| Age | Commit message (Collapse) | Author |
|---|
|
Initialize data_index where appropriate to improve readability and
assist debugging. This change doesn't affect driver behaviour.
I prefer to see
current_req->data[data_index++]
in place of
current_req->data[0]
or
current_req->data[1]
inasmuchas it becomes obvious what the data_index variable does.
Moreover, the actual value of data_index when examined at any given moment
tells me something about prior events, which did prove helpful.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The cuda_start() function uses spinlock_irq_save/restore for mutual
exclusion. Let's have cuda_poll() do the same when polling the VIA
interrupt.
The benefit to disabling local irqs when the interrupt is being polled
is that the interrupt handler now has the same timing properties
regardless of whether it is invoked normally or from cuda_poll().
This driver was written back when local irqs remained enabled during
execution of interrupt handlers and cuda_poll() was probably trying
to achieve the same effect by use of enable/disable_irq.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When a read transaction completes, one of several things will happen:
a new transfer is started by the driver, a new transfer request
is raised by the Cuda (i.e. TREQ asserted), or both happen at once.
When both happen at once, there is a race condition between the TREQ test
in the read_done state and the same test in cuda_start(). Moreover, the
former test uses a stale TREQ value.
Theoretically, this can result in the undesirable outcome that the
interrupt handler completes with the state machine 'idle' when it should
instead start the next transaction.
Avoid this race by calling cuda_start() first and then confirming that it
succeeded. If not, test the current TREQ value before entering the
'reading' state.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When reading_reply is set, reply_ptr points into an adb_request struct.
Conversely, when reply_ptr instead points into the global cuda_rbuf,
reading_reply must be false.
Unfortunately, this rule can be violated because re-initialization
of reply_ptr and reading_reply presently depends on the TREQ input.
Fix this by re-initializing reply_ptr and reading_reply as soon as they
are known to be invalid.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
If the Cuda driver does not enter the 'read_done' state for some
reason, it may continue in the 'reading' state until the buffer
overflows. Add a bounds check to prevent this.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Introduce some helpers for handling the signalling between VIA and
Cuda. This abstraction will be used to add support for Egret devices,
which utilize slightly different signalling.
Don't invert the sense of the Cuda's active-low signals when storing
them in the 'status' variable. Just assert, negate and test those
signals using the helpers.
The state machine does not need to test its own output signals to
figure out what to do next: the next state depends on the Cuda's TREQ
output. Just call the TREQ_asserted() helper function to test for that.
Similarly, there is no need to store pin directions in the 'status'
variable. That was only useful for debugging messages.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
There is no possibility that current_req can change during execution of
cuda_start(). This can be confirmed by inspection: cuda_lock is always
held whenever cuda_start() is called or current_req is modified.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add missing log message severity, remove old debug messages and
replace printk() loop with print_hex_dump() call.
Tested-by: Stan Johnson <userm57@yahoo.com>
Signed-off-by: Finn Thain <fthain@telegraphics.com.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Macvtap functions read the value once, but unless READ_ONCE is used,
the compiler may ignore this and read multiple times. Enforce a single
read and locally cached value to avoid updates between test and use.
Signed-off-by: Willem de Bruijn <willemb@google.com>
Suggested-by: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When IFF_VNET_HDR is enabled, a virtio_net header must precede data.
Data length is verified to be greater than or equal to expected header
length tun->vnet_hdr_sz before copying.
Read this value once and cache locally, as it can be updated between
the test and use (TOCTOU).
Signed-off-by: Willem de Bruijn <willemb@google.com>
Reported-by: Dmitry Vyukov <dvyukov@google.com>
CC: Eric Dumazet <edumazet@google.com>
Acked-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
"None of these are showstoppers for 4.10 and could wait for 4.11 merge
window, but they are low enough risk for this late in the cycle and
the fixes have waiting users . They have received a build success
notification from the 0day robot, pass the latest ndctl unit tests,
and appeared in next:
- Fix a crash that can result when SIGINT is sent to a process that
is awaiting completion of an address range scrub command. We were
not properly cleaning up the workqueue after
wait_event_interruptible().
- Fix a memory hotplug failure condition that results from not
reserving enough space out of persistent memory for the memmap. By
default we align to 2M allocations that the memory hotplug code
assumes, but if the administrator specifies a non-default
4K-alignment then we can fail to correctly size the reservation.
- A one line fix to improve the predictability of libnvdimm block
device names. A common operation is to reconfigure /dev/pmem0 into
a different mode. For example, a reconfiguration might set a new
mode that reserves some of the capacity for a struct page memmap
array. It surprises users if the device name changes to
"/dev/pmem0.1" after the mode change and then back to /dev/pmem0
after a reboot.
- Add 'const' to some function pointer tables"
* 'libnvdimm-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm, pfn: fix memmap reservation size versus 4K alignment
acpi, nfit: fix acpi_nfit_flush_probe() crash
libnvdimm, namespace: do not delete namespace-id 0
nvdimm: constify device_type structures
|
|
Signed-off-by: Christoph Hellwig <hch@lst.de>
Acked-by: Jack Wang <jinpu.wang@profitbricks.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
They are never called and just dispatch to methods of the same names in
the FC and SRP transport classes that are never implemented.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Instead define the timeout behavior purely based on the host_template
eh_timed_out method and wire up the existing transport implementations
in the host templates. This also clears up the confusion that the
transport template method overrides the host template one, so some
drivers have to re-override the transport template one.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Reviewed-by: Tyrel Datwyler <tyreld@linux.vnet.ibm.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
EH_NOT_HANDLED is the default case if no eh_timed_out method is
provided, so there is no need to supply it.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
These days we can specify an eh_timed_out handler in the host_template,
so don't have a transport_template definition just for it.
[mkp: fixed typo]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Martin K. Petersen <martin.petersen@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management fixes from Rafael Wysocki:
"These add a quirk to intel_pstate to work around a firmware setting
that leads to frequency scaling issues (discovered recently) on some
Intel Kaby Lake processors, fix up the recently added brcmstb-avs
cpufreq driver and avoid false-positive warnings from the runtime PM
framework triggered by recent changes in i915.
Specifics:
- Add an intel_pstate driver quirk to work around a firmware setting
that leads to frequency scaling issues on desktop Intel Kaby Lake
processors in some configurations if the hardware-managed P-states
(HWP) feature is in use (Srinivas Pandruvada)
- Fix up the recently added brcmstb-avs cpufreq driver: fix a bug
related to system suspend and change the sysfs interface to match
the user space expectations (Markus Mayer)
- Modify the runtime PM framework to avoid false-positive warnings
from the might_sleep_if() assertions in it (Rafael Wysocki)"
* tag 'pm-4.10-rc8' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm:
PM / runtime: Avoid false-positive warnings from might_sleep_if()
cpufreq: intel_pstate: Disable energy efficiency optimization
cpufreq: brcmstb-avs-cpufreq: properly retrieve P-state upon suspend
cpufreq: brcmstb-avs-cpufreq: extend sysfs entry brcm_avs_pmap
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fixes from Mike Snitzer:
- a fix for a race in .request_fn request-based DM request handling vs
DM device destruction
- an RCU fix for dm-crypt's kernel keyring support that was included in
4.10-rc1
- a -Wbool-operation warning fix for DM multipath
* tag 'dm-4.10-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm crypt: replace RCU read-side section with rwsem
dm rq: cope with DM device destruction while in dm_old_request_fn()
dm mpath: cleanup -Wbool-operation warning in choose_pgpath()
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media fixes from Mauro Carvalho Chehab:
"A few documentation fixes at CEC (with got promoted from staging for
4.10), and one fix on its core."
* tag 'media/v4.10-3' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media:
[media] cec: fix wrong last_la determination
[media] cec-intro.rst: mention the v4l-utils package and CEC utilities
[media] cec rst: remove "This API is not yet finalized" notice
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto fixes from Herbert Xu:
- use-after-free in algif_aead
- modular aesni regression when pcbc is modular but absent
- bug causing IO page faults in ccp
- double list add in ccp
- NULL pointer dereference in qat (two patches)
- panic in chcr
- NULL pointer dereference in chcr
- out-of-bound access in chcr
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6:
crypto: chcr - Fix key length for RFC4106
crypto: algif_aead - Fix kernel panic on list_del
crypto: aesni - Fix failure when pcbc module is absent
crypto: ccp - Fix double add when creating new DMA command
crypto: ccp - Fix DMA operations when IOMMU is enabled
crypto: chcr - Check device is allocated before use
crypto: chcr - Fix panic on dma_unmap_sg
crypto: qat - zero esram only for DH85x devices
crypto: qat - fix bar discovery for c62x
|
|
In commit abeffce ("net/mlx5e: Fix a -Wmaybe-uninitialized warning"), I fixed a
gcc warning for the ipv4 offload handling. Now we get the same warning for the
added ipv6 support:
drivers/net/ethernet/mellanox/mlx5/core/en_tc.c:815:40: warning: 'out_dev' may be used uninitialized in this function [-Wmaybe-uninitialized]
We can apply the same workaround here as well.
Fixes: ce99f6b97fcd ("net/mlx5e: Support SRIOV TC encapsulation offloads for IPv6 tunnels")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Or Gerlitz <ogerlitz@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch makes use of is_vlan_dev() function instead of flag
comparison which is exactly done by is_vlan_dev() helper function.
Signed-off-by: Parav Pandit <parav@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Acked-by: Stephen Hemminger <stephen@networkplumber.org>
Acked-by: Jon Maxwell <jmaxwell37@gmail.com>
Acked-by: Johannes Thumshirn <jth@kernel.org>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The function iort_add_smmu_platform_device() accidentally returns 0
(ie PTR_ERR(pdev) where pdev == NULL) if platform_device_alloc() fails;
fix the bug by returning a proper error value.
Fixes: 846f0e9e74a0 ("ACPI/IORT: Add support for ARM SMMU platform devices creation")
Acked-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
[lorenzo.pieralisi@arm.com: improved commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Commit 618f535a6062 ("ACPI/IORT: Add single mapping function")
introduced a function (iort_node_get_id()) to retrieve ids for IORT
named components.
The iort_node_get_id() takes an index as input to refer to a specific
mapping entry in the named component IORT node mapping array.
For a mapping entry at a given index, iort_node_get_id() should return
the id value (through the id_out function parameter) and the IORT node
output_reference (through function return value) the given mapping entry
refers to.
Technically output_reference values may differ for different map
entries, (see diagram below - mapped id values may refer to different eg
IORT SMMU nodes; the kernel may not be able to handle different
output_reference values for a given named component but the IORT kernel
layer should still report the IORT mappings as reported by firmware) but
current code in iort_node_get_id() fails to use the index function
parameter to return the correct output_reference value (ie it always
returns the output_reference value of the first entry in the mapping
array whilst using the index correctly to retrieve the id value from the
respective entry).
|----------------------|
| named component |
|----------------------|
| map entry[0] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 1
|----------------------|
| map entry[1] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 2
|----------------------|
.
.
.
|----------------------|
| map entry[N] |
|----------------------|
| id value |
| output_reference----------------> eg SMMU 1
|----------------------|
Consequently the iort_node_get_id() function always returns the IORT
node pointed at by the output_reference value of the first named
component mapping array entry, irrespective of the index parameter,
which is a bug.
Update the map array entry pointer computation in iort_node_get_id() to
take into account the index value, fixing the issue.
Fixes: 618f535a6062 ("ACPI/IORT: Add single mapping function")
Reported-by: Hanjun Guo <hanjun.guo@linaro.org>
Reviewed-by: Hanjun Guo <hanjun.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Hanjun Guo <hanjun.guo@linaro.org>
Cc: Sinan Kaya <okaya@codeaurora.org>
Cc: Tomasz Nowicki <tn@semihalf.com>
Cc: Nate Watterson <nwatters@codeaurora.org>
Cc: "Rafael J. Wysocki" <rjw@rjwysocki.net>
Signed-off-by: Will Deacon <will.deacon@arm.com>
|
|
Interface numbers do not change when enabling alternate settings as
comment and code in this driver suggested.
Remove the confusing comment and redundant retrieval of the interface
number in probe, while simplifying and renaming the interface-number
helper.
Fixes: 4db2299da213 ("sierra: driver interface blacklisting")
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
FTDI devices use a receive latency timer to periodically empty the
receive buffer and report modem and line status (also when the buffer is
empty).
When a break or error condition is detected the corresponding status
flags will be set on a packet with nonzero data payload and the flags
are not updated until the break is over or further characters are
received.
In order to avoid over-reporting break and error conditions, these flags
must therefore only be processed for packets with payload.
This specifically fixes the case where after an overrun, the error
condition is continuously reported and NULL-characters inserted until
further data is received.
Reported-by: Michael Walle <michael@walle.cc>
Fixes: 72fda3ca6fc1 ("USB: serial: ftd_sio: implement sysrq handling on
break")
Fixes: 166ceb690750 ("USB: ftdi_sio: clean up line-status handling")
Cc: stable <stable@vger.kernel.org> # v2.6.35
Signed-off-by: Johan Hovold <johan@kernel.org>
|
|
Support new version of beacon template command which deprecates
the use of the tx command inside.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When resuming, it's possible for the following scenario to occur:
* iwl_pci_resume() enables the RF-kill interrupt
* iwl_pci_resume() reads the RF-kill state (e.g. to 'radio enabled')
* RF_KILL interrupt triggers, and iwl_pcie_irq_handler() reads the
state, now 'radio disabled', and acquires the &trans_pcie->mutex.
* iwl_pcie_irq_handler() further calls iwl_trans_pcie_rf_kill() to
indicate to the higher layers that the radio is now disabled (and
stops the device while at it)
* iwl_pcie_irq_handler() drops the mutex
* iwl_pci_resume() continues, acquires the mutex and calls the higher
layers to indicate that the radio is enabled.
At this point, the device is stopped but the higher layers think it's
available, and can call deeply into the driver to try to enable it.
However, this will fail since the device is actually disabled.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Support differentiating between two phys for a000 devices
in order to load the correct firmware.
Eventually when moving completely to the new phy we will be
able to remove this.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The iwl_drv structure contains trans which already contains cfg, so
storing cfg separately in iwl_drv is redundant. Remove it and access
trans->cfg instead.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When iwl_drv_start() is called, trans->cfg must already be set, so
there's no need to pass cfg separately, since it can be accessed
directly from trans->cfg.
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Unify code, remove redundant assignments.
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
When a small frame is copied completely into the skb->head, the code
doesn't take alignment into account, making mac80211 copy it again
later on architectures that need the alignment. Avoid this by taking
the PAD flag from the device into account when copying.
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
In DQA mode the check whether to decrement the pending frames
counter relies on the tid status and not on the txq id.
This may result in an inconsistent state of the pending frames
counter in case frame is queued on a non aggregation queue but
with this TID, and will be followed by a failure to remove the
station and later on SYSASSERT 0x3421 when trying to remove the
MAC.
Such frames are for example bar and qos NDPs.
Fix it by aligning the condition of incrementing the counter
with the condition of decrementing it - rely on TID state for
DQA mode.
Also, avoid internal error like this affecting station removal
for DQA mode - since we can know for sure it is an internal
error.
Fixes: cf961e16620f ("iwlwifi: mvm: support dqa-mode agg on non-shared queue")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Our 9000 device supports 64 bit DMA address for RX only, and
not for TX.
Setting DMA mask to 64 for the whole device is erroneous - we
can do it only for a000 devices where device is capable of
both RX & TX DMA with 64 bit address space.
Fixes: 96a6497bc3ed ("iwlwifi: pcie: add 9000 series multi queue rx DMA support")
Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
A few of the static queues are enabled along with the bcast
STA. Make sure they are removed along with it, rather than
waiting for the mac ctxt release.
This is needed because we sometimes have a STA being removed
and then added again (either with the same sta_id or a
different one). If we wait for the mac ctxt release we will
try to allocate the queues again (as this is currently done
in the STA allocation and not in the MAC init) although
they weren't freed, and even if the sta_id of the STA has
changed.
Signed-off-by: Liad Kaufman <liad.kaufman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
Instead of setting the tx_cmd length in the mvm code, which is
complicated by the fact that DQA may want to temporarily store
the SKB on the side, adjust the length in the PCIe code which
also knows about this since it's responsible for duplicating
all those headers that are account for in this code.
As the PCIe code already relies on the tx_cmd->len field, this
doesn't really introduce any new dependencies.
To make this possible we need to move the memcpy() of the TX
command until after it was updated.
This does even simplify the code though, since the PCIe code
already does a lot of manipulations to build A-MSDUs correctly
and changing the length becomes a simple operation to see how
much was added/removed, rather than predicting it.
Fixes: 24afba7690e4 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
We don't really need clear the skb's status area nor store the
dev_cmd into it until we really commit to the frame by handing
it to the transport - defer those operations until just before
we do that.
This doesn't entirely fix the bug with frames not getting sent
out after having been deferred due to DQA, because it doesn't
restore the info->driver_data[0] place that was already set to
zero (or another value) by the A-MSDU logic.
Fixes: 24afba7690e4 ("iwlwifi: mvm: support bss dynamic alloc/dealloc of queues")
Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
|
|
The use of ACCESS_ONCE() looks like a micro-optimization to force gcc to use
an indexed load for the register address, but it has an absolutely detrimental
effect on builds with gcc-5 and CONFIG_KASAN=y, leading to a very likely
kernel stack overflow aside from very complex object code:
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_update_stats':
hisilicon/hns/hns_dsaf_gmac.c:419:1: error: the frame size of 2912 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_reset_common':
hisilicon/hns/hns_dsaf_ppe.c:390:1: error: the frame size of 1184 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_ppe.c: In function 'hns_ppe_get_regs':
hisilicon/hns/hns_dsaf_ppe.c:621:1: error: the frame size of 3632 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_common_regs':
hisilicon/hns/hns_dsaf_rcb.c:970:1: error: the frame size of 2784 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_gmac.c: In function 'hns_gmac_get_regs':
hisilicon/hns/hns_dsaf_gmac.c:641:1: error: the frame size of 5728 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_rcb.c: In function 'hns_rcb_get_ring_regs':
hisilicon/hns/hns_dsaf_rcb.c:1021:1: error: the frame size of 2208 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_comm_init':
hisilicon/hns/hns_dsaf_main.c:1209:1: error: the frame size of 1904 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_xgmac.c: In function 'hns_xgmac_get_regs':
hisilicon/hns/hns_dsaf_xgmac.c:748:1: error: the frame size of 4704 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_update_stats':
hisilicon/hns/hns_dsaf_main.c:2420:1: error: the frame size of 1088 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
hisilicon/hns/hns_dsaf_main.c: In function 'hns_dsaf_get_regs':
hisilicon/hns/hns_dsaf_main.c:2753:1: error: the frame size of 10768 bytes is larger than 1024 bytes [-Werror=frame-larger-than=]
This does not seem to happen any more with gcc-7, but removing the ACCESS_ONCE
seems safe anyway and it avoids a serious issue for some people. I have verified
that with gcc-5.3.1, the object code we get is better in the new version
both with and without CONFIG_KASAN, as we no longer allocate a 1344 byte
stack frame for hns_dsaf_get_regs() but otherwise have practically identical
object code.
With gcc-7.0.0, removing ACCESS_ONCE has no effect, the object code is already
good either way.
This patch is probably not urgent to get into 4.11 as only KASAN=y builds
with certain compilers are affected, but I still think it makes sense to
backport into older kernels.
Cc: stable@vger.kernel.org
Fixes: 511e6bc ("net: add Hisilicon Network Subsystem DSAF support")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a "||" vs "|" typo here so we test 0x1 instead of 0x6.
Fixes: 1f8176f7352a ("net/mlx4_en: Check the enabling pptx/pprx flags in SET_PORT wrapper flow")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 364b6055738b ("net: busy-poll: return busypolling status
to drivers"), napi_complete_done() returns a boolean that can be used
by drivers to conditionally rearm interrupts.
Testing with a 7142 shows a small latency improvement of ~100 ns.
Signed-off-by: Bert Kenward <bkenward@solarflare.com>
Cc: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements the necessary logic to unlock an Opal
enabled device coming back from an S3.
The patch also implements the SED/Opal allocation necessary to support
the opal ioctls.
Signed-off-by: Scott Bauer <scott.bauer@intel.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We periodically ask the neighbouring system to try and resolve
neighbours that are used for nexthops, but aren't currently resolved.
However, 'nud_state' is protected by the neighbour lock, so we shouldn't
access it without taking it. Instead, we can simply check the
'connected' field of the neighbour entry, which we update upon
NEIGH_UPDATE events.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We only add neighbour entries that are also used for nexthops to
'nexthop_neighs_list', so when iterating over this list there's no need
to check that the entry is indeed used for nexthops.
Remove the redundant check.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In commit 18bfb924f000 ("net: introduce default neigh_construct/destroy
ndo calls for L2 upper devices") we added these ndos to stacked devices
such as team and bond, so that calls will be propagated to mlxsw.
However, previous commit removed the reliance on these ndos and no new
users of these ndos have appeared since above mentioned commit. We can
therefore safely remove this dead code.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Up until now we had two interfaces for neighbour related configuration:
ndo_neigh_{construct,destroy} and NEIGH_UPDATE netevents. The ndos were
used to add and remove neighbours from the driver's cache, whereas the
netevent was used to reflect the neighbours into the device's tables.
However, if the NUD state of a neighbour isn't NUD_VALID or if the
neighbour is dead, then there's really no reason for us to keep it
inside our cache. The only exception to this rule are neighbours that
are also used for nexthops, which we periodically refresh to get them
resolved.
We can therefore eliminate the ndo entry point into the driver and
simplify the code, making it similar to the FIB reflection, which is
based solely on events. This also helps us avoid a locking issue, in
which the RIF cache was traversed without proper locking during
insertion into the neigh entry cache.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit 33b1341cd1bf ("mlxsw: spectrum_router: Fix handling of
neighbour structure") we no longer use destination IP for neighbour
lookup, so remove it.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently associate each neighbour entry with a work item, so it's
not possible to have multiple events queued for the same neighbour
entry. However, this is about to be changed so that the neighbour entry
is only resolved when the work item is scheduled.
The above can result in a mismatch between the kernel's and the device's
neighbour table, unless the associated work items are processed in the
order in which they were submitted.
Do that by migrating the NEIGH_UPDATE work items to be processed in the
ordered workqueue which was recently introduced in mlxsw in commit
a3832b31898f ("mlxsw: core: Create an ordered workqueue for FIB
offload").
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We always use zero delay before queueing a work on the ordered workqueue
('mlxsw_owq'), so use work_struct directly instead of delayable work.
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
