| Age | Commit message (Collapse) | Author |
|---|
|
After commit 5d32a66541c4 ("PCI/ACPI: Allow ACPI to be built without
CONFIG_PCI set") dependencies on CONFIG_PCI that previously were
satisfied implicitly through dependencies on CONFIG_ACPI have to be
specified directly.
WARNING: unmet direct dependencies detected for I2C_DESIGNWARE_PLATFORM
Depends on [n]: I2C [=y] && HAS_IOMEM [=y] && (ACPI [=y] && COMMON_CLK [=n] || !ACPI [=y])
Selected by [y]:
- MFD_TPS68470 [=y] && HAS_IOMEM [=y] && ACPI [=y] && I2C [=y]=y
MFD_TPS68470 is an ACPI only device and selects I2C_DESIGNWARE_PLATFORM.
I2C_DESIGNWARE_PLATFORM does not have any configuration today for ACPI
support without CONFIG_PCI set.
For sake of a quick fix this introduces a new mandatory dependency to
the driver which may survive without it. Otherwise we need to revisit
the driver architecture to address this properly.
Fixes: 5d32a66541c46 ("PCI/ACPI: Allow ACPI to be built without CONFIG_PCI set")
Signed-off-by: Sinan Kaya <okaya@kernel.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
dev_consume_skb_irq() should be called in cpmac_end_xmit() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in bmac_txdma_intr() when
xmit done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in amd8111e_tx() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in ace_tx_int() when xmit
done. It makes drop profiles more friendly.
Signed-off-by: Yang Wei <yang.wei9@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After batched used ring updating was introduced in commit e2b3b35eb989
("vhost_net: batch used ring update in rx"). We tend to batch heads in
vq->heads for more than one packet. But the quota passed to
get_rx_bufs() was not correctly limited, which can result a OOB write
in vq->heads.
headcount = get_rx_bufs(vq, vq->heads + nvq->done_idx,
vhost_len, &in, vq_log, &log,
likely(mergeable) ? UIO_MAXIOV : 1);
UIO_MAXIOV was still used which is wrong since we could have batched
used in vq->heads, this will cause OOB if the next buffer needs more
than 960 (1024 (UIO_MAXIOV) - 64 (VHOST_NET_BATCH)) heads after we've
batched 64 (VHOST_NET_BATCH) heads:
Acked-by: Stefan Hajnoczi <stefanha@redhat.com>
=============================================================================
BUG kmalloc-8k (Tainted: G B ): Redzone overwritten
-----------------------------------------------------------------------------
INFO: 0x00000000fd93b7a2-0x00000000f0713384. First byte 0xa9 instead of 0xcc
INFO: Allocated in alloc_pd+0x22/0x60 age=3933677 cpu=2 pid=2674
kmem_cache_alloc_trace+0xbb/0x140
alloc_pd+0x22/0x60
gen8_ppgtt_create+0x11d/0x5f0
i915_ppgtt_create+0x16/0x80
i915_gem_create_context+0x248/0x390
i915_gem_context_create_ioctl+0x4b/0xe0
drm_ioctl_kernel+0xa5/0xf0
drm_ioctl+0x2ed/0x3a0
do_vfs_ioctl+0x9f/0x620
ksys_ioctl+0x6b/0x80
__x64_sys_ioctl+0x11/0x20
do_syscall_64+0x43/0xf0
entry_SYSCALL_64_after_hwframe+0x44/0xa9
INFO: Slab 0x00000000d13e87af objects=3 used=3 fp=0x (null) flags=0x200000000010201
INFO: Object 0x0000000003278802 @offset=17064 fp=0x00000000e2e6652b
Fixing this by allocating UIO_MAXIOV + VHOST_NET_BATCH iovs for
vhost-net. This is done through set the limitation through
vhost_dev_init(), then set_owner can allocate the number of iov in a
per device manner.
This fixes CVE-2018-16880.
Fixes: e2b3b35eb989 ("vhost_net: batch used ring update in rx")
Signed-off-by: Jason Wang <jasowang@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "hostdata->dev" pointer is NULL here. We set "hostdata->dev = dev;"
later in the function and we also use "hostdata->dev" when we call
dma_free_attrs() in NCR_700_release().
This bug predates git version control.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
There are two issues here. First if cmgr->hba is not set early enough then
it leads to a NULL dereference. Second if we don't completely initialize
cmgr->io_bdt_pool[] then we end up dereferencing uninitialized pointers.
Fixes: 853e2bd2103a ("[SCSI] bnx2fc: Broadcom FCoE offload driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The WRITE SAME(10) and (16) implementations didn't take account of the
buffer wrap required when the virtual_gb parameter is greater than 0.
Fix that and rename the fake_store() function to lba2fake_store() to lessen
confusion with the global fake_storep pointer. Bump version date.
Signed-off-by: Douglas Gilbert <dgilbert@interlog.com>
Reported-by: Bart Van Assche <bvanassche@acm.org>
Tested by: Bart Van Assche <bvanassche@acm.org>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
The issue to be fixed in this commit is when libfc found it received a
invalid FLOGI response from FC switch, it would return without freeing the
fc frame, which is just the skb data. This would cause memory leak if FC
switch keeps sending invalid FLOGI responses.
This fix is just to make it execute `fc_frame_free(fp)` before returning
from function `fc_lport_flogi_resp`.
Signed-off-by: Ming Lu <ming.lu@citrix.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Since v2.6.35 commit 683229845f17 ("[SCSI] zfcp: Report scatter-gather
limits to SCSI and block layer"), zfcp set dma_parms.max_segment_size ==
PAGE_SIZE (but without using the setter dma_set_max_seg_size()) and
scsi_host_template.dma_boundary == PAGE_SIZE - 1.
v5.0-rc1 commit 50c2e9107f17 ("scsi: introduce a max_segment_size
host_template parameters") introduced a new field
scsi_host_template.max_segment_size. If an LLDD such as zfcp does not set
it, scsi_host_alloc() uses BLK_MAX_SEGMENT_SIZE = 65536 for
Scsi_Host.max_segment_size. __scsi_init_queue() announced the minimum of
Scsi_Host.max_segment_size and dma_parms.max_segment_size to the block
layer. For zfcp: min(65536, 4096) == 4096 which was still good.
v5.0 commit a8cf59a6692c ("scsi: communicate max segment size to the DMA
mapping code") announces Scsi_Host.max_segment_size to the block layer and
overwrites dma_parms.max_segment_size with Scsi_Host.max_segment_size. For
zfcp dma_parms.max_segment_size == Scsi_Host.max_segment_size == 65536
which is also reflected in block queue limits.
$ cd /sys/bus/ccw/drivers/zfcp
$ cd 0.0.3c40/host5/rport-5:0-4/target5:0:4/5:0:4:10/block/sdi/queue
$ cat max_segment_size
65536
Zfcp I/O still works because dma_boundary implicitly still keeps the
effective max segment size <= PAGE_SIZE. However, dma_boundary does not
seem visible to user space, but max_segment_size is visible and shows a
misleading wrong value. Fix it and inherit the stable tag of a8cf59a6692c.
Devices on our bus ccw support DMA but no DMA mapping. Of multiple device
types on the ccw bus, only zfcp needs dma_parms for SCSI limits. So, leave
dma_parms setup in zfcp and do not move it to the bus.
Signed-off-by: Steffen Maier <maier@linux.ibm.com>
Fixes: 50c2e9107f ("scsi: introduce a max_segment_size host_template parameters")
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
This fixes the case when md array assembly fails because of raid cache recovery
unable to allocate a stripe, despite attempts to replay stripes and increase
cache size. This happens because stripes released by r5c_recovery_replay_stripes
and raid5_set_cache_size don't become available for allocation immediately.
Released stripes first are placed on conf->released_stripes list and require
md thread to merge them on conf->inactive_list before they can be allocated.
Patch allows final allocation attempt during cache recovery to wait for
new stripes to become availabe for allocation.
Cc: linux-raid@vger.kernel.org
Cc: Shaohua Li <shli@kernel.org>
Cc: linux-stable <stable@vger.kernel.org> # 4.10+
Fixes: b4c625c67362 ("md/r5cache: r5cache recovery: part 1")
Signed-off-by: Alexei Naberezhnov <anaberezhnov@fb.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
|
|
KASAN reported following bug in qed_init_qm_get_idx_from_flags
due to inappropriate casting of "pq_flags". Fix the type of "pq_flags".
[ 196.624707] BUG: KASAN: stack-out-of-bounds in qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed]
[ 196.624712] Read of size 8 at addr ffff809b00bc7360 by task kworker/0:9/1712
[ 196.624714]
[ 196.624720] CPU: 0 PID: 1712 Comm: kworker/0:9 Not tainted 4.18.0-60.el8.aarch64+debug #1
[ 196.624723] Hardware name: To be filled by O.E.M. Saber/Saber, BIOS 0ACKL024 09/26/2018
[ 196.624733] Workqueue: events work_for_cpu_fn
[ 196.624738] Call trace:
[ 196.624742] dump_backtrace+0x0/0x2f8
[ 196.624745] show_stack+0x24/0x30
[ 196.624749] dump_stack+0xe0/0x11c
[ 196.624755] print_address_description+0x68/0x260
[ 196.624759] kasan_report+0x178/0x340
[ 196.624762] __asan_report_load_n_noabort+0x38/0x48
[ 196.624786] qed_init_qm_get_idx_from_flags+0x1a4/0x1b8 [qed]
[ 196.624808] qed_init_qm_info+0xec0/0x2200 [qed]
[ 196.624830] qed_resc_alloc+0x284/0x7e8 [qed]
[ 196.624853] qed_slowpath_start+0x6cc/0x1ae8 [qed]
[ 196.624864] __qede_probe.isra.10+0x1cc/0x12c0 [qede]
[ 196.624874] qede_probe+0x78/0xf0 [qede]
[ 196.624879] local_pci_probe+0xc4/0x180
[ 196.624882] work_for_cpu_fn+0x54/0x98
[ 196.624885] process_one_work+0x758/0x1900
[ 196.624888] worker_thread+0x4e0/0xd18
[ 196.624892] kthread+0x2c8/0x350
[ 196.624897] ret_from_fork+0x10/0x18
[ 196.624899]
[ 196.624902] Allocated by task 2:
[ 196.624906] kasan_kmalloc.part.1+0x40/0x108
[ 196.624909] kasan_kmalloc+0xb4/0xc8
[ 196.624913] kasan_slab_alloc+0x14/0x20
[ 196.624916] kmem_cache_alloc_node+0x1dc/0x480
[ 196.624921] copy_process.isra.1.part.2+0x1d8/0x4a98
[ 196.624924] _do_fork+0x150/0xfa0
[ 196.624926] kernel_thread+0x48/0x58
[ 196.624930] kthreadd+0x3a4/0x5a0
[ 196.624932] ret_from_fork+0x10/0x18
[ 196.624934]
[ 196.624937] Freed by task 0:
[ 196.624938] (stack is not available)
[ 196.624940]
[ 196.624943] The buggy address belongs to the object at ffff809b00bc0000
[ 196.624943] which belongs to the cache thread_stack of size 32768
[ 196.624946] The buggy address is located 29536 bytes inside of
[ 196.624946] 32768-byte region [ffff809b00bc0000, ffff809b00bc8000)
[ 196.624948] The buggy address belongs to the page:
[ 196.624952] page:ffff7fe026c02e00 count:1 mapcount:0 mapping:ffff809b4001c000 index:0x0 compound_mapcount: 0
[ 196.624960] flags: 0xfffff8000008100(slab|head)
[ 196.624967] raw: 0fffff8000008100 dead000000000100 dead000000000200 ffff809b4001c000
[ 196.624970] raw: 0000000000000000 0000000000080008 00000001ffffffff 0000000000000000
[ 196.624973] page dumped because: kasan: bad access detected
[ 196.624974]
[ 196.624976] Memory state around the buggy address:
[ 196.624980] ffff809b00bc7200: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 196.624983] ffff809b00bc7280: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 196.624985] >ffff809b00bc7300: 00 00 00 00 00 00 00 00 f1 f1 f1 f1 04 f2 f2 f2
[ 196.624988] ^
[ 196.624990] ffff809b00bc7380: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 196.624993] ffff809b00bc7400: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
[ 196.624995] ==================================================================
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cache number of fragments in the skb locally as in case
of linear skb (with zero fragments), tx completion
(or freeing of skb) may happen before driver tries
to get number of frgaments from the skb which could
lead to stale access to an already freed skb.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VFs may hit VF-PF channel timeout while probing, as in some
cases it was observed that VF FLR and VF "acquire" message
transaction (i.e first message from VF to PF in VF's probe flow)
could occur simultaneously which could lead VF to fail sending
"acquire" message to PF as VF is marked disabled from HW perspective
due to FLR, which will result into channel timeout and VF probe failure.
In such cases, try retrying VF "acquire" message so that in later
attempts it could be successful to pass message to PF after the VF
FLR is completed and can be probed successfully.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF is always configured to drop control frames
(with reserved mac addresses) but to work LACP
on the VFs, it would require LACP control frames
to be forwarded or transmitted successfully.
This patch fixes this in such a way that trusted VFs
(marked through ndo_set_vf_trust) would be allowed to
pass the control frames such as LACP pdus.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When running tx switched traffic between VNICs
created via a bridge(to which VFs are added),
adapter drops the unicast packets in tx flow due to
VNIC's ucast mac being unknown to it. But VF interfaces
being in promiscuous mode should have caused adapter
to accept all the unknown ucast packets. Later, it
was found that driver doesn't really configure tx
promiscuous mode settings to accept all unknown unicast macs.
This patch fixes tx promiscuous mode settings to accept all
unknown/unmatched unicast macs and works out the scenario.
Signed-off-by: Manish Chopra <manishc@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dev_consume_skb_irq() should be called in i596_interrupt() when skb
xmit done. It makes drop profiles(dropwatch, perf) more friendly.
Signed-off-by: Yang Wei <albin_yang@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. In current implementation, every VLPI will temporarily be mapped to
the first CPU in system (normally CPU0) and then moved to the real
scheduled CPU later.
2. So there is a time window and a VLPI may be sent to CPU0 instead of
the real scheduled vCPU, in a multi-CPU virtual machine.
3. However, CPU0 may have not been scheduled as a virtual CPU after
system boots up, so the value of its GICR_VPROPBASER is unknown at
that moment.
4. If the INTID of VLPI is larger than 2^(GICR_VPROPBASER.IDbits+1),
while IDbits is also in unknown state, GIC will behave as if the VLPI
is out of range and simply drop it, which results in interrupt missing
in Guest.
As no code will clear GICR_VPROPBASER at runtime, we can safely
initialize the IDbits field at boot time for each CPU to get rid of
this issue.
We also clear Valid bit of GICR_VPENDBASER in case any ancient
programming gets left in and causes memory corrupting. A new function
its_clear_vpend_valid() is added to reuse the code in
its_vpe_deschedule().
Fixes: e643d8034036 ("irqchip/gic-v3-its: Add VPE scheduling")
Signed-off-by: Heyi Guo <guoheyi@huawei.com>
Signed-off-by: Heyi Guo <heyi.guo@linaro.org>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
On SoC reset all GPIO interrupts are disable. However, if kexec is
used to boot into a new kernel, the SoC does not experience a
reset. Hence GPIO interrupts can be left enabled from the previous
kernel. It is then possible for the interrupt to fire before an
interrupt handler is registered, resulting in the kernel complaining
of an "unexpected IRQ trap", the interrupt is never cleared, and so
fires again, resulting in an interrupt storm.
Disable all GPIO interrupts before registering the GPIO IRQ chip.
Fixes: 7f2691a19627 ("gpio: vf610: add gpiolib/IRQ chip driver for Vybrid")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
The checker complains during build
gpiolib-acpi.c:45: warning: Function parameter or member 'irq_requested' not described in 'acpi_gpio_event'
because the typo in the field description.
Fix the name to have documentation up-to-date.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some TQ-Systems ComExpress modules contain an IO controller with 8
GPIO lines.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Add missing '*' char to the start of the comment lines.
Signed-off-by: Phil Reid <preid@electromag.com.au>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
power off the phy should be done before populate the phy. Otherwise,
am335x_init() could be called by the phy owner to power on the phy first,
then am335x_phy_probe() turns off the phy again without the caller knowing
it.
Fixes: 2fc711d76352 ("usb: phy: am335x: Enable USB remote wakeup using PHY wakeup")
Cc: stable@vger.kernel.org # v3.18+
Signed-off-by: Bin Liu <b-liu@ti.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
If clk_prepare_enable() fails in dwc3_exynos_probe() or in
dwc3_exynos_resume(), exynos->clks[0] is left undisabled
because of usage preincrement in while condition.
Found by Linux Driver Verification project (linuxtesting.org).
Fixes: 9f2168367a0a ("usb: dwc3: exynos: Rework clock handling and prepare for new variants")
Acked-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
Fix link errors when CONFIG_FSL_USB2_OTG is enabled and USB_OTG_FSM is
set to module then the following link error occurs.
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_ioctl':
drivers/usb/phy/phy-fsl-usb.c:1083: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:1083:(.text+0x574): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_srp':
drivers/usb/phy/phy-fsl-usb.c:674: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:674:(.text+0x61c): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_host':
drivers/usb/phy/phy-fsl-usb.c:593: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:593:(.text+0x7a4): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_start_hnp':
drivers/usb/phy/phy-fsl-usb.c:695: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:695:(.text+0x858): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `a_wait_enum':
drivers/usb/phy/phy-fsl-usb.c:274: undefined reference to `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.c:274:(.text+0x16f0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o:drivers/usb/phy/phy-fsl-usb.c:619: more undefined references to `otg_statemachine' follow
aarch64-linux-gnu-ld: drivers/usb/phy/phy-fsl-usb.o: in function `fsl_otg_set_peripheral':
drivers/usb/phy/phy-fsl-usb.c:619:(.text+0x1fa0): relocation truncated to fit: R_AARCH64_CALL26 against undefined symbol `otg_statemachine'
make[1]: *** [Makefile:1020: vmlinux] Error 1
make[1]: Target 'Image' not remade because of errors.
make: *** [Makefile:152: sub-make] Error 2
make: Target 'Image' not remade because of errors.
Rework so that FSL_USB2_OTG depends on that the USB_OTG_FSM is builtin.
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
(!x & y) strikes again.
Fix bitwise and boolean operations by enclosing the expression:
intcsr & (1 << NET2272_PCI_IRQ)
in parentheses, before applying the boolean operator '!'.
Notice that this code has been there since 2011. So, it would
be helpful if someone can double-check this.
This issue was detected with the help of Coccinelle.
Fixes: ceb80363b2ec ("USB: net2272: driver for PLX NET2272 USB device controller")
Cc: stable@vger.kernel.org
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
For OUT endpoints, zero-length transfers require MaxPacketSize buffer as
per the DWC_usb3 programming guide 3.30a section 4.2.3.3.
This patch fixes this by explicitly checking zero length
transfer to correctly pad up to MaxPacketSize.
Fixes: c6267a51639b ("usb: dwc3: gadget: align transfers to wMaxPacketSize")
Cc: stable@vger.kernel.org
Signed-off-by: Tejas Joglekar <joglekar@synopsys.com>
Signed-off-by: Felipe Balbi <felipe.balbi@linux.intel.com>
|
|
to set cmd internal delay, need set PAD_TUNE register but not PAD_CMD_TUNE
register.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Fixes: 1ede5cb88a29 ("mmc: mediatek: Use data tune for CMD line tune")
Cc: stable@vger.kernel.org # v4.12+
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The BCM2835 MMC host driver requests a DMA channel on probe but neglects
to release the channel in the probe error path. The channel may
therefore be leaked, in particular if devm_clk_get() causes probe
deferral. Fix it.
Fixes: 660fc733bd74 ("mmc: bcm2835: Add new driver for the sdhost controller.")
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: stable@vger.kernel.org # v4.12+
Cc: Frank Pavlic <f.pavlic@kunbus.de>
Tested-by: Stefan Wahren <stefan.wahren@i2se.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Duec to a typo, mv88e6390_serdes_irq_setup() calls itself, rather than
mv88e6390x_serdes_irq_setup(). It then blows the stack, and shortly
after the machine blows up.
Fixes: 2defda1f4b91 ("net: dsa: mv88e6xxx: Add support for SERDES on ports 2-8 for 6390X")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If phy_power_on() fails in rk_gmac_powerup(), clocks are left enabled.
Found by Linux Driver Verification project (linuxtesting.org).
Signed-off-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When reading phy registers via Clause 45 MDIO protocol, after write
address operation, the driver use another write address operation, so
can not read the right value of any phy registers. This patch fixes it.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The hns driver of earlier devices, when autoneg off, restart autoneg
will return -EINVAL, so make the hns driver for the latest devices
do the same.
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In hns enet driver, we use of_parse_handle() to get hold of the
device node related to "ae-handle" but we have missed to put
the node reference using of_node_put() after we are done using
the node. This patch fixes it.
Note:
This problem is stated in Link: https://lkml.org/lkml/2018/12/22/217
Fixes: 48189d6aaf1e ("net: hns: enet specifies a reference to dsaf")
Reported-by: Alexey Khoroshilov <khoroshilov@ispras.ru>
Signed-off-by: Yonglong Liu <liuyonglong@huawei.com>
Signed-off-by: Peng Li <lipeng321@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull irq fixes from Thomas Gleixner:
"A small set of fixes for the interrupt subsystem:
- Fix a double increment in the irq descriptor allocator which
resulted in a sanity check only being done for every second
affinity mask
- Add a missing device tree translation in the stm32-exti driver.
Without that the interrupt association is completely wrong.
- Initialize the mutex in the GIC-V3 MBI driver
- Fix the alignment for aliasing devices in the GIC-V3-ITS driver so
multi MSI allocations work correctly
- Ensure that the initial affinity of a interrupt is not empty at
startup time.
- Drop bogus include in the madera irq chip driver
- Fix KernelDoc regression"
* 'irq-urgent-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
irqchip/gic-v3-its: Align PCI Multi-MSI allocation on their size
genirq/irqdesc: Fix double increment in alloc_descs()
genirq: Fix the kerneldoc comment for struct irq_affinity_desc
irqchip/madera: Drop GPIO includes
irqchip/gic-v3-mbi: Fix uninitialized mbi_lock
irqchip/stm32-exti: Add domain translate function
genirq: Make sure the initial affinity is not empty
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2019-01-25
This series introduces some fixes to mlx5 driver.
For more information please see tag log below.
Please pull and let me know if there is any problem.
For -stable v4.13
('net/mlx5e: Allow MAC invalidation while spoofchk is ON')
For -stable v4.18
('Revert "net/mlx5e: E-Switch, Initialize eswitch only if eswitch manager"')
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp
Pull EDAC fix from Borislav Petkov:
"Fix persistent register offsets of altera_edac, from Thor Thayer"
* tag 'edac_fix_for_5.0' of git://git.kernel.org/pub/scm/linux/kernel/git/bp/bp:
EDAC, altera: Fix S10 persistent register offset
|
|
If fill_level was not zero and status was not BUSY,
result of "tx_prod - tx_cons - inuse" might be zero.
Subtracting 1 unconditionally results invalid negative return value
on this case.
Make sure not to return an negative value.
Signed-off-by: Tomonori Sakita <tomonori.sakita@sord.co.jp>
Signed-off-by: Atsushi Nemoto <atsushi.nemoto@sord.co.jp>
Reviewed-by: Dalon L Westergreen <dalon.westergreen@linux.intel.com>
Acked-by: Thor Thayer <thor.thayer@linux.intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull dma-mapping fix from Christoph Hellwig:
"Fix a xen-swiotlb regression on arm64"
* tag 'dma-mapping-5.0-2' of git://git.infradead.org/users/hch/dma-mapping:
arm64/xen: fix xen-swiotlb cache flushing
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"A fix for namespace label support for non-Intel NVDIMMs that implement
the ACPI standard label method.
This has apparently never worked and could wait for v5.1. However it
has enough visibility with hardware vendors [1] and distro bug
trackers [2], and low enough risk that I decided it should go in for
-rc4. The other fixups target the new, for v5.0, nvdimm security
functionality. The larger init path fixup closes a memory leak and a
potential userspace lockup due to missed notifications.
[1] https://github.com/pmem/ndctl/issues/78
[2] https://bugs.launchpad.net/ubuntu/+source/linux/+bug/1811785
These have all soaked in -next for a week with no reported issues.
Summary:
- Fix support for NVDIMMs that implement the ACPI standard label
methods.
- Fix error handling for security overwrite (memory leak / userspace
hang condition), and another one-line security cleanup"
* tag 'libnvdimm-fixes-5.0-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
acpi/nfit: Fix command-supported detection
acpi/nfit: Block function zero DSMs
libnvdimm/security: Require nvdimm_security_setup_events() to succeed
nfit_test: fix security state pull for nvdimm security nfit_test
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input fixes from Dmitry Torokhov:
"A fixup for the input_event fix for y2038 Sparc64, and couple other
minor fixes"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: input_event - fix the CONFIG_SPARC64 mixup
Input: olpc_apsp - assign priv->dev earlier
Input: uinput - fix undefined behavior in uinput_validate_absinfo()
Input: raspberrypi-ts - fix link error
Input: xpad - add support for SteelSeries Stratus Duo
Input: input_event - provide override for sparc64
|
|
Pull networking fixes from David Miller:
1) Count ttl-dropped frames properly in mac80211, from Bob Copeland.
2) Integer overflow in ktime handling of bcm can code, from Oliver
Hartkopp.
3) Fix RX desc handling wrt. hw checksumming in ravb, from Simon
Horman.
4) Various hash key fixes in hv_netvsc, from Haiyang Zhang.
5) Use after free in ax25, from Eric Dumazet.
6) Several fixes to the SSN support in SCTP, from Xin Long.
7) Do not process frames after a NAPI reschedule in ibmveth, from
Thomas Falcon.
8) Fix NLA_POLICY_NESTED arguments, from Johannes Berg.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (42 commits)
qed: Revert error handling changes.
cfg80211: extend range deviation for DMG
cfg80211: reg: remove warn_on for a normal case
mac80211: Add attribute aligned(2) to struct 'action'
mac80211: don't initiate TDLS connection if station is not associated to AP
nl80211: fix NLA_POLICY_NESTED() arguments
ibmveth: Do not process frames after calling napi_reschedule
net: dev_is_mac_header_xmit() true for ARPHRD_RAWIP
net: usb: asix: ax88772_bind return error when hw_reset fail
MAINTAINERS: Update cavium networking drivers
net/mlx4_core: Fix error handling when initializing CQ bufs in the driver
net/mlx4_core: Add masking for a few queries on HCA caps
sctp: set flow sport from saddr only when it's 0
sctp: set chunk transport correctly when it's a new asoc
sctp: improve the events for sctp stream adding
sctp: improve the events for sctp stream reset
ip_tunnel: Make none-tunnel-dst tunnel port work with lwtunnel
ax25: fix possible use-after-free
sfc: suppress duplicate nvmem partition types in efx_ef10_mtd_probe
hv_netvsc: fix typos in code comments
...
|
|
Pull VFIO fixes from Alex Williamson:
- cleanup licenses in new files (Thomas Gleixner)
- cleanup new compiler warnings (Alexey Kardashevskiy)
* tag 'vfio-v5.0-rc4' of git://github.com/awilliam/linux-vfio:
vfio-pci/nvlink2: Fix ancient gcc warnings
vfio/pci: Cleanup license mess
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi
Pull SCSI fixes from James Bottomley:
"Six fixes, all of which appear to have user visible consequences.
The DMA one is a regression fix from the merge window and of the
others, four are driver specific and one specific to the target code"
* tag 'scsi-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/jejb/scsi:
scsi: ufs: Use explicit access size in ufshcd_dump_regs
scsi: tcmu: fix use after free
scsi: csiostor: fix NULL pointer dereference in csio_vport_set_state()
scsi: lpfc: nvmet: avoid hang / use-after-free when destroying targetport
scsi: lpfc: nvme: avoid hang / use-after-free when destroying localport
scsi: communicate max segment size to the DMA mapping code
|
|
Pull block fixes from Jens Axboe:
"A collection of fixes for this release. This contains:
- Silence sparse rightfully complaining about non-static wbt
functions (Bart)
- Fixes for the zoned comments/ioctl documentation (Damien)
- direct-io fix that's been lingering for a while (Ernesto)
- cgroup writeback fix (Tejun)
- Set of NVMe patches for nvme-rdma/tcp (Sagi, Hannes, Raju)
- Block recursion tracking fix (Ming)
- Fix debugfs command flag naming for a few flags (Jianchao)"
* tag 'for-linus-20190125' of git://git.kernel.dk/linux-block:
block: Fix comment typo
uapi: fix ioctl documentation
blk-wbt: Declare local functions static
blk-mq: fix the cmd_flag_name array
nvme-multipath: drop optimization for static ANA group IDs
nvmet-rdma: fix null dereference under heavy load
nvme-rdma: rework queue maps handling
nvme-tcp: fix timeout handler
nvme-rdma: fix timeout handler
writeback: synchronize sync(2) against cgroup writeback membership switches
block: cover another queue enter recursion via BIO_QUEUE_ENTERED
direct-io: allow direct writes to empty inodes
|
|
In dw_i3c_master_irq_handler(), we already have gotten
&master->xferqueue.lock, if we try to get the same lock again in
dw_i3c_master_dequeue_xfer(), deadlock happens.
We fix this issue by introduing dw_i3c_master_dequeue_xfer_locked()
which does all what dw_i3c_master_dequeue_xfer() does without trying
to lock &master->xferqueue.lock.
Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Acked-by: Vitor Soares <vitor.soares@synopsys.com>
Signed-off-by: Boris Brezillon <bbrezillon@kernel.org>
|
|
xtensa_irq_mask and xtensa_irq_unmask don't do the right thing when
called for the first two external IRQs. Treat these IRQs as per-CPU
IRQs.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
XEA2 and MX PIC can only retrigger software interrupts. Issue a warning
if an interrupt of any other type is retriggered.
Signed-off-by: Max Filippov <jcmvbkbc@gmail.com>
|
|
This is new code and not bug fixes.
This reverts all changes added by merge commit
8fb18be93efd7292d6ee403b9f61af1008239639
Signed-off-by: David S. Miller <davem@davemloft.net>
|
