summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2022-09-26iommu/vt-d: Avoid unnecessary global IRTE cache invalidationLu Baolu
Some VT-d hardware implementations invalidate all interrupt remapping hardware translation caches as part of SIRTP flow. The VT-d spec adds a ESIRTPS (Enhanced Set Interrupt Remap Table Pointer Support, section 11.4.2 in VT-d spec) capability bit to indicate this. The spec also states in 11.4.4 that hardware also performs global invalidation on all interrupt remapping caches as part of Interrupt Remapping Disable operation if ESIRTPS capability bit is set. This checks the ESIRTPS capability bit and skip software global cache invalidation if it's set. Signed-off-by: Jacob Pan <jacob.jun.pan@linux.intel.com> Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Jerry Snitselaar <jsnitsel@redhat.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20220921065741.3572495-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/vt-d: Rename cap_5lp_support to cap_fl5lp_supportYi Liu
This renaming better describes it is for first level page table (a.k.a first stage page table since VT-d spec 3.4). Signed-off-by: Yi Liu <yi.l.liu@intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20220916071326.2223901-1-yi.l.liu@intel.com Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/vt-d: Remove pasid_set_eafe()Lu Baolu
It is not used anywhere in the tree. Remove it to avoid dead code. No functional change intended. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20220915081645.1834555-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/vt-d: Decouple PASID & PRI enabling from SVALu Baolu
Previously the PCI PASID and PRI capabilities are enabled in the path of iommu device probe only if INTEL_IOMMU_SVM is configured and the device supports ATS. As we've already decoupled the I/O page fault handler from SVA, we could also decouple PASID and PRI enabling from it to make room for growth of new features like kernel DMA with PASID, SIOV and nested translation. At the same time, the iommu_enable_dev_iotlb() helper is also called in iommu_dev_enable_feature(dev, IOMMU_DEV_FEAT_SVA) path. It's unnecessary and duplicate. This cleanups this helper to make the code neat. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20220915085814.2261409-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/vt-d: Remove unnecessary SVA data accesses in page fault pathLu Baolu
The existing I/O page fault handling code accesses the per-PASID SVA data structures. This is unnecessary and makes the fault handling code only suitable for SVA scenarios. This removes the SVA data accesses from the I/O page fault reporting and responding code, so that the fault handling code could be generic. Signed-off-by: Lu Baolu <baolu.lu@linux.intel.com> Reviewed-by: Kevin Tian <kevin.tian@intel.com> Link: https://lore.kernel.org/r/20220914011821.400986-1-baolu.lu@linux.intel.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26watchdog: booke_wdt: Replace PPC_FSL_BOOK3E by PPC_E500Christophe Leroy
CONFIG_PPC_FSL_BOOK3E is redundant with CONFIG_PPC_E500. Replace it so that CONFIG_PPC_FSL_BOOK3E can be removed later. Signed-off-by: Christophe Leroy <christophe.leroy@csgroup.eu> Acked-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: Michael Ellerman <mpe@ellerman.id.au> Link: https://lore.kernel.org/r/01a9132d51d3d8d9c74576d3da4d9d1fa5a88bde.1663606876.git.christophe.leroy@csgroup.eu
2022-09-26gpiolib: cdev: add fdinfo output for line request file descriptorsBartosz Golaszewski
Add fdinfo output for file descriptors created for user-space line requests in GPIO uAPI v2. The fdinfo file now contains the name of the GPIO chip that is the "parent" of the request as well as offsets of the lines requested. This allows user-space to parse the /proc/$PID/fdinfo entries and deduce the PID of the process that requested a specific line. Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl> Reviewed-by: Kent Gibson <warthog618@gmail.com>
2022-09-26iommu: dart: Support t6000 variantSven Peter
The M1 Pro/Max/Ultra SoCs come with a new variant of DART which supports a larger physical address space with a different PTE format. Pass through the correct paddr address space size and the PTE format to the io-pgtable code which will take care of the rest. Signed-off-by: Sven Peter <sven@svenpeter.dev> Co-developed-by: Janne Grunau <j@jannau.net> Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20220916094152.87137-6-j@jannau.net Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/io-pgtable-dart: Add DART PTE support for t6000Sven Peter
The DARTs present in the M1 Pro/Max/Ultra SoC use a diffent PTE format. They support a 42bit physical address space by shifting the paddr and extending its mask inside the PTE. They also come with mandatory sub-page protection now which we just configure to always allow access to the entire page. This feature is already present but optional on the previous DARTs which allows to unconditionally configure it. Signed-off-by: Sven Peter <sven@svenpeter.dev> Co-developed-by: Janne Grunau <j@jannau.net> Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20220916094152.87137-5-j@jannau.net Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/io-pgtable: Add DART subpage protection supportSven Peter
DART allows to only expose a subpage to the device. While this is an optional feature on the M1 DARTs the new ones present on the Pro/Max models require this field in every PTE. Signed-off-by: Sven Peter <sven@svenpeter.dev> Signed-off-by: Janne Grunau <j@jannau.net> Reviewed-by: Rob Herring <robh@kernel.org> Acked-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20220916094152.87137-4-j@jannau.net Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/io-pgtable: Move Apple DART support to its own fileJanne Grunau
The pte format used by the DARTs found in the Apple M1 (t8103) is not fully compatible with io-pgtable-arm. The 24 MSB are used for subpage protection (mapping only parts of page) and conflict with the address mask. In addition bit 1 is not available for tagging entries but disables subpage protection. Subpage protection could be useful to support a CPU granule of 4k with the fixed IOMMU page size of 16k. The DARTs found on Apple M1 Pro/Max/Ultra use another different pte format which is even less compatible. To support an output address size of 42 bit the address is shifted down by 4. Subpage protection is mandatory and bit 1 signifies uncached mappings used by the display controller. It would be advantageous to share code for all known Apple DART variants to support common features. The page table allocator for DARTs is less complex since it uses a two levels of translation table without support for huge pages. Signed-off-by: Janne Grunau <j@jannau.net> Acked-by: Robin Murphy <robin.murphy@arm.com> Acked-by: Sven Peter <sven@svenpeter.dev> Acked-by: Hector Martin <marcan@marcan.st> Link: https://lore.kernel.org/r/20220916094152.87137-3-j@jannau.net [ joro: Fix compile warning in __dart_alloc_pages()] Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/mediatek: Add support for MT6795 Helio X10 M4UsAngeloGioacchino Del Regno
Add support for the M4Us found in the MT6795 Helio X10 SoC. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Yong Wu <yong.wu@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20220913151148.412312-4-angelogioacchino.delregno@collabora.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/mediatek: Introduce new flag TF_PORT_TO_ADDR_MT8173AngeloGioacchino Del Regno
In preparation for adding support for MT6795, add a new flag named TF_PORT_TO_ADDR_MT8173 and use that instead of checking for m4u_plat type in mtk_iommu_hw_init() to avoid seeing a long list of m4u_plat checks there in the future. Signed-off-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Yong Wu <yong.wu@mediatek.com> Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com> Link: https://lore.kernel.org/r/20220913151148.412312-3-angelogioacchino.delregno@collabora.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/amd: Fix sparse warningVasant Hegde
CHECK drivers/iommu/amd/iommu.c drivers/iommu/amd/iommu.c:73:24: warning: symbol 'amd_iommu_ops' was not declared. Should it be static? Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20220912063248.7909-6-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/amd: Remove outdated commentVasant Hegde
Comment is not related to amd_iommu_ops variable. Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20220912063248.7909-5-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/amd: Free domain ID after domain_flush_pagesVasant Hegde
free_io_pgtable_ops() path uses domain ID to flush pages. Hence free domain ID after flushing everything. Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20220912063248.7909-4-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26iommu/amd: Free domain id in error pathVasant Hegde
Call domain_id_free() in error path. Signed-off-by: Vasant Hegde <vasant.hegde@amd.com> Link: https://lore.kernel.org/r/20220912063248.7909-2-vasant.hegde@amd.com Signed-off-by: Joerg Roedel <jroedel@suse.de>
2022-09-26pxa: Drop if with an always false conditionUwe Kleine-König
The remove callback is only called after probe completed successfully. In this case platform_set_drvdata() was called with a non-NULL argument and so ssp is never NULL. Also note that returning an error code from a remove callback doesn't result in the device staying bound. It's still removed and devm callbacks are called. So the memory that ssp pointed to during probe, goes away without the node being removed from ssp_list. The probable result of an early exit is accessing freed memory when the list is walked the next time. Signed-off-by: Uwe Kleine-König <(address hidden)> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2022-09-26drm/ttm: add dma_resv_assert_held() calls to vmap/vunmapChristian König
Let's make sure nobody is calling those functions without holding the appropriate locks. Signed-off-by: Christian König <christian.koenig@amd.com> Reviewed-by: Dmitry Osipenko <dmitry.osipenko@collabora.com> Link: https://patchwork.freedesktop.org/patch/msgid/20220715111533.467012-2-christian.koenig@amd.com
2022-09-26wifi: ath11k: Fix deadlock during WoWLAN suspendBaochen Qiang
We are seeing system hangs during WoWLAN suspend, and get below two stacks: Stack1: [ffffb02cc1557b20] __schedule at ffffffff8bb10860 [ffffb02cc1557ba8] schedule at ffffffff8bb10f24 [ffffb02cc1557bb8] schedule_timeout at ffffffff8bb16d88 [ffffb02cc1557c30] wait_for_completion at ffffffff8bb11778 [ffffb02cc1557c78] __flush_work at ffffffff8b0b30cd [ffffb02cc1557cf0] __cancel_work_timer at ffffffff8b0b33ad [ffffb02cc1557d60] ath11k_mac_drain_tx at ffffffffc0c1f0ca [ath11k] [ffffb02cc1557d70] ath11k_wow_op_suspend at ffffffffc0c5201e [ath11k] [ffffb02cc1557da8] __ieee80211_suspend at ffffffffc11e2bd3 [mac80211] [ffffb02cc1557dd8] wiphy_suspend at ffffffffc0f901ac [cfg80211] [ffffb02cc1557e08] dpm_run_callback at ffffffff8b75118a [ffffb02cc1557e38] __device_suspend at ffffffff8b751630 [ffffb02cc1557e70] async_suspend at ffffffff8b7519ea [ffffb02cc1557e88] async_run_entry_fn at ffffffff8b0bf4ce [ffffb02cc1557ea8] process_one_work at ffffffff8b0b1a24 [ffffb02cc1557ee0] worker_thread at ffffffff8b0b1c4a [ffffb02cc1557f18] kthread at ffffffff8b0b9cb8 [ffffb02cc1557f50] ret_from_fork at ffffffff8b001d32 Stack2: [ffffb02cc00b7d18] __schedule at ffffffff8bb10860 [ffffb02cc00b7da0] schedule at ffffffff8bb10f24 [ffffb02cc00b7db0] schedule_preempt_disabled at ffffffff8bb112b4 [ffffb02cc00b7db8] __mutex_lock at ffffffff8bb127ea [ffffb02cc00b7e38] ath11k_mgmt_over_wmi_tx_work at ffffffffc0c1aa44 [ath11k] [ffffb02cc00b7ea8] process_one_work at ffffffff8b0b1a24 [ffffb02cc00b7ee0] worker_thread at ffffffff8b0b1c4a [ffffb02cc00b7f18] kthread at ffffffff8b0b9cb8 [ffffb02cc00b7f50] ret_from_fork at ffffffff8b001d32 From the first stack, ath11k_mac_drain_tx calls cancel_work_sync(&ar->wmi_mgmt_tx_work) and waits all packets to be sent out or dropped. However, we find from Stack2 that this work item is blocked because ar->conf_mutex is already held by ath11k_wow_op_suspend. Fix this issue by moving ath11k_mac_wait_tx_complete to the start of ath11k_wow_op_suspend where ar->conf_mutex has not been acquired. And this change also makes the logic in ath11k_wow_op_suspend match the logic in ath11k_mac_op_start and ath11k_mac_op_stop. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220919021435.2459-1-quic_bqiang@quicinc.com
2022-09-26wifi: ath11k: Remove redundant ath11k_mac_drain_txBaochen Qiang
ath11k_mac_drain_tx is already called in ath11k_mac_wait_tx_complete, no need to call it again. So remove it. This is found in code review. Tested-on: WCN6855 hw2.0 PCI WLAN.HSP.1.1-03125-QCAHSPSWPL_V1_V2_SILICONZ_LITE-3 Signed-off-by: Baochen Qiang <quic_bqiang@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220919020259.1746-1-quic_bqiang@quicinc.com
2022-09-26wifi: ath11k: Add spectral scan support for 160 MHzTamizh Chelvam Raja
There are two types of 160 MHz spectral scan support mentioned below 1. Fragmented approach 2. Single event approach In this fragmented approach, single 160 MHz will be split as two 80 MHz buffer. First fft sample buffer will contain spectral scan result of primary 80 MHz and the second fft sample buffer will contain secondary 80 MHz and here cfreq1 and cfreq2 will be mentioned. In case of 160 MHz on 36th channel will contain cfreq1 as 5210 and cfreq2 as 5290. Chipsets which support this approach are IPQ8074/IPQ6018. Replacing freq1 with freq2 in every secondary sepctral scan event to distinguish between two different 80 MHz spectral event data. In the 2nd approach each fft sample buffer will contain spectral scan result for whole 160 MHz by mentioning cfreq1 as 5250 which is center frequency of whole 160 MHz. Chipset which support this approach is QCN9074. Host will receive spectral event from target for every 5 fft samples. Tested-on: IPQ8074 hw2.0 AHB WLAN.HK.2.5.0.1-01120-QCAHKSWPL-1 Tested-on: QCN9074 hw1.0 PCI WLAN.HK.2.5.0.1-01120-QCAHKSWP Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220725055001.15194-1-quic_tamizhr@quicinc.com
2022-09-26wifi: ath11k: Add support to get power save duration for each clientVenkateswara Naralasetty
Add support to get the following power save information through debugfs interface, * Current ps state of the peer * Time duration since the peer is in power save * Total duration of the peer spent in power save Above information is helpful in debugging the issues with power save clients. This patch also add trace log support for PS timekeeper to track the PS state change of the peers alongs with the peer MAC address and timestamp. Use the below commands to get the above power save information, To know the time_since_station_in_power_save: cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/ XX:XX:XX:XX:XX:XX/current_ps_duration To know power_save_duration: cat /sys/kernel/debug/ieee80211/phyX/netdev:wlanX/stations/ XX:XX:XX:XX:XX:XX/total_ps_duration To reset the power_save_duration of all stations connected to AP: echo 1 > /sys/kernel/debug/ieee80211/phyX/ath11k/reset_ps_duration To enable/disable the ps_timekeeper: echo Y > /sys/kernel/debug/ieee80211/phyX/ath11k/ps_timekeeper_enable Y = 1 to enable and Y = 0 to disable. To record PS timekeeer logs after enabling ps_timekeeper: trace-cmd record -e ath11k_ps_timekeeper Tested-on: Tested-on: IPQ8074 WLAN.HK.2.5.0.1-00991-QCAHKSWPL_SILICONZ-1 Signed-off-by: Venkateswara Naralasetty <quic_vnaralas@quicinc.com> Signed-off-by: Tamizh Chelvam Raja <quic_tamizhr@quicinc.com> Signed-off-by: Kalle Valo <quic_kvalo@quicinc.com> Link: https://lore.kernel.org/r/20220725054601.14719-1-quic_tamizhr@quicinc.com
2022-09-26media: flexcop-usb: use usb_endpoint_maxp()Johan Hovold
Use the usb_endpoint_maxp() helper instead of open coding. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220822151456.27178-4-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26media: flexcop-usb: clean up URB initialisationJohan Hovold
Clean up URB initialisation somewhat by introducing a temporary variable and separating declaration and non-trivial initialisation. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220822151456.27178-3-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26media: flexcop-usb: clean up endpoint sanity checksJohan Hovold
Add a temporary variable to make the endpoint sanity checks a bit more readable. While at it, fix a typo in the usb_set_interface() comment. Signed-off-by: Johan Hovold <johan@kernel.org> Link: https://lore.kernel.org/r/20220822151456.27178-2-johan@kernel.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26Merge 6.0-rc7 into usb-nextGreg Kroah-Hartman
We need the USB fixes in here for other follow-on changes to be able to be applied successfully. Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26cpufreq: qcom-cpufreq-hw: Add cpufreq qos for LMhXuewen Yan
Before update thermal pressure, the max cpufreq should be limited. Add QOS control for Lmh throttle cpufreq. Signed-off-by: Xuewen Yan <xuewen.yan@unisoc.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2022-09-26staging: r8188eu: don't check for stop/removal in the blink workerMartin Kaiser
The blink_work function calls either SwLedOff or SwLedOn. These two functions handle bSurpriseRemoved and bDriverStopped. There's no need to check bSurpriseRemoved and bDriverStopped again in the blink worker. Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20220925140406.112991-3-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: r8188eu: don't check bSurpriseRemoved in SwLedOffMartin Kaiser
The SwLedOff function calls rtw_read8 which in turn calls usb_read. bSurpriseRemoved is checked in usb_read. We don't have to check it again in SwLedOff. Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> # Edimax N150 Signed-off-by: Martin Kaiser <martin@kaiser.cx> Link: https://lore.kernel.org/r/20220925140406.112991-2-martin@kaiser.cx Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Remove unused variables ForcedAMSDUMaxSize, ...Philipp Hortmann
Remove unused variables that are may just once written but never read ForcedAMSDUMaxSize, PeerBandwidth, SwBwStep, bIsPeerBcm and bAcceptAddbaReq to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/0f3e63030511f72dbadc0368fd5e2dbd3ff84e07.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename CurrentMPDU..., ForcedAMPDU... and ForcedMPDU...Philipp Hortmann
Rename variable CurrentMPDUDensity to current_mpdu_density, ForcedAMPDUFactor to forced_ampdu_factor and ForcedMPDUDensity to forced_mpdu_density to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/4fb37ad6dab9addccf99a41a861220840c123e9b.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename SelfMimoPs, CurrentOpMode and bForcedShortGIPhilipp Hortmann
Rename variable SelfMimoPs to self_mimo_ps, CurrentOpMode to current_op_mode and bForcedShortGI to forced_short_gi to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/4c59f62a95b9a77711284998b98fbc559b8db813.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename PeerMimoPs, IOTAction and IOTRaFuncPhilipp Hortmann
Rename variable PeerMimoPs to peer_mimo_ps, IOTAction to iot_action and IOTRaFunc to iot_ra_func to avoid CamelCase which is not accepted by checkpatch. Added spaces around '&' as proposed by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/2a8ce7bff9a00fe44c057242cedb27ca91219137.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename RxRe...WinSize, RxReorder... and RxReorderDr...Philipp Hortmann
Rename variable RxReorderWinSize to rx_reorder_win_size, RxReorderPendingTime to rx_reorder_pending_time and RxReorderDropCounter to rx_reorder_drop_counter to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/e09ef6e2edc88e32782202589a9230204b547a9c.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename szRT2RTAggBuffer, bRegRxRe... and bCurRxReo...Philipp Hortmann
Rename variable szRT2RTAggBuffer to sz_rt2rt_agg_buf, bRegRxReorderEnable to reg_rx_reorder_enable and bCurRxReorderEnable to cur_rx_reorder_enable to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/af445e0a80dc8e153a1ba81df99309f19a69d6cb.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename bSwBwInPro..., bRegRT2RTAg... and bCurrentRT...Philipp Hortmann
Rename variable bSwBwInProgress to sw_bw_in_progress, bRegRT2RTAggregation to reg_rt2rt_aggregation and bCurrentRT2RTAggregation to current_rt2rt_aggregation to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/868f9db0e29bd170129f90bdbcc14238a750c440.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename dot11Cur..., bCurTxBW40MHz and bCurrentRT2...Philipp Hortmann
Rename variable dot11CurrentPreambleMode to dot11_current_preamble_mode, bCurTxBW40MHz to cur_tx_bw40mhz and bCurrentRT2RTLongSlotTime to current_rt2rt_long_slot_time to avoid CamelCase which is not accepted by checkpatch. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/97c4f62da9a98b0ddcdaafae68182e3eb47f9a17.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename eRfSleep, eRfPowerStateToSet and RfOffReasonPhilipp Hortmann
Rename variable eRfSleep to rf_sleep, eRfPowerStateToSet to rf_power_state_to_set and RfOffReason to rf_off_reason to avoid CamelCase which is not accepted by checkpatch. Omit the upfront "e" as no RfSleep and RfPowerStateToSet exist and it makes the variables unnecessary long. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/58e21e5cf86270edae93162db2395e6348c9c424.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename eRFPowerState, eRfOff and eRfOnPhilipp Hortmann
Rename variable eRFPowerState to rf_power_state, eRfOff to rf_off and eRfOn to rf_on to avoid CamelCase which is not accepted by checkpatch. Omit the upfront "e" as no RFPowerState, RfOff and RfOn exist and it makes the variables unnecessary long. Signed-off-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Link: https://lore.kernel.org/r/52c676bbaf1f894e30971c5c409b4bcb71c8ef7e.1664055213.git.philipp.g.hortmann@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: fwserial: delete the driver.Greg Kroah-Hartman
In the years since it was added (2012), no one has stepped up to maintain this properly and get it merged into the kernel tree. So remove it as it's obviously not being used. If it is being used, we can easily revert this and take the time to get it out of the staging tree. Link: https://lore.kernel.org/r/20220924105817.808385-1-gregkh@linuxfoundation.org Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: fix CamelCase variablesValentin Vidic
Fix checkpatch warnings for variables: LinkCtrlReg, DeviceID, RevisionID, IrqLine. Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Signed-off-by: Valentin Vidic <vvidic@valentin-vidic.from.hr> Link: https://lore.kernel.org/r/20220925123810.2492865-1-vvidic@valentin-vidic.from.hr Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26staging: rtl8192e: Rename Tx_Retry_Count_RegDragan Cvetic
Rename: Current_Tx_Rate_Reg to CURRENT_TX_RATE_REG, Initial_Tx_Rate_Reg to INITIAL_TX_RATE_REG and Tx_Retry_Count_Reg to TX_RETRY_COUNT_REG to avoid CamelCase which is not accepted by checkpatch.pl. Tested-by: Philipp Hortmann <philipp.g.hortmann@gmail.com> Signed-off-by: Dragan Cvetic <dragan.m.cvetic@gmail.com> Link: https://lore.kernel.org/r/20220924225126.10527-1-dragan.m.cvetic@gmail.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2022-09-26gpio: mvebu: Fix check for pwm support on non-A8K platformsPali Rohár
pwm support incompatible with Armada 80x0/70x0 API is not only in Armada 370, but also in Armada XP, 38x and 39x. So basically every non-A8K platform. Fix check for pwm support appropriately. Fixes: 85b7d8abfec7 ("gpio: mvebu: add pwm support for Armada 8K/7K") Signed-off-by: Pali Rohár <pali@kernel.org> Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
2022-09-26drm/ast: make ast_modeset staticruanjinjie
The symbol is not used outside of the file, so mark it static. Fixes the following warning: drivers/gpu/drm/ast/ast_drv.c:42:5: warning: symbol 'ast_modeset' was not declared. Should it be static? Signed-off-by: ruanjinjie <ruanjinjie@huawei.com> Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de> Link: https://patchwork.freedesktop.org/patch/msgid/20220926023253.739699-1-ruanjinjie@huawei.com
2022-09-26clk: mediatek: Use mtk_clk_register_gates_with_dev in simple probeYassine Oudjana
Register gates with dev in mtk_clk_simple_probe. Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Link: https://lore.kernel.org/r/20220813083319.45455-1-y.oudjana@protonmail.com Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
2022-09-26clk: mediatek: gate: Export mtk_clk_register_gates_with_devYassine Oudjana
This allows it to be used in drivers built as modules. Signed-off-by: Yassine Oudjana <y.oudjana@protonmail.com> Reviewed-by: Chen-Yu Tsai <wenst@chromium.org> Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@collabora.com> Reviewed-by: Markus Schneider-Pargmann <msp@baylibre.com> Link: https://lore.kernel.org/r/20220813083249.45427-1-y.oudjana@protonmail.com Signed-off-by: Chen-Yu Tsai <wenst@chromium.org>
2022-09-26Merge tag 'extcon-next-for-6.1' of ↵Greg Kroah-Hartman
git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon into char-misc-next Chanwoo writes: "Update extcon next for v6.1 1. Add USB Type-C support to extcon-tusb320.c - Add TYPE-C interface and expose the supported supply current, direction and connector polarity via the TYPE-C interface." * tag 'extcon-next-for-6.1' of git://git.kernel.org/pub/scm/linux/kernel/git/chanwoo/extcon: extcon: usbc-tusb320: fix kernel-doc warning extcon: usbc-tusb320: Add USB TYPE-C support extcon: usbc-tusb320: Factor out extcon into dedicated functions
2022-09-26cpufreq: Add __init annotation to module init funcsXiu Jianfeng
Add missing __init annotation to module init funcs. Signed-off-by: Xiu Jianfeng <xiujianfeng@huawei.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
2022-09-26cpufreq: tegra194: change tegra239_cpufreq_soc to staticYang Yingliang
tegra239_cpufreq_soc is only used in tegra194-cpufreq.c now, change it to static. Fixes: 676886010707 ("cpufreq: tegra194: Add support for Tegra239") Signed-off-by: Yang Yingliang <yangyingliang@huawei.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
generated by cgit (git 2.34.1) at 2025-09-19 05:34:56 +0000