| Age | Commit message (Collapse) | Author |
|---|
|
This commit adds a simple driver for the Marvell GICP, a hardware unit
that converts memory writes into GIC SPI interrupts. The driver provides
a number of functions to the ICU driver to allocate GICP interrupts, and
get the physical addresses that the ICUs should write to to set/clear
interrupts.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Reviewed-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Marc Zyngier <marc.zyngier@arm.com>
|
|
Add code comment to make it clear that the fall-through is intentional
and, OR ret with its previous value to avoid overwriting it so that
callers can check the correct return value.
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Cc: Qiuxu Zhuo <qiuxu.zhuo@intel.com>
Cc: Tony Luck <tony.luck@intel.com>
Cc: linux-edac <linux-edac@vger.kernel.org>
Link: http://lkml.kernel.org/r/20170622220535.GA4896@embeddedgus
[ Massage a bit. ]
Signed-off-by: Borislav Petkov <bp@suse.de>
|
|
The F54 driver is currently only using the first 6 bytes of F54 so there is
no need to read all 27 bytes. Some Dell systems (Dell XP13 9333 and
similar) have an issue with the touchpad or I2C bus when reading reports
larger then 16 bytes. Reads larger then 16 bytes are reported in two HID
reports. Something about the back to back reports seems to cause the next
read to report incorrect data. This results in F30 failing to load and the
click button failing to work.
Previous issues with the I2C controller or touchpad were addressed in:
commit 5b65c2a02966 ("HID: rmi: check sanity of the incoming report")
Fixes: https://bugzilla.kernel.org/show_bug.cgi?id=195949
Signed-off-by: Andrew Duggan <aduggan@synaptics.com>
Reviewed-by: Benjamin Tissoires <benjamin.tissoires@redhat.com>
Reviewed-by: Nick Dyer <nick@shmanahar.org>
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
Add combined gpio and pin controller driver for Renesas RZ/A1
r7s72100 SoC.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
A previous set of patches "cxl: Add support for Coherent Accelerator
Interface Architecture 2.0" has introduced a new support for the CAPI
cards. These patches have been tested on Simulation environment and
quite a bit of them have been tested on real hardware.
This patch brings new fixes after a series of tests carried out on new
equipment:
- Add POWER9 definition.
- Re-enable any masked interrupts when the AFU is not activated
after resetting the AFU.
- Remove the api cxl_is_psl8/9 which is no longer useful.
- Do not dump CAPI1 registers.
- Rewrite cxl_is_page_fault() function.
- Do not register slb callack on P9.
Fixes: f24be42aab37 ("cxl: Add psl9 specific code")
Signed-off-by: Christophe Lombard <clombard@linux.vnet.ibm.com>
Acked-by: Frederic Barrat <fbarrat@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Pull in the fix for shared tags, as it conflicts with the pending
changes in for-4.13/block. We already pulled in v4.12-rc5 to solve
other conflicts or get fixes that went into 4.12, so not a lot
of changes in this merge.
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
into next
|
|
git://anongit.freedesktop.org/git/drm-misc into drm-fixes
UAPI Changes:
- drm: Fix regression in GETCONNECTOR ioctl returning stale properties (Daniel)
Cc: Daniel Vetter <daniel.vetter@ffwll.ch>
* tag 'drm-misc-fixes-2017-06-22' of git://anongit.freedesktop.org/git/drm-misc:
drm: Fix GETCONNECTOR regression
|
|
CONFIG_COMPILE_TEST allows building a configuration without
TI_SCI_PROTOCOL, which then fails to link:
drivers/clk/keystone/sci-clk.o: In function `ti_sci_clk_probe':
sci-clk.c:(.text.ti_sci_clk_probe+0x4c): undefined reference to `devm_ti_sci_get_handle'
This makes it a hard dependency. Right now, that means we can't
actually compile-test the driver unless ARCH_KEYSTONE is set as
well, but we can fix that by allowing TI_MESSAGE_MANAGER to
be selected for COMPILE_TEST as well.
Fixes: b745c0794e2f ("clk: keystone: Add sci-clk driver support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Tero Kristo <t-kristo@ti.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Allow the intel-hid driver to wake up the system from suspend-to-idle
by configuring its platform device as a wakeup one by default and
switching it over to a system wakeup events triggering mode during
system suspend transitions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
Allow the intel-vbtn driver to wake up the system from suspend-to-idle
by configuring its platform device as a wakeup one by default and
switching it over to a system wakeup events triggering mode during
system suspend transitions.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
|
|
NULL checks at line 457: if (!link0 || !link1) {, implies that both
pointers link0 and link1 might be NULL.
Function nfcsim_link_free() dereference pointers link0 and link1.
Add NULL checks before calling nfcsim_link_free() to avoid a
potential NULL pointer dereference.
Addresses-Coverity-ID: 1364857
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This reverts commit ab714817d7e891608d31f6996b1e4c43cf2bf342.
The original commit was designed to handle a bug in the trf7970a NFC
controller where an extra byte was returned in Read Multiple Blocks (RMB)
command responses. However, it has become less clear whether it is a bug
in the trf7970a or in the tag. In addition, it was assumed that the extra
byte was always returned but it turns out that is not always the case. The
result is that a byte of good data is trimmed off when the extra byte is
not present ultimately causing the neard deamon to fail the read.
Since the trf7970a driver does not have the context to know when to trim
the byte or not, remove the code from the trf7970a driver all together
(and move it up to the neard daemon). This has the added benefit of
simplifying the kernel driver and putting the extra complexity into
userspace.
CC: Rob Herring <robh@kernel.org>
CC: devicetree@vger.kernel.org
Signed-off-by: Mark Greer <mgreer@animalcreek.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The "or" condition (clk_freq != TRF7970A_27MHZ_CLOCK_FREQUENCY) ||
(clk_freq != TRF7970A_13MHZ_CLOCK_FREQUE) will always be true because
clk_freq cannot be equal to two different values at the same time. Use
the && operator instead of || to fix this.
Detected by CoverityScan, CID#1430468 ("Constant expression result")
Fixes: 837eb4d21ecde7 ("NFC: trf7970a: add device tree option for 27MHz clock")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Geoff Lansberry <geoff@kuvee.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Similarly to commit f1e9203e2366 ("clk: samsung: Fix Exynos 5420 pinctrl
setup and clock disable failure due to domain being gated") for
Exynos5420, the Exynos4412 also requires that EPLL is not disabled.
Otherwise any access to MAUDIO block will silently halt.
This was not visible before because EPLL on Exynos4 could not be
disabled before commit 6edfa11cb396 ("clk: samsung:
Add enable/disable operation for PLL36XX clocks"). After this commit,
on Odroid U3 board one can see silent hang, usually with last (but
unrelated) messages:
[ 2.382741] input: gpio_keys as /devices/platform/gpio_keys/input/input0
[ 2.405686] usb 1-3: new high-speed USB device number 3 using exynos-ehci
[ 2.419843] max77686-rtc max77686-rtc: setting system clock to 2017-06-21 17:04:13 UTC (1498064653)
Mark Exynos4 variant as also needed EPLL to be enabled all the time.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Use unified device properties API in meaningful way.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since we got rid of platform data, the driver may use GPIO descriptor
directly.
Looking deeply to the use of the GPIO pin it looks like it should be
a GPIO based reset control rather than custom GPIO handling. But this
is out of scope of the change.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
I2C and SPI frameworks followed by IRQ framework do set
interrupt polarity correctly if it's properly specified in firmware
(ACPI or DT).
Get rid of the redundant trick when requesting interrupt.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Legacy platform data must go away. We are on the safe side here since
there are no users of it in the kernel.
If anyone by any odd reason needs it the GPIO lookup tables and
built-in device properties at your service.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
It looks like there are two leftovers, at least one of which can leak
the resource (IRQ).
Convert both places to use managed variants of the functions.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
There is no platform code that uses i2c module table.
Remove it altogether and adjust ->probe() to be ->probe_new().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Since OF and ACPI case almost the same get rid of code duplication
by moving gpiod_get() calls directly to ->probe().
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
In order to make GPIO ACPI library stricter prepare users of
gpiod_get_index() to correctly behave when there no mapping is
provided by firmware.
Here we add explicit mapping between _CRS GpioIo() resources and
their names used in the driver.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Switch to use managed variant of acpi_dev_add_driver_gpios() to simplify
error path and fix potentially wrong assignment if ->probe() fails.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Show the name of the member (scanned_channels) that provides the
length with some better markup.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Use kstrtou32_from_user() in debugfs instead of open-coding it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
On A000 HW, the SCD rdptr has only 8 bits allocated
for it, thus when checking if a queue is full, or
when checking if the SSN is equal to the TID's
next_reclaimed, A000 HW should trim the SSN.
Fix this by "normalizing" the SSN to wrap around
0xFF when comparing to the next_reclaimed on A000
HW.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't actually care about the value at all, just making sure
that we can successfully parse a single integer value, but that's
entirely pointless - remove it.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When toggling the RF-kill pin quickly in succession, the driver can
get rather confused because it might be in the process of shutting
down, expecting all commands to go through quickly due to rfkill,
but the transport already thinks the device is accessible again,
even though it previously shut it down. This leads to bugs, and I
even observed a kernel panic.
Avoid this by making the PCIe code only report that the radio is
enabled again after the higher layers actually decided to shut it
off.
This also pulls out this common RF-kill checking code into a common
function called by both transport generations and also moves it to
the direct method - in the internal helper we don't really care
about the RF-kill status anymore since we won't report it up until
the stop anyway.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If we happen to be in or get into the queue sync when RF-kill
is asserted, we return from there and warn since there are
still queue sync notifications outstanding. These can't ever
come though, because we're in RF-kill, so don't WARN then.
While at it, also move the warning to the appropriate place,
if the request is not synchronous then we shouldn't warn, but
currently always will.
To make it fast, also trigger the waitq when on rfkill assert.
Fixes: 0636b938214c ("iwlwifi: mvm: implement driver RX queues sync command")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In order to debug "hardware" RF-kill flows, add a low-level hook to
allow changing the "hardware" RF-kill from debugfs.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There's no point in duplicating exactly the same code here
for legacy and MSI-X interrupts, so pull it out into a new
function to call in both places.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In case that rate's antenna is wrong at the init stage, it's
very hard to say what went wrong. Add debug data to the already
existing WARN_ON_ONCE.
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Some static checkers (e.g. smatch) complain about the logic, saying that
resp_cp might be leaked. Clearly that isn't true, but making the logic
easier to follow does not result in any significant code changes and makes
the code more readable by moving the NULL check closer to its source.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The firmware moved the development from a0 MAC to z0.
z0 is using the same RFID and device ID as a0 so we only
need to switch the name.
Signed-off-by: Mordechai Goodstein <mordechay.goodstein@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
New FW versions require the D0I3_END_CMD to be sent as the first
command to the FW in the resume flow. If the TLV is set, send that
command first, otherwise keep the original behavior (i.e. send last).
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
There is no need to send D0I3_END_CMD as ASYNC during the system
resume flow. Additionally, the other flags used are meaningless in
this case (they were just copied from the runtime resume flow), so
remove them all.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Shaul reported that when iwlmvm was sending beacons, it didn't properly
also take ownership of the probe responses. This is because the whole
mac80211 callback (tx_last_beacon) wasn't implemented. Fix that to make
IBSS discovery work better.
Reported-by: Shaul Triebitz <shaul.triebitz@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Letting the preprocessor/compiler generate the shift/mask by itself
is a win for readability, so use bitfield.h for some registers.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
It's safer to use scnprintf() here because the buffer might
be too short for the full format strings. In most cases
this isn't true because of external limits on the values.
In one case, this fixes a stack data leak.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Avoid one kind of symbol shadowing another in iwl_mvm_flush_sta()
by renaming the function parameter.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The queue ID should never be 512 either, so correct the check
to be >= instead of just >.
Fixes: 310181ec34e2 ("iwlwifi: move to TVQM mode")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Since we exit if buf->num_stored is 0, there's no need to
check it again later.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When sending a Tx Command with a Tx packet, we allocate the
Tx command separately from the payload of the packet.
The WiFi MAC header is then copied into the buffer that was
allocated for the Tx Command. This means that this buffer
needs to be big enough to contain both. This is why it is
allocated with iwl_trans_alloc_tx_cmd which returns a
pointer to a newly allocated not zeroed struct
iwl_device_cmd.
The Tx command has a few bit fields and hence it needs to
be zeroed, but all the rest of the buffer doesn't need to
be zeroed since it will either be memcopy'ed with the MAC
header, or not even sent to the device.
This means that we don't need to zero all the
iwl_device_cmd structure, but rather only the size of
the iwl_tx_cmd structure.
Since sizeof(iwl_tx_cmd) - sizeof(iwl_tx_cmd) is about
260 bytes, this can avoid touching 4 cache lines for each
packet.
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Install GTKs on AP side for new TX API.
Don't add IV space, it's added by the HW.
While at that fix GCMP abnd GCMP-256 GTK installation
which work similarly to the new TX API.
Signed-off-by: David Spinadel <david.spinadel@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
If FW isn't alive, trying to collect debug data will
result in errors both in driver and in the collected
data, so just warn and leave the collecting function
in this case.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
