| Age | Commit message (Collapse) | Author |
|---|
|
Introduce an attribute "inquiry_string" to the lun.
In some environments, e. g. BIOS boot menus, the inquiry string
is the only information about devices presented to the user. The
default string depends on the "cdrom" bit of the first lun as
well as the kernel version and allows no further customization.
So without access to the client it is not obvious which gadget is
active at a given point and what any of the available luns might
contain.
If "inquiry_string" is ignored or set to the empty string, the
old behavior is preserved.
Signed-off-by: Philipp Gesang <philipp.gesang@intra2net.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Rockchip platform merely enable usb3 clocks and
populate its children. So we can use this generic
glue layer to support Rockchip dwc3.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add a quirk to clear the GUSB3PIPECTL.DELAYP1TRANS bit,
which specifies whether disable delay PHY power change
from P0 to P1/P2/P3 when link state changing from U0
to U1/U2/U3 respectively.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Support to configure the UTMI+ PHY with an 8- or 16-bit
interface via DT. The UTMI+ PHY interface is a hardware
capability, and it's platform dependent. Normally, the
PHYIF can be configured during coreconsultant.
But for some specific USB cores(e.g. rk3399 SoC DWC3),
the default PHYIF configuration value is false, so we
need to reconfigure it by software.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Add a quirk to clear the GUSB2PHYCFG.U2_FREECLK_EXISTS bit,
which specifies whether the USB2.0 PHY provides a free-running
PHY clock, which is active when the clock control input is active.
Signed-off-by: William Wu <william.wu@rock-chips.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
With composite gadget (ACM + NCM), USB3380 to host TCP transfer
speed dropped to 150 Mbit/s compared to 900 Mbit/s with NCM
gadget. Problem seems to be that net2280/USB3380 has only four
DMA channels and those DMA channels are allocated to first HW
endpoints. Endpoint match function was mapping endpoint names
directly, so NCM did not get DMA for bulk endpoints.
This patch changed match_ep to prefer DMA enabled hw endpoints
for bulk usb endpoints and PIO for interrupt usb endpoints.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
With SuperSpeed CDC NCM gadget, net2280 would get stuck in
'handle_ep_small' function. Triggering issue requires large
TCP transfer from host to USB3380.
Patch adds check for stuck condition and prevents hard lockup.
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Patch enables SuperSpeed for NCM gadget.
Tested with USB3380 and measured TCP throughput with two Intel PCs:
udc to host: 920 Mbit/s
host to udc: 550 Mbit/s
Signed-off-by: Jussi Kivilinna <jussi.kivilinna@haltian.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
alloc_ordered_workqueue replaces the deprecated
create_singlethread_workqueue.
There are multiple work items on the work queue, which require
ordering. Hence, an ordered workqueue has been used.
The workqueue "wq_otg" is not being used on a memory reclaim path.
Hence, WQ_MEM_RECLAIM has not been set.
Acked-by: John Youn <johnyoun@synopsys.com>
Signed-off-by: Bhaktipriya Shridhar <bhaktipriya96@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The assignment ret = ret is redundant and can be removed.
Reviewed-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Disabling USB gadget functions configured through configfs is something
that can happen in normal use cases. Keep the existing log for this type
of event, but only as information, not as an error.
Signed-off-by: Romain Izard <romain.izard.pro@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
As the last known user, ie. pxa27x_udc relying on calls to
usb_gadget_xxx() was amended to use the phy notifier, remove a bit the
USB stack adherence.
Actually the driver still uses the gadget API for structures definition,
but the implementation of USB gadget specific function usb_gadget_*() is
not necessary anymore.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In the gpio based case, the status of the phy is known at start by
reading the VBus gpio.
Actually, this is a fix, as this initial state, when not set up,
prevents a gadget to answer to the enumeration phase, as there is no
notification in this case (the VBus is already high when kernel boots)
so no interrupt is triggered, and the flow is :
- gadget initializes
- gadget gets its phy-generic with a xxx_get_phy_xxx() call type
- gadget does a "set_peripheral()" call type
=> here if the otg->state is correctly filled, the proper vbus
handling will be called, and the gadget will be aware it should
answer enumeration and go forth
Without this fix, the USB cable must be removed and replugged for any
gadget relying on phy-generic and its gpio vbus handling to work.
The problem was seen on a pxa27x architecture based board on a
devicetree build.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In the legacy behavior, and USB phy, upon detection a VBus signal, was
calling usb_gadget_vbus_(dis)connect().
This model doesn't work if the phy is generic and doesn't have an
adherence to the gadget API.
Instead of relying on the phy to call the gadget API, hook up the phy
notifier to report the VBus event, and upon it call the usb gadget API
ourselves.
This brings a new ordering problem, as before even if the usb_get_phy()
was failing because the UDC was probed before the phy, the phy would
call the gadget anyway, making the VBus connection event forwarded to
the gadget. Now we rely on the notifier, we have to ensure the
xxx_get_phy() does indeed work.
In order to cope with this, it is assumed that :
- for legacy platform_data machine, as the ordering cannot be ensured,
the phy must call usb_gadget_vbus_(dis)connect, such as
phy-gpio-vbus-usb.c
- for new devicetree platforms, we'll rely on the probe deferral, and
the phy can be gadget API agnostic.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
No functional changes, just a slight cosmetic
change.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We don't use LST bit anymore, so this condition will
never trigger.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Upon transfer completion after a full ring, let's
add more TRBs to our ring in order to complete our
request successfully.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
There was a typo when generating endpoint name which
would be very confusing when debugging. Fix it.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Always unmap all SG entries as required by DMA API
Fixes: a698908d3b3b ("usb: gadget: add generic map/unmap request utilities")
Cc: <stable@vger.kernel.org> # v3.4+
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
These product IDs are listed in Windows driver.
0x6803 corresponds to WeTelecom WM-D300.
0x6802 name is unknown.
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
UBSAN complains about a left shift by -1 in proc_do_submiturb(). This
can occur when an URB is submitted for a bulk or control endpoint on
a high-speed device, since the code doesn't bother to check the
endpoint type; normally only interrupt or isochronous endpoints have
a nonzero bInterval value.
Aside from the fact that the operation is illegal, it shouldn't matter
because the result isn't used. Still, in theory it could cause a
hardware exception or other problem, so we should work around it.
This patch avoids doing the left shift unless the shift amount is >= 0.
The same piece of code has another problem. When checking the device
speed (the exponential encoding for interrupt endpoints is used only
by high-speed or faster devices), we need to look for speed >=
USB_SPEED_SUPER as well as speed == USB_SPEED HIGH. The patch adds
this check.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Reported-by: Vittorio Zecca <zeccav@gmail.com>
Tested-by: Vittorio Zecca <zeccav@gmail.com>
Suggested-by: Bjørn Mork <bjorn@mork.no>
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The maximum value allowed for wMaxPacketSize of a high-speed interrupt
endpoint is 1024 bytes, not 1023.
Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Fixes: aed9d65ac327 ("USB: validate wMaxPacketValue entries in endpoint descriptors")
CC: <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove variables affected but never read.
Also drop the now unused TI_SET_SERIAL_FLAGS define.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: drop TI_SET_SERIAL_FLAGS ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Use C_X tty.h macros to avoid direct manipulation of termios
c_cflag variable.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
It is useless to check the return of usb_get_serial_port_data in the tty
and tty-port callbacks.
No need to check interface private data in close() either.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Remove useless or redundant dev_dbg messages.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: drop an unrelated change ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
__uX types should only be used for user-space interactions.
Also clean up uart-config endianess handling, and drop some redundant
casts.
Signed-off-by: Mathieu OTHACEHE <m.othacehe@gmail.com>
[ johan: amend commit message ]
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
If the ring is full and we are processing a big
sglist, then let's interrupt so we can, later, add
more TRBs to the ring.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
These two fields will be used in a follow-up patch
to track how many entries of request's sglist we
have already processed. The reason is that if a
gadget driver sends an sglist with more entries then
we can fit in the ring, we will have to continue
processing remaining afterwards.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We know that we have to iterate over the list of
started requests. Instead of looping forever, we can
rely on list_for_each_entry(). Likewise, instead of
a do {} while loop over all, maybe available,
scatterlist entries, we can detect if $this request
uses scatterlist and rely on for_each_sg().
This makes the code easier to follow while making
sure that we will *always* break out of the loop.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Many of the comments in that function are really
outdated and don't match what the driver is
doing. Moreover, recent patches combined programming
model for all non-control endpoints, this gives us
an opportunity to get rid of our special cases in
__dwc3_gadget_ep_queue().
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We always need to decrement our index by at least
one. Simplify the implementation by using a
temporary local variable and making sure that we
will always decrement one extra if tmp == 0.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Instead of waiting until giveback before
incrementing the dequeue pointer, we can increment
it from dwc3_cleanup_done_reqs(), that way we avoid
an extra loop over all TRBs during giveback.
While at that, also avoid using req->first_trb_index
as that's completely unnecessary. A follow-up patch
will clean up further uses of that and remove the
field altogether.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The only endpoint which actually requires LST bit
and XferComplete is ep0/1. Let's save some time by
completely removing LST bit support and
XferComplete.
This simplifies and consolidates endpoint handling
for all other 3 transfer types while also avoiding
extra interrupts.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
When usb gadget is set gadget serial function, it will be crash in below
situation.
It will clean the 'port->port_usb' pointer in gserial_disconnect() function
when usb link is inactive, but it will release lock for disabling the endpoints
in this function. Druing the lock release period, it maybe complete one request
to issue gs_write_complete()--->gs_start_tx() function, but the 'port->port_usb'
pointer had been set NULL, thus it will be crash in gs_start_tx() function.
This patch adds the 'port->port_usb' pointer checking in gs_start_tx() function
to avoid this situation.
Signed-off-by: Baolin Wang <baolin.wang@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
__dwc3_gadget_wakeup() is called while holding a spinlock, then depends on
jiffies in order to timeout while polling the USB core for a link state
update. In the case the wakeup failed, the timeout will never happen and
will also cause the cpu to stall until rcu_preempt kicks in.
This switches to a "decrement variable and wait" timeout scheme.
Signed-off-by: Nicolas Saenz Julienne <nicolassaenzj@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
We can't assign -EINVAL to a u16.
Fixes: 3948f0e0c999 ('usb: add Freescale QE/CPM USB peripheral controller driver')
Acked-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In eth_start_xmit, the socket buffer may be NULL. So, add NULL pointer
check at .wrap API.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
In case of error, the function usb_get_phy() returns ERR_PTR() and never
returns NULL. The NULL test in the return value check should be replaced
with IS_ERR().
Fixes: b5a2875605ca ("usb: renesas_usbhs: Allow an OTG PHY driver to
provide VBUS")
Cc: <stable@vger.kernel.org> # v4.3+
Acked-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Signed-off-by: Wei Yongjun <weiyj.lk@gmail.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Allow for platforms that have a reset controller driver in place to bring
the USB IP out of reset.
Signed-off-by: Dinh Nguyen <dinguyen@opensource.altera.com>
Acked-by: John Youn <johnyoun@synopsys.com>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
After going through runtime_suspend/runtime_resume
cycle once we would be left with an unbalanced
pm_runtime_get() call. Fix that by making sure that
we try to suspend right after resuming so things are
balanced and device can runtime_suspend again.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
During runtime_resume of dwc3-pci.c, we need to
runtime suspend our child device (which is dwc3
proper) otherwise nothing will happen.
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
The IS_ENABLED() macro checks if a Kconfig symbol has been enabled either
built-in or as a module, use that macro instead of open coding the same.
Using the macro makes the code more readable by helping abstract away some
of the Kconfig built-in and module enable details.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
We want the USB fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for WeTelecom WM-D200.
T: Bus=03 Lev=01 Prnt=01 Port=01 Cnt=01 Dev#= 4 Spd=12 MxCh= 0
D: Ver= 1.10 Cls=00(>ifc ) Sub=00 Prot=00 MxPS=64 #Cfgs= 1
P: Vendor=22de ProdID=6801 Rev=00.00
S: Manufacturer=WeTelecom Incorporated
S: Product=WeTelecom Mobile Products
C: #Ifs= 4 Cfg#= 1 Atr=80 MxPwr=500mA
I: If#= 0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 1 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 2 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
I: If#= 3 Alt= 0 #EPs= 2 Cls=08(stor.) Sub=06 Prot=50 Driver=usb-storage
Signed-off-by: Aleksandr Makarov <aleksandr.o.makarov@gmail.com>
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
When the controller is configured to be dual role and it's in host mode,
if bind udc and gadgt driver, those gadget operations will do gadget
disconnect and finally pull down DP line, which will break host function.
Cc: <stable@vger.kernel.org> # 4.1+
Signed-off-by: Li Jun <jun.li@nxp.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
Remove the hcd after checking for the xhci last quirks, not before.
This caused a hang on a Alpine Ridge xhci based maching which remove
the whole xhci controller when unplugging the last usb device
CC: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After a device is disconnected, xhci_stop_device() will be invoked
in xhci_bus_suspend().
Also the "disconnect" IRQ will have ISR to invoke
xhci_free_virt_device() in this sequence.
xhci_irq -> xhci_handle_event -> handle_cmd_completion ->
xhci_handle_cmd_disable_slot -> xhci_free_virt_device
If xhci->devs[slot_id] has been assigned to NULL in
xhci_free_virt_device(), then virt_dev->eps[i].ring in
xhci_stop_device() may point to an invlid address to cause kernel
panic.
virt_dev = xhci->devs[slot_id];
:
if (virt_dev->eps[i].ring && virt_dev->eps[i].ring->dequeue)
[] Unable to handle kernel paging request at virtual address 00001a68
[] pgd=ffffffc001430000
[] [00001a68] *pgd=000000013c807003, *pud=000000013c807003,
*pmd=000000013c808003, *pte=0000000000000000
[] Internal error: Oops: 96000006 [#1] PREEMPT SMP
[] CPU: 0 PID: 39 Comm: kworker/0:1 Tainted: G U
[] Workqueue: pm pm_runtime_work
[] task: ffffffc0bc0e0bc0 ti: ffffffc0bc0ec000 task.ti:
ffffffc0bc0ec000
[] PC is at xhci_stop_device.constprop.11+0xb4/0x1a4
This issue is found when running with realtek ethernet device
(0bda:8153).
Signed-off-by: Jim Lin <jilin@nvidia.com>
Cc: <stable@vger.kernel.org>
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Enqueue the first TRB even if full_len is zero.
Without this "adb install <apk>" freezes the system.
Signed-off-by: Alban Browaeys <alban.browaeys@gmail.com>
Fixes: 86065c2719a5 ("xhci: don't rely on precalculated value of needed trbs in the enqueue loop")
Signed-off-by: Mathias Nyman <mathias.nyman@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
