| Age | Commit message (Collapse) | Author |
|---|
|
Device reported as working fine, so tell the driver not to warn about
it being untested.
Reported-by: Aex Aey <aexaey@gmail.com>
Signed-off-by: Jes Sorensen <Jes.Sorensen@gmail.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
BCM43455 is a more recent revision of the BCM4345. Some of the BCM43455
got a dedicated SDIO device ID which is currently not supported by
brcmfmac.
Adding the new sdio_device_id to brcmfmac is enough to get the BCM43455
supported because the chip itself is already supported (due to BCM4345
support in the driver).
Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>
Reviewed-by: Andreas Färber <afaerber@suse.de>
Tested-by: Andreas Färber <afaerber@suse.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Marvell folks tell me this is a debugging event that the driver doesn't
need to handle, but on 8997 w/ firmware 16.68.1.p97, I see several of
these sorts of messages at (for instance) boot time:
[ 13.825848] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 14.838561] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 14.850397] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
[ 32.529923] mwifiex_pcie 0000:01:00.0: event: unknown event id: 0x63
Let's handle this "event" with a much lower verbosity.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
In mwifiex_delay_for_sleep_cookie(), we're looping and waiting for the
PCIe endpoint to write a magic value back to memory, to signal that it
has finished going to sleep. We're not letting the compiler know that
this might change underneath our feet though. Let's do that, for good
hygiene.
I'm not aware of this fixing any concrete problems. I also give no
guarantee that this loop is actually correct in any other way, but at
least this looks like an improvement to me.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The following sequence occurs when using IEEE power-save on 8997:
(a) driver sees SLEEP event
(b) driver issues SLEEP CONFIRM
(c) driver recevies CMD interrupt; within the interrupt processing loop,
we do (d) and (e):
(d) wait for FW sleep cookie (and often time out; it takes a while), FW
is putting card into low power mode
(e) re-check PCIE_HOST_INT_STATUS register; quit loop with 0 value
But at (e), no one actually signaled an interrupt (i.e., we didn't check
adapter->int_status). And what's more, because the card is going to
sleep, this register read appears to take a very long time in some cases
-- 3 milliseconds in my case!
Now, I propose that (e) is completely unnecessary. If there were any
additional interrupts signaled after the start of this loop, then the
interrupt handler would have set adapter->int_status to non-zero and
queued more work for the main loop -- and we'd catch it on the next
iteration of the main loop.
So this patch drops all the looping/re-reading of PCIE_HOST_INT_STATUS,
which avoids the problematic (and slow) register read in step (e).
Incidentally, this is a very similar issue to the one fixed in commit
ec815dd2a5f1 ("mwifiex: prevent register accesses after host is
sleeping"), except that the register read is just very slow instead of
fatal in this case.
Tested on 8997 in both MSI and (though not technically supported at the
moment) MSI-X mode.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Depending on system factors (e.g., the PCIe link PM state), the first
read to wake up the Wifi firmware can take a long time. There is no
reason to use a (blocking, non-posted) read at this point, so let's just
use a write instead. Write vs. read doesn't matter functionality-wise --
it's just a dummy operation. But let's make sure to re-write with the
correct "ready" signature, since we check for that in other parts of the
driver.
This has been shown to decrease the time spent blocking in this function
on RK3399.
Signed-off-by: Brian Norris <briannorris@chromium.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
|
|
The CI_HDRC_CONTROLLER_STOPPED_EVENT may want to call sleeping
APIs similar to how _gadget_stop_activity() may. Let's drop the
lock across the event so that glue drivers can make sleeping
calls.
Cc: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
If something fails in ci_hdrc_add_device() due to probe defer, we
shouldn't print an error message. Be silent in this case as we'll
try probe again later.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly. Hook
the phy initialization into the RESET event and the phy power off
into the STOPPED event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The MSM chipidea wrapper has two bits that are used to reset the
first or second phy. Add support for these bits via the reset
controller framework, so that phy drivers can reset their
hardware at the right time during initialization.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
If two devices are probed with this same driver, they'll share
the same platform data structure, while the chipidea core layer
writes and modifies it. This can lead to interesting results
especially if one device is an OTG type chipidea controller and
another is a host. Let's create a copy of this structure per each
device instance so that odd things don't happen.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
When the RESET bit is set in the USBCMD register it resets quite
a few of the wrapper's registers to their reset state. This
includes the GENCONFIG and GENCONFIG2 registers. Currently this
is done by the usb phy and ehci-msm drivers writing into the
controller wrapper's MMIO address space. Let's consolidate the
register writes into the wrapper driver instead so that we
clearly split the wrapper from the phys.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We need to pick the correct phy at runtime based on how the SoC
has been wired onto the board. If the secondary phy is used, take
it out of reset and mux over to it by writing into the TCSR
register. Make sure to do this on reset too, because this
register is reset to the default value (primary phy) after the
RESET bit is set in USBCMD.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The msm chipidea controller uses two main clks, an AHB clk to
read/write the MMIO registers and a core clk called the system
clk that drives the controller itself. Add support for these clks
as they're required in all designs.
Also add support for an optional third clk that we need to turn
on to reset the controller and wrapper logic and other
"housekeeping" things. This clk was removed in later revisions of
the hardware because the reset methodology no longer required
clks to be enabled to propagate resets.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The MSM_USB_BASE macro trick is not very clear, and we're using
it for only one register write so let's just move to using
hw_write_id_reg() and passing the ci pointer instead. That
clearly shows what offset we're using and avoids needing to
include the msm_hsusb_hw.h file when we're going to delete that
file soon.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The core framework already handles setting this parameter with a
platform quirk. Add the appropriate flag so that we always set
AHBBURST to 0. Technically DT should be doing this, but we always
do it for msm chipidea devices so setting the flag in the driver
works just as well. If the burst needs to be anything besides 0,
we expect the 'ahb-burst-config' dts property to be present.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We're not properly marking the glue layer/wrapper device as
runtime active, so runtime PM believes that the hardware state is
inactive when we call pm_runtime_enable() in this driver. This
causes a problem when the glue layer has a power domain
associated with it, because runtime PM will go and disable the
power domain to match the 'inactive' state of the device. Let's
mark the device as active so that runtime PM doesn't improperly
power down this device when it's actually active.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
At some situations, the vbus may already be there before starting
gadget. So we need to check vbus event after switching to gadget in
order to handle missing vbus event. The typical use cases are plugging
vbus cable before driver load or the vbus has already been there
after stopping host but before starting gadget.
Signed-off-by: Peter Chen <peter.chen@nxp.com>
Tested-by: Stephen Boyd <stephen.boyd@linaro.org>
Reported-by: Stephen Boyd <stephen.boyd@linaro.org>
|
|
DECON_TV requires STANDALONE_UPDATE after output enabling, otherwise it does
not start. This change is neutral for DECON.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
The two extcon notifiers are almost the same except for the
variable name for the cable structure and the id notifier inverts
the cable->state logic. Make it the same and replace two
functions with one to save some lines. This also makes it so that
the id cable state is true when the id pin is pulled low, so we
change the name of ->state to ->connected to properly reflect
that we're interested in the cable being connected.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
DECON_CMU register has reserved bits which should not be zeroed, otherwise
IP can behave strangely and cause IOMMU faults.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
decon_commit is called just after reset so video is disabled anyway.
Signed-off-by: Andrzej Hajda <a.hajda@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
|
|
Commit 04aeb56a1732 ("net/mlx4_en: allocate non 0-order pages for RX
ring with __GFP_NOMEMALLOC") added code that appears to be not needed at
that time, since mlx4 never used __GFP_MEMALLOC allocations anyway.
As using memory reserves is a must in some situations (swap over NFS or
iSCSI), this patch adds this flag.
Note that this driver does not reuse pages (yet) so we do not have to
add anything else.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Konstantin Khlebnikov <khlebnikov@yandex-team.ru>
Cc: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This reverts commit 3e884493448131179a5b7cae1ddca1028ffaecc8.
With commit 529ed1275263 ("net: phy: phy drivers should not set
SUPPORTED_[Asym_]Pause"), phylib now handles automatically enabling
pause frame support in the PHY, and the MAC driver should follow suit.
Since the EMAC driver driver does this, we no longer need to force
pause frames support.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some phys for the chipidea controller are controlled via the ULPI
viewport. Add support for the ULPI bus so that these sorts of
phys can be probed and read/written automatically without having
to duplicate the viewport logic in each phy driver.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We don't call hw_device_reset() with the ci->lock held, so it
doesn't seem like this lock here is protecting anything. Let's
just remove it. This allows us to call sleeping functions like
phy_init() from within the CI_HDRC_CONTROLLER_RESET_EVENT hook.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The chipidea/udc.c file sends a CI_HDRC_CONTROLLER_RESET_EVENT to
the wrapper drivers when it calls hw_device_reset(), but that
function is not called from chipidea/host.c. And the udc.c file
sends the CI_HDRC_CONTROLLER_STOPPED_EVENT but the host.c file
doesn't do anything.
The intent of the reset event is to allow the wrapper driver to
do any wrapper specific things after the reset bit has been set
in the usb command register. Therefore, add this event hook in
the host role after we toggle that bit.
Similarly, the intent of the stopped event is to allow the
wrapper driver to do any wrapper specific things after the device
is stopped. So when we stop the host role, send the stopped
event.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The ULPI phy on qcom platforms needs to be initialized and
powered on after a USB reset and before we toggle the run/stop
bit. Otherwise, the phy locks up and doesn't work properly.
Therefore, add a flag to skip any phy power management in the
core layer, leaving it up to the glue driver to manage.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
We're currently emulating the vbus and id interrupts in the OTGSC
read API, but we also need to make sure that if we're handling
the events with extcon that we don't enable the interrupts for
those events in the hardware. Therefore, properly emulate this
register if we're using extcon, but don't enable the interrupts.
This allows me to get my cable connect/disconnect working
properly without getting spurious interrupts on my device that
uses an extcon for these two events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
With the id and vbus detection done via extcon we need to make
sure we poll the status of OTGSC properly by considering what the
extcon is saying, and not just what the register is saying. Let's
move this hw_wait_reg() function to the only place it's used and
simplify it for polling the OTGSC register. Then we can make
certain we only use the hw_read_otgsc() API to read OTGSC, which
will make sure we properly handle extcon events.
Acked-by: Peter Chen <peter.chen@nxp.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Ivan T. Ivanov" <iivanov.xz@gmail.com>
Fixes: 3ecb3e09b042 ("usb: chipidea: Use extcon framework for VBUS and ID detect")
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The qcom HSIC ULPI phy doesn't have any bits set in the vendor or
product ID registers. This makes it impossible to make a ULPI
driver match against the ID registers. Add support to discover
the ULPI phys via DT help alleviate this problem. In the DT case,
we'll look for a ULPI bus node underneath the device registering
the ULPI viewport (or the parent of that device to support
chipidea's device layout) and then match up the phy node
underneath that with the ULPI device that's created.
The side benefit of this is that we can use standard properties
in the phy node like clks, regulators, gpios, etc. because we
don't have firmware like ACPI to turn these things on for us. And
we can use the DT phy binding to point our phy consumer to the
phy provider.
The ULPI bus code supports native enumeration by reading the
vendor ID and product ID registers at device creation time, but
we can't be certain that those register reads will succeed if the
phy is not powered up. To avoid any problems with reading the ID
registers before the phy is powered we fallback to DT matching
when the ID reads fail.
If the ULPI spec had some generic power sequencing for these
registers we could put that into the ULPI bus layer and power up
the device before reading the ID registers. Unfortunately this
doesn't exist and the power sequence is usually device specific.
By having the device matched up with DT we can avoid this
problem.
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Cc: <devicetree@vger.kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
The ULPI bus can be built as a module, and it will soon be
calling these functions when it supports probing devices from DT.
Export them so they can be used by the ULPI module.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
In the case of ULPI devices, we want to be able to load the
driver before registering the device so that we don't get stuck
in a loop waiting for the phy module to appear and failing usb
controller probe. Currently we request the ulpi module via the
ulpi ids, but in the DT case we might need to request it with the
OF based modalias instead. Add a common function that allows
anyone to request a module with the OF based modalias.
Acked-by: Rob Herring <robh@kernel.org>
Cc: <devicetree@vger.kernel.org>
Signed-off-by: Stephen Boyd <stephen.boyd@linaro.org>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
This patch uses the resource-managed extcon API for extcon_register_notifier()
and replaces the deprecated extcon API as following:
- extcon_get_cable_state_() -> extcon_get_state()
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Peter Chen <peter.chen@nxp.com>
|
|
There is a hidden logic for acpi_tb_install_standard_table() as it can be
invoked from the boot stage and during runtime.
1. When it is invoked from the OS boot stage, the ACPICA mutex may not have
been initialized yet and so acpi_ut_acquire_mutex()/acpi_ut_release_mutex()
are not invoked in these code paths:
acpi_initialize_tables
acpi_tb_parse_root_table
acpi_tb_install_standard_table (4 invocations)
acpi_install_table
acpi_tb_install_standard_table
2. When it is invoked during the runtime, ACPICA mutex is used as
appropriate:
acpi_ex_load_op
acpi_tb_install_and_load_table
acpi_tb_install_standard_table
acpi_load_table
acpi_tb_install_and_load_table
acpi_tb_install_standard_table
The mutex is now used in acpi_tb_install_and_load_table(), while it actually
should be in acpi_tb_install_standard_table().
This introduces another problem in acpi_tb_install_standard_table() where
acpi_gbl_table_handler is invoked from and the lock contexts are thus not
consistent for the table handlers. This triggers a regression when
acpi_get_table()/acpi_put_table() start to hold table mutex during runtime.
The regression is noticed by LKP as new errors reported by ACPICA mutex
debugging facility.
[ 2.043693] ACPI Error: Mutex [ACPI_MTX_Tables] already acquired by this thread [497483776] (20160930/utmutex-254)
[ 2.054084] ACPI Error: Mutex [0x2] is not acquired, cannot release (20160930/utmutex-326)
And it triggers a deadlock:
[ 247.066214] INFO: task swapper/0:1 blocked for more than 120 seconds.
...
[ 247.091271] Call Trace:
...
[ 247.121523] down_timeout+0x47/0x50
[ 247.125065] acpi_os_wait_semaphore+0x47/0x62
[ 247.129475] acpi_ut_acquire_mutex+0x43/0x81
[ 247.133798] acpi_get_table+0x2d/0x84
[ 247.137513] acpi_table_attr_init+0xcd/0x100
[ 247.146590] acpi_sysfs_table_handler+0x5d/0xb8
[ 247.151174] acpi_bus_table_handler+0x23/0x2a
[ 247.155583] acpi_tb_install_standard_table+0xe0/0x213
[ 247.164489] acpi_tb_install_and_load_table+0x3a/0x82
[ 247.169592] acpi_ex_load_op+0x194/0x201
...
[ 247.200108] acpi_ns_evaluate+0x1bb/0x247
[ 247.204170] acpi_evaluate_object+0x178/0x274
[ 247.213249] acpi_processor_set_pdc+0x154/0x17b
...
The table mutex is held in acpi_tb_install_and_load_table() and is re-visited by
acpi_get_table().
Noticing that the early mutex requirement actually belongs to the OSL layer
and has already been handled in acpi_os_wait_semaphore()/acpi_os_signal_semaphore(),
the regression canbe fixed by removing this hidden logic from the ACPICA core
to the OS-specific code.
Fixes: 174cc7187e6f ("ACPICA: Tables: Back port acpi_get_table_with_size() and early_acpi_os_unmap_memory() from Linux kernel")
Reported-and-tested-by: Tomi Sarvela <tomi.p.sarvela@intel.com>
Reported-by: Ye Xiaolong <xiaolong.ye@intel.com>
Signed-off-by: Lv Zheng <lv.zheng@intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
A side effect of keeping intel_pstate sysfs limits in sync with cpufreq
is that the now sysfs limits can't enforced under performance policy.
For example, if the max_perf_pct is changed from 100 to 80, this will call
intel_pstate_set_policy(), which will change the max_perf to 100 again for
performance policy. Same issue happens, when no_turbo is set.
This change calculates max and min frequency using sysfs performance
limits in intel_pstate_verify_policy() and adjusts policy limits by
calling cpufreq_verify_within_limits().
Also, it causes the setting of performance limits to be skipped if
no_turbo is set.
Fixes: 111b8b3fe4fa (cpufreq: intel_pstate: Always keep all limits settings in sync)
Signed-off-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Revert commit 08b98d329165 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0
flag) as it caused system suspend (in the default configuration) to fail
on Dell XPS13 (9360) with the Kaby Lake processor.
Fixes: 08b98d329165 (PM / sleep / ACPI: Use the ACPI_FADT_LOW_POWER_S0 flag)
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Olof Johansson:
"We've been sitting on fixes for a while, and they keep trickling in at
a low rate. Nothing in here comes across as particularly scary or
noteworthy, for the most part it's a large collection of small DT
tweaks"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (24 commits)
ARM: dts: da850-evm: fix read access to SPI flash
ARM: dts: omap3: Fix Card Detect and Write Protect on Logic PD SOM-LV
ARM64: dts: meson-gxbb-odroidc2: Disable SCPI DVFS
ARM: dts: OMAP5 / DRA7: indicate that SATA port 0 is available.
ARM: dts: NSP: Fix DT ranges error
ARM: multi_v7_defconfig: set bcm47xx watchdog
ARM: multi_v7_defconfig: fix config typo
ARM: dts: dra72-evm-revc: fix typo in ethernet-phy node
soc: ti: wkup_m3_ipc: Fix error return code in wkup_m3_ipc_probe()
ARM: ux500: fix prcmu_is_cpu_in_wfi() calculation
ARM: dts: sunxi: Change node name for pwrseq pin on Olinuxino-lime2-emmc
ARM: dts: sun8i: Support DTB build for NanoPi M1
ARM: dts: sun6i: hummingbird: Enable display engine again
ARM: dts: sun6i: Disable display pipeline by default
ARM, ARM64: dts: drop "arm,amba-bus" in favor of "simple-bus" part 3
ARM: dts: imx6qdl-nitrogen6_som2: fix sgtl5000 pinctrl init
ARM: dts: imx6qdl-nitrogen6_max: fix sgtl5000 pinctrl init
ARM: OMAP1: DMA: Correct the number of logical channels
ARM: dts: am335x-icev2: Remove the duplicated pinmux setting
ARM: OMAP2+: Fix WL1283 Bluetooth Baud Rate
...
|
|
Declare virtio_config_ops structure as const as it is only stored in the
config field of a virtio_device structure. This field is of type const, so
virtio_config_ops structures having this property can be declared const.
Done using Coccinelle:
@r1 disable optional_qualifier@
identifier i;
position p;
@@
static struct virtio_config_ops i@p={...};
@ok1@
identifier r1.i;
position p;
struct virtio_ccw_device x;
@@
x.vdev.config=&i@p
@bad@
position p!={r1.p,ok1.p};
identifier r1.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r1.i;
@@
+const
struct virtio_config_ops i;
File size before and after applying the patch remains the same.
text data bss dec hex filename
9235 296 32928 42459 a5db drivers/s390/virtio/virtio_ccw.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Message-Id: <1484333336-13443-1-git-send-email-bhumirks@gmail.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Trival fix, dev_err message is missing a \n, so add it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Message-Id: <20160927200844.16008-1-colin.king@canonical.com>
Signed-off-by: Christian Borntraeger <borntraeger@de.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
As virtio-1 introduced the possibility of the device manipulating the
status byte, revision 2 of the virtio-ccw transport introduced a means
of getting the status byte from the device via READ_STATUS. Let's wire
it up for revisions >= 2 and fall back to returning the stored status
byte if not supported.
Signed-off-by: Pierre Morel <pmorel@linux.vnet.ibm.com>
Signed-off-by: Cornelia Huck <cornelia.huck@de.ibm.com>
|
|
Using control_work instead of config_work as the 3rd argument to
container_of results in an invalid portdev pointer. Indeed, the work
structure is initialized as below:
INIT_WORK(&portdev->config_work, &config_work_handler);
It leads to a crash when portdev->vdev is dereferenced later. This
bug
is triggered when the guest uses a virtio-console without multiport
feature and receives a config_changed virtio interrupt.
Signed-off-by: G. Campana <gcampana@quarkslab.com>
Reviewed-by: Amit Shah <amit.shah@redhat.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
This is to silence an uninitialized variable warning in debug output.
The problem is this line:
pr_debug("vhost_get_vq_desc: head: %d, out: %u in: %u\n",
head, out, in);
If "head == vq->num" is true on the first iteration then "out" and "in"
aren't initialized. We handle that a few lines after the printk. I was
tempted to just delete the pr_debug() but I decided to just initialize
them to zero instead.
Also checkpatch.pl complains if variables are declared as just
"unsigned" without the "int".
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
Declare target_core_fabric_ops strucrues as const as they are only
passed as an argument to the functions target_register_template and
target_unregister_template. The arguments are of type const struct
target_core_fabric_ops *, so target_core_fabric_ops structures having
this property can be declared const.
Done using Coccinelle:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct target_core_fabric_ops i@p={...};
@ok@
position p;
identifier r.i;
@@
(
target_register_template(&i@p)
|
target_unregister_template(&i@p)
)
@bad@
position p!={r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
+const
struct target_core_fabric_ops i;
File size before: drivers/vhost/scsi.o
text data bss dec hex filename
18063 2985 40 21088 5260 drivers/vhost/scsi.o
File size after: drivers/vhost/scsi.o
text data bss dec hex filename
18479 2601 40 21120 5280 drivers/vhost/scsi.o
Signed-off-by: Bhumika Goyal <bhumirks@gmail.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Jason Wang <jasowang@redhat.com>
|
|
A user noticed that write performance was horrible over loopback and we
traced it to an inversion of when we need to set MSG_MORE. It should be
set when we have more bvec's to send, not when we are on the last bvec.
This patch made the test go from 20 iops to 78k iops.
Signed-off-by: Josef Bacik <jbacik@fb.com>
Fixes: 429a787be679 ("nbd: fix use-after-free of rq/bio in the xmit path")
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Reorder update stats flow to update most important counters last,
to get more accurate results.
New update order:
- PCIe counters
- Port counters
- Vport counters
- Queue counters
- Software counters
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
|
|
The caps structure consists of hca caps and port/management caps,
all under one roof.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This patch exposes PCIe performance counters, queried with
ethtool -S <devname>.
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Use ethtool -S to query physical layer statistical counters including:
- rx_symbol_errors_phy: Number of symbol errors that were not corrected
by FEC correction algorithm or that FEC was not active on this interface.
- rx_corrected_bits_phy: Number of corrected bits according to active
FEC (RS/FC).
Signed-off-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
