| Age | Commit message (Collapse) | Author |
|---|
|
Pull drm fixes from Dave Airlie:
"Here is this weeks non-intel hw vuln fixes pull. Three drivers, all
small fixes.
i915:
- MOCS table fixes for EHL and TGL
- Update Display's rawclock on resume
- GVT's dmabuf reference drop fix
amdgpu:
- Fix a potential crash in firmware parsing
sun4i:
- One fix to the dotclock dividers range for sun4i"
* tag 'drm-fixes-2019-11-15' of git://anongit.freedesktop.org/drm/drm:
drm/amdgpu: fix null pointer deref in firmware header printing
drm/i915/tgl: MOCS table update
Revert "drm/i915/ehl: Update MOCS table for EHL"
drm/sun4i: tcon: Set min division of TCON0_DCLK to 1.
drm/i915: update rawclk also on resume
drm/i915/gvt: fix dropping obj reference twice
|
|
Some device only support 4 TCs, but the driver check the total
bandwidth of 8 TCs, so may cause wrong configurations write to
the hw.
This patch uses hdev->tc_max to instead HNAE3_MAX_TC to fix it.
Fixes: e432abfb99e5 ("net: hns3: add common validation in hclge_dcb")
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a TC's PFC is disabled or enabled, the RX private buffer for
this TC need to be changed too, otherwise this may cause packet
dropped problem.
This patch fixes it by calling hclge_buffer_alloc to reallocate
buffer when pfc_en changes.
Fixes: cacde272dd00 ("net: hns3: Add hclge_dcb module for the support of DCB feature")
Signed-off-by: Yunsheng Lin <linyunsheng@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Previously, hns3 driver just directly send specific setting bit
and mask bits of MAC VLAN switch parameter to the firmware, it
can not be compatible with the old firmware, because the old one
ignores mask bits and covers all bits with new setting bits.
So when running with old firmware, the communication between PF
and VF will fail after resetting or configuring spoof check, since
they will do the MAC VLAN switch parameter configuration.
This patch fixes this problem by reading switch parameter firstly,
then just modifies the corresponding bit and sends it to firmware.
Fixes: dd2956eab104 ("net: hns3: not allow SSU loopback while execute ethtool -t dev")
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: Huazhong Tan <tanhuazhong@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pre-allocates buffers sufficient for the maximum supported MTU (2026) in
order to eliminate the possibility of resource exhaustion when changing the
MTU while the device is up.
Signed-off-by: Ulrich Hecht <uli+renesas@fpond.eu>
Reviewed-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://people.freedesktop.org/~agd5f/linux into drm-fixes
drm-fixes-5.4-2019-11-14:
amdgpu:
- Fix a potential crash in firmware parsing
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Alex Deucher <alexdeucher@gmail.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191114221354.3914-1-alexander.deucher@amd.com
|
|
git://anongit.freedesktop.org/drm/drm-misc into drm-fixes
- One fix to the dotclock dividers range for sun4i
Signed-off-by: Dave Airlie <airlied@redhat.com>
From: Maxime Ripard <mripard@kernel.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20191113142645.GA967172@gilmour.lan
|
|
v2: declare as (struct common_firmware_header *) type because
struct xxx_firmware_header inherits from it
When CE's ucode_id(8) is used to get sdma_hdr, we will be accessing an
unallocated amdgpu_firmware_info instance.
This issue appears on rhel7.7 with gcc 4.8.5. Newer compilers might have
optimized out such 'defined but not referenced' variable.
[ 1120.798564] BUG: unable to handle kernel NULL pointer dereference at 000000000000000a
[ 1120.806703] IP: [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1120.813693] PGD 80000002603ff067 PUD 271b8d067 PMD 0
[ 1120.818931] Oops: 0000 [#1] SMP
[ 1120.822245] Modules linked in: amdgpu(OE+) amdkcl(OE) amd_iommu_v2 amdttm(OE) amd_sched(OE) xt_CHECKSUM ipt_MASQUERADE nf_nat_masquerade_ipv4 tun bridge stp llc devlink ip6t_rpfilter ip6t_REJECT nf_reject_ipv6 ipt_REJECT nf_reject_ipv4 xt_conntrack ebtable_nat ip6table_nat nf_conntrack_ipv6 nf_defrag_ipv6 nf_nat_ipv6 ip6table_mangle ip6table_security ip6table_raw iptable_nat nf_conntrack_ipv4 nf_defrag_ipv4 nf_nat_ipv4 nf_nat iptable_mangle iptable_security iptable_raw nf_conntrack libcrc32c ip_set nfnetlink ebtable_filter ebtables ip6table_filter ip6_tables iptable_filter sunrpc dm_mirror dm_region_hash dm_log dm_mod intel_pmc_core intel_powerclamp coretemp intel_rapl joydev kvm_intel eeepc_wmi asus_wmi kvm sparse_keymap iTCO_wdt irqbypass rfkill crc32_pclmul snd_hda_codec_realtek mxm_wmi ghash_clmulni_intel intel_wmi_thunderbolt iTCO_vendor_support snd_hda_codec_generic snd_hda_codec_hdmi aesni_intel lrw gf128mul glue_helper ablk_helper sg cryptd pcspkr snd_hda_intel snd_hda_codec snd_hda_core snd_hwdep snd_seq snd_seq_device snd_pcm snd_timer snd pinctrl_sunrisepoint pinctrl_intel soundcore acpi_pad mei_me wmi mei i2c_i801 pcc_cpufreq ip_tables ext4 mbcache jbd2 sd_mod crc_t10dif crct10dif_generic i915 i2c_algo_bit iosf_mbi drm_kms_helper e1000e syscopyarea sysfillrect sysimgblt fb_sys_fops ahci libahci drm ptp libata crct10dif_pclmul crct10dif_common crc32c_intel serio_raw pps_core drm_panel_orientation_quirks video i2c_hid
[ 1120.954136] CPU: 4 PID: 2426 Comm: modprobe Tainted: G OE ------------ 3.10.0-1062.el7.x86_64 #1
[ 1120.964390] Hardware name: System manufacturer System Product Name/Z170-A, BIOS 1302 11/09/2015
[ 1120.973321] task: ffff991ef1e3c1c0 ti: ffff991ee625c000 task.ti: ffff991ee625c000
[ 1120.981020] RIP: 0010:[<ffffffffc0e3c9b3>] [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1120.990483] RSP: 0018:ffff991ee625f950 EFLAGS: 00010202
[ 1120.995935] RAX: 0000000000000002 RBX: ffff991edf6b2d38 RCX: ffff991edf6a0000
[ 1121.003391] RDX: 0000000000000000 RSI: ffff991f01d13898 RDI: ffffffffc110afb3
[ 1121.010706] RBP: ffff991ee625f9b0 R08: 0000000000000000 R09: 0000000000000000
[ 1121.018029] R10: 00000000000004c4 R11: ffff991ee625f64e R12: ffff991edf6b3220
[ 1121.025353] R13: ffff991edf6a0000 R14: 0000000000000008 R15: ffff991edf6b2d30
[ 1121.032666] FS: 00007f97b0c0b740(0000) GS:ffff991f01d00000(0000) knlGS:0000000000000000
[ 1121.041000] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 1121.046880] CR2: 000000000000000a CR3: 000000025e604000 CR4: 00000000003607e0
[ 1121.054239] DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
[ 1121.061631] DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
[ 1121.068938] Call Trace:
[ 1121.071494] [<ffffffffc0e3dba8>] psp_hw_init+0x218/0x270 [amdgpu]
[ 1121.077886] [<ffffffffc0da3188>] amdgpu_device_fw_loading+0xe8/0x160 [amdgpu]
[ 1121.085296] [<ffffffffc0e3b34c>] ? vega10_ih_irq_init+0x4bc/0x730 [amdgpu]
[ 1121.092534] [<ffffffffc0da5c75>] amdgpu_device_init+0x1495/0x1c90 [amdgpu]
[ 1121.099675] [<ffffffffc0da9cab>] amdgpu_driver_load_kms+0x8b/0x2f0 [amdgpu]
[ 1121.106888] [<ffffffffc01b25cf>] drm_dev_register+0x12f/0x1d0 [drm]
[ 1121.113419] [<ffffffffa4dcdfd8>] ? pci_enable_device_flags+0xe8/0x140
[ 1121.120183] [<ffffffffc0da260a>] amdgpu_pci_probe+0xca/0x170 [amdgpu]
[ 1121.126919] [<ffffffffa4dcf97a>] local_pci_probe+0x4a/0xb0
[ 1121.132622] [<ffffffffa4dd10c9>] pci_device_probe+0x109/0x160
[ 1121.138607] [<ffffffffa4eb4205>] driver_probe_device+0xc5/0x3e0
[ 1121.144766] [<ffffffffa4eb4603>] __driver_attach+0x93/0xa0
[ 1121.150507] [<ffffffffa4eb4570>] ? __device_attach+0x50/0x50
[ 1121.156422] [<ffffffffa4eb1da5>] bus_for_each_dev+0x75/0xc0
[ 1121.162213] [<ffffffffa4eb3b7e>] driver_attach+0x1e/0x20
[ 1121.167771] [<ffffffffa4eb3620>] bus_add_driver+0x200/0x2d0
[ 1121.173590] [<ffffffffa4eb4c94>] driver_register+0x64/0xf0
[ 1121.179345] [<ffffffffa4dd0905>] __pci_register_driver+0xa5/0xc0
[ 1121.185593] [<ffffffffc099f000>] ? 0xffffffffc099efff
[ 1121.190914] [<ffffffffc099f0a4>] amdgpu_init+0xa4/0xb0 [amdgpu]
[ 1121.197101] [<ffffffffa4a0210a>] do_one_initcall+0xba/0x240
[ 1121.202901] [<ffffffffa4b1c90a>] load_module+0x271a/0x2bb0
[ 1121.208598] [<ffffffffa4dad740>] ? ddebug_proc_write+0x100/0x100
[ 1121.214894] [<ffffffffa4b1ce8f>] SyS_init_module+0xef/0x140
[ 1121.220698] [<ffffffffa518bede>] system_call_fastpath+0x25/0x2a
[ 1121.226870] Code: b4 01 60 a2 00 00 31 c0 e8 83 60 33 e4 41 8b 47 08 48 8b 4d d0 48 c7 c7 b3 af 10 c1 48 69 c0 68 07 00 00 48 8b 84 01 60 a2 00 00 <48> 8b 70 08 31 c0 48 89 75 c8 e8 56 60 33 e4 48 8b 4d d0 48 c7
[ 1121.247422] RIP [<ffffffffc0e3c9b3>] psp_np_fw_load+0x1e3/0x390 [amdgpu]
[ 1121.254432] RSP <ffff991ee625f950>
[ 1121.258017] CR2: 000000000000000a
[ 1121.261427] ---[ end trace e98b35387ede75bd ]---
Signed-off-by: Xiaojie Yuan <xiaojie.yuan@amd.com>
Fixes: c5fb912653dae3f878 ("drm/amdgpu: add firmware header printing for psp fw loading (v2)")
Reviewed-by: Kevin Wang <kevin1.wang@amd.com>
Signed-off-by: Alex Deucher <alexander.deucher@amd.com>
|
|
The driver misses calling destroy_workqueue in remove like what is done
when probe fails.
Add the missed calls to fix it.
Signed-off-by: Chuhong Yuan <hslester96@gmail.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Some versions of gcc (so far 6.3 and 7.4) throw a warning:
drivers/block/rbd.c: In function 'rbd_object_map_callback':
drivers/block/rbd.c:2124:21: warning: 'current_state' may be used uninitialized in this function [-Wmaybe-uninitialized]
(current_state == OBJECT_EXISTS && state == OBJECT_EXISTS_CLEAN))
drivers/block/rbd.c:2092:23: note: 'current_state' was declared here
u8 state, new_state, current_state;
^~~~~~~~~~~~~
It's bogus because all current_state accesses are guarded by
has_current_state.
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Dongsheng Yang <dongsheng.yang@easystack.cn>
|
|
Pull RDMA fixes from Jason Gunthorpe:
"Bug fixes for old bugs in the hns and hfi1 drivers:
- Calculate various values in hns properly to avoid over/underflows
in some cases
- Fix an oops, PCI negotiation on Gen4 systems, and bugs related to
retries"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma:
RDMA/hns: Correct the value of srq_desc_size
RDMA/hns: Correct the value of HNS_ROCE_HEM_CHUNK_LEN
IB/hfi1: TID RDMA WRITE should not return IB_WC_RNR_RETRY_EXC_ERR
IB/hfi1: Calculate flow weight based on QP MTU for TID RDMA
IB/hfi1: Ensure r_tid_ack is valid before building TID RDMA ACK packet
IB/hfi1: Ensure full Gen3 speed in a Gen4 system
|
|
The quirks2 are parsed and set (e.g. from DT) before the quirk for broken
HS200 is set in the driver.
The driver needs to enable just this flag, not rewrite the whole quirk set.
Fixes: 7871aa60ae00 ("mmc: sdhci-of-at91: add quirk for broken HS200")
Signed-off-by: Eugen Hristev <eugen.hristev@microchip.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mkl/linux-can
Marc Kleine-Budde says:
====================
pull-request: can 2019-11-14
here another pull request for net/master consisting of one patch (including my S-o-b).
Jouni Hogander's patch fixes a memory leak found by the syzbot in the slcan
driver's error path.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kvalo/wireless-drivers
Kalle Valo says:
====================
wireless-drivers fixes for v5.4
Hopefully last fixes for v5.4, only one iwlwifi fix this time.
iwlwifi
* fix A-MSDU data corruption when using CCMP/GCMP ciphers
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is fixing memory leak reported by Syzkaller:
BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
hex dump (first 32 bytes):
73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
[<0000000083306e66>] kvmalloc_node+0x3a/0xc0
[<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
[<0000000061a996c9>] slcan_open+0x3ae/0x9a0
[<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
[<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
[<000000004de5a617>] tty_ioctl+0x48d/0x1590
[<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
[<0000000059068dbc>] ksys_ioctl+0x99/0xb0
[<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
[<0000000053d0332e>] do_syscall_64+0x16f/0x580
[<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<000000008ea75434>] 0xffffffffffffffff
Cc: Wolfgang Grandegger <wg@grandegger.com>
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
|
|
This code is supposed to test for negative error codes and partial
reads, but because sizeof() is size_t (unsigned) type then negative
error codes are type promoted to high positive values and the condition
doesn't work as expected.
Fixes: 332f989a3b00 ("CDC-NCM: handle incomplete transfer of MTU")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into fixes
gpio fixes for v5.4-rc8
- fix debounce times in max776520 and bd70528
- fix parallel build of gpio tools
|
|
The Terra Pad 1061 has the usual micro-USB-B id-pin handler, but instead
of controlling the actual micro-USB-B it turns the 5V boost for the
tablet's USB-A connector and its keyboard-cover connector off.
The actual micro-USB-B connector on the tablet is wired for charging only,
and its id pin is *not* connected to the GPIO which is used for the
(broken) id-pin event handler in the DSDT.
While at it not only add a comment why the Terra Pad 1061 is on the
blacklist, but also fix the missing comment for the Minix Neo Z83-4 entry.
Fixes: 61f7f7c8f978 ("gpiolib: acpi: Add gpiolib_acpi_run_edge_events_on_boot option and blacklist")
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The bspec was just updated with a minor correction to entry 61 (it
shouldn't have had the SCF bit set).
v2:
- Add a MOCS_ENTRY_UNUSED() and use it to declare the
explicitly-reserved MOCS entries. (Lucas)
- Move the warning suppression from the Makefile to a #pragma that only
affects the TGL table. (Lucas)
v3:
- Entries 16 and 17 are identical to ICL now, so no need to explicitly
adjust them (or mess with compiler warning overrides).
Bspec: 45101
Fixes: 2ddf992179c4 ("drm/i915/tgl: Define MOCS entries for Tigerlake")
Cc: Tomasz Lis <tomasz.lis@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: Francisco Jerez <francisco.jerez.plata@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112224757.25116-2-matthew.d.roper@intel.com
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
Reviewed-by: Lucas De Marchi <lucas.demarchi@intel.com>
Reviewed-by: Tomasz Lis <tomasz.lis@intel.com>
(cherry picked from commit bfb0e8e63d865559cc97af235aea583b7dcc235f)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
This reverts commit f4071997f1de016780ec6b79c63d90cd5886ee83.
These extra EHL entries won't behave as expected without a bit more work
on the kernel side so let's drop them until that kernel work has had a
chance to land. Userspace trying to use these new entries won't get the
advantage of the new functionality these entries are meant to provide,
but at least it won't misbehave.
When we do add these back in the future, we'll probably want to
explicitly use separate tables for ICL and EHL so that userspace
software that mistakenly uses these entries (which are undefined on ICL)
sees the same behavior it sees with all the other undefined entries.
Cc: Francisco Jerez <francisco.jerez.plata@intel.com>
Cc: Jon Bloomfield <jon.bloomfield@intel.com>
Cc: Lucas De Marchi <lucas.demarchi@intel.com>
Cc: <stable@vger.kernel.org> # v5.3+
Fixes: f4071997f1de ("drm/i915/ehl: Update MOCS table for EHL")
Signed-off-by: Matt Roper <matthew.d.roper@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112224757.25116-1-matthew.d.roper@intel.com
Reviewed-by: Francisco Jerez <currojerez@riseup.net>
(cherry picked from commit 046091758b50a5fff79726a31c1391614a3d84c8)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"Fixes to the Synaptics RMI4 driver and fix for use after free in error
path handling of the Cypress TTSP driver"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: cyttsp4_core - fix use after free bug
Input: synaptics-rmi4 - clear IRQ enables for F54
Input: synaptics-rmi4 - remove unused result_bits mask
Input: synaptics-rmi4 - do not consume more data than we have (F11, F12)
Input: synaptics-rmi4 - disable the relative position IRQ in the F12 driver
Input: synaptics-rmi4 - fix video buffer size
|
|
Driver/net/can/slcan.c is derived from slip.c. Memory leak was detected
by Syzkaller in slcan. Same issue exists in slip.c and this patch is
addressing the leak in slip.c.
Here is the slcan memory leak trace reported by Syzkaller:
BUG: memory leak unreferenced object 0xffff888067f65500 (size 4096):
comm "syz-executor043", pid 454, jiffies 4294759719 (age 11.930s)
hex dump (first 32 bytes):
73 6c 63 61 6e 30 00 00 00 00 00 00 00 00 00 00 slcan0..........
00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 ................
backtrace:
[<00000000a06eec0d>] __kmalloc+0x18b/0x2c0
[<0000000083306e66>] kvmalloc_node+0x3a/0xc0
[<000000006ac27f87>] alloc_netdev_mqs+0x17a/0x1080
[<0000000061a996c9>] slcan_open+0x3ae/0x9a0
[<000000001226f0f9>] tty_ldisc_open.isra.1+0x76/0xc0
[<0000000019289631>] tty_set_ldisc+0x28c/0x5f0
[<000000004de5a617>] tty_ioctl+0x48d/0x1590
[<00000000daef496f>] do_vfs_ioctl+0x1c7/0x1510
[<0000000059068dbc>] ksys_ioctl+0x99/0xb0
[<000000009a6eb334>] __x64_sys_ioctl+0x78/0xb0
[<0000000053d0332e>] do_syscall_64+0x16f/0x580
[<0000000021b83b99>] entry_SYSCALL_64_after_hwframe+0x44/0xa9
[<000000008ea75434>] 0xfffffffffffffff
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Lukas Bulwahn <lukas.bulwahn@gmail.com>
Signed-off-by: Jouni Hogander <jouni.hogander@unikie.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
These are the Foxconn-branded variants of the Dell DW5821e modules,
same USB layout as those.
The QMI interface is exposed in USB configuration #1:
P: Vendor=0489 ProdID=e0b4 Rev=03.18
S: Manufacturer=FII
S: Product=T77W968 LTE
S: SerialNumber=0123456789ABCDEF
C: #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
I: If#=0x0 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=qmi_wwan
I: If#=0x1 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=usbhid
I: If#=0x2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x3 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
I: If#=0x5 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
Signed-off-by: Aleksander Morgado <aleksander@aleksander.es>
Acked-by: Bjørn Mork <bjorn@mork.no>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The datasheet of V3s (and various other chips) wrote
that TCON0_DCLK_DIV can be >= 1 if only dclk is used,
and must >= 6 if dclk1 or dclk2 is used. As currently
neither dclk1 nor dclk2 is used (no writes to these
bits), let's set minimal division to 1.
If this minimal division is 6, some common dot clock
frequencies can't be produced (e.g. 30MHz will not be
possible and will fallback to 25MHz), which is
obviously not an expected behaviour.
Signed-off-by: Yunhao Tian <t123yh@outlook.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/linux-arm-kernel/MN2PR08MB57905AD8A00C08DA219377C989760@MN2PR08MB5790.namprd08.prod.outlook.com/
|
|
The setup_dpio() function tries to allocate a number of channels equal
to the number of CPUs online. When there are not enough DPCON objects
already probed, the function will return EPROBE_DEFER. When this
happens, the already allocated channels are not freed. This results in
the incapacity of properly probing the next time around.
Fix this by freeing the channels on the error path.
Fixes: d7f5a9d89a55 ("dpaa2-eth: defer probe on object allocate")
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device md->input is used after it is released. Setting the device
data to NULL is unnecessary as the device is never used again. Instead,
md->input should be assigned NULL to avoid accessing the freed memory
accidently. Besides, checking md->si against NULL is superfluous as it
points to a variable address, which cannot be NULL.
Signed-off-by: Pan Bian <bianpan2016@163.com>
Link: https://lore.kernel.org/r/1572936379-6423-1-git-send-email-bianpan2016@163.com
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
The driver for F54 just polls the status and doesn't even have a IRQ
handler registered. Make sure to disable all F54 IRQs, so we don't crash
the kernel on a nonexistent handler.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Link: https://lore.kernel.org/r/20191105114402.6009-1-l.stach@pengutronix.de
Cc: stable@vger.kernel.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This went into staging in rc7. It turns out that was a mistake, and
apparently it wasn't even supposed to go there at all, but be introduced
as a regular filesystem.
We don't try to sneak in whole new filesystems this late in the rc, just
delete the whole thing, and it can be re-introduced as a proper patch
with proper acks from actual filesystem people instead of some odd
late-rc staging back-door.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
drm-intel-fixes
gvt-fixes-2019-11-12
- Fix dmabuf reference drop (Pan)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
From: Zhenyu Wang <zhenyuw@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191112061834.GN4196@zhen-hp.sh.intel.com
|
|
Since CNP it's possible for rawclk to have two different values, 19.2
and 24 MHz. If the value indicated by SFUSE_STRAP register is different
from the power on default for PCH_RAWCLK_FREQ, we'll end up having a
mismatch between the rawclk hardware and software states after
suspend/resume. On previous platforms this used to work by accident,
because the power on defaults worked just fine.
Update the rawclk also on resume. The natural place to do this would be
intel_modeset_init_hw(), however VLV/CHV need it done before
intel_power_domains_init_hw(). Thus put it there even if it feels
slightly out of place.
v2: Call intel_update_rawclck() in intel_power_domains_init_hw() for all
platforms (Ville).
Reported-by: Shawn Lee <shawn.c.lee@intel.com>
Cc: Shawn Lee <shawn.c.lee@intel.com>
Cc: Ville Syrjala <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Tested-by: Shawn Lee <shawn.c.lee@intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20191101142024.13877-1-jani.nikula@intel.com
(cherry picked from commit 59ed05ccdded5eb18ce012eff3d01798ac8535fa)
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull x86 TSX Async Abort and iTLB Multihit mitigations from Thomas Gleixner:
"The performance deterioration departement is not proud at all of
presenting the seventh installment of speculation mitigations and
hardware misfeature workarounds:
1) TSX Async Abort (TAA) - 'The Annoying Affair'
TAA is a hardware vulnerability that allows unprivileged
speculative access to data which is available in various CPU
internal buffers by using asynchronous aborts within an Intel TSX
transactional region.
The mitigation depends on a microcode update providing a new MSR
which allows to disable TSX in the CPU. CPUs which have no
microcode update can be mitigated by disabling TSX in the BIOS if
the BIOS provides a tunable.
Newer CPUs will have a bit set which indicates that the CPU is not
vulnerable, but the MSR to disable TSX will be available
nevertheless as it is an architected MSR. That means the kernel
provides the ability to disable TSX on the kernel command line,
which is useful as TSX is a truly useful mechanism to accelerate
side channel attacks of all sorts.
2) iITLB Multihit (NX) - 'No eXcuses'
iTLB Multihit is an erratum where some Intel processors may incur
a machine check error, possibly resulting in an unrecoverable CPU
lockup, when an instruction fetch hits multiple entries in the
instruction TLB. This can occur when the page size is changed
along with either the physical address or cache type. A malicious
guest running on a virtualized system can exploit this erratum to
perform a denial of service attack.
The workaround is that KVM marks huge pages in the extended page
tables as not executable (NX). If the guest attempts to execute in
such a page, the page is broken down into 4k pages which are
marked executable. The workaround comes with a mechanism to
recover these shattered huge pages over time.
Both issues come with full documentation in the hardware
vulnerabilities section of the Linux kernel user's and administrator's
guide.
Thanks to all patch authors and reviewers who had the extraordinary
priviledge to be exposed to this nuisance.
Special thanks to Borislav Petkov for polishing the final TAA patch
set and to Paolo Bonzini for shepherding the KVM iTLB workarounds and
providing also the backports to stable kernels for those!"
* 'x86-pti-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
x86/speculation/taa: Fix printing of TAA_MSG_SMT on IBRS_ALL CPUs
Documentation: Add ITLB_MULTIHIT documentation
kvm: x86: mmu: Recovery of shattered NX large pages
kvm: Add helper function for creating VM worker threads
kvm: mmu: ITLB_MULTIHIT mitigation
cpu/speculation: Uninline and export CPU mitigations helpers
x86/cpu: Add Tremont to the cpu vulnerability whitelist
x86/bugs: Add ITLB_MULTIHIT bug infrastructure
x86/tsx: Add config options to set tsx=on|off|auto
x86/speculation/taa: Add documentation for TSX Async Abort
x86/tsx: Add "auto" option to the tsx= cmdline parameter
kvm/x86: Export MDS_NO=0 to guests when TSX is enabled
x86/speculation/taa: Add sysfs reporting for TSX Async Abort
x86/speculation/taa: Add mitigation for TSX Async Abort
x86/cpu: Add a "tsx=" cmdline option with TSX disabled by default
x86/cpu: Add a helper function x86_read_arch_cap_msr()
x86/msr: Add the IA32_TSX_CTRL MSR
|
|
The debounce time passed to gpiod_set_debounce() is specified in
microseconds, so make sure to use the correct unit when computing the
register values, which denote delays in milliseconds.
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: <stable@vger.kernel.org>
Fixes: 18bc64b3aebf ("gpio: Initial support for ROHM bd70528 GPIO block")
[Bartosz: fixed a typo in commit message]
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
When converting milliseconds to microseconds in commit fffa6af94894
("gpio: max77620: Use correct unit for debounce times") some ~1 ms gaps
were introduced between the various ranges supported by the controller.
Fix this by changing the start of each range to the value immediately
following the end of the previous range. This way a debounce time of,
say 8250 us will translate into 16 ms instead of returning an -EINVAL
error.
Typically the debounce delay is only ever set through device tree and
specified in milliseconds, so we can never really hit this issue because
debounce times are always a multiple of 1000 us.
The only notable exception for this is drivers/mmc/host/mmc-spi.c where
the CD GPIO is requested, which passes a 1 us debounce time. According
to a comment preceeding that code this should actually be 1 ms (i.e.
1000 us).
Reported-by: Pavel Machek <pavel@denx.de>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Acked-by: Pavel Machek <pavel@denx.de>
Cc: <stable@vger.kernel.org>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
|
|
Fix coccinelle warning:
./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62
Fix this by using IS_ERR before PTR_ERR
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I2C communication errors (-EREMOTEIO) during the IRQ handler of nxp-nci
result in a NULL pointer dereference at the moment:
BUG: kernel NULL pointer dereference, address: 0000000000000000
Oops: 0002 [#1] PREEMPT SMP NOPTI
CPU: 1 PID: 355 Comm: irq/137-nxp-nci Not tainted 5.4.0-rc6 #1
RIP: 0010:skb_queue_tail+0x25/0x50
Call Trace:
nci_recv_frame+0x36/0x90 [nci]
nxp_nci_i2c_irq_thread_fn+0xd1/0x285 [nxp_nci_i2c]
? preempt_count_add+0x68/0xa0
? irq_forced_thread_fn+0x80/0x80
irq_thread_fn+0x20/0x60
irq_thread+0xee/0x180
? wake_threads_waitq+0x30/0x30
kthread+0xfb/0x130
? irq_thread_check_affinity+0xd0/0xd0
? kthread_park+0x90/0x90
ret_from_fork+0x1f/0x40
Afterward the kernel must be rebooted to work properly again.
This happens because it attempts to call nci_recv_frame() with skb == NULL.
However, unlike nxp_nci_fw_recv_frame(), nci_recv_frame() does not have any
NULL checks for skb, causing the NULL pointer dereference.
Change the code to call only nxp_nci_fw_recv_frame() in case of an error.
Make sure to log it so it is obvious that a communication error occurred.
The error above then becomes:
nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121
nci: __nci_request: wait_for_completion_interruptible_timeout failed 0
nxp-nci_i2c i2c-NXP1001:00: NFC: Read failed with error -121
Fixes: 6be88670fc59 ("NFC: nxp-nci_i2c: Add I2C support to NXP NCI driver")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call devlink enable only during probe time and avoid deadlock
during reload.
Reported-by: Shalom Toledo <shalomt@mellanox.com>
Fixes: 5a508a254bed ("devlink: disallow reload operation during device cleanup")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Tested-by: Shalom Toledo <shalomt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This fixes two different classes of bugs in the Intel graphics hardware:
MMIO register read hang:
"On Intels Gen8 and Gen9 Graphics hardware, a read of specific graphics
MMIO registers when the product is in certain low power states causes
a system hang.
There are two potential triggers for DoS:
a) H/W corruption of the RC6 save/restore vector
b) Hard hang within the MIPI hardware
This prevents the DoS in two areas of the hardware:
1) Detect corruption of RC6 address on exit from low-power state,
and if we find it corrupted, disable RC6 and RPM
2) Permanently lower the MIPI MMIO timeout"
Blitter command streamer unrestricted memory accesses:
"On Intels Gen9 Graphics hardware the Blitter Command Streamer (BCS)
allows writing to Memory Mapped Input Output (MMIO) that should be
blocked. With modifications of page tables, this can lead to privilege
escalation. This exposure is limited to the Guest Physical Address
space and does not allow for access outside of the graphics virtual
machine.
This series establishes a software parser into the Blitter command
stream to scan for, and prevent, reads or writes to MMIO's that should
not be accessible to non-privileged contexts.
Much of the command parser infrastructure has existed for some time,
and is used on Ivybridge/Haswell/Valleyview derived products to allow
the use of features normally blocked by hardware. In this legacy
context, the command parser is employed to allow normally unprivileged
submissions to be run with elevated privileges in order to grant
access to a limited set of extra capabilities. In this mode the parser
is optional; In the event that the parser finds any construct that it
cannot properly validate (e.g. nested command buffers), it simply
aborts the scan and submits the buffer in non-privileged mode.
For Gen9 Graphics, this series makes the parser mandatory for all
Blitter submissions. The incoming user buffer is first copied to a
kernel owned buffer, and parsed. If all checks are successful the
kernel owned buffer is mapped READ-ONLY and submitted on behalf of the
user. If any checks fail, or the parser is unable to complete the scan
(nested buffers), it is forcibly rejected. The successfully scanned
buffer is executed with NORMAL user privileges (key difference from
legacy usage).
Modern usermode does not use the Blitter on later hardware, having
switched over to using the 3D engine instead for performance reasons.
There are however some legacy usermode apps that rely on Blitter,
notably the SNA X-Server. There are no known usermode applications
that require nested command buffers on the Blitter, so the forcible
rejection of such buffers in this patch series is considered an
acceptable limitation"
* Intel graphics fixes in emailed bundle from Jon Bloomfield <jon.bloomfield@intel.com>:
drm/i915/cmdparser: Fix jump whitelist clearing
drm/i915/gen8+: Add RC6 CTX corruption WA
drm/i915: Lower RM timeout to avoid DSI hard hangs
drm/i915/cmdparser: Ignore Length operands during command matching
drm/i915/cmdparser: Add support for backward jumps
drm/i915/cmdparser: Use explicit goto for error paths
drm/i915: Add gen9 BCS cmdparsing
drm/i915: Allow parsing of unsized batches
drm/i915: Support ro ppgtt mapped cmdparser shadow buffers
drm/i915: Add support for mandatory cmdparsing
drm/i915: Remove Master tables from cmdparser
drm/i915: Disable Secure Batches for gen6+
drm/i915: Rename gen7 cmdparser tables
|
|
When PHY is not powered, the probe function fail and some resource are
still unallocated.
Furthermore some BUG happens:
dwmac-sun8i 5020000.ethernet: EMAC reset timeout
------------[ cut here ]------------
kernel BUG at /linux-next/net/core/dev.c:9844!
So let's use the right function (stmmac_pltfr_remove) in the error path.
Fixes: 9f93ac8d4085 ("net-next: stmmac: Add dwmac-sun8i")
Cc: <stable@vger.kernel.org> # v4.15+
Signed-off-by: Corentin Labbe <clabbe@baylibre.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Three small changes: two in the core and one in the qla2xxx driver.
The sg_tablesize fix affects a thinko in the migration to blk-mq of
certain legacy drivers which could cause an oops and the sd core
change should only affect zoned block devices which were wrongly
suppressing error messages for reset all zones"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: core: Handle drivers which set sg_tablesize to zero
scsi: qla2xxx: fix NPIV tear down process
scsi: sd_zbc: Fix sd_zbc_complete()
|
|
When a jump_whitelist bitmap is reused, it needs to be cleared.
Currently this is done with memset() and the size calculation assumes
bitmaps are made of 32-bit words, not longs. So on 64-bit
architectures, only the first half of the bitmap is cleared.
If some whitelist bits are carried over between successive batches
submitted on the same context, this will presumably allow embedding
the rogue instructions that we're trying to reject.
Use bitmap_zero() instead, which gets the calculation right.
Fixes: f8c08d8faee5 ("drm/i915/cmdparser: Add support for backward jumps")
Signed-off-by: Ben Hutchings <ben@decadent.org.uk>
Signed-off-by: Jon Bloomfield <jon.bloomfield@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC fixes from Olof Johansson:
"A set of fixes that have trickled in over the last couple of weeks:
- MAINTAINER update for Cavium/Marvell ThunderX2
- stm32 tweaks to pinmux for Joystick/Camera, and RAM allocation for
CAN interfaces
- i.MX fixes for voltage regulator GPIO mappings, fixes voltage
scaling issues
- More i.MX fixes for various issues on i.MX eval boards: interrupt
storm due to u-boot leaving pins in new states, fixing power button
config, a couple of compatible-string corrections.
- Powerdown and Suspend/Resume fixes for Allwinner A83-based tablets
- A few documentation tweaks and a fix of a memory leak in the reset
subsystem"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc:
MAINTAINERS: update Cavium ThunderX2 maintainers
ARM: dts: stm32: change joystick pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: remove OV5640 pinctrl definition on stm32mp157c-ev1
ARM: dts: stm32: Fix CAN RAM mapping on stm32mp157c
ARM: dts: stm32: relax qspi pins slew-rate for stm32mp157
arm64: dts: zii-ultra: fix ARM regulator GPIO handle
ARM: sunxi: Fix CPU powerdown on A83T
ARM: dts: sun8i-a83t-tbs-a711: Fix WiFi resume from suspend
arm64: dts: imx8mn: fix compatible string for sdma
arm64: dts: imx8mm: fix compatible string for sdma
reset: fix reset_control_ops kerneldoc comment
ARM: dts: imx6-logicpd: Re-enable SNVS power key
soc: imx: gpc: fix initialiser format
ARM: dts: imx6qdl-sabreauto: Fix storm of accelerometer interrupts
arm64: dts: ls1028a: fix a compatible issue
reset: fix reset_control_get_exclusive kerneldoc comment
reset: fix reset_control_lookup kerneldoc comment
reset: fix of_reset_control_get_count kerneldoc comment
reset: fix of_reset_simple_xlate kerneldoc comment
reset: Fix memory leak in reset_control_array_put()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull IIO fixes and staging driver from Greg KH:
"Here is a mix of a number of IIO driver fixes for 5.4-rc7, and a whole
new staging driver.
The IIO fixes resolve some reported issues, all are tiny.
The staging driver addition is the vboxsf filesystem, which is the
VirtualBox guest shared folder code. Hans has been trying to get
filesystem reviewers to review the code for many months now, and
Christoph finally said to just merge it in staging now as it is
stand-alone and the filesystem people can review it easier over time
that way.
I know it's late for this big of an addition, but it is stand-alone.
The code has been in linux-next for a while, long enough to pick up a
few tiny fixes for it already so people are looking at it.
All of these have been in linux-next with no reported issues"
* tag 'staging-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging:
staging: Fix error return code in vboxsf_fill_super()
staging: vboxsf: fix dereference of pointer dentry before it is null checked
staging: vboxsf: Remove unused including <linux/version.h>
staging: Add VirtualBox guest shared folder (vboxsf) support
iio: adc: stm32-adc: fix stopping dma
iio: imu: inv_mpu6050: fix no data on MPU6050
iio: srf04: fix wrong limitation in distance measuring
iio: imu: adis16480: make sure provided frequency is positive
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver fixes from Greg KH:
"Here are a number of late-arrival driver fixes for issues reported for
some char/misc drivers for 5.4-rc7
These all come from the different subsystem/driver maintainers as
things that they had reports for and wanted to see fixed.
All of these have been in linux-next with no reported issues"
* tag 'char-misc-5.4-rc7' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc:
intel_th: pci: Add Jasper Lake PCH support
intel_th: pci: Add Comet Lake PCH support
intel_th: msu: Fix possible memory leak in mode_store()
intel_th: msu: Fix overflow in shift of an unsigned int
intel_th: msu: Fix missing allocation failure check on a kstrndup
intel_th: msu: Fix an uninitialized mutex
intel_th: gth: Fix the window switching sequence
soundwire: slave: fix scanf format
soundwire: intel: fix intel_register_dai PDI offsets and numbers
interconnect: Add locking in icc_set_tag()
interconnect: qcom: Fix icc_onecell_data allocation
soundwire: depend on ACPI || OF
soundwire: depend on ACPI
thunderbolt: Drop unnecessary read when writing LC command in Ice Lake
thunderbolt: Fix lockdep circular locking depedency warning
thunderbolt: Read DP IN adapter first two dwords in one go
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull timer fixes from Thomas Gleixner:
"A small set of fixes for timekeepoing and clocksource drivers:
- VDSO data was updated conditional on the availability of a VDSO
capable clocksource. This causes the VDSO functions which do not
depend on a VDSO capable clocksource to operate on stale data.
Always update unconditionally.
- Prevent a double free in the mediatek driver
- Use the proper helper in the sh_mtu2 driver so it won't attempt to
initialize non-existing interrupts"
* 'timers-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
timekeeping/vsyscall: Update VDSO data unconditionally
clocksource/drivers/sh_mtu2: Do not loop using platform_get_irq_by_name()
clocksource/drivers/mediatek: Fix error handling
|
|
There is a race between driver code that does setup/cleanup of device
and devlink reload operation that in some drivers works with the same
code. Use after free could we easily obtained by running:
while true; do
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/bind
devlink dev reload pci/0000:00:10.0 &
echo "0000:00:10.0" >/sys/bus/pci/drivers/mlxsw_spectrum2/unbind
done
Fix this by enabling reload only after setup of device is complete and
disabling it at the beginning of the cleanup process.
Reported-by: Ido Schimmel <idosch@mellanox.com>
Fixes: 2d8dc5bbf4e7 ("devlink: Add support for reload")
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control fixes from Linus Walleij:
- Fix glitch risks in the Intel GPIO
- Fix the Intel Cherryview valid irq mask calculation.
- Allocate the Intel Cherryview irqchip dynamically.
- Fix the valid mask init sequency on the ST STMFX driver.
* tag 'pinctrl-v5.4-3' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl:
pinctrl: stmfx: fix valid_mask init sequence
pinctrl: cherryview: Allocate IRQ chip dynamic
pinctrl: cherryview: Fix irq_valid_mask calculation
pinctrl: intel: Avoid potential glitches if pin is in GPIO mode
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog fixes from Wim Van Sebroeck:
- cpwd: fix build regression
- pm8916_wdt: fix pretimeout registration flow
- meson: Fix the wrong value of left time
- imx_sc_wdt: Pretimeout should follow SCU firmware format
- bd70528: Add MODULE_ALIAS to allow module auto loading
* tag 'linux-watchdog-5.4-rc7' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: bd70528: Add MODULE_ALIAS to allow module auto loading
watchdog: imx_sc_wdt: Pretimeout should follow SCU firmware format
watchdog: meson: Fix the wrong value of left time
watchdog: pm8916_wdt: fix pretimeout registration flow
watchdog: cpwd: fix build regression
|
|
Pull networking fixes from David Miller:
1) BPF sample build fixes from Björn Töpel
2) Fix powerpc bpf tail call implementation, from Eric Dumazet.
3) DCCP leaks jiffies on the wire, fix also from Eric Dumazet.
4) Fix crash in ebtables when using dnat target, from Florian Westphal.
5) Fix port disable handling whne removing bcm_sf2 driver, from Florian
Fainelli.
6) Fix kTLS sk_msg trim on fallback to copy mode, from Jakub Kicinski.
7) Various KCSAN fixes all over the networking, from Eric Dumazet.
8) Memory leaks in mlx5 driver, from Alex Vesker.
9) SMC interface refcounting fix, from Ursula Braun.
10) TSO descriptor handling fixes in stmmac driver, from Jose Abreu.
11) Add a TX lock to synchonize the kTLS TX path properly with crypto
operations. From Jakub Kicinski.
12) Sock refcount during shutdown fix in vsock/virtio code, from Stefano
Garzarella.
13) Infinite loop in Intel ice driver, from Colin Ian King.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net: (108 commits)
ixgbe: need_wakeup flag might not be set for Tx
i40e: need_wakeup flag might not be set for Tx
igb/igc: use ktime accessors for skb->tstamp
i40e: Fix for ethtool -m issue on X722 NIC
iavf: initialize ITRN registers with correct values
ice: fix potential infinite loop because loop counter being too small
qede: fix NULL pointer deref in __qede_remove()
net: fix data-race in neigh_event_send()
vsock/virtio: fix sock refcnt holding during the shutdown
net: ethernet: octeon_mgmt: Account for second possible VLAN header
mac80211: fix station inactive_time shortly after boot
net/fq_impl: Switch to kvmalloc() for memory allocation
mac80211: fix ieee80211_txq_setup_flows() failure path
ipv4: Fix table id reference in fib_sync_down_addr
ipv6: fixes rt6_probe() and fib6_nh->last_probe init
net: hns: Fix the stray netpoll locks causing deadlock in NAPI path
net: usb: qmi_wwan: add support for DW5821e with eSIM support
CDC-NCM: handle incomplete transfer of MTU
nfc: netlink: fix double device reference drop
NFC: st21nfca: fix double free
...
|
|
Pull block fixes from Jens Axboe:
- Two NVMe device removal crash fixes, and a compat fixup for for an
ioctl that was introduced in this release (Anton, Charles, Max - via
Keith)
- Missing error path mutex unlock for drbd (Dan)
- cgroup writeback fixup on dead memcg (Tejun)
- blkcg online stats print fix (Tejun)
* tag 'for-linus-2019-11-08' of git://git.kernel.dk/linux-block:
cgroup,writeback: don't switch wbs immediately on dead wbs if the memcg is dead
block: drbd: remove a stray unlock in __drbd_send_protocol()
blkcg: make blkcg_print_stat() print stats only for online blkgs
nvme: change nvme_passthru_cmd64 to explicitly mark rsvd
nvme-multipath: fix crash in nvme_mpath_clear_ctrl_paths
nvme-rdma: fix a segmentation fault during module unload
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jkirsher/net-queue
Jeff Kirsher says:
====================
Intel Wired LAN Driver Fixes 2019-11-08
This series contains fixes to igb, igc, ixgbe, i40e, iavf and ice
drivers.
Colin Ian King fixes a potentially wrap-around counter in a for-loop.
Nick fixes the default ITR values for the iavf driver to 50 usecs
interval.
Arkadiusz fixes 'ethtool -m' for X722 devices where the correct value
cannot be obtained from the firmware, so add X722 to the check to ensure
the wrong value is not returned.
Jake fixes igb and igc drivers in their implementation of launch time
support by declaring skb->tstamp value as ktime_t instead of s64.
Magnus fixes ixgbe and i40e where the need_wakeup flag for transmit may
not be set for AF_XDP sockets that are only used to send packets.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
