| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into clk-next
clk: tegra: Changes for v4.2-rc1
This contains the EMC clock driver that's been exhaustively reviewed and
tested. It also includes a change to the clock core that allows a clock
provider to perform low-level reparenting of clocks. This is required by
the EMC clock driver because the reparenting needs to be done at a very
specific point in time during the EMC frequency switch.
|
|
Folded into this merge commit is a build error fix: s/clk/core in
clk_change_rate due to the new struct clk_core
|
|
Exynos4210 based platforms have switched over to use generic
cpufreq driver for cpufreq functionality. So the Exynos
specific cpufreq support for these platforms can be removed.
Changes by Bartlomiej:
- dropped Exynos5250 support removal for now
- updated exynos-cpufreq.[c,h]
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
clock
With the addition of the new Samsung specific cpu-clock type, the
arm clock can be represented as a cpu-clock type. Add the CPU clock
configuration data and instantiate the CPU clock type for Exynos4210.
Changes by Bartlomiej:
- fixed issue with wrong dividers being setup by Common Clock Framework
(by an addition of CLK_RECALC_NEW_RATES clock flag to mout_apll clock,
without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board), this
was probably meant to be workarounded by use of CLK_GET_RATE_NOCACHE
and CLK_DIVIDER_READ_ONLY clock flags in the original patchset (in
"[PATCH v12 6/6] clk: samsung: remove unused clock aliases and update
clock flags") but using these flags is not sufficient to fix the issue
observed
- removed Exynos5250 and Exynos5420 support for now
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
The CPU clock provider supplies the clock to the CPU clock domain. The
composition and organization of the CPU clock provider could vary among
Exynos SoCs. A CPU clock provider can be composed of clock mux, dividers
and gates. This patch defines a new clock type for CPU clock provider and
adds infrastructure to register the CPU clock providers for Samsung
platforms.
Changes by Bartlomiej:
- fixed issue with setting lower dividers before the parent clock speed
was lowered (the issue resulted in lockup on Exynos4210 SoC based
Origen board when "ondemand" cpufreq governor was stress tested)
- fixed missing spin_unlock on error in exynos_cpuclk_post_rate_change()
problem by moving cfg_data search outside of the spin locked area
- removed leftover kfree() in exynos_register_cpu_clock() that could
result in dereferencing the NULL pointer on error
- moved spin_lock earlier in exynos_cpuclk_pre_rate_change() to cover
reading of E4210_SRC_CPU and E4210_DIV_CPU1 registers
- added missing "last chance" checks to wait_until_divider_stable() and
wait_until_mux_stable() (needed in case that IRQ handling took long
time to proceed and resulted in function printing incorrect error
message about timeout)
- moved E4210_CPU_DIV[0,1]() macros just before their only users,
this resulted in moving them from patch #2 to patch #3/6 ("clk:
samsung: exynos4: add cpu clock configuration data and instantiate
cpu clock")
- removed E5250_CPU_DIV[0,1](), E5420_EGL_DIV0() and E5420_KFC_DIV()
macros for now
- added my Copyrights to drivers/clk/samsung/clk-cpu.c
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Thomas Abraham <thomas.ab@samsung.com>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
This flag is needed to fix the issue with wrong dividers being setup
by Common Clock Framework when using the new Exynos cpu clock support.
The issue happens because clk_core_set_rate_nolock() calls
clk_calc_new_rates(clk, rate) before both pre/post clock notifiers have
a chance to run. In case of Exynos cpu clock support pre/post clock
notifiers are registered for mout_apll clock which is a parent of armclk
cpu clock and dividers are modified in both pre and post clock notifier.
This results in wrong dividers values being later programmed by
clk_change_rate(top). To workaround the problem CLK_RECALC_NEW_RATES
flag is added and it is set for mout_apll clock later so the correct
divider values are re-calculated after both pre and post clock notifiers
had run.
For example when using "performance" governor on Exynos4210 Origen board
the cpufreq-dt driver requests to change the frequency from 1000MHz to
1200MHz and after the change state of the relevant clocks is following:
Without use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 300000000
div_hpm rate: 300000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 300000000
div_pclk_dbg rate: 150000000
sclk_apll rate: 1200000000
sclk_apll_div_2 rate: 600000000
With use of CLK_GET_RATE_NOCACHE flag:
fout_apll rate: 1200000000
fout_apll_div_2 rate: 600000000
mout_clkout_cpu rate: 600000000
div_clkout_cpu rate: 600000000
clkout_cpu rate: 600000000
mout_apll rate: 1200000000
armclk rate: 1200000000
mout_hpm rate: 1200000000
div_copy rate: 200000000
div_hpm rate: 200000000
mout_core rate: 1200000000
div_core rate: 1200000000
div_core2 rate: 1200000000
arm_clk_div_2 rate: 600000000
div_corem0 rate: 300000000
div_corem1 rate: 150000000
div_periph rate: 300000000
div_atb rate: 240000000
div_pclk_dbg rate: 120000000
sclk_apll rate: 150000000
sclk_apll_div_2 rate: 75000000
Without this change cpufreq-dt driver showed ~10 mA larger energy
consumption when compared to cpufreq-exynos one when "performance"
cpufreq governor was used on Exynos4210 SoC based Origen board.
This issue was probably meant to be workarounded by use of
CLK_GET_RATE_NOCACHE and CLK_DIVIDER_READ_ONLY clock flags in
the original Exynos cpu clock patchset (in "[PATCH v12 6/6] clk:
samsung: remove unused clock aliases and update clock flags" patch)
but usage of these flags is not sufficient to fix the issue observed.
Cc: Thomas Abraham <thomas.ab@samsung.com>
Cc: Tomasz Figa <tomasz.figa@gmail.com>
Cc: Mike Turquette <mturquette@linaro.org>
Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Signed-off-by: Michael Turquette <mturquette@baylibre.com>
|
|
res variable was initialized to -ENOMEM, but it's override by
nvme_trans_copy_from_user(). So current code returns 0 if kcalloc fails.
Fix it to return proper error code.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Cisco has developed a new PCI HBA interface called sNIC, which stands for
SCSI NIC. This is a new storage feature supported on specialized network
adapter. The new PCI function provides a uniform host interface and abstracts
backend storage.
[jejb: fix up checkpatch errors]
Signed-off-by: Narsimhulu Musini <nmusini@cisco.com>
Signed-off-by: Sesidhar Baddela <sebaddel@cisco.com>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Signed-off-by: James Bottomley <JBottomley@Odin.com>
|
|
This fixes io submit ioctl handling when using extended metadata
formats. When these formats are used, the user provides a single virtually
contiguous buffer containing both the block and metadata interleaved,
so the metadata size needs to be added to the total length and not mapped
as a separate transfer.
The command is also driver generated, so this patch does not enforce
blk-integrity extensions provide the metadata buffer.
Reported-by: Marcin Dziegielewski <marcin.dziegielewski@intel.com>
Signed-off-by: Keith Busch <keith.busch@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
If the DryICE unit is locked it is impossible to set the time. Provide an
error message for this case.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Maybe the unit enters the hardware related state at runtime and not at
system boot time (after a power cycle).
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
This code is required to recover the unit from a security violation.
Hopefully this code can recover the unit from a hardware related invalid
state as well.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Document the i.MX DryIce machine states.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Robert Schwebel <rsc@pengutronix.de>
[rsc: got NDA clearance from Freescale]
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Be independent of the endianness of the kernel.
Signed-off-by: Juergen Borleis <jbe@pengutronix.de>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
There are now no differences between RTC on Exynos3250 and S3C6410.
Merge everything into one so duplicated code could be removed.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The rtc_timer_cancel() always returns 0 and cannot fail (calls only
other void-returning functions).
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The platform_device_id is not modified by the driver and core uses it as
const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
I'm no longer employed by HP.
Signed-off-by: dann frazier <dannf@dannf.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Michael Turquette:
"Very late clk regression fixes for the ARM-based AT91 platform.
These went unnoticed by me until recently, hence the late pull
request"
* tag 'clk-fixes-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
clk: at91: fix h32mx prototype inclusion in pmc header
clk: at91: trivial: typo in peripheral clock description
clk: at91: fix PERIPHERAL_MAX_SHIFT definition
clk: at91: pll: fix input range validity check
|
|
Fix CHANGE_LINK_STATE value when card_exist is true.
Fixes: a9b693cd77d7 ("Staging: rts5208: helper function to manage delink states")
Signed-off-by: Fabio Falzoi <fabio.falzoi84@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
gem_prime_map is not currently described in the DRM manual, lets document
it.
Signed-off-by: Daniel Thompson <daniel.thompson@linaro.org>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
This patch resolves the issue that refresh rate got low
at extension mode test with fimd and vidi combination.
The problem was because atomic_commit callback waited
for the completion of vblank to gaurantee crtc relevant
registers are updated from shadow registers to real ones.
However, the waiting there is really unnecessary because
page flip operation does already it.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The field 'vma' of 'exynos_drm_gem_obj' structure was introduced in
2a3098ff6c21 ("drm/exynos: add userptr feature for g2d module") but is
not referenced anywhere.
One instance of 'exynos_drm_gem_obj' may be mapped to multiple
user-space VMAs so 'vma' field does not look useful anyway.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch resolves page fault issue with iommu and atomic feature
when modetest test application is terminated.
ENWIN_F field of WINCONx register enables or disable a dma channel to
each hardware overlay - the value of the field will be updated to real
register after vsync.
So this patch makes sure the dma channel is disabled by waiting for vsync
one time after clearing shadow registers to all dma channels.
Below shows the page fault issue:
setting mode 720x1280-60Hz@XR24 on connectors 31, crtc 29
freq: 59.99Hz
[ 34.831025] PAGE FAULT occurred at 0x20400000 by 11e20000.sysmmu(Page
table base: 0x6e324000)
[ 34.838072] Lv1 entry: 0x6e92dc01
[ 34.841489] ------------[ cut here ]------------
[ 34.846058] kernel BUG at drivers/iommu/exynos-iommu.c:364!
[ 34.851614] Internal error: Oops - BUG: 0 [#1] PREEMPT SMP ARM
[ 34.857428] Modules linked in:
<--snip-->
[ 35.210894] [<c02880d0>] (exynos_sysmmu_irq) from [<c00608f8>]
(handle_irq_event_percpu+0x78/0x134)
[ 35.219914] [<c00608f8>] (handle_irq_event_percpu) from [<c00609f0>]
(handle_irq_event+0x3c/0x5c)
[ 35.228768] [<c00609f0>] (handle_irq_event) from [<c0063698>]
(handle_level_irq+0xc4/0x13c)
[ 35.237101] [<c0063698>] (handle_level_irq) from [<c005ff7c>]
(generic_handle_irq+0x2c/0x3c)
[ 35.245521] [<c005ff7c>] (generic_handle_irq) from [<c02214ec>]
(combiner_handle_cascade_irq+0x94/0x100)
[ 35.254980] [<c02214ec>] (combiner_handle_cascade_irq) from
[<c005ff7c>] (generic_handle_irq+0x2c/0x3c)
[ 35.264353] [<c005ff7c>] (generic_handle_irq) from [<c0060248>]
(__handle_domain_irq+0x7c/0xec)
[ 35.273034] [<c0060248>] (__handle_domain_irq) from [<c0009434>]
(gic_handle_irq+0x30/0x68)
[ 35.281366] [<c0009434>] (gic_handle_irq) from [<c0012ec0>]
(__irq_svc+0x40/0x74)
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
DRM Exynos driver is relying on dma-mapping internal structures when used
with IOMMU enabled. This patch partially hides dma-mapping internal things
by using proper get_dma_ops/set_dma_ops calls.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch adds code, which detach sub-device nodes from default iommu
domain if such has been configured. This lets Exynos DRM driver to properly
attach sub-devices to its own, common for all sub-devices domain.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
One should not do any assumptions on the stare of the fimd hardware
during driver initialization, so to properly reset fimd before enabling
IOMMU, one should ensure that all power domains and clocks are really
enabled. This patch adds pm_runtime and clocks management in the
fimd_clear_channel() function to ensure that any access to fimd
registers will be performed with clocks and power domains enabled.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
When the fimd is disabled by fimd_disable(), enabled overlay layers also
are disabled. If clocks for fimd are enabled by fimd_enable() on this
case, it can lead IOMMU page fault. The reason is that VIDCON0_ENVID and
VIDCON0_ENVID_F bits of VIDCON0 register are set still even though fimd
is disabled, so it may continue display output of prior when clocks for
fimd are enabled again.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
With atomic modesetting all the control for CRTC, Planes, Encoders and
Connectors should come from DRM core, so the driver is not allowed to
enable or disable planes from inside the crtc_enable()/disable() call.
But it needs to disable planes with crtc_disable in exynos driver
internally. Because crtc is disabled before plane is disabled, it means
plane_disable just returns without any register changes, then we cannot
be sure setting register to disable plane when crtc is disable.
This patch removes this chainned calls to enable plane from exynos hw
drivers code letting only DRM core touch planes except to disable plane.
Also it leads eliminable enabled and resume of struct exynos_drm_plane.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The reason waiting vblank is to be power gated and disabled clocks after
dma operation is completed. The dma operation is stopped already before
be power gated and clocks are disabled when mixer is disabled by commit
381be025ac1a6("drm/exynos: stop mixer before gating clocks during
poweroff"). Don't need to wait vblank anymore.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
FIMC & GSC driver can calculate the offset of planes. So there are
use cases which IPP receives just one GEM handle of an image with
multiple plane. This patch extends ipp_validate_mem_node() to validate
this case.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Config depends on the opreation. So it must be referenced by an
operation id, not a property id.
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
exynos_dsi_host_transfer() can be called through a panel driver while
DSI is turning down. It is possible because the function checks only
whether DSI is initialized or not, and there is a moment which DSI is
set by uninitialized, but DSI is still turning down. To prevent it,
DSI must be set by disabled before starting to be turned down, and
exynos_dsi_host_transfer() must check whether DSI is enabled or not.
Kernel dump:
[ 4721.351448] Unhandled fault: synchronous external abort (0x96000210) at 0xffffff800015e018
[ 4721.351809] Internal error: : 96000210 [#1] PREEMPT SMP
[ 4721.352031] Modules linked in:
[ 4721.352173] CPU: 2 PID: 300 Comm: deviced Tainted: G W 4.0.4-01017-g7964a87 #1
[ 4721.353989] Hardware name: Samsung DRACO board (DT)
[ 4721.358852] task: ffffffc0a0b70000 ti: ffffffc0a00ec000 task.ti: ffffffc0a00ec000
[ 4721.366327] PC is at exynos_dsi_enable_lane+0x14/0x5c
[ 4721.371353] LR is at exynos_dsi_host_transfer+0x834/0x8d8
[ 4721.376731] pc : [<ffffffc000432bcc>] lr : [<ffffffc000434590>] pstate: 60000145
[ 4721.384107] sp : ffffffc0a00efbe0
[ 4721.387405] x29: ffffffc0a00efbe0 x28: ffffffc0a00ec000
[ 4721.392699] x27: ffffffc000968000 x26: 0000000000000040
[ 4721.397994] x25: ffffffc000f74dc0 x24: ffffffc0a00efec8
[ 4721.403290] x23: ffffffc0a4815400 x22: ffffffc0009f2729
[ 4721.408584] x21: ffffffc0a00efcc8 x20: ffffffc0a4a2a848
[ 4721.413879] x19: ffffffc0a4a2a818 x18: 0000000000000004
[ 4721.419173] x17: 0000007faa5cddf0 x16: ffffffc0001a40a8
[ 4721.424469] x15: 0000000000000009 x14: 000000000000000d
[ 4721.429762] x13: 6e6e6f63206b726f x12: 0000000000000010
[ 4721.435058] x11: 0101010101010101 x10: 0000000000000000
[ 4721.440353] x9 : 000000000000000a x8 : 8386838282818381
[ 4721.445648] x7 : ffffffc0a201efe8 x6 : 0000000000000000
[ 4721.450943] x5 : 00000000fffffffa x4 : ffffffc0a201f170
[ 4721.456237] x3 : ffffff800015e000 x2 : ffffff800015e018
[ 4721.461531] x1 : 000000000000000f x0 : ffffffc0a4a2a818
[ 4721.466826]
[ 4721.468305] Process deviced (pid: 300, stack limit = 0xffffffc0a00ec028)
[ 4721.474989] Stack: (0xffffffc0a00efbe0 to 0xffffffc0a00f0000)
[ 4721.480720] fbe0: a00efca0 ffffffc0 0042c944 ffffffc0 a0f2d680 ffffffc0 00000024 00000000
[ 4721.488895] fc00: a4b6d000 ffffffc0 009f2729 ffffffc0 a4815400 ffffffc0 a00efec8 ffffffc0
Signed-off-by: Hyungwon Hwang <human.hwang@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
SoC checking code is not necessary anymore, as exynos_drm_match_add and
exynos_drm_platform_probe already properly handles situation when there are
no Exynos DRM components.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Tested-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
In case there are multiple pipelines and deferred probe occurs, only components
of the first pipeline were bound. As a result only one pipeline was available.
The main cause of this issue was dynamic generation of component match table -
every component driver during probe registered itself on helper list, if there
was at least one pipeline present on this list component match table were
created without deferred components.
This patch removes this helper list, instead it creates match table from
existing devices requiring exynos_drm KMS drivers. This way match table do not
depend on probe/deferral order and contains all KMS components.
As a side effect patch makes the code cleaner and significantly smaller.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Code registering different drivers and simple platform devices was dispersed
across multiple sub-modules. This patch moves it to one place. As a result
initialization code is shorter and cleaner and should simplify further
development.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Check error and call DRM_ERROR if clk_prepare_enable() fails.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This patch makes one of Linux framebuffer and DRM CRTC drivers
to be enabled.
Display controllers, FIMD and DECON, can be controlled by Linux
framebuffer or DRM CRTC drivers so only one of them should be
enabled.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
This patch removes unnsed varables in vidi_disable function.
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Reviewed-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
|
|
To follow more closely the new atomic API we split the dpms()
helper into the enable() and disable() helper to get exactly the
same semantics.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The planes are already disabled by the drm_atomic_helper_commit() code
so we don't need to disable the in these two places.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Run dpms operations through the atomic intefaces. This basically removes
the .dpms() callback from econders and crtcs and use .disable() and
.enable() to turn the crtc on and off.
v2: Address comments by Joonyoung:
- make hdmi code call ->disable() instead of ->dpms()
- do not use WARN_ON on crtc enable/disable
v3: - Fix build failure after the hdmi change in v2
- Change dpms helper of ptn3460 bridge
v4: - remove win_commit() call from .enable()
v5: - move .atomic_check() to the atomic PageFlip patch, and transform it
in .atomic_begin()
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
exynos needs to update planes with the crtc enabled (mainly for the FIMD
case) so this specific atomic commit changes the order of
drm_atomic_helper_commit_modeset_enables() and
drm_atomic_helper_commit_planes() to commit planes after we enable crtc
and encoders.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
This is a preparation commit to move exynos_drm_crtc_disable() together
with the future exynos_drm_crtc_enable() that will come from the split of
exynos_drm_crtc_dpms() callback.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Everything starts disabled so we don't really need to disable anything.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Now that no one is using the functions exported by exynos_drm_plane due
to the atomic conversion we can make remove some of the them or make them
static.
v2: remove unused exynos_drm_crtc
v3: fix checkpatch error (reported by Joonyoung)
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
PageFlips now use the atomic helper to work through the atomic modesetting
API. Async page flips are not supported yet.
v2: Add .atomic_begin() step to handle the vblank part we removed from
exynos page_flip code.
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Now that phase 1 and 2 are complete switch .set_config helper to
use the atomic one.
v2: also remove .prepare() callback
v3: remove .mode_set() and .mode_set_base() and encoder's
.prepare() callbacks
Signed-off-by: Gustavo Padovan <gustavo.padovan@collabora.co.uk>
Reviewed-by: Joonyoung Shim <jy0922.shim@samsung.com>
Tested-by: Tobias Jakobi <tjakobi@math.uni-bielefeld.de>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
