| Age | Commit message (Collapse) | Author |
|---|
|
Fix use-after-free of skb when rx_handler returns RX_HANDLER_PASS.
Signed-off-by: Andreas Steinmetz <ast@domdv.de>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No reason to error out on a MT7621 device with DDR2 memory when non
TRGMII mode is selected.
Only MT7621 DDR2 clock setup is not supported for TRGMII mode.
But non TRGMII mode doesn't need any special clock setup.
Signed-off-by: René van Dorst <opensource@vdorst.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the CHAP_A value is not supported, the chap_server_open() function
should free the auth_protocol pointer and set it to NULL, or we will leave
a dangling pointer around.
[ 66.010905] Unsupported CHAP_A value
[ 66.011660] Security negotiation failed.
[ 66.012443] iSCSI Login negotiation failed.
[ 68.413924] general protection fault: 0000 [#1] SMP PTI
[ 68.414962] CPU: 0 PID: 1562 Comm: targetcli Kdump: loaded Not tainted 4.18.0-80.el8.x86_64 #1
[ 68.416589] Hardware name: Red Hat KVM, BIOS 0.5.1 01/01/2011
[ 68.417677] RIP: 0010:__kmalloc_track_caller+0xc2/0x210
Signed-off-by: Maurizio Lombardi <mlombard@redhat.com>
Reviewed-by: Chris Leech <cleech@redhat.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
WRITE SAME corrupts data on the block device behind iblock if the command
is emulated. The emulation code issues (M - 1) * N times more bios than
requested, where M is the number of 512 blocks per real block size and N is
the NUMBER OF LOGICAL BLOCKS specified in WRITE SAME command. So, for a
device with 4k blocks, 7 * N more LBAs gets written after the requested
range.
The issue happens because the number of 512 byte sectors to be written is
decreased one by one while the real bios are typically from 1 to 8 512 byte
sectors per bio.
Fixes: c66ac9db8d4a ("[SCSI] target: Add LIO target core v4.0.0-rc6")
Cc: <stable@vger.kernel.org>
Signed-off-by: Roman Bolshakov <r.bolshakov@yadro.com>
Reviewed-by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
I ran into an intriguing bug caused by
commit ""spi: gpio: Don't request CS GPIO in DT use-case"
affecting all SPI GPIO devices with an active high
chip select line.
The commit switches the CS gpio handling over to the GPIO
core, which will parse and handle "cs-gpios" from the OF
node without even calling down to the driver to get the
job done.
However the GPIO core handles the standard bindings in
Documentation/devicetree/bindings/spi/spi-controller.yaml
that specifies that active high CS needs to be specified
using "spi-cs-high" in the DT node.
The code in drivers/spi/spi-gpio.c never respected this
and never tried to inspect subnodes to see if they contained
"spi-cs-high" like the gpiolib OF quirks does. Instead the
only way to get an active high CS was to tag it in the
device tree using the flags cell such as
cs-gpios = <&gpio 4 GPIO_ACTIVE_HIGH>;
This alters the quirks to not inspect the subnodes of SPI
masters on "spi-gpio" for the standard attribute "spi-cs-high",
making old device trees work as expected.
This semantic is a bit ambigous, but just allowing the
flags on the GPIO descriptor to modify polarity is what
the kernel at large mostly uses so let's encourage that.
Fixes: 249e2632dcd0 ("spi: gpio: Don't request CS GPIO in DT use-case")
Cc: Andrey Smirnov <andrew.smirnov@gmail.com>
Cc: linux-gpio@vger.kernel.org
Cc: linux-spi@vger.kernel.org
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The variable r is being initialized with a value that is never
read and it is being updated later with a new value. The
initialization is redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes standard netdev stats in ethtool -S.
Suggested-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Signed-off-by: Xue Chaojing <xuechaojing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We support many speeds and it doesn't make much sense to list them all
in the Kconfig. Let's just call it Multi-Gigabit.
Suggested-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Jose Abreu <joabreu@synopsys.com>
Cc: Joao Pinto <jpinto@synopsys.com>
Cc: David S. Miller <davem@davemloft.net>
Cc: Giuseppe Cavallaro <peppe.cavallaro@st.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When compiling a kernel without support for CMA, CONFIG_CMA_ALIGNMENT
is not defined which results in the following build failure:
In file included from ./include/linux/list.h:9:0
from ./include/linux/kobject.h:19,
from ./include/linux/of.h:17
from ./include/linux/irqdomain.h:35,
from ./include/linux/acpi.h:13,
from drivers/iommu/arm-smmu-v3.c:12:
drivers/iommu/arm-smmu-v3.c: In function ‘arm_smmu_device_hw_probe’:
drivers/iommu/arm-smmu-v3.c:194:40: error: ‘CONFIG_CMA_ALIGNMENT’ undeclared (first use in this function)
#define Q_MAX_SZ_SHIFT (PAGE_SHIFT + CONFIG_CMA_ALIGNMENT)
Fix the breakage by capping the maximum queue size based on MAX_ORDER
when CMA is not enabled.
Reported-by: Zhangshaokun <zhangshaokun@hisilicon.com>
Signed-off-by: Will Deacon <will@kernel.org>
Tested-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
We register a AP PQAP instruction hook during the open
of the mediated device. And unregister it on release.
During the probe of the AP device, we allocate a vfio_ap_queue
structure to keep track of the information we need for the
PQAP/AQIC instruction interception.
In the AP PQAP instruction hook, if we receive a demand to
enable IRQs,
- we retrieve the vfio_ap_queue based on the APQN we receive
in REG1,
- we retrieve the page of the guest address, (NIB), from
register REG2
- we retrieve the mediated device to use the VFIO pinning
infrastructure to pin the page of the guest address,
- we retrieve the pointer to KVM to register the guest ISC
and retrieve the host ISC
- finaly we activate GISA
If we receive a demand to disable IRQs,
- we deactivate GISA
- unregister from the GIB
- unpin the NIB
When removing the AP device from the driver the device is
reseted and this process unregisters the GISA from the GIB,
and unpins the NIB address then we free the vfio_ap_queue
structure.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Acked-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
To be able to use the VFIO interface to facilitate the
mediated device memory pinning/unpinning we need to register
a notifier for IOMMU.
While we will start to pin one guest page for the interrupt indicator
byte, this is still ok with ballooning as this page will never be
used by the guest virtio-balloon driver.
So the pinned page will never be freed. And even a broken guest does
so, that would not impact the host as the original page is still
in control by vfio.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
We prepare the interception of the PQAP/AQIC instruction for
the case the AQIC facility is enabled in the guest.
First of all we do not want to change existing behavior when
intercepting AP instructions without the SIE allowing the guest
to use AP instructions.
In this patch we only handle the AQIC interception allowed by
facility 65 which will be enabled when the complete interception
infrastructure will be present.
We add a callback inside the KVM arch structure for s390 for
a VFIO driver to handle a specific response to the PQAP
instruction with the AQIC command and only this command.
But we want to be able to return a correct answer to the guest
even there is no VFIO AP driver in the kernel.
Therefor, we inject the correct exceptions from inside KVM for the
case the callback is not initialized, which happens when the vfio_ap
driver is not loaded.
We do consider the responsibility of the driver to always initialize
the PQAP callback if it defines queues by initializing the CRYCB for
a guest.
If the callback has been setup we call it.
If not we setup an answer considering that no queue is available
for the guest when no callback has been setup.
Signed-off-by: Pierre Morel <pmorel@linux.ibm.com>
Reviewed-by: Tony Krowiak <akrowiak@linux.ibm.com>
Acked-by: Harald Freudenberger <freude@linux.ibm.com>
Acked-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Halil Pasic <pasic@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Current code sets the dsci to 0x00000080. Which doesn't make any sense,
as the indicator area is located in the _left-most_ byte.
Worse: if the dsci is the _shared_ indicator, this potentially clears
the indication of activity for a _different_ device.
tiqdio_thinint_handler() will then have no reason to call that device's
IRQ handler, and the device ends up stalling.
Fixes: d0c9d4a89fff ("[S390] qdio: set correct bit in dsci")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When tiqdio_remove_input_queues() removes a queue from the tiq_list as
part of qdio_shutdown(), it doesn't re-initialize the queue's list entry
and the prev/next pointers go stale.
If a subsequent qdio_establish() fails while sending the ESTABLISH cmd,
it calls qdio_shutdown() again in QDIO_IRQ_STATE_ERR state and
tiqdio_remove_input_queues() will attempt to remove the queue entry a
second time. This dereferences the stale pointers, and bad things ensue.
Fix this by re-initializing the list entry after removing it from the
list.
For good practice also initialize the list entry when the queue is first
allocated, and remove the quirky checks that papered over this omission.
Note that prior to
commit e521813468f7 ("s390/qdio: fix access to uninitialized qdio_q fields"),
these checks were bogus anyway.
setup_queues_misc() clears the whole queue struct, and thus needs to
re-init the prev/next pointers as well.
Fixes: 779e6e1c724d ("[S390] qdio: new qdio driver.")
Cc: <stable@vger.kernel.org>
Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
The "len" variable is the length of the option up to the next option or
to the end of the string which ever first. We want to print the invalid
option so we want precision "%.*s" but the format is width "%*s" so it
prints up to the end of the string.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Tested-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Stefan Haberland <sth@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
Sometimes, we want to control which of the matching drivers
binds to a subchannel device (e.g. for subchannels we want to
handle via vfio-ccw).
For pci devices, a mechanism to do so has been introduced in
782a985d7af2 ("PCI: Introduce new device binding path using
pci_dev.driver_override"). It makes sense to introduce the
driver_override attribute for subchannel devices as well, so
that we can easily extend the 'driverctl' tool (which makes
use of the driver_override attribute for pci).
Note that unlike pci we still require a driver override to
match the subchannel type; matching more than one subchannel
type is probably not useful anyway.
Signed-off-by: Cornelia Huck <cohuck@redhat.com>
Reviewed-by: Halil Pasic <pasic@linux.ibm.com>
Reviewed-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Sebastian Ott <sebott@linux.ibm.com>
Signed-off-by: Vasily Gorbik <gor@linux.ibm.com>
|
|
When waking up from the Suspend-to-RAM state, the following error
was seen:
m25p80 spi2.0: flash operation timed out
The flash remained in an undefined state, returning 0xFFs.
Fix it by setting the Serial Clock Baud Rate, as it was set
before the conversion to SPIMEM.
Tested with sama5d2_xplained and mx25l25673g spi-nor in
Backup + Self-Refresh and Suspend modes.
Fixes: 0e6aae08e9ae ("spi: Add QuadSPI driver for Atmel SAMA5D2")
Reported-by: Mark Deneen <mdeneen@gmail.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Despite what I think the prm recommends, commit f2253bd9859b
("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context") turned out
to be a huge mistake when enabling Ironlake contexts as the GPU would
hang on either a MI_FLUSH or PIPE_CONTROL immediately following the
MI_SET_CONTEXT of an active mesa context (more vanilla contexts, e.g.
simple rendercopies with igt, do not suffer).
Ville found the following clue,
"[DevCTG+]: For the invalidate operation of the pipe control, the
following pointers are affected. The
invalidate operation affects the restore of these packets. If the pipe
control invalidate operation is completed
before the context save, the indirect pointers will not be restored from
memory.
1. Pipeline State Pointer
2. Media State Pointer
3. Constant Buffer Packet"
which suggests by us emitting the INVALIDATE prior to the MI_SET_CONTEXT,
we prevent the context-restore from chasing the dangling pointers within
the image, and explains why this likely prevents the GPU hang.
Signed-off-by: Chris Wilson <chris@chris-wilson.co.uk>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20190419111749.3910-1-chris@chris-wilson.co.uk
(cherry picked from commit 928f8f42310f244501a7c70daac82c196112c190 in drm-intel-next)
Cc: stable@vger.kernel.org
Bugzilla: https://bugs.freedesktop.org/show_bug.cgi?id=111014
Fixes: f2253bd9859b ("drm/i915/ringbuffer: EMIT_INVALIDATE after switch context")
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
|
|
commit 2d30ac5ed633 ("mtd: spi-nor: atmel-quadspi: Use spi-mem interface for atmel-quadspi driver")
removed the error path from atmel_qspi_init(), but not changed the
function's return type. Set void return type for atmel_qspi_init().
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
It is possible to request a transfer with a speed lower than supported
by the HW. This causes silent divider calculation underflow in
ssp_get_clk_div() which leads to a frequency higher than requested. Up to
maximum speed of the controller.
Set the minimum supported transfer speed and let the SPI core to
validate no transfers have speed lower than supported.
Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Add support for the 3.3V booster regulator embedded in stm32h7 and stm32mp1
devices, that can be used to supply ADC analog input switches.
This regulator is supplied by vdda. It's controlled by using SYSCFG:
- STM32H7 has a unique register to set/clear the booster enable bit
- STM32MP1 has separate set and clear registers to configure it.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The driver was registering buck regulators with unsupported range of
voltages for S2MPS11 devices. Basically it assumed that all 256 values
are possible for a single 8-bit I2C register controlling buck's voltage.
This is not true, as datasheet describes subset of these which can be
used.
For example for buck[12346] the minimum voltage is 650 mV which
corresponds to register value of 0x8. The driver was however
registering regulator starting at 600 mV, so for a step of 6.25 mV this
gave the same result. However this allowed to try to configure
regulators to unsupported values.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
On S2MPS11 device, the buck7 and buck8 regulator voltages start at 750
mV, not 600 mV. Using wrong minimal value caused shifting of these
regulator values by 150 mV (e.g. buck7 usually configured to v1.35 V was
reported as 1.2 V).
On most of the boards these regulators are left in default state so this
was only affecting reported voltage. However if any driver wanted to
change them, then effectively it would set voltage 150 mV higher than
intended.
Cc: <stable@vger.kernel.org>
Fixes: cb74685ecb39 ("regulator: s2mps11: Add samsung s2mps11 regulator driver")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The PixArt OEM mice are known for disconnecting every minute in
runlevel 1 or 3 if they are not always polled. So add quirk
ALWAYS_POLL for this Alienware branded Primax mouse as well.
Daniel Schepler (@dschepler) reported and tested the quirk.
Reference: https://github.com/sriemer/fix-linux-mouse/issues/15
Signed-off-by: Sebastian Parschauer <s.parschauer@gmx.de>
CC: stable@vger.kernel.org
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
Add the product ID for the 2nd Generation Intuos Pro
Small to the touchring coordinate adjustment block.
Signed-off-by: Aaron Armstrong Skomra <aaron.skomra@wacom.com>
Reviewed-by: Ping Cheng <ping.cheng@wacom.com>
Signed-off-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
|
|
Add support for the following ethtool commands:
ethtool -s|--change devname [msglvl N] [msglevel type on|off]
ethtool -S|--statistics devname
ethtool -i|--driver devname
ethtool -l|--show-channels devname
ethtool -L|--set-channels devname
ethtool -g|--show-ring devname
ethtool --reset devname
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the workqueue to handle management interrupts and
support for resets.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for passing traffic.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a driver framework for the Compute Engine Virtual NIC that will be
available in the future.
At this point the only functionality is loading the driver.
Signed-off-by: Catherine Sullivan <csully@google.com>
Signed-off-by: Sagi Shahar <sagis@google.com>
Signed-off-by: Jon Olson <jonolson@google.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Reviewed-by: Luigi Rizzo <lrizzo@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Create a blackhole net device that can be used for "dead"
dst entries instead of loopback device. This blackhole device differs
from loopback in few aspects: (a) It's not per-ns. (b) MTU on this
device is ETH_MIN_MTU (c) The xmit function is essentially kfree_skb().
and (d) since it's not registered it won't have ifindex.
Lower MTU effectively make the device not pass the MTU check during
the route check when a dst associated with the skb is dead.
Signed-off-by: Mahesh Bandewar <maheshb@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Rename r8153b_queue_wake() to r8153_queue_wake().
2. Correct the setting. The enable bit should be 0xd38c bit 0. Besides,
the 0xd38a bit 0 and 0xd398 bit 8 have to be cleared for both enabled
and disabled.
Signed-off-by: Hayes Wang <hayeswang@realtek.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove unneeded memset as alloc_etherdev is using kvzalloc which uses
__GFP_ZERO flag
Signed-off-by: Hariprasad Kelam <hariprasad.kelam@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The interface only supports 1 Tx queue so locking is introduced on
the Tx queue if XDP is enabled to make sure .ndo_start_xmit and
.ndo_xdp_xmit won't corrupt Tx ring
- Performance (SMMU off)
Benchmark XDP_SKB XDP_DRV
xdp1 291kpps 344kpps
rxdrop 282kpps 342kpps
- Performance (SMMU on)
Benchmark XDP_SKB XDP_DRV
xdp1 167kpps 324kpps
rxdrop 164kpps 323kpps
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use page_pool and it's DMA mapping capabilities for Rx buffers instead
of netdev/napi_alloc_frag()
Although this will result in a slight performance penalty on small sized
packets (~10%) the use of the API will allow to easily add XDP support.
The penalty won't be visible in network testing i.e ipef/netperf etc, it
only happens during raw packet drops.
Furthermore we intend to add recycling capabilities on the API
in the future. Once the recycling is added the performance penalty will
go away.
The only 'real' penalty is the slightly increased memory usage, since we
now allocate a page per packet instead of the amount of bytes we need +
skb metadata (difference is roughly 2kb per packet).
With a minimum of 4BG of RAM on the only SoC that has this NIC the
extra memory usage is negligible (a bit more on 64K pages)
Signed-off-by: Ilias Apalodimas <ilias.apalodimas@linaro.org>
Acked-by: Jesper Dangaard Brouer <brouer@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Similarly, other callers of idr_get_next_ul() suffer the same
overflow bug as they don't handle it properly either.
Introduce idr_for_each_entry_continue_ul() to help these callers
iterate from a given ID.
cls_flower needs more care here because it still has overflow when
does arg->cookie++, we have to fold its nested loops into one
and remove the arg->cookie++.
Fixes: 01683a146999 ("net: sched: refactor flower walk to iterate over idr")
Fixes: 12d6066c3b29 ("net/mlx5: Add flow counters idr")
Reported-by: Li Shuang <shuali@redhat.com>
Cc: Davide Caratti <dcaratti@redhat.com>
Cc: Vlad Buslov <vladbu@mellanox.com>
Cc: Chris Mi <chrism@mellanox.com>
Cc: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Cong Wang <xiyou.wangcong@gmail.com>
Tested-by: Davide Caratti <dcaratti@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
__vxlan_dev_create() destroys FDB using specific pointer which indicates
a fdb when error occurs.
But that pointer should not be used when register_netdevice() fails because
register_netdevice() internally destroys fdb when error occurs.
This patch makes vxlan_fdb_create() to do not link fdb entry to vxlan dev
internally.
Instead, a new function vxlan_fdb_insert() is added to link fdb to vxlan
dev.
vxlan_fdb_insert() is called after calling register_netdevice().
This routine can avoid situation that ->ndo_uninit() destroys fdb entry
in error path of register_netdevice().
Hence, error path of __vxlan_dev_create() routine can have an opportunity
to destroy default fdb entry by hand.
Test command
ip link add bonding_masters type vxlan id 0 group 239.1.1.1 \
dev enp0s9 dstport 4789
Splat looks like:
[ 213.392816] kasan: GPF could be caused by NULL-ptr deref or user memory access
[ 213.401257] general protection fault: 0000 [#1] SMP DEBUG_PAGEALLOC KASAN PTI
[ 213.402178] CPU: 0 PID: 1414 Comm: ip Not tainted 5.2.0-rc5+ #256
[ 213.402178] RIP: 0010:vxlan_fdb_destroy+0x120/0x220 [vxlan]
[ 213.402178] Code: df 48 8b 2b 48 89 fa 48 c1 ea 03 80 3c 02 00 0f 85 06 01 00 00 4c 8b 63 08 48 b8 00 00 00 00 00 fc d
[ 213.402178] RSP: 0018:ffff88810cb9f0a0 EFLAGS: 00010202
[ 213.402178] RAX: dffffc0000000000 RBX: ffff888101d4a8c8 RCX: 0000000000000000
[ 213.402178] RDX: 1bd5a00000000040 RSI: ffff888101d4a8c8 RDI: ffff888101d4a8d0
[ 213.402178] RBP: 0000000000000000 R08: fffffbfff22b72d9 R09: 0000000000000000
[ 213.402178] R10: 00000000ffffffef R11: 0000000000000000 R12: dead000000000200
[ 213.402178] R13: ffff88810cb9f1f8 R14: ffff88810efccda0 R15: ffff88810efccda0
[ 213.402178] FS: 00007f7f6621a0c0(0000) GS:ffff88811b000000(0000) knlGS:0000000000000000
[ 213.402178] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 213.402178] CR2: 000055746f0807d0 CR3: 00000001123e0000 CR4: 00000000001006f0
[ 213.402178] Call Trace:
[ 213.402178] __vxlan_dev_create+0x3a9/0x7d0 [vxlan]
[ 213.402178] ? vxlan_changelink+0x740/0x740 [vxlan]
[ 213.402178] ? rcu_read_unlock+0x60/0x60 [vxlan]
[ 213.402178] ? __kasan_kmalloc.constprop.3+0xa0/0xd0
[ 213.402178] vxlan_newlink+0x8d/0xc0 [vxlan]
[ 213.402178] ? __vxlan_dev_create+0x7d0/0x7d0 [vxlan]
[ 213.554119] ? __netlink_ns_capable+0xc3/0xf0
[ 213.554119] __rtnl_newlink+0xb75/0x1180
[ 213.554119] ? rtnl_link_unregister+0x230/0x230
[ ... ]
Fixes: 0241b836732f ("vxlan: fix default fdb entry netlink notify ordering during netdev create")
Suggested-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: Taehee Yoo <ap420073@gmail.com>
Acked-by: Roopa Prabhu <roopa@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The get_ts_info callback is used for obtaining information about
timestamping capabilities of a network device. On Spectrum-1, implement
it to advertise the PHC and the capability to do HW timestamping, and
the supported RX and TX filters.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SIOCSHWTSTAMP ioctl configures HW timestamping on a given port.
Dispatch the ioctls to per-chip handler (which add to ptp_ops). Find
which PTP messages need to be timestamped and configure MTPPPC
accordingly.
The SIOCGHWTSTAMP ioctl is getter for the current configuration.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Configure MTPTPT to set which message types should arrive under which
PTP trap, and MOGCR to clear the timestamp queue after its contents are
reported through PTP_ING_FIFO or PTP_EGR_FIFO.
With this configuration, PTP packets start arriving through the PTP
traps. However since timestamping is disabled by default and there is
currently no way to enable it, they will not be timestamped.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamped PTP packets and the corresponding timestamps
need to be kept in caches until both are available, at which point they are
matched up and packets forwarded as appropriate. However, not all packets
will ever see their timestamp, and not all timestamps will ever see their
packet. It is therefore necessary to dispose of such abandoned entries.
To that end, introduce a garbage collector to collect entries that have
not had their counterpart turn up within about a second. The GC
maintains a monotonously-increasing value of GC cycle. Every entry that
is put to the hash table is annotated with the GC cycle at which it
should be collected. When the GC runs, it walks the hash table, and
collects the objects according to their GC cycle annotation.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamps arrive through a pair of dedicated events:
MLXSW_TRAP_ID_PTP_ING_FIFO and _EGR_FIFO. The payload delivered with
those traps is contents of the timestamp FIFO at a given port in a given
direction. Add a Spectrum-1-specific handler for these two events which
decodes the timestamps and forwards them to the PTP module.
Add a function that parses a packet, dispatching to ptp_classify_raw(),
and decodes PTP message type, domain number, and sequence ID. Add a new
mlxsw dependency on the PTP classifier.
Add helpers that can store and retrieve unmatched timestamps and SKBs to
the hash table added in a preceding patch.
Add the matching code itself: upon arrival of a timestamp or a packet,
look up the corresponding unmatched entry, and match it up. If there is
none, add a new unmatched entry. This logic is the same on ingress as on
egress.
Packets and timestamps that never matched need to be eventually disposed
of. A garbage collector added in a follow-up patch will take care of
that. Since currently all this code is turned off, no crud will
accumulate in the hash table.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now, the PTP hardware clock code was only invoked in the process
context (SYS_clock_adjtime -> do_clock_adjtime -> k_clock::clock_adj ->
pc_clock_adjtime -> posix_clock_operations::clock_adjtime ->
ptp_clock_info::adjtime -> mlxsw_spectrum).
In order to enable HW timestamping, which is tied into trap handling, it
will be necessary to take the clock lock from the PCI queue handler
tasklets as well.
Therefore use the _bh variants when handling the clock lock. Incidentally,
Documentation/ptp/ptp.txt recommends _irqsave variants, but that's
unnecessarily strong for our needs.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add two ptp_ops: init and fini, to initialize and finalize the PTP
subsystem. Call as appropriate from mlxsw_sp_init() and _fini().
Lay the groundwork for Spectrum-1 support. On Spectrum-1, the received
timestamped packets and their corresponding timestamps arrive
independently, and need to be matched up. Introduce the related data types
and add to struct mlxsw_sp_ptp_state the hash table that will keep the
unmatched entries.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamps are delivered separately from the packets, and
need to paired up. Therefore, at some point after mlxsw_sp_port_xmit()
is invoked, it is necessary to involve the chip-specific driver code to
allow it to do the necessary bookkeeping and matching.
On Spectrum-2, timestamps are delivered in CQE. For that reason,
position the point of driver involvement into mlxsw_pci_cqe_sdq_handle()
to make it hopefully easier to extend for Spectrum-2 in the future.
To tell the driver what port the packet was sent on, keep tx_info
in SKB control buffer.
Introduce a new driver core interface mlxsw_core_ptp_transmitted(), a
driver callback ptp_transmitted, and a PTP op transmitted. The callee is
responsible for taking care of releasing the SKB passed to the new
interfaces, and correspondingly have the new stub callbacks just call
dev_kfree_skb_any().
Follow-up patches will introduce the actual content into
mlxsw_sp1_ptp_transmitted() in particular.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SKB control buffer is useful (and used) for bookkeeping of information
related to that SKB. Add helpers so that the mlxsw driver(s) can safely use
the buffer as well. The structure is currently empty, individual users will
add members to it as necessary.
Note that SKB allocation functions already clear the buffer, so the cleanup
is only necessary when ndo_start_xmit is called.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When configured, the Spectrum hardware can recognize PTP packets and
trap them to the CPU using dedicated traps, PTP0 and PTP1.
One reason to get PTP packets under dedicated traps is to have a
separate policer suitable for the amount of PTP traffic expected when
switch is operated as a boundary clock. For this, add two new trap
groups, MLXSW_REG_HTGT_TRAP_GROUP_SP_PTP0 and _PTP1, and associate the
two PTP traps with these two groups.
In the driver, specifically for Spectrum-1, event PTP packets will need
to be paired up with their timestamps. Those arrive through a different
set of traps, added later in the patch set. To support this future use,
introduce a new PTP op, ptp_receive.
It is possible to configure which PTP messages should be trapped under
which PTP trap. On Spectrum systems, we will use PTP0 for event
packets (which need timestamping), and PTP1 for control packets (which
do not). Thus configure PTP0 trap with a custom callback that defers to
the ptp_receive op.
Additionally, L2 PTP packets are actually trapped through the LLDP trap,
not through any of the PTP traps. So treat the LLDP trap the same way as
the PTP0 trap. Unlike PTP traps, which are currently still disabled,
LLDP trap is active. Correspondingly, have all the implementations of
the ptp_receive op return true, which the handler treats as a signal to
forward the packet immediately.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Carry a chip-specific listener array in mlxsw_sp->listeners and
listeners_count. Register listeners from that array in
mlxsw_sp_traps_init(). Add a new listener array for Spectrum-1 traps and
configure the newly-added mlxsw_sp->listeners with this array.
The listener array is empty for now, the events will be added in a later
patch.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Spectrum-1, timestamps for PTP packets are delivered through queues
of ingress and egress timestamps. There are two event traps
corresponding to activity on each of those queues. This mechanism is
absent on Spectrum-2, and therefore the traps should only be registered
on Spectrum-1.
Extract out of mlxsw_sp_traps_init() a generic helper,
mlxsw_sp_traps_register(), and likewise with _unregister(). The new helpers
will later be called with Spectrum-1-specific traps.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This register serves to configure global parameters of certain
monitoring operations. The following patches will use it to configure
that when PTP timestamps are delivered through the PTP FIFO traps, the
FIFO in question is cleared as well.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MTPPTR is used for reading the per port PTP timestamp FIFO.
Signed-off-by: Petr Machata <petrm@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
