| Age | Commit message (Collapse) | Author |
|---|
|
This patch adds ability to switch beetween two PHY SGMII modes.
Some hardware, for example, FPGA IP designs may use 6-wire mode
which enables differential SGMII clock to MAC.
Signed-off-by: Vitaly Gaiduk <vitaly.gaiduk@cloudbear.ru>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A negative number of devices is nonsensical, so change the type to
unsigned. If the number of devices is 0, it is impossible for userspace
to interact with the module, so refuse loading the driver for that case.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
The name of the module is "null_blk", not "null". Make `pr_info()` follow
the pattern of `pr_err()` log messages.
Signed-off-by: André Almeida <andrealmeid@collabora.com>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Unit of 'chunk_size' is byte, instead of sector, so fix it by setting
the queue_limits' max_discard_sectors to rs->md.chunk_sectors. Also,
rename chunk_size to chunk_size_bytes.
Without this fix, too big max_discard_sectors is applied on the request
queue of dm-raid, finally raid code has to split the bio again.
This re-split done by raid causes the following nested clone_endio:
1) one big bio 'A' is submitted to dm queue, and served as the original
bio
2) one new bio 'B' is cloned from the original bio 'A', and .map()
is run on this bio of 'B', and B's original bio points to 'A'
3) raid code sees that 'B' is too big, and split 'B' and re-submit
the remainded part of 'B' to dm-raid queue via generic_make_request().
4) now dm will handle 'B' as new original bio, then allocate a new
clone bio of 'C' and run .map() on 'C'. Meantime C's original bio
points to 'B'.
5) suppose now 'C' is completed by raid directly, then the following
clone_endio() is called recursively:
clone_endio(C)
->clone_endio(B) #B is original bio of 'C'
->bio_endio(A)
'A' can be big enough to make hundreds of nested clone_endio(), then
stack can be corrupted easily.
Fixes: 61697a6abd24a ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org
Signed-off-by: Ming Lei <ming.lei@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The code assumes log_num < in_num everywhere, and that is true as long as
in_num is incremented by descriptor iov count, and log_num by 1. However
this breaks if there's a zero sized descriptor.
As a result, if a malicious guest creates a vring desc with desc.len = 0,
it may cause the host kernel to crash by overflowing the log array. This
bug can be triggered during the VM migration.
There's no need to log when desc.len = 0, so just don't increment log_num
in this case.
Fixes: 3a4d5c94e959 ("vhost_net: a kernel-level virtio server")
Cc: stable@vger.kernel.org
Reviewed-by: Lidong Chen <lidongchen@tencent.com>
Signed-off-by: ruippan <ruippan@tencent.com>
Signed-off-by: yongduan <yongduan@tencent.com>
Acked-by: Michael S. Tsirkin <mst@redhat.com>
Reviewed-by: Tyler Hicks <tyhicks@canonical.com>
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
|
|
iovec addresses coming from vhost are assumed to be
pre-validated, but in fact can be speculated to a value
out of range.
Userspace address are later validated with array_index_nospec so we can
be sure kernel info does not leak through these addresses, but vhost
must also not leak userspace info outside the allowed memory table to
guests.
Following the defence in depth principle, make sure
the address is not validated out of node range.
Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Cc: stable@vger.kernel.org
Acked-by: Jason Wang <jasowang@redhat.com>
Tested-by: Jason Wang <jasowang@redhat.com>
|
|
The software node is searched from a list that may be empty
when the function is called. This makes sure that the
function returns NULL if the list is empty.
Fixes: 1666faedb567 ("software node: Add software_node_find_by_name()")
Reported-by: kbuild test robot <lkp@intel.com>
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Reviewed-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Tx code doesn't clear the descriptors' status after cleaning.
So, if the budget is larger than number of used elems in a ring, some
descriptors will be accounted twice and xsk_umem_complete_tx will move
prod_tail far beyond the prod_head breaking the completion queue ring.
Fix that by limiting the number of descriptors to clean by the number
of used descriptors in the Tx ring.
'ixgbe_clean_xdp_tx_irq()' function refactored to look more like
'ixgbe_xsk_clean_tx_ring()' since we're allowed to directly use
'next_to_clean' and 'next_to_use' indexes.
CC: stable@vger.kernel.org
Fixes: 8221c5eba8c1 ("ixgbe: add AF_XDP zero-copy Tx support")
Signed-off-by: Ilya Maximets <i.maximets@samsung.com>
Tested-by: William Tu <u9012063@gmail.com>
Tested-by: Eelco Chaudron <echaudro@redhat.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
There were a couple cases where the ITR value generated via the adaptive
ITR scheme could exceed 126. This resulted in the value becoming either 0
or something less than 10. Switching back and forth between a value less
than 10 and a value greater than 10 can cause issues as certain hardware
features such as RSC to not function well when the ITR value has dropped
that low.
CC: stable@vger.kernel.org
Fixes: b4ded8327fea ("ixgbe: Update adaptive ITR algorithm")
Reported-by: Gregg Leventhal <gleventhal@janestreet.com>
Signed-off-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When the RX rings are created they are also populated with buffers
so that packets can be received. Usually these are kernel buffers,
but for AF_XDP in zero-copy mode, these are user-space buffers and
in this case the application might not have sent down any buffers
to the driver at this point. And if no buffers are allocated at ring
creation time, no packets can be received and no interrupts will be
generated so the NAPI poll function that allocates buffers to the
rings will never get executed.
To rectify this, we kick the NAPI context of any queue with an
attached AF_XDP zero-copy socket in two places in the code. Once
after an XDP program has loaded and once after the umem is registered.
This take care of both cases: XDP program gets loaded first then AF_XDP
socket is created, and the reverse, AF_XDP socket is created first,
then XDP program is loaded.
Fixes: 0a714186d3c0 ("i40e: add AF_XDP zero-copy Rx support")
Signed-off-by: Magnus Karlsson <magnus.karlsson@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Don't populate the array API on the stack but instead make it
static const. Makes the object code smaller by 58 bytes.
Before:
text data bss dec hex filename
82969 9763 256 92988 16b3c ixgbevf/ixgbevf_main.o
After:
text data bss dec hex filename
82815 9859 256 92930 16b02 ixgbevf/ixgbevf_main.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Currently iavf unconditionally applies MAC address change requests. This
brings the VF in a state where it is no longer able to pass traffic if
the PF rejects a MAC filter change for the VF.
A typical scenario for a rejected MAC filter is for an untrusted VF to
request to change the MAC address when an administratively set MAC is
present.
To keep iavf working in this scenario the MAC filter handling in iavf
needs to act on the PF reply regarding the MAC filter change. In the
case of an ack the new MAC address gets set, whereas in the case of a
nack the previous MAC address needs to stay in place.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In the case of an invalid min Tx rate being requested
i40e_ndo_set_vf_bw() immediately returns -EINVAL instead of releasing
__I40E_VIRTCHNL_OP_PENDING first.
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The macros used to specify the cloud filter fields are intended to be
individual bits. Declare them using the BIT() macro to make their
intention a little more clear.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
When variable "req_fec, fec, an" are empty,
dmesg shows log with "Requested FEC: , Negotiated FEC: , Autoneg:".
Add link dmesg log for cards without FEC.
Signed-off-by: Czeslaw Zagorski <czeslawx.zagorski@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The "Negotiated" string in i40e_print_link_message() function was missed.
This string has been added to the dmesg and small refactoring done removing
common substrings and unifying link status message format.
Without this patch it was not clear that FEC is related to negotiated FEC.
Signed-off-by: Aleksandr Loktionov <aleksandr.loktionov@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Mark bits 0xD through 0xF for the command flags of a cloud filter as
reserved. These bits are not yet defined and are considered as reserved
in the data sheet.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
The bit 0x0001 used in the cloud filters adminq command is reserved, and
is not actually a valid type.
The Linux driver has never used this type, and it's not clear if any
driver ever has.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Remove a call to ktime_to_timespec64 by calling ktime_get_real_ts64
directly.
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
Use the common api, and don't access queue_mapping directly.
Signed-off-by: Tonghao Zhang <xiangxia.m.yue@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
While testing VF spawn/destroy the following panic occurred.
BUG: unable to handle kernel NULL pointer dereference at 0000000000000029
[...]
Workqueue: i40e i40e_service_task [i40e]
RIP: 0010:i40e_sync_vsi_filters+0x6fd/0xc60 [i40e]
[...]
Call Trace:
? __switch_to_asm+0x35/0x70
? __switch_to_asm+0x41/0x70
? __switch_to_asm+0x35/0x70
? _cond_resched+0x15/0x30
i40e_sync_filters_subtask+0x56/0x70 [i40e]
i40e_service_task+0x382/0x11b0 [i40e]
? __switch_to_asm+0x41/0x70
? __switch_to_asm+0x41/0x70
process_one_work+0x1a7/0x3b0
worker_thread+0x30/0x390
? create_worker+0x1a0/0x1a0
kthread+0x112/0x130
? kthread_bind+0x30/0x30
ret_from_fork+0x35/0x40
Investigation revealed a race where pf->vf[vsi->vf_id].trusted may get
accessed by the watchdog via i40e_sync_filters_subtask() although
i40e_free_vfs() already free'd pf->vf.
To avoid this the call to i40e_sync_vsi_filters() in
i40e_sync_filters_subtask() needs to be guarded by __I40E_VF_DISABLE,
which is also used by i40e_free_vfs().
Note: put the __I40E_VF_DISABLE check after the
__I40E_MACVLAN_SYNC_PENDING check as the latter is more likely to
trigger.
CC: stable@vger.kernel.org
Signed-off-by: Stefan Assmann <sassmann@kpanic.de>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
In ixgbe_configure_clsu32(), 'jump', 'input', and 'mask' are allocated
through kzalloc() respectively in a for loop body. Then,
ixgbe_clsu32_build_input() is invoked to build the input. If this process
fails, next iteration of the for loop will be executed. However, the
allocated 'jump', 'input', and 'mask' are not deallocated on this execution
path, leading to memory leaks.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
|
|
available
The downside of guest side polling is that polling is performed even
with other runnable tasks in the host. However, even if poll in kvm
can aware whether or not other runnable tasks in the same pCPU, it
can still incur extra overhead in over-subscribe scenario. Now we can
just enable guest polling when dedicated pCPUs are available.
Acked-by: Paolo Bonzini <pbonzini@redhat.com>
Signed-off-by: Wanpeng Li <wanpengli@tencent.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
cpuidle-haltpoll can be built as a module to allow optional late load.
Given we are setting @owner to THIS_MODULE, cpuidle will attempt to grab a
module reference every time a cpuidle_device is registered -- so
essentially all online cpus get a reference.
This prevents for the module to be unloaded later, which makes the
module_exit callback entirely unused. Thus remove the @owner and allow
module to be unloaded.
Fixes: fa86ee90eb11 ("add cpuidle-haltpoll driver")
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
When a user loads cpuidle-haltpoll on a non KVM guest the module will
successfully load, even though idle driver registration didn't take
place.
We should instead return -ENODEV signaling the user that the driver can't
be loaded, like other error paths in haltpoll_init(). An example of such
error paths is when we return -EBUSY when attempting to register an idle
driver when it had one already (e.g. intel_idle loads at boot and then we
attempt to insert module cpuidle-haltpoll).
Fixes: fa86ee90eb11 ("add cpuidle-haltpoll driver")
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Right now, guest current governors have the following ratings:
* ladder -> 10
* teo -> 19
* menu -> 20
* haltpoll -> 21
* ladder + nohz=off -> 25
haltpoll governor got introduced and it is now the default governor given
its highest rating -- with ladder+nohz being the exception -- regardless of
idle driver in the guest. An example of an undesirable case is x86 KVM
guests with MWAIT which have intel_idle registered first, and consequently
will have haltpoll be used as governor which would get limited to a poll
state and state 1 and the other states wouldn't get used.
To keep the previous defaults we decrease rating of governor to 9 (below
current lowest rating) and thus rely on @governor switch on
cpuidle_register_driver() to tie in haltpoll idle driver and governor
together.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The recently introduced haltpoll driver is largely only useful with
haltpoll governor. To allow drivers to associate with a particular idle
behaviour, add a @governor property to 'struct cpuidle_driver' and thus
allow a cpuidle driver to switch to a *preferred* governor on idle driver
registration. We save the previous governor, and when an idle driver is
unregistered we switch back to that.
The @governor can be overridden by cpuidle.governor= boot param or
alternatively be ignored if the governor doesn't exist.
Signed-off-by: Joao Martins <joao.m.martins@oracle.com>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
|
|
|
|
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_TX flag.
When performing an RX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer which is copied to the TX FIFO.
The dummy buffer is necessary because the chip is not capable of
automatically clocking out null bytes.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which fills the TX FIFO by cyclically copying
from the zero page. The transaction requires very little CPU time to
submit and generates no interrupts while running. Specifics are
provided in kerneldoc comments.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/f45920af18dbf06e34129bbc406f53dc9c5d1075.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver currently sets the SPI_CONTROLLER_MUST_RX flag.
When performing a TX-only transfer, this flag causes the SPI core to
allocate and DMA-map a dummy buffer into which the RX FIFO contents are
copied. The dummy buffer is necessary because the chip is not capable
of disabling the receiver or automatically throwing away received data.
Not reading the RX FIFO isn't an option either since transmission is
halted once it's full.
Avoid the overhead induced by the dummy buffer by preallocating a
reusable DMA transaction which cyclically clears the RX FIFO. The
transaction requires very little CPU time to submit and generates no
interrupts while running. Specifics are provided in kerneldoc comments.
With a ks8851 Ethernet chip attached to the SPI controller, I am seeing
a 30 us reduction in ping time with this commit (1.819 ms vs. 1.849 ms,
average of 100,000 packets) as well as a 2% reduction in CPU time
(75:08 vs. 76:39 for transmission of 5 GByte over the SPI bus).
The commit uses the TX DMA interrupt to signal completion of a transfer.
This interrupt is raised once all bytes have been written to the
TX FIFO and it is then necessary to busy-wait for the TX FIFO to become
empty before the transfer can be finalized. As an alternative approach,
I have explored using the SPI controller's DONE interrupt to detect
completion. This interrupt is signaled when the TX FIFO becomes empty,
avoiding the need to busy-wait. However latency deteriorates compared
to the present commit and surprisingly, CPU time is slightly higher as
well:
It turns out that in 45% of the cases, no busy-waiting is needed at all
and in 76% of the cases, less than 10 busy-wait iterations are
sufficient for the TX FIFO to drain. This was measured on an RT kernel.
On a vanilla kernel, wakeup latency is worse and thus fewer iterations
are needed. The measurements were made with an SPI clock of 20 MHz,
they may differ slightly for slower or faster clock speeds.
Previously we always used the RX DMA interrupt to signal completion of a
transfer. Using the TX DMA interrupt now introduces a race condition:
TX DMA is always started before RX DMA so that bytes are already clocked
out while RX DMA is still being set up. But if a TX-only transfer is
very short, then the TX DMA interrupt may occur before RX DMA is set up.
If the interrupt happens to occur on the same CPU, setup of RX DMA may
even be delayed until after the interrupt was handled.
I've solved this by having the TX DMA callback clear the RX FIFO while
busy-waiting for the TX FIFO to drain, thus avoiding a dependency on
setup of RX DMA. Additionally, I am using a lock-free mechanism with
two flags, tx_dma_active and rx_dma_active plus memory barriers to
terminate RX DMA either by the TX DMA callback or immediately after
setting it up, whichever wins the race. I've explored an alternative
approach which temporarily disables the TX DMA callback until RX DMA
has been set up (using tasklet_disable(), local_bh_disable() or
local_irq_save()), but the performance was minimally worse.
[Nathan Chancellor contributed a DMA mapping fixup for an early version
of this commit, hence his Signed-off-by.]
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/874949385f28251e2dcaa9494e39a27b50e9f9e4.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 DMA controller is capable of synthesizing zeroes instead of
copying them from a source address. The feature is enabled by setting
the SRC_IGNORE bit in the Transfer Information field of a Control Block:
"Do not perform source reads.
In addition, destination writes will zero all the write strobes.
This is used for fast cache fill operations."
https://www.raspberrypi.org/app/uploads/2012/02/BCM2835-ARM-Peripherals.pdf
The feature is only available on 8 of the 16 channels. The others are
so-called "lite" channels with a limited feature set and performance.
Enable the feature if a cyclic transaction copies from the zero page.
This reduces traffic on the memory bus.
A forthcoming use case is the BCM2835 SPI driver, which will cyclically
copy from the zero page to the TX FIFO. The idea to use SRC_IGNORE was
taken from an ancient GitHub conversation between Martin and Noralf:
https://github.com/msperl/spi-bcm2835/issues/13#issuecomment-98180451
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/b2286c904408745192e4beb3de3c88f73e4a7210.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver needs to set up the clock polarity in its
->prepare_message() hook before spi_transfer_one_message() asserts chip
select to avoid a gratuitous clock signal edge (cf. commit acace73df2c1
("spi: bcm2835: set up spi-mode before asserting cs-gpio")).
Precalculate the CS register value (which selects the clock polarity)
once in ->setup() and use that cached value in ->prepare_message() and
->transfer_one(). This avoids one MMIO read per message and one per
transfer, yielding a small latency improvement. Additionally, a
forthcoming commit will use the precalculated value to derive the
register value for clearing the RX FIFO, which will eliminate the need
for an RX dummy buffer when performing TX-only DMA transfers.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/d17c1d7fcdc97fffa961b8737cfd80eeb14f9416.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
Document the BCM2835 DMA driver's device data structure so that upcoming
commits may add further members with proper kerneldoc.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/78648f80f67d97bb7beecc1b9be6b6e4a45bc1d8.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
__spi_alloc_controller() uses a single allocation to accommodate struct
spi_controller and the driver-private data, but places the latter behind
the former. This order does not guarantee cacheline alignment of the
driver-private data. (It does guarantee cacheline alignment of struct
spi_controller but the structure doesn't make any use of that property.)
Round up struct spi_controller to cacheline size. A forthcoming commit
leverages this to grant DMA access to driver-private data of the BCM2835
SPI master.
An alternative, less economical approach would be to use two allocations.
A third approach consists of reversing the order to conserve memory.
But Mark Brown is concerned that it may result in a performance penalty
on architectures that don't like unaligned accesses.
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/01625b9b26b93417fb09d2c15ad02dfe9cdbbbe5.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The DMA engine API requires DMA drivers to explicitly allow that
descriptors are prepared once and reused multiple times. Only a
single driver makes use of this functionality so far (pxa_dma.c,
to speed up pxa_camera.c).
We're about to add another use case for reusable descriptors in
the BCM2835 SPI driver, so allow that in the BCM2835 DMA driver.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Cc: Robert Jarzmik <robert.jarzmik@free.fr>
Link: https://lore.kernel.org/r/bfc98a38225bbec4158440ad06cb9eee675e3e6f.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 DMA driver currently requests an interrupt from the
controller regardless whether or not the client has passed in the
DMA_PREP_INTERRUPT flag. This causes unnecessary overhead for cyclic
transactions which do not need an interrupt after each period.
We're about to add such a use case, namely cyclic clearing of the SPI
controller's RX FIFO, so amend the DMA driver to request an interrupt
only if DMA_PREP_INTERRUPT was passed in. Ignore the period_len for
such transactions and set it to the buffer length to make the driver's
calculations work.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Vinod Koul <vkoul@kernel.org>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Cc: Florian Kauer <florian.kauer@koalo.de>
Link: https://lore.kernel.org/r/73cf37be56eb4cbe6f696057c719f3a38cbaf26e.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The BCM2835 SPI driver uses a flag to keep track of whether a DMA
transfer is in progress.
The flag is used to avoid terminating DMA channels multiple times if a
transfer finishes orderly while simultaneously the SPI core invokes the
->handle_err() callback because the transfer took too long. However
terminating DMA channels multiple times is perfectly fine, so the flag
is unnecessary for this particular purpose.
The flag is also used to avoid invoking bcm2835_spi_undo_prologue()
multiple times under this race condition. However multiple *concurrent*
invocations can no longer happen since commit 2527704d8411 ("spi:
bcm2835: Synchronize with callback on DMA termination") because the
->handle_err() callback now uses the _sync() variant when terminating
DMA channels.
The only raison d'être of the flag is therefore that
bcm2835_spi_undo_prologue() cannot cope with multiple *sequential*
invocations. Achieve that by setting tx_prologue to 0 at the end of
the function. Subsequent invocations thus become no-ops.
With that, the dma_pending flag becomes unnecessary, so drop it.
Tested-by: Nuno Sá <nuno.sa@analog.com>
Tested-by: Noralf Trønnes <noralf@tronnes.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Acked-by: Stefan Wahren <wahrenst@gmx.net>
Acked-by: Martin Sperl <kernel@martin.sperl.org>
Link: https://lore.kernel.org/r/062b03b7f86af77a13ce0ec3b22e0bdbfcfba10d.1568187525.git.lukas@wunner.de
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
In-between the MAC & PHY there can be a mode converter, which converts one
mode to another (e.g. GMII-to-RGMII).
The converter, can be passive (i.e. no driver or OS/SW information
required), so the MAC & PHY need to be configured differently.
For the `stmmac` driver, this is implemented via a `mac-mode` property in
the device-tree, which configures the MAC into a certain mode, and for the
PHY a `phy_interface` field will hold the mode of the PHY. The mode of the
PHY will be passed to the PHY and from there-on it work in a different
mode. If unspecified, the default `phy-mode` will be used for both.
Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a mlx4_err error message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a .msg literal string. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
MFW associates the entity id to a config attribute instead of assigning
one entity id for all the config attributes.
This patch incorporates driver changes to link entity id to a config id
attribute.
Fixes: 0dabbe1bb3a4 ("qed: Add driver API for flashing the config attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver currently returns max-buf-size as size of the config attribute.
This patch incorporates changes to read this value from MFW (if available)
and provide it to the user. Also did a trivial clean up in this path.
Fixes: d44a3ced7023 ("qede: Add support for reading the config id attributes.")
Signed-off-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Signed-off-by: Ariel Elior <aelior@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in the lmc_trace message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a spelling mistake in a dbg_verbose message. Fix it.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Don't populate the array degrees on the stack but instead make it
static const. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
5356 1560 0 6916 1b04 dw_mmc-hi3798cv200.o
After:
text data bss dec hex filename
5214 1656 0 6870 1ad6 dw_mmc-hi3798cv200.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
System suspend/resume of SDIO cards, with SDIO IRQs enabled and when using
MMC_CAP2_SDIO_IRQ_NOTHREAD is unfortunate still suffering from a fragile
behaviour. Some problems have been taken care of so far, but more issues
remains.
For example, calling the ->ack_sdio_irq() callback to let host drivers
re-enable the SDIO IRQs is a bad idea, unless the IRQ have been consumed,
which may not be the case during system suspend/resume. This may lead to
that a host driver re-signals the same SDIO IRQ over and over again,
causing a storm of IRQs and gives a ping-pong effect towards the
sdio_irq_work().
Moreover, calling the ->enable_sdio_irq() callback at system resume to
re-enable already enabled SDIO IRQs for the host, causes the runtime PM
count for some host drivers to become in-balanced. This then leads to the
host to remain runtime resumed, no matter if it's needed or not.
To fix these problems, let's check if process_sdio_pending_irqs() actually
consumed the SDIO IRQ, before we continue to ack the IRQ by invoking the
->ack_sdio_irq() callback.
Additionally, there should be no need to re-enable SDIO IRQs as the host
driver already knows if they were enabled at system suspend, thus also
whether it needs to re-enable them at system resume. For this reason, drop
the call to ->enable_sdio_irq() during system resume.
In regards to these changes there is yet another issue, which is when there
is an SDIO IRQ being signaled by the host driver, but after the SDIO card
has been system suspended. Currently these IRQs are just thrown away, while
we should at least make sure to try to consume them when the SDIO card has
been system resumed. Fix this by queueing a sdio_irq_work() after we system
resumed the SDIO card.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
