| Age | Commit message (Collapse) | Author |
|---|
|
Loading a new mapping table, the dm-raid target's constructor
retrieves the volatile reshaping state from the raid superblocks.
When the new table is activated in a following resume, the actual
reshape position is retrieved. The reshape driven by the previous
mapping can already have finished on small and/or fast devices thus
updating raid superblocks about the new raid layout.
This causes the actual array state (e.g. stripe size reshape finished)
to be inconsistent with the one in the new mapping, causing hangs with
left behind devices.
This race does not occur with usual raid device sizes but with small
ones (e.g. those created by the lvm2 test suite).
Fix by no longer transferring stale/inconsistent raid_set state during
preresume.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
There's a XFS on dm-crypt deadlock, recursing back to itself due to the
crypto subsystems use of GFP_KERNEL, reported here:
https://bugzilla.kernel.org/show_bug.cgi?id=200835
* dm-crypt calls crypt_convert in xts mode
* init_crypt from xts.c calls kmalloc(GFP_KERNEL)
* kmalloc(GFP_KERNEL) recurses into the XFS filesystem, the filesystem
tries to submit some bios and wait for them, causing a deadlock
Fix this by updating both the DM crypt and integrity targets to no
longer use the CRYPTO_TFM_REQ_MAY_SLEEP flag, which will change the
crypto allocations from GFP_KERNEL to GFP_ATOMIC, therefore they can't
recurse into a filesystem. A GFP_ATOMIC allocation can fail, but
init_crypt() in xts.c handles the allocation failure gracefully - it
will fall back to preallocated buffer if the allocation fails.
The crypto API maintainer says that the crypto API only needs to
allocate memory when dealing with unaligned buffers and therefore
turning CRYPTO_TFM_REQ_MAY_SLEEP off is safe (see this discussion:
https://www.redhat.com/archives/dm-devel/2018-August/msg00195.html )
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Platform data pointer may be NULL. We check it everywhere but in one
place. Fix it.
Fixes: 8af70cd2ca50 ("memory: aemif: add support for board files")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Cc: stable@vger.kernel.org
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
https://github.com/Broadcom/stblinux into fixes
This pull request contains Broadcom ARM/ARM64 SoCs drivers fixes for
4.19, please pull the following:
- Peter adds an alias to the Raspberry Pi HWMON driver that was just
merged as part of the 4.19 merge window
* tag 'arm-soc/for-4.19/drivers-fixes' of https://github.com/Broadcom/stblinux:
hwmon: rpi: add module alias to raspberrypi-hwmon
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Firmware can provide zero as values for sustained performance level and
corresponding sustained frequency in kHz in order to hide the actual
frequencies and provide only abstract values. It may endup with divide
by zero scenario resulting in kernel panic.
Let's set the multiplication factor to one if either one or both of them
(sustained_perf_level and sustained_freq) are set to zero.
Fixes: a9e3fbfaa0ff ("firmware: arm_scmi: add initial support for performance protocol")
Reported-by: Ionela Voinescu <ionela.voinescu@arm.com>
Signed-off-by: Sudeep Holla <sudeep.holla@arm.com>
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds a new qed firmware with fixes and support for new features.
Fixes:
- Fix a rare case of device crash with iWARP, iSCSI or FCoE offload.
- Fix GRE tunneled traffic when iWARP offload is enabled.
- Fix RoCE failure in ib_send_bw when using inline data.
- Fix latency optimization flow for inline WQEs.
- BigBear 100G fix
RDMA:
- Reduce task context size.
- Application page sizes above 2GB support.
- Performance improvements.
ETH:
- Tenant DCB support.
- Replace RSS indirection table update interface.
Misc:
- Debug Tools changes.
Signed-off-by: Denis Bolotin <denis.bolotin@cavium.com>
Signed-off-by: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Raydium touchscreen triggers interrupt storm after system-wide suspend:
[ 179.085033] i2c_hid i2c-CUST0000:00: i2c_hid_get_input: incomplete report (58/65535)
According to Raydium, Windows driver does not reset the device after system
resume.
The HID over I2C spec does specify a reset should be used at intialization, but
it doesn't specify if reset is required for system suspend.
Tested this patch on other i2c-hid touchpanels I have and those touchpanels do
work after S3 without doing reset. If any regression happens to other
touchpanel vendors, we can use quirk for Raydium devices.
There's still one device uses I2C_HID_QUIRK_RESEND_REPORT_DESCR so keep it
there.
Cc: Aaron Ma <aaron.ma@canonical.com>
Cc: AceLan Kao <acelan.kao@canonical.com>
Signed-off-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@gmail.com>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
If parent_get class method is not supported by the OSDs, fall back to
the legacy class method and assume that the parent is in the default
(i.e. "") namespace. The "use the child's image namespace" workaround
is no longer needed because creating images within namespaces will
require parent_get aware OSDs.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
In preparation for the new parent_get and parent_overlap_get class
methods, factor out the fetching and decoding of parent data.
As a side effect, we now decode all four fields in the "no parent"
case.
Signed-off-by: Ilya Dryomov <idryomov@gmail.com>
Reviewed-by: Jason Dillaman <dillaman@redhat.com>
|
|
Commit 12864ff8545f (ACPI / LPSS: Avoid PM quirks on suspend and resume
from hibernation) bypasses lpss quirks for S3 and S4, by setting a flag
for S3/S4 in acpi_lpss_suspend(), and check that flag in
acpi_lpss_resume().
But this overlooks the boot case where acpi_lpss_resume() may get called
without a corresponding acpi_lpss_suspend() having been called.
Thus force setting the flag during boot.
Fixes: 12864ff8545f (ACPI / LPSS: Avoid PM quirks on suspend and resume from hibernation)
Link: https://bugzilla.kernel.org/show_bug.cgi?id=200989
Reported-and-tested-by: William Lieurance <william.lieurance@namikoda.com>
Signed-off-by: Zhang Rui <rui.zhang@intel.com>
Cc: 4.15+ <stable@vger.kernel.org> # 4.15+: 12864ff8545f (ACPI / LPSS: Avoid ...)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Calling dmi_check_system() early only works on X86. Other
architectures initialize the DMI subsystem later so it's not
ready yet when ACPI itself gets initialized.
In the best case it results in a useless call to a function which
will do nothing. But depending on the dmi implementation, it could
also result in warnings. Best is to not call the function when it
can't work and isn't needed.
Additionally, if anyone ever needs to add non-x86 quirks, it would
surprisingly not work, so document the limitation to avoid confusion.
Signed-off-by: Jean Delvare <jdelvare@suse.de>
Fixes: cce4f632db20 (ACPI: fix early DSDT dmi check warnings on ia64)
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/balbi/usb into usb-linus
Felipe writes:
usb: fixes for v4.19-rc2
NET2280 got a fix to an old patch attempting to fix locking for gadget
framework callbacks.
DWC2 fixed a bug where driver was attempting to access registers before
clocks were enabled.
DWC3 got a fix for ULPI clock configuration on Baytrail devices.
FOTG210 plugged a memory leak and Renesas USB3 fixed ep0 maxpacket size.
|
|
This patch makes some declaration more consistent.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adopt the SPDX license identifier headers to ease license compliance
management.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for this strcpy because alloc_etherdev() already
does this job.
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to bail out if lan78xx_get_endpoints() fails, otherwise the
result is overwritten.
Fixes: 55d7de9de6c3 ("Microchip's LAN7800 family USB 2/3 to 10/100/1000 Ethernet")
Signed-off-by: Stefan Wahren <stefan.wahren@i2se.com>
Reviewed-by: Raghuram Chary Jallipalli <raghuramchary.jallipalli@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VXLAN and GRE FW features have to currently be both advertised
for the driver to enable them. Separate the handling.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Dirk van der Merwe <dirk.vandermerwe@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the accesses to rtsyms now all going via special helpers
we can easily make sure the driver is not reading past the
end of the symbol.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For ease of debug preface all error messages with the name
of the symbol which caused them. Use the same message format
for existing messages while at it.
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Return the error and report value through the output param.
Fixes: 640917dd81b6 ("nfp: support access to absolute RTsyms")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
Reviewed-by: Francois H. Theron <francois.theron@netronome.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
net_failover_slave_unregister
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/net/net_failover.c: In function 'net_failover_slave_unregister':
drivers/net/net_failover.c:598:35: warning:
variable 'primary_dev' set but not used [-Wunused-but-set-variable]
There should check the validity of 'slave_dev'.
Fixes: cfc80d9a1163 ("net: Introduce net_failover driver")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sridhar Samudrala <sridhar.samudrala@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
CHECKSUM_COMPLETE is not applicable to SCTP protocol.
Setting it for SCTP packets leads to CRC32c validation failure.
Fixes: bbceefce9adf ("net/mlx5e: Support RX CHECKSUM_COMPLETE")
Signed-off-by: Alaa Hleihel <alaa@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In multi-host (MH) NIC scheme, a single HW port serves multiple hosts
or sockets on the same host.
The HW uses a mechanism in the PCIe buffer which monitors
the amount of consumed PCIe buffers per host.
On a certain configuration, under congestion,
the HW emulates a switch doing ECN marking on packets using ECN
indication on the completion descriptor (CQE).
The driver needs to set the ECN bits on the packet SKB,
such that the network stack can react on that, this commit does that.
Signed-off-by: Natali Shechtman <natali@mellanox.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Changed "priv.clock.lock" lock from 'rw_lock' to 'seq_lock'
in order to improve packet rate performance.
Tested on Intel(R) Xeon(R) CPU E5-2660 v2 @ 2.20GHz.
Sent 64b packets between two peers connected by ConnectX-5,
and measured packet rate for the receiver in three modes:
no time-stamping (base rate)
time-stamping using rw_lock (old lock) for critical region
time-stamping using seq_lock (new lock) for critical region
Only the receiver time stamped its packets.
The measured packet rate improvements are:
Single flow (multiple TX rings to single RX ring):
without timestamping: 4.26 (M packets)/sec
with rw-lock (old lock): 4.1 (M packets)/sec
with seq-lock (new lock): 4.16 (M packets)/sec
1.46% improvement
Multiple flows (multiple TX rings to six RX rings):
without timestamping: 22 (M packets)/sec
with rw-lock (old lock): 11.7 (M packets)/sec
with seq-lock (new lock): 21.3 (M packets)/sec
82.05% improvement
The packet rate improvement is due to the lack of atomic operations
for the 'readers' by the seq-lock.
Since there are much more 'readers' than 'writers' contention
on this lock, almost all atomic operations are saved.
this results in a dramatic decrease in overall
cache misses.
Signed-off-by: Shay Agroskin <shayag@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Not all profiles query the HW Q counters in update_stats() callback.
HW Q couners are limited per device and in case of representors all
their Q counters are allocated on the parent PF device.
Avoid reundant allocation of HW Q counters by moving the allocation
to init_rx profile callback.
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Move the definition of mlx5e_priv_flags into en_ethtool.c because it's
only used there.
Fixes: 4e59e2888139 ("net/mlx5e: Introduce net device priv flags infrastructure")
Signed-off-by: Kamal Heib <kamalheib1@gmail.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Previous patch in series changed flow counter storage structure from
rb_tree to linked list in order to improve flow counter traversal
performance. The drawback of such solution is that flow counter lookup by
id becomes linear in complexity.
Store pointers to flow counters in idr in order to improve lookup
performance to logarithmic again. Idr is non-intrusive data structure and
doesn't require extending flow counter struct with new elements. This means
that idr can be used for lookup, while linked list from previous patch is
used for traversal, and struct mlx5_fc size is <= 2 cache lines.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to improve performance of flow counter stats query loop that
traverses all configured flow counters, replace rb_tree with double-linked
list. This change improves performance of traversing flow counters by
removing the tree traversal. (profiling data showed that call to rb_next
was most top CPU consumer)
However, lookup of flow flow counter in list becomes linear, instead of
logarithmic. This problem is fixed by next patch in series, which adds idr
for fast lookup. Idr is to be used because it is not an intrusive data
structure and doesn't require adding any new members to struct mlx5_fc,
which allows its control data part to stay <= 1 cache line in size.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters is added to struct mlx5_fc_stats. Lockless
NULL-terminated single linked list data type is used due to following
reasons:
- This use case only needs to add single element to list and
remove/iterate whole list. Lockless list doesn't require any additional
synchronization for these operations.
- First cache line of flow counter data structure only has space to store
single additional pointer, which precludes usage of double linked list.
Remove flow counter 'deleted' flag that is no longer needed.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to prevent flow counters stats work function from traversing whole
flow counters tree while searching for deleted flow counters, new list to
store deleted flow counters will be added to struct mlx5_fc_stats. However,
the flow counter structure itself has no space left to store any more data
in first cache line. To free space that is needed to store additional list
node, convert current addlist double linked list (two pointers per node) to
atomic single linked list (one pointer per node).
Lockless NULL-terminated single linked list data type doesn't require any
additional external synchronization for operations used by flow counters
module (add single new element, remove all elements from list and traverse
them). Remove addlist_lock that is no longer needed.
Signed-off-by: Vlad Buslov <vladbu@mellanox.com>
Acked-by: Amir Vadai <amir@vadai.me>
Reviewed-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
GVT-g emualte the opregion for guest with bdb version as '186' which
child_device_config length should be '33'.
v2: split into 2 patch. 1st for issue fix, 2nd for code clean up.(Zhenyu)
v3: add fixes tag.(Zhenyu)
Fixes: 4023f301d28f ("drm/i915/gvt: opregion virtualization for win")
CC: Xiaolin Zhang <xiaolin.zhang@intel.com>
Reviewed-by: Xiaolin Zhang <xiaolin.zhang@intel.com>
Signed-off-by: Weinan Li <weinan.z.li@intel.com>
Signed-off-by: Zhenyu Wang <zhenyuw@linux.intel.com>
|
|
This is a false positive report due to incorrect nested lock
annotations as we lock multiple fgs with the same subclass.
Instead of locking all fgs only lock the one being used as was
done before.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Copy and paste bug was introduced in the offending patch.
We need to write udp source port value into the headers value and not
headers criteria "mask".
Fixes: 142644f8a1f8 ("net/mlx5e: Ethtool steering flow parsing refactoring")
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently, mlx5_attach_interface does not check for error
after calling intf->attach or intf->add. When these two calls
fails, the client is not initialized and will cause issues such as
kernel panic on invalid address in the teardown path (mlx5_detach_interface)
Fixes: 737a234bb638 ("net/mlx5: Introduce attach/detach to interface API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The PCI BDF is not unique. PCI domain must also be considered when
searching for the next physical device during lag setup. Example below:
mlx5_core 0000:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0000:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.0: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
mlx5_core 0001:01:00.1: MLX5E: StrdRq(1) RqSz(8) StrdSz(128) RxCqeCmprss(0)
Signed-off-by: Daniel Jurgens <danielj@mellanox.com>
Reviewed-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If building match list fg fails and we never jumped to
search_again_locked label then the function returned without
unlocking the read lock.
Fixes: bd71b08ec2ee ("net/mlx5: Support multiple updates of steering rules in parallel")
Signed-off-by: Roi Dayan <roid@mellanox.com>
Reviewed-by: Maor Gottlieb <maorg@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The memory allocated for the slow path table flow group input structure
was not freed upon successful return, fix that.
Fixes: 1967ce6ea5c8 ("net/mlx5: E-Switch, Refactor fast path FDB table creation in switchdev mode")
Signed-off-by: Raed Salem <raeds@mellanox.com>
Reviewed-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: d7037ad73daa ("net/mlx5: Fix QP fragmented buffer allocation")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Minimal stride size is 16.
Hence, the number of strides in a fragment (of PAGE_SIZE)
is <= PAGE_SIZE / 16 <= 4K.
u16 is sufficient to represent this.
Fixes: 388ca8be0037 ("IB/mlx5: Implement fragmented completion queue (CQ)")
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Reviewed-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When initializing the device (procedure init_one), the driver
calls mlx5_pci_init to perform pci initialization. As part of this
initialization, mlx5_pci_init creates a debugfs directory.
If this creation fails, init_one aborts, returning failure to
the caller (which is the probe method caller).
The main reason for such a failure to occur is if the debugfs
directory already exists. This can happen if the last time
mlx5_pci_close was called, debugfs_remove (silently) failed due
to the debugfs directory not being empty.
Guarantee that such a debugfs_remove failure will not occur by
instead calling debugfs_remove_recursive in procedure mlx5_pci_close.
Fixes: 59211bd3b632 ("net/mlx5: Split the load/unload flow into hardware and software flows")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When the mlx5 health mechanism detects a problem while the driver
is in the middle of init_one or remove_one, the driver needs to prevent
the health mechanism from scheduling future work; if future work
is scheduled, there is a problem with use-after-free: the system WQ
tries to run the work item (which has been freed) at the scheduled
future time.
Prevent this by disabling work item scheduling in the health mechanism
when the driver is in the middle of init_one() or remove_one().
Fixes: e126ba97dba9 ("mlx5: Add driver for Mellanox Connect-IB adapters")
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Reviewed-by: Feras Daoud <ferasda@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
If ib_uverbs_create_uapi() fails, dev_num should be freed from the bitmap.
Fixes: 7d96c9b17636 ("IB/uverbs: Have the core code create the uverbs_root_spec")
Signed-off-by: Parav Pandit <parav@mellanox.com>
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
1. DMA-able memory allocated for Shadow QP was not being freed.
2. bnxt_qplib_alloc_qp_hdr_buf() had a bug wherein the SQ pointer was
erroneously pointing to the RQ. But since the corresponding
free_qp_hdr_buf() was correct, memory being free was less than what was
allocated.
Fixes: 1ac5a4047975 ("RDMA/bnxt_re: Add bnxt_re RoCE driver")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
|
This is dead code because j can never be 1 at this point. We had
intended to just test if the bit was clear.
Fixes: bbd8decd4123 ("hwmon: (nct6775) Add support for weighted fan control")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Guenter Roeck <linux@roeck-us.net>
|
|
Inside of start_xmit() the call to check if the connection is up and the
queueing of the packets for later transmission is not atomic which leaves
a window where cm_rep_handler can run, set the connection up, dequeue
pending packets and leave the subsequently queued packets by start_xmit()
sitting on neigh->queue until they're dropped when the connection is torn
down. This only applies to connected mode. These dropped packets can
really upset TCP, for example, and cause multi-minute delays in
transmission for open connections.
Here's the code in start_xmit where we check to see if the connection is
up:
if (ipoib_cm_get(neigh)) {
if (ipoib_cm_up(neigh)) {
ipoib_cm_send(dev, skb, ipoib_cm_get(neigh));
goto unref;
}
}
The race occurs if cm_rep_handler execution occurs after the above
connection check (specifically if it gets to the point where it acquires
priv->lock to dequeue pending skb's) but before the below code snippet in
start_xmit where packets are queued.
if (skb_queue_len(&neigh->queue) < IPOIB_MAX_PATH_REC_QUEUE) {
push_pseudo_header(skb, phdr->hwaddr);
spin_lock_irqsave(&priv->lock, flags);
__skb_queue_tail(&neigh->queue, skb);
spin_unlock_irqrestore(&priv->lock, flags);
} else {
++dev->stats.tx_dropped;
dev_kfree_skb_any(skb);
}
The patch acquires the netif tx lock in cm_rep_handler for the section
where it sets the connection up and dequeues and retransmits deferred
skb's.
Fixes: 839fcaba355a ("IPoIB: Connected mode experimental support")
Cc: stable@vger.kernel.org
Signed-off-by: Aaron Knister <aaron.s.knister@nasa.gov>
Tested-by: Ira Weiny <ira.weiny@intel.com>
Reviewed-by: Ira Weiny <ira.weiny@intel.com>
Signed-off-by: Jason Gunthorpe <jgg@mellanox.com>
|
