavior of the end of serial transmission.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-6-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode), it is mentioned
that, set the SCR.TIE bit to 0 and SCR.TEIE bit to 1, after the last
data to be transmitted are written to the TDR.
This will generate tx end interrupt and in the handler set SCR.TE and
SCR.TEIE to 0.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-5-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
As per the RZ/G2L users hardware manual (Rev.1.20 Sep, 2022), section
23.3.7 Serial Data Transmission (Asynchronous Mode) it is mentioned
that the TE (transmit enable) must be set after setting TIE (transmit
interrupt enable) or these 2 bits are set to 1 simultaneously by a
single instruction. So set these 2 bits in single instruction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-4-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA rx support for RZ/G2L alike SoCs by disabling RXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Apart from this, we must set FIFO trigger to 1 for the expected behavior
of the receive transmission.
While at it replace the parameter irq to s->irqs[SCIx_RXI_IRQ] in
disable_irq_nosync() to match enable_irq() in sci_dma_rx_reenable_irq().
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SCIFA IP on RZ/G2L SoC has the same signal for both interrupt
and DMA transfer request. Setting DMARS register for DMA transfer
makes the signal to work as a DMA transfer request signal and
subsequent interrupt requests to the interrupt controller
are masked. Similarly clearing DMARS register makes signal to work as
interrupt signal and subsequent interrupt requests to the interrupt
controller are unmasked.
Add SCIFA DMA tx support for RZ/G2L alike SoCs by disabling TXI line
interrupt and setting DMARS registers by DMA api for DMA transfer request.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230412145053.114847-2-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SCI IP on RZ/G2L alike SoCs do not need regshift compared to other SCI
IPs on the SH platform. Currently, it does regshift and configuring Rx
wrongly. Drop adding regshift for RZ/G2L alike SoCs.
Fixes: dfc80387aefb ("serial: sh-sci: Compute the regshift value for SCI ports")
Cc: stable@vger.kernel.org
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230321114753.75038-3-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The fourth interrupt on SCI port is transmit end interrupt compared to
the break interrupt on other port types. So, shuffle the interrupts to fix
the transmit end interrupt handler.
Fixes: e1d0be616186 ("sh-sci: Add h8300 SCI")
Cc: stable <stable@kernel.org>
Suggested-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230317150403.154094-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
direction
The direction field in the DMA config is deprecated. The sh-sci driver
sets {src,dst}_{addr,addr_width} based on the DMA direction and
it results in dmaengine_slave_config() failure as RZ DMAC driver
validates {src,dst}_addr_width values independent of DMA direction.
Fix this issue by passing both {src,dst}_{addr,addr_width}
values independent of DMA direction.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Link: https://lore.kernel.org/r/20230322074717.6057-1-biju.das.jz@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The driver can be compile tested with !CONFIG_OF making certain data
unused:
drivers/tty/serial/sh-sci.c:3144:34: error: ‘of_sci_match’ defined but not used [-Werror=unused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Link: https://lore.kernel.org/r/20230310222957.315848-1-krzysztof.kozlowski@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is preferred to use typed property access functions (i.e.
of_property_read_<type> functions) rather than low-level
of_get_property/of_find_property functions for reading properties. As
part of this, convert of_get_property/of_find_property calls to the
recently added of_property_present() helper when we just want to test
for presence of a property and nothing more.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230310144727.1545630-1-robh@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty/serial driver updates from Greg KH:
"Here is the "big" set of tty/serial driver changes for 6.2-rc1.
As in previous kernel releases, nothing big here at all, just some
small incremental serial/tty layer cleanups and some individual driver
additions and fixes. Highlights are:
- serial helper macros from Jiri Slaby to reduce the amount of
duplicated code in serial drivers
- api cleanups and consolidations from Ilpo Järvinen in lots of
serial drivers
- the usual set of n_gsm fixes from Daniel Starke as that code gets
exercised more
- TIOCSTI is finally able to be disabled if requested (security
hardening feature from Kees Cook)
- fsl_lpuart driver fixes and features added
- other small serial driver additions and fixes
All of these have been in linux-next for a while with no reported
problems"
* tag 'tty-6.2-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (97 commits)
serial: atmel: don't stop the transmitter when doing PIO
serial: atmel: cleanup atmel_start+stop_tx()
tty: serial: fsl_lpuart: switch to new dmaengine_terminate_* API
serial: sunsab: Fix error handling in sunsab_init()
serial: altera_uart: fix locking in polling mode
serial: pch: Fix PCI device refcount leak in pch_request_dma()
tty: serial: fsl_lpuart: Use pm_ptr() to avoid need to make pm __maybe_unused
tty: serial: fsl_lpuart: Add runtime pm support
tty: serial: fsl_lpuart: enable wakeup source for lpuart
serdev: Replace poll loop by readx_poll_timeout() macro
tty: synclink_gt: unwind actions in error path of net device open
serial: stm32: move dma_request_chan() before clk_prepare_enable()
dt-bindings: serial: xlnx,opb-uartlite: Drop 'contains' from 'xlnx,use-parity'
serial: pl011: Do not clear RX FIFO & RX interrupt in unthrottle.
serial: amba-pl011: avoid SBSA UART accessing DMACR register
tty: serial: altera_jtaguart: remove struct altera_jtaguart
tty: serial: altera_jtaguart: use uart_port::read_status_mask
tty: serial: altera_jtaguart: remove unused altera_jtaguart::sigs
tty: serial: altera_jtaguart: remove flag from altera_jtaguart_rx_chars()
n_tty: Rename tail to old_tail in n_tty_read()
...
|
|
When setting up the early console, the setup() callback of the
regular console is used. It is called manually before registering
the early console instead of providing a setup() callback for the
early console. This is probably because the early setup needs a
different @options during the early stage.
The issue here is that the setup() callback is called without the
console_list_lock held and functions such as uart_set_options()
expect that.
Rather than manually calling the setup() function before registering,
provide an early console setup() callback that will use the different
early options. This ensures that the error checking, ordering, and
locking context when setting up the early console are correct.
Since this early console can only be registered via the earlyprintk=
parameter, the @options argument of the setup() callback will always
be NULL. Rather than simply ignoring the argument, add a WARN_ON()
to get our attention in case the setup() callback semantics should
change in the future.
Note that technically the current implementation works because it is
only used in early boot. And since the early console setup is
performed before registering, it cannot race with anything and thus
does not need any locking. However, longterm maintenance is easier
when drivers rely on the subsystem API rather than manually
implementing steps that could cause breakage in the future.
Signed-off-by: John Ogness <john.ogness@linutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Petr Mladek <pmladek@suse.com>
Signed-off-by: Petr Mladek <pmladek@suse.com>
Link: https://lore.kernel.org/r/20221116162152.193147-41-john.ogness@linutronix.de
|
|
Take advantage of the new uart_xmit_advance() helper.
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20221019091151.6692-33-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There is no need to and tail with UART_XMIT_SIZE - 1 because tail is
already on valid range.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Testing also CIRC_CNT() with CIRC_CNT_TO_END() is unnecessary because
to latter alone covers all necessary cases.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220823141839.165244-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
There should be no reason to adjust old ktermios which is going to get
discarded anyway.
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Only CS7 and CS8 seem supported but CSIZE is not sanitized from
CS5 or CS6 to CS8.
Set CSIZE correctly so that userspace knows the effective value.
Incorrect CSIZE also results in miscalculation of the frame bits in
tty_get_char_size() or in its predecessor where the roughly the same
code is directly within uart_update_timeout().
Fixes: 1da177e4c3f4 (Linux-2.6.12-rc2)
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220519081808.3776-6-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Currently, uart_console_write->putchar's second parameter (the
character) is of type int. It makes little sense, provided uart_console_write()
accepts the input string as "const char *s" and passes its content -- the
characters -- to putchar(). So switch the character's type to unsigned
char.
We don't use char as that is signed on some platforms. That would cause
troubles for drivers which (implicitly) cast the char to u16 when
writing to the device. Sign extension would happen in that case and the
value written would be completely different to the provided char. DZ is
an example of such a driver -- on MIPS, it uses u16 for dz_out in
dz_console_putchar().
Note we do the char -> uchar conversion implicitly in
uart_console_write(). Provided we do not change size of the data type,
sign extension does not happen there, so the problem is void.
This makes the types consistent and unified with the rest of the uart
layer, which uses unsigned char in most places already. One exception is
xmit_buf, but that is going to be converted later.
Cc: Paul Cercueil <paul@crapouillou.net>
Cc: Tobias Klauser <tklauser@distanz.ch>
Cc: Russell King <linux@armlinux.org.uk>
Cc: Vineet Gupta <vgupta@kernel.org>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: bcm-kernel-feedback-list@broadcom.com
Cc: Alexander Shiyan <shc_work@mail.ru>
Cc: Baruch Siach <baruch@tkos.co.il>
Cc: "Maciej W. Rozycki" <macro@orcam.me.uk>
Cc: Paul Walmsley <paul.walmsley@sifive.com>
Cc: Palmer Dabbelt <palmer@dabbelt.com>
Cc: Albert Ou <aou@eecs.berkeley.edu>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Karol Gugala <kgugala@antmicro.com>
Cc: Mateusz Holenko <mholenko@antmicro.com>
Cc: Vladimir Zapolskiy <vz@mleia.com>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Kevin Hilman <khilman@baylibre.com>
Cc: Jerome Brunet <jbrunet@baylibre.com>
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Cc: Taichi Sugaya <sugaya.taichi@socionext.com>
Cc: Takao Orito <orito.takao@socionext.com>
Cc: Liviu Dudau <liviu.dudau@arm.com>
Cc: Sudeep Holla <sudeep.holla@arm.com>
Cc: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: "Andreas Färber" <afaerber@suse.de>
Cc: Manivannan Sadhasivam <mani@kernel.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Krzysztof Kozlowski <krzysztof.kozlowski@canonical.com>
Cc: Orson Zhai <orsonzhai@gmail.com>
Cc: Baolin Wang <baolin.wang7@gmail.com>
Cc: Chunyan Zhang <zhang.lyra@gmail.com>
Cc: Patrice Chotard <patrice.chotard@foss.st.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Peter Korsgaard <peter@korsgaard.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Acked-by: Richard Genoud <richard.genoud@gmail.com> [atmel_serial]
Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Acked-by: Paul Cercueil <paul@crapouillou.net>
Acked-by: Neil Armstrong <narmstrong@baylibre.com> # meson_serial
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20220303080831.21783-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
"a * (1 << b)" == "a << b".
No change in generated code.
Reviewed-by: Ulrich Hecht <uli+renesas@fpond.eu>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/118d62e167f6cf5e98bdf9a738634b4590ea8d09.1645460901.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Update the SCIF serial driver to remove printouts for break, frame, parity
and overrun errors. This reduces the amount of console printouts generated
by the defconfig kernel on R-Car Gen3 for certain use cases. To retrieve
more information about such errors the user may inspect counters. Also these
errors are fed into the TTY layer for further application specific handling.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Magnus Damm <damm+renesas@opensource.se>
Link: https://lore.kernel.org/r/163884254093.18109.2982470198301927679.sendpatchset@octo
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The sh-sci driver supports up to four input clocks, of which only the
first one is mandatory.
Replace devm_clk_get() and custom error checking by
devm_clk_get_optional(), to simplify the code and to catch all real
errors.
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/bce27288cb570952dd96b441e1af8768ad8b4870.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Use the dev_err_probe() helper to streamline error handling.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/5c4dd8df1f8d0d14786f26ee80b77f3eb8e06cd5.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Since commit 1b463bd51042927e ("ARM: dts: r8a7794: Rename the serial
port clock to fck") in v4.6, all upstream DTS files call the SCIF
functional clock "fck".
Hence the time is ripe to drop backward-compatibility with old DTBs that
use the old "sci_ick" name.
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/b4103e44d6ac46b6c1c264e2aeac80b39941fe74.1639663832.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add serial support for R-Car Gen4 SoC.
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20211209070817.1223888-3-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On RZ/G2L SoC we need to explicitly deassert the reset line
for the device to work, use this opportunity to deassert/assert
reset line in sh-sci driver.
This patch adds support to read the "resets" property (if available)
from DT and perform deassert/assert when required.
Also, propagate the error to the caller of sci_parse_dt() instead of
returning NULL in case of failure.
Reviewed-by: Biju Das <biju.das.jz@bp.renesas.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20211110232920.19198-4-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
